Home > POWER TOOLS & ACC > PNEUMATIC TOOLS & ACCESSORIES > COMPRESSORS & ACCESSORIES
Choose a sub category:
AIR COMPRESSORS AIR TOOLS AIR TOOL ACCESSORIES
AIR COMPRESSOR HOSES AIR COMPRESSOR HOSE FITTINGS BLