Home > POWER TOOLS & ACC > PNEUMATIC TOOLS & ACCESSORIES > COMPRESSORS & ACCESSORIES > AIR TOOLS
Sort By:
1
Tru-Flate 12-225 Air Line Plug Tru-Flate 12-125 Hose Plug Tru-Flate 12-235 Air Line Plug
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure.
Tru-Flate 12-325 Air Line Plug Tru-Flate 12-135 Air Line Nipple Tru-Flate 12-335 Air Line Plug
Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Intended for compressed airlines only. 300 PSI maximum rated working pressure. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Intended for compressed airlines only. 300 PSI maximum rated working pressure.
Tru-Flate 21-123 Air Hose Fitting Tru-Flate 21-535 Air Hose Bushing Tru-Flate 21-143 Air Hose Fitting
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. All brass, corrosion resistant material. Allows user to adjust thread sizes from 1/4" NPT through 3/8" NPT with either male or female ends. All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
Tru-Flate 21-133 Air Hose Fitting Tru-Flate 21-595 Hose Adapter with Ball Socket Tru-Flate 21-222 Air Hose Fitting
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. All brass, corrosion resistant material. Connects FPT to FPT. With ball socket. All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
Tru-Flate 21-242 Air Hose Fitting Tru-Flate 21-423 Barb Hose Splicer Tru-Flate 17-351 Ball Foot Direct Air Line Chuck
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. All brass construction resists rust and will not corrode as easily as other materials.  Precision machined to high quality standards.  Use with hose clamp or ferrules. Has a built-in shut-off valve and therefore cannot be used on inflator gauges.  Use when air supply lines come directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks.
Tru-Flate 21-505 Air Line Coupling Tru-Flate 21-467 Barb Hose Splicer Tru-Flate 12-425 Air Line Plug
Pipe couplings,thread adapters and bushings allows user to adjust thread sizes from 1/8" NPT through 1/2" NPT with either male or female ends. Corrosion resistant material. Connects FPT to FPT. All brass construction resists rust and will not corrode as easily as other materials.  Precision machined to high quality standards.  Use with hose clamp or ferrules. Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Tru-Flate 12-603 Air Line Plug Plews/Edelmann 12-227/6  Air Compressor Hose Fittings Tru-Flate 12-435 Air Line Plug
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Plug 1/4". I/M x 3/8" MNPT. Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Tru-Flate 21-147 Air Hose Fitting Tru-Flate 12-527 Air Line Plug Plews/Edelmann 12-611  Air Compressor Hose Fittings
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. Plug 3/8". TF x 1/4" FNPT.
Stanley TIRE-14F Tire Chuck Tru-Flate 12-605 Air Line Plug Tru-Flate 21-515 Air Line Coupling
Plated steel; corrosion resistant steel for long life. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Pipe coupling allows user to adjust thread sizes from 1/8" NPT through 1/2" NPT with either male or female ends. Corrosion resistant material. Connects MPT to MPT.
Plews/Edelmann 12-267/6  Air Compressor Hose Fittings Stanley 38M-14M Hex Reducer Nipple Plews/Edelmann 12-265  Air Compressor Hose Fittings
Plug 1/4". I/M 3/8" ID slim. Connects  FPT to FPT. Use thread sealant tape on all male threads for air tight connections. Plug 1/4". I/M x Barb 1/4" ID.
PLUG 3/8IN TF X 3/8IN FNPT    Tru-Flate 17-361 Ball Foot Direct Combination Air Line Chuck Tru-Flate 17-369 Ball Foot Direct Air Line Chuck
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Combination No. 17-350 chuck with 1/4" ID hose barb No. 21-123. Has a built-in shut-off valve and therefore cannot be used on inflator gauges.  Use when air supply lines comes directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks. Has a built in shut off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line.
Senco PC0101 Air Tool Oil Stanley AP-38F Auto Hose Adapter Stanley AP-38M Auto Hose Adapter
Premium-grade oil formulated with high-quality paraffin distillate stocks. Contains carefully balanced rust and oxidation inhibitors. Lubricates Pneumatic tools, protects against corrosion and extends part life. Plated steel construction with drag guard for job site durability and reliability. Large body size for maximum air flow and tool performance. Corrosion resistant steel for long life. Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections.
Stanley AP-14M Auto Hose Adapter Tru-Flate 12-705 Air Line Plug Stanley-Bostitch BTFP72333  Air Compressor Hose Swivel Plug - Male
Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections. Eight ball coupler design for balanced, strong, secure connections. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Swivel design minimizes hose twisting for improved control. Corrosion-resistant steel. Pre-applied thread connections.
SPLICER HOSE REUSABLE 1/4IN   HOSE AIR END REUSABLE 1/4IN   Tru-Flate 13-235 Industrial Air Line Coupler
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI.
Tru-Flate 13-225 Air Line Coupler Tru-Flate 17-355 Snap Clip On Air Line Chuck Stanley IC-14M Industrial Hose Adapter
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Snap-On Chuck Clip. Converts any single foot chuck to a clip-on chuck. Fits all standard ball foot chucks with .672-32 thread.  Holds chuck to tire valve while inflating. Hardened stainless steel locking balls for maximum performance. Corrosion resistant steel for long life. Pre-applied thread sealant for air tight connections.
Stanley IC-14F Industrial Hose Adapter Stanley-Bostitch BTFP72320  Air Compressor Hose FittingsSeries Coupler Stanley-Bostitch BTFP72321  Air Compressor Hose Coupler
Plated steel construction with drag guard for job site durability and reliability. Six ball coupler design for balanced, strong, secure connections. Corrosion resistant steel for long life. Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball design 1/4 coupler for balanced, strong and secure connections. Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball design 1/4 coupler for balanced, strong and secure connections.
SPLICER HOSE REUSABLE 3/8IN   COUPLER UNIVERSAL 1/4IN MPT   COUPLER UNIVERSAL 1/4IN FPT
Lightweight compact design. Last longer than standard couplers. 1/4" body size, fits Tru-Flate, Industrial/Milton and Aro 1/4" plugs. Lightweight compact design. Last longer than standard couplers. 1/4" body size, fits Tru-Flate, Industrial/Milton and Aro 1/4" plugs.
Tru-Flate 17-383 Dual Foot Direct Air Line Chuck Tru-Flate 13-135 Air Line Coupler Tru-Flate 13-125 Air Line Coupler
Built-in shut-off valve cannot be used on inflator gauges.  Use when air supply lines come directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks.  Extension for hard-to-reach dual wheel valves on tractors, trucks or bus. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Stanley Industrial IHKIT-14F Hose Coupler Kit Stanley HREPAIR-38 Hose Splice Kit Bostitch BTFP72327 Ball Drain Valve
Six hardened stainless steel locking balls for maximum performance. Corrosion resistant steel for long life. Kit Includes: (1) 1/4" MPT x barbed hose splicer for 3/8" hose ; (1) barb x barb hose splicer for 3/8" hose &  (3) Clamps. Turn ball type drain valve. 1/4" NPT male thread.
Senco PC0350 Standard Belt Hook SPLICER HOSE REUSABLE 1/2IN   HOSE AIR END REUSABLE 1/2IN
Fits pneumatic tools with a 1/4'' fitting. Hook nail gun on your tool belt to reduce damage and free up hands.
Tru-Flate 13-201 Coupler/Plug Set Tru-Flate 41-300 Hose Repair Kit Stanley TEE-14F Tee Fitting
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-225 1/4" Male NPT Plug and  No.13-235 1/4" Female NPT Coupler. Design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Contains all parts necessary to repair a direct air line hose assembly. Each kit contains: (1) Single Foot Air Chuck, 1/4" Female NPT, (1) Male Hose End 1/4" ID hose x 1/4" NPT, (1) Hose Splicer, 1/4" ID hose, (3) Band Style Hose Clamps, fits 3/8" ID hose Stanley Tee Fitting, 1/4 in Nominal, FNPT End, Brass
Nati 9390 Air Hose 25 ft Plews/Edelmann 13-138 Hose Coupling Tru-Flate 13-335 Air Line Coupler
Self storing design springs back into coiled shape. Rugged oil and abrasion resistant polyurethane construction. Leak resistant, 360 degree swivel brass end connectors. Spring bend restrictors prevent kinks near hose end. 1/4" NPT; maximum working pressure at 100 psi. Coupler 1/4". TF x 3/8" FNPT. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
HOSE AIR END REUSABLE 3/8IN   Tru-Flate 21-605 Barb Air Line Swivel Tru-Flate 17-353 Ball Foot Direct Clip On Air Line Chuck
Eliminates kinked and twisted air line hose by swiveling a full 360 degrees. Use on air lines, tools, and compressor connections to increase flexibility and convenience. 150 PSI maximum working pressure. Combination No. 17-350 chuck with No. 17-355 chuck clip. Has a built-in shut-off valve and therefore cannot be used on inflator gauges.  Use when air supply lines come directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks.
Plews/Edelmann 13-237 Hose Coupling Plews 4-25E-RET Recoil Air Hose Tru-Flate 13-101 Coupler/Plug Set
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI. Retains its self-coiling properties and stores itself when finished. Can be used with all air-powered equipment on the job site and in garages, plants and service stations. Swivel end fittings on one side reduce hose twist. Temperature range: 32-degree F to 120-degree F. 200 PSI. Yellow Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-125 1/4" Male NPT Plug and No.13-135 1/4" Female NPT Coupler. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI.
Tru-Flate 13-325 Air Line Coupler Senco PC0630 Belt Hook HOSE AIR END REUSABLE 1/4IN
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Fits pneumatic tools with 3/8'' fitting. Extra wide width. Hook nail gun to your belt to free up hands to reduce damage. Wide enough to fit over 2x4.
Bostitch Prozhoze Reusable Hose Repair Kit Tru-Flate 13-301 Coupler/Plug Set HOSE AIR ED RUSBL W/SWVL 3/8IN
Includes 1 mender and 1 threaded end fittings. Simple 3-step process: unscrew, cut and replace. Includes 1mender and 1 threaded end fitting. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-325 1/4" Male NPT Plug and No.13-335 1/4" Female Coupler.  Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI.
Mintcraft DZA019 Hose Coupler Set HOSE AIR ED RUSBL W/SWVL 1/2IN Tru-Flate 13-425 Air Line Coupler
3 piece 1/4" MPT quick plug; 1 piece 1/4" FPT quick plug; 1 piece 1/4"NPT quick coupler. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Available in sleeve type only.
Tru-Flate 17-373 Grip Tite Direct Air Line Chuck Tru-Flate 13-435 Air Line Coupler Stanley-Bostitch BTFP72318  Air Compressor Hose Fittings Plug - Male
Has a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks. Works like a ``quick coupler". Snaps onto any standard tire valve and stays put until released. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Available in sleeve type only. Pre-applied sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections.
Stanley-Bostitch BTFP72319  Air Compressor Hose Fittings Plug - Female Stanley UC38-14F Push-to-Connect Auto Hose Adapter Stanley UC38-14M Push-to-Connect Auto Hose Adapter
Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections. Accepts 3/8" series Industrial Interchange or 3/8" Automotive Interchange plugs. Eight Hardened stainless steel locking balls for maximum performance. Accepts 3/8" series Industrial Interchange or 3/8" Automotive Interchange plugs. Eight Hardened stainless steel locking balls for maximum performance.
Tru-Flate 13-537 Air Line Coupler Tru-Flate 13-203 Coupler/Plug Kit Plews/Edelmann 13-603 Hose Coupling
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI. (1) One Each:  1/4" FPT Coupler (13-235), 1/4" MPT Coupling (21-505), 1/4" MPT Plug (12-225) and 1/4" FPT Plug (12-235). Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Plews/Edelmann 13-605 Hose Coupling Tru-Flate 13-401 Coupler/Plug Set Tru-Flate 13-611 Air Line Coupler
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-425 1/4" Male NPT Plug.  Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. No.13-435 1/4" Female Coupler - Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Tru-Flate 13-613 Air Line Coupler HOSE AIR END REUSABLE 3/8IN   Plews 576-25A Air Hose
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Orange glo, long life engineered composition PVC hose. Spiral reinforced hose for durability. Nonconductive and oil and abrasion resistant; 1/4" NPT brass fittings on both ends.
Bostitch Prozhoze Reusable Hose Repair Kit Tru-Flate 13-527 Air Coupler Plews 4-50E-RET Recoil Air Hose
Includes 1 mender and 1 threaded end fittings. Simple 3-step process: unscrew, cut and replace. Includes 1mender and 1 threaded end fitting. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Retains its self-coiling properties and stores itself when finished. Can be used with all air-powered equipment on the job site and in garages, plants and service stations. Swivel end fittings on one side reduce hose twist. Temperature range: 32-degree F to 120-degree F. 200 PSI. Yellow
Tru-Flate 12-537 Air Hose Plug COUPLER-PLUG SET 4PC          Nati 9411 Air Hose 25 ft
COUPLER-PLUG SET 4PC
Our Price: $14.26
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. Hi Flo Couplers and Plugs increase air flow to ensure tools will provide maximum torque and optimal performance. Push-to-connect design is made of light-weight T6 aluminum. Includes (1) Female Coupler, (1) Female Plug and (2) Male Plugs. Ideal for a wide range of home and job-site applications. 3/8". Simple and convenient storing, without taking away the needed length required on the job-site. 300 psi.
HOSE AIR POLY BLUE 1/4INX25FT Tru-Flate 13-713 Air Line Coupler Muti 60605X Nailgun Hanger
Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Spring loaded and retractable. Solid steel with durable zinc plating. Keeps tools close by. For Use With: Hitachi: NR90AE, NR90AF, NR90AD; Stanley Bostitch: N88RH-2.
Plews 554-50A-10 Air Hose Plews 576-50A Air Hose Nati 9389 Air Hose 50 ft
Quality  multi-purpose air hose. Light weight, flexible, kink-resistant design. 300 PSI. Orange glo, long life engineered composition PVC hose. Spiral reinforced hose for durability. Nonconductive and oil and abrasion resistant; 1/4" NPT brass fittings on both ends. Self storing design springs back into coiled shape. Rugged oil and abrasion resistant polyurethane construction. Leak resistant, 360 degree swivel brass end connectors. Spring bend restrictors prevent kinks near hose end. 1/4" NPT; maximum working pressure at 100 psi.
Nati 50059 Air Hose 25 ft HOSE AIR 3/8X50FT             Plews 12-50E Poly Air Hose
HOSE AIR 3/8X50FT
Our Price: $20.91
Extremely lightweight and flexible air hose provides ideal performance in all climates. Solid brass fittings: 1/4" - 18 NPT. Oil and abrasion resistant. Heavy duty braided reinforcement. Working temperature range from 30 to 150 degrees F. Maximum working pressure of 250 psi. Ultra Air takes hybrid to a new level, offering increased cold weather flexibility over competitive hoses. When uncoiled, this hose lays flat making it easier to use with no interruption in air flow or tripping hazards. Lighter in weight than rubber and more flexible than PVC; features bend restrictors. Stays flexible, -40 to 150 degrees F. 300 PSI. Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI.
Nati 9412 Air Hose 50 ft Prohoze HOPB1450 Air Hose Stanley N66C-RK Repair Rebuild Kit
Ideal for a wide range of home and job-site applications. 3/8". Simple and convenient storing, without taking away the needed length required on the job-site. 300 psi. All weather flexibility with working temperature range of -40 degrees to 164 degrees F. Heavy duty reinforced braided hose designed with contractor in mind. 300 psi max working pressure with 900 psi burst strength for toughness and safety. End restraints designed for longer hose life. All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced. Special lubricant is provided with every o-ring kit. Rebuild Kit for N66C Model (630.2483).
Stanley 9B12062R Fuel Cell Plews 576-100A-5 Air Hose Stanley TVA6 Trigger Valve Kit
Use this fuel cell with Bostitch, Paslode, and Hitachi Cordless Finish Nailers. Averages 1,100 shots. Contains synthetic lubricants for optimal tool operation. Orange glo, long life engineered composition PVC hose. Spiral reinforced hose for durability. Nonconductive and oil and abrasion resistant; 1/4" NPT brass fittings on both ends. Fits N50, N55, N57, N60, N63, N65, N70, N80, N86, N90; Also N100, 650, 750, 850, 863, T55, T60, RN45, N95RHN. Kit includes: Bostitch TVA6 trigger assembly ,Valve assembly , Lubricant , Two orifice caps. Spring pin punch, Complete instructions.
Thermoid 522-25 Coupled Air Hose Thermoid 538-25 Coupled Air Hose Mintcraft ATA-052-1 Hose Plug
Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure. Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure. High speed steel.
Mintcraft ATA-053-A Hose Plug Stanley TVA11 Trigger Valve Stanley F N89ORK O-Ring Kit
Dependable male steel mechanical fitting is perfect for rapidly and securely separating air hoses. Replaces worn or broken trigger valve for Stanley Bostitch Nos.N52FN, N62FN, N79RH, N79WW, N80SB, N88WW, N88PC, N90PT, N95RHN nailers. Kit includes: TVA11, Roll Pin., and Lubricant. Contains all o-rings necessary to rebuild the F21, F28, F33, N89C tools. Does not include trigger valve or trigger valve o-rings.
North American 7637 Speedway Air Ratchet Wrenches Prohoze HOPB14100 Air Hose Plews 12-100E Air Hose
45 ft-lbs torque range. 4 cfm's at 90 psi. Minimum hose diameter is 3/8". All weather flexibility with working temperature range of -40 degrees to 164 degrees F. Heavy duty reinforced braided hose designed with contractor in mind. 300 psi max working pressure with 900 psi burst strength for toughness and safety. End restraints designed for longer hose life. Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI.
Stanley ORK13 O-Ring Repair Kit Hitachi 728982 Fuel Cell Senco PC1195 Mini Hand Nailer
All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced making a tool in otherwise good condition 'like new'. Special lubricant is provided with every o-ring kit. Contains all o-rings necessary to rebuild the:  RN45. Injects gas into nailer. 1,200 nails per fuel rod. Use with NR90GC (877.4366)  and NR90GR (775.0334) Hitatchi nailers. Powerful enough to drive bulk nails into joist hangers, hurricane straps, fencing or decking. Fifty percent lighter than traditional palm nailers and is ideal for exceptionally tight spots. Specifications; Reg. Operating Pressure: 60-110 psi (4.-7.6 bar). Air Consumption: 2 - 4 scfm. Length: 2 3/4" (69.9 mm); Width: 2" (55.6 mm). Fastener Specifications: Drives 2" - 3-1/2", 6d to 16d Bulk Nails. Includes Wrench. Tool Oil Required. Aluminum Housing & Rear Exhaust.
Stanley RN46-RK Repair Rebuild Kit AIR HOSE PROFLEX 1/4IN X 50FT Abbott Rubber 1502-38X50MM Air Hose 50 ft
All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced. Special lubricant is provided with every o-ring kit. Rebuild kit for No.RN46 (225.1452) . Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings. Rubber hose, durable, abrasion resistant.
Prohoze PRO-1450 Air Hose Ingersoll-Rand EC400-NS  Needle Scaler Plews 13-50AE Air Hose
Rugged reinforced polyurethane construction is abrasion, puncture and chemical-resistant. Flexible from -40 to 160 degrees F for revolutionary workability. Reusable 1/4" MPT fittings are field repairable in three easy steps. Non-marring translucent material provides a clear view of airline contaminants. Hi-vis safety yellow color for improved jobsite visibility. Snap-fit strain reliefs provide flexible reinforcement for extended life. Up to 2x lighter than standard air hoses. Ribbed design prevents hose from sticking to itself or other jobsite obstructions. Change your air hammer into a needle scaler with a twist of the arm. It gives you the versatility you need to fly through real work. For use with the Ingersoll Rand 114GQC Air Hammer. Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI.
Edge 3107G Pneumatic Die Grinder Stanley ORK11 O-Ring Kit Thermoid 522-50 Coupled Air Hose
Die grinder features a composite housing for durability and powerful 1/4 HP motor. Specs: RPM: 27,000, Air Inlet Size : 1/4", Min. Hose Size:  3/8", Collet Size (in.): 1/4, Side Handle: No: Durable composite housing Ball bearing construction 1/4 HP motor Self-locking throttle. All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Special lubricant is provided with every o-ring kit. Contains all o-rings necessary to rebuild the:  N80, N90 . Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure.
Plews 552-50AK-5 Air Hose Kit Stanley PN50 Mini Impact Nailer Thermoid 538-50 Coupled Air Hose
Quality rubber air hose. 300 PSI. Comes with bonus blow gun kit . Use in  garage, shop, industry,  or home. Includes: Safety blow gun, coupler and plugs, 5 different tips. Rubber grip designed to insulate and reduce vibration; 360 degree swivel air fitting for maximum accessibility. Front exhaust directs air away from users palm. Fastener Specifications: Drives Most Common Bulk Finish, Framing & Timber Nails. Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure.
AIR HOSE PROFLEX 3/8IN X 50FT Ingersoll-Rand 114GQC Air Hammer Ingersoll-Rand 301B Air Angle Die Grinders
Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings. Medium barrel length with built-in power regulator, professional touch trigger. Designed for exhaust work, cutting  metals, chipping and scraping surfaces. Specs:  Delivers 3,500 BPM., 11/16" bore diameter, 2-5/8" stroke length, 4 CFM, 1/4" air inlet, 3/8" minimum hose size. Includes  chisel shank size .401. Lightweight, durable and maneuverable. Comfortable composite grip is ideal for a variety of applications including porting, weld breaking, de-burring, polishing and grinding. Powerful motor delivers 0.33 hp (0.25 kw) and 25,000 rpm free speed. Integral safety lock throttle lever prevents accidental start-up. Tool comes with 1/4" and 6 mm collets and 2 wrenches. Rear exhaust directs air away from the operator.  Built in lubricating wick increases angle gear life. Composite housing protects tool from cold air and offers greater operator comfort. Durable ball bearing construction improves balance, reduces vibration and ensures longer life.
Mintcraft ATA-050 Air Hose Connector Mintcraft TA-054 Air Hose End Mintcraft ATA-057 Hose Plug
Brass. Mintcraft Air Hose End, 1/4 in Nominal, MNPT End, 3/8 in Inside Diameter Mintcraft Hose Plug, 1/4 in Nominal, MNPT End, Brass
Abbott Rubber 1010-03825-50-4MM Quick Connect Air Hose 50 ft Stanley WINTEROIL-4OZ Winter Grade Pneumatic Tool Lubricant Mintcraft ATA-0561 Air Line Connector
Rubber hose, durable, abrasion resistant. Prevents moisture coming into the tool from freezing. Brass.
Mintcraft ATA-0243L Barb Hose Splicer Ingersoll-Rand 317A Hi Speed Sanders AIR HOSE PROFLEX 1/4IN X 100FT
All brass. For small jobs and hard to reach places. Ideal for light sanding, feather edging and rust removal. 18,000 rpm, 0.45 hp (0.35 kw) motor. Easy to handle, compact and lightweight. Built-in power regulator. Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings.
Edge 3101G Pneumatic Die Grinder Ingersoll-Rand 170G Air Ratchet Wrenches Prohoze PRO-14100 Air Hose
Can be used in various applications including porting, weld breaking, deburring, polishing and grinding. Self-locking lever throttle. Grease fitting for increased angle gear life. Ergonomic grip. 20,000 rpm. Rear exhaust. 1/4" collet output. 1.8 m/s2 vibration. 3 CFM average air consumption. 18 CFM air consumption at load. 1/4" air inlet size. Variable speed throttle. Heat treated head for durability. Comfortable ergonomic grip. Ideal for general engine repair, home projects and light industrial applications. Specs:3/8" chuck size, 170 RPM, 55 ft. lbs. max torque, 4 CFM at PSI, 90 max pressure, 3/8" max bolt capacity, 1/4" inlet NPT. Rugged reinforced polyurethane construction is abrasion, puncture and chemical-resistant. Flexible from -40 to 160 degrees F for revolutionary workability. Reusable 1/4" MPT fittings are field repairable in three easy steps. Non-marring translucent material provides a clear view of airline contaminants. Hi-vis safety yellow color for improved jobsite visibility. Snap-fit strain reliefs provide flexible reinforcement for extended life. Up to 2x lighter than standard air hoses. Ribbed design prevents hose from sticking to itself or other jobsite obstructions.
Abbott Rubber 1025-0750R-50-CRS 2-Lug Air Hose 50 ft Edge 311G Dual Action Pneumatic Sander Senco PC0781 Hand Nailer
Rubber hose, durable, abrasion resistant. Variable speed sander with built-in power regulator, handle control, and 6" pad. Used for body shop and metal or wood preparation. Specs: CFM 4, CFM at Load 17, speed (RPM) 10,000, air inlet size (NPT) 1/4", and min. hose size 3/8". Fits in the palm of the hand, making it ideal for joust hangers, metal straps and pole barn assembly. Leather grip with soft rubber palm pad reduces fatigue. Magnetic nail guide for faster and easier driving. Specifications: 50 - 125 psi (3.5-8.4 bar). Height: 5.8"; Weight: 2.4 lb. Fastener Specifications: Drives Bulk Nails from 5d to 70d. Includes Leather grip.
Plews 13-100AE Air Hose Stanley BT200-RK Repair Rebuild Kit Plews 510HR-RET Retractable Air Hose
Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI. All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced. Special lubricant is provided with every o-ring kit.  Rebuild kit for BT200 model. All steel construction for industrial applications. Spring powered auto rewind. Ideal for mounting of wall, floor or ceiling. Guide arm adjustable for different angles. Valve assembly handles up to 250 PSI and 25 cfm. Locking ratchet brake.
Ingersoll-Rand EC300  Air Nibbler Edge 300G Random Pneumatic Sander Stanley PN100K Air Impact Nailer Kit
The Ingersoll Rand Edge 2.0 nibbler offers the ability to cut up to 18 gauge steel, aluminum, plastic or other metals in 6' per minute. Ergonomic grip. Angle head for easy cutting. Low profile throttle lever. 1/4" radius with ideal accuracy gives you the control and cutting power you need without the distorted edges. Variable Speed. Produces swirl-free finish. Lightweight, low vibration composite design. Contoured grip. Specs: Air Consumption (CFM):16; CFM at Load: 15.5; Speed (RPM): 10,000; Air Inlet Size (NPT): 1/4" ; Min. Hose Size: 5/16". Includes: 360 degree swivel vacuum adapter that provides greater range of movement without tangled hoses and cords. Ideal for framing or remodeling; drives common bulk nails in confined areas and nails metal connectors or joist hangars. Magnetic nose with recessed nail slot holds nails stable for accurate fastener placement. Hardened steel nose . Specs: 70 to 100 PSI;  1/4" NPT; Height: 5-1/4"; Length: 4-1/8" ; Width: -1/2";  Weight: 2.9 lbs. Includes: Impact Nailer with Standard Nose; Finish Nail Nose; Large Bore Nose; Leather Comfort Glove; Nose Wrench; Hex Wrench; Tool Lubricant and Spare O-Rings.
Ingersoll-Rand Edge 236G Air Impact Wrench Ingersoll-Rand EC112  Air Drills Ingersoll-Rand Edge 7811G Reversible Air Drill
Variable reversible speed with aluminum housing, a working torque of 25-200 (ft.-lb.) and a max. torque of 450 (ft.-lbs.), ergonomic grip and handle exhaust. Specs: drive is 1/2" (square), no load speed is 8,000 RPM, average air consumption (CFM) is 4.3, CFM at Load 24, inlet size is 1/4", min. hose size is 3/8", noise level is 90.3 db, weighs (lbs.) 5.3 lbs and is 7 1/8" long. The Ingersoll Rand Edge 1/2" air drill features a powerful and quiet design with speeds from 500 rpm and 0.5 HP. Keyless 1/2" chuck for extended life and easy bit change out. Side ergonomic grip handle and ergonomic grip make this tool more comfortable and precise when getting work done. Contoured grip and trigger. Keyless chuck for quick bit replacement. Handle exhaust directs air away from work area. Specs: 5 HP, 3/8" chuck, 1700 rpm, 4 CFM, 29 CFM at air consumption at load, 1/4" inlet, 3/8" minimum hose size. 7.4" overall length. 2.7 lbs. tool weight.
Ingersoll-Rand 107XPA Air Ratchet Wrenches Ingersoll-Rand 231G Air Impact Wrench Ingersoll-Rand 231C Air Impact Wrench
Features variable speed reverse lever-style throttle, with 160 RPM, 54 ft-lb (73 Nm) of maximum torque, and a 360 degree adjustable exhaust that directs air away from the operator and the work. Specs: average air consumption (CFM) is 4, CFM at load 19, inlet size is 1/4", and min. hose size is 5/16". Twin Hammer impact mechanism and forward/reverse power regulator. Comfortable vibration-absorbing grip. Specs: 6-vane motor, 1/2", 8,000 RPM, 500 ft/lbs.max torque, 5 CFM at 90 PSI. Continuously refined. Offers the sheer power  and performance features to tackle the toughest jobs with ease. Durable and economical. Adjustable power regulator. Pressure feed lubrication. Easy to service two piece construction. 600 ft./lbs of torque and provides 8,000 rpm (1,2000bpm) to deliver fast, efficient performance. Contoured handle for comfort and control.
Universal Tool UT2147R-1 1/2 Inch Pistol Impact Wrench Ingersoll-Rand 1077XPA Air Ratchet Wrenches Mintcraft ATA-055 Quick Coupler
Universal Tool UT2147R-1 1/2 Inch Pistol Impact Wrench
List Price: $189.99
Our Price: $135.45
Savings: $54.54
Variable speed lever style throttle. Advanced head design for extra durability. Up to 54 ft-lbs. torque. Specs: 160 RPM free speed, 3/8" bolt cap, 4 CFM, 19 CFM at load, 94.4/105.4 dBA, 1/4" air inlet. All brass.
Ingersoll-Rand 2100G Composite Air Impact Wrench Ingersoll-Rand EB2125X Air Impact Wrench Plews 545HR-RET Reel Air Hose
Powerful, 550 ft-lbs of max reverse torque. 6-vane motor with forward power regulator, composite housing, handle exhuast, 360 degree swivel inlet, and twin hammer impact mechanism. Specs: no load speed is 9,500 RPM, average air consumption (CFM) is 5, CFM at load 25, 1,200 IPM, inlet size is 1/4", min. hose size is 3/8", noise level is 96.6 db and weighs 4.3 lbs. 690 ft.-lbs. of reverse torque means you'll have the power to burst through those stubborn bolts. Comfortable and easy to use. One hand forward/reverse switch. Lightweight at only 4.2 lbs. Made in the U.S.A. Features all-steel construction and a spring tension brake to prevent accidental unwinding. Mounts in either direction. Polyurethane with dual output fittings. 200 PSI working pressure.
Mintcraft ATA-056 Quick Coupler Ingersoll-Rand 212 General Duty Air Impact Wrench Ingersoll-Rand Edge Pro 2317G Air Impact Wrench Kit
All brass. Powerful 3/8" pistol grip drive impact wrench. 180 ft-lb maximum torque. Consistent torque, even with air pressure changes. More torqe with less vibration. Lightweight and compact. Built-in power regulator helps control torque. Jumbo hammer impact mechanism. Pressure feed lubrication system. Variable speed trigger, twin hammer impact mechanism, ergonomic grip, powerful 6-vane motor and easy to use forward/reverse power regulator. Includes: 1/2" impact tool 231G, 3/8" ratchet 170G, a socket set, and a blow-molded carrying case.
Florida Pneumatic FP-712 Air Buzz Saw Vibration Dampened Stinger 136010 Pneumatic Cap Stapler Ingersoll-Rand 2115TIMAX Industrial Duty Air Impact Wrench

Vibration Damped Reciprocation Saw

For residential roofing and sidewall applications. Allows greater access to tight spaces, while the minimal weight (2-1/2 lbs) reduce operator fatigue. Hard coat anodized end plate stands up to tough jobs. 4 position power regulator dial for max control. Improved grease fitting for easy maintenance. One hand forward/reverse for easy operation with 300 ft-lbs max power. 7-vane motor for more power. Ergonomic housing offers greater operator comfort. Feather touch trigger enables impressive control. Optimized air flow ensures maximum performance. Quiet tool technology reduces sound levels without compromising power performance.
CAP STAPLER 18GA GLUE COLLATE Ingersoll-Rand 3445MAX Pneumatic Angle Grinder FLOORING NAILER 2 IN 1
FLOORING NAILER 2 IN 1
Our Price: $252.52
Designed to secure felt, house wrap and thin foam. Selectable trigger for easy change between sequential and contact modes. Rear exhaust helps keep contaminates away from work. Uses wide 5/16" crown SL style staples that help prevent puncture to the Dewalt cap. Tool-free depth of drive adjustment for precise setting of fasteners. Oil-free design for low maintenance operation. Low nail lockout prevents firing. Belt/rafter hook included. Dry fire lockout. Tool weighs only 5.4 lbs. Operating pressure 70-120 psi. Collation type: glue. Lightweight design with composite grip for improved comfort. Locking lever with tease throttle and rear exhaust. Side handle can be used on left or right. Specs: 0.88 HP, 4-1/2", 12,000 RPM, 5/8" -11 thread, 4-1/2" disc capacity, 10 CFM, 41 CFM at load, 3/8" min hose, 1/4" inlet. Drives 15.5 gauge staples and 16 gauge "L" Cleat nails from 1-1/2" to 2" length. Non-marring, interchangeable base plates for 1/2" (12.7 mm) through 3/4" (19.1 mm) flooring. Ergonomically designed with longer handle and comfortable rubber grip. Lower CFM requirements at 3.7 SCFM. Mallet actuated pneumatic driving action. Lightweight at only 10.85 lbs. Includes Mallet, oil, wrenches, 1/4" (6.4 mm) air fitting with dust cover.
Stanley SL1838BC Cap Stapler Kit ThunderGun 232TGSL Air Impact Wrench Senco SHF200 RW Strip Floor Nailer
Adjustable depth of drive with internal air filter, belt hook, selectable trigger operation converts from sequential to contact operation. Specs: 170 in/lbs driving power, magazine capacity is 160 staples, weighs 3.9 lbs. Uses: 18 ga, 5/16" crown, 1/2"-1-1/2" long staples. Includes: stapler, 1/4" swivel air fitting, 1,000 1" SL Staples, 1,000 Bostitch caps. As close as you can get to the real racing tools. Delivers power, speed, and durability for shop tasks. Specs: 625 ft.-lbs. of torque in reverse, with 10,000 rpm. Pneumatic mallet actuated hardwood flooring cleat nailer for installation of 1/2"-3/4" (12-19mm) hardwood and laminate flooring. Easy on the arm the pneumatic action requires a single strike to drive faster. Non-marring base that adjust between 1/2" and 3/4" flooring without the use of tools. Lightweight and well balanced. Safety trigger prevents accidental ejection of fasteners. Extra long ergonomic handle reduces the amount the operator has to bend over. Includes mallet, oil, wrenches and 1/4" air fitting.
Eagle 1577 Air Impact Screwdriver Stanley N66BC-1 Lightweight Cap Nailer WRENCH IMPACT 1/2IN 930FT/LBS
Impact Screwdriver Torque Range 10-65 ft-lb Tool-free 'Dial-A-Depth' adjustment sets nails to desired depths quickly and conveniently. Durable lightweight magnesium. Quick-load magazine. Tool-free adjustable exhaust. Specs: Weight: 5.7 lbs; Driving Power: 500 Inch lbs at 100 PSI; Operating Pressure: 70 - 120 PSI; Thread Fitting Type: 1/4" NPT; Magazine Capacity: 300 Nails & 100 Caps; Fastener Specifications: 1 1/4"-2 1/2" Wire Weld and Plastic Inserted Coil Nails (.080" - .092") Powerful and durable. Provides 1,350 lbs of torque and 930 ft-lbs of max reverse torque powered by Ingersoll Rand's finely tuned twin-hammer impact mechanism. Weighs only 4.6 lbs, providing less weight so you can work harder and faster for longer periods of time.
Stinger 136250 Pneumatic Cap Nailer Master Power MP2264B 1/4 Quick Change Impact Nut Runner ROOF NAILER/CAP STAPLER KIT
Master Power MP2264B 1/4 Quick Change Impact Nut Runner
List Price: $495.00
Our Price: $348.00
Savings: $147.00
For use where nails are required. It shoots plastic caps for residential roofing and sidewall applications. Key features includes tool-free depth adjustment and an integrated switch for sequential/bumpfire capability. Impact Wrench Variable Speed, 1/4 in Drive Size, 1/4 in Inlet, 110 ft-lb Torque, 10000 rpm Max Speed
    Coil Roofing Nailer features lightweight magnesium housing, quick-set adjustable depth and single action side load canister. Cap Stapler is the preferred method of securing felt, house wrap and thin foam and features adjustable drive set depths and selectable trigger operation. Specifications: ROOFKIT2 Brand Bostitch Coil Roofing Nailer Height 10.6", Length 10.5", Width 4.9", Weight 4.9 lbs, Magazine Angle 15 Degree, Magazine Capacity 120 Nails, Operating Pressure 70-120 PSI, Thread Fitting Type 1/4" NPT. Includes: Coil Roofing Nailer, 18 Ga Stapler, 1/4" Swivel Air Fitting, Carry Case, 1,000 1" SL Staples, and 1,000 Bostitch Caps.
    SIO IW38TBP-2Q Ingersoll-Rand 261 Air Impact Wrench Stanley MIIIFN Angled Hardwood Flooring Cleat Nailer
    SIO IW38TBP-2Q
    Our Price: $389.99
    Lightweight and easy to operate with handle exhaust and oil bath lubrication. Full power in reverse. 3-position adjustable power in forward. Integral 360-degree swivel inlet. Specs: 1,100 ft.-lbs. of max torque. 200-900 ft.-lbs. working torque, 1,200 BPM, 5,500 RPM, 9.5 CFM, 38 CFM at load, 98.1/109.1dBA. 12.4 lbs. tool weight. 9" tool length. For solid and engineered hardwood flooring. High-speed mallet actuated pneumatic operation. Extra-wide composite base plate for added stability. Long reach handle for improved comfort and control. Specs: Height: 11.5"; Length: 17.25"; Width: 3.13"; Weight: 11.2 lbs; Driving Power: 420 Inch Lbs; Operating Pressure: 70-90 PSI; Thread Fitting Type: 3/8" NPT; Magazine Capacity: 110 Cleats. Fastener Specifications: Drives 1-1/2 to 2" Cleat Nails. Includes: Nailer; Graphite Mallet; Pre-Finished Flooring Adapter Foot; Base Plates: 1/2" & 3/4".
    Ingersoll-Rand 2145QIMAX Air Impact Wrench Ingersoll-Rand 285B-6 General Duty Air Impact Wrench Sioux Tools 3T1630 3/8" 1hp 2650rpm Sioux Tools T-handle Drill
    Sioux Tools 3T1630 3/8" 1hp 2650rpm Sioux Tools T-handle Drill
    List Price: $1,199.00
    Our Price: $789.99
    Savings: $409.01
    Delivers incredible performance and industrial grade durability in an impact wrench. Efficient air consumption to save you money. 1,350 ft-lb max reverse torque is compact to access tight spaces. Built to last and designed to withstand tough use in rugged environments. Easy to clean inlet screen means less downtime and better tool performance. Combines power, control and durability. Delivers 1,770 ft-lb (2,400 Nm) of maximum torque, with a 5,250 rpm free speed at 120 psi (8.3 bar) and features a high efficiency 6-vane motor. The integral 360 degree swivel inlet makes kinked hoses a thing of the past. The swept-back handle provides ideal maneuverability, with an available 6" extended anvil for even more accessibility. Improved feather touch trigger. Air Drill/Driver Non Reversible, T-Handle, Chuck Size 10 mm, 3/8 in, Horsepower 1.0 hp, 2650 rpm Maximum Speed
       
     
    1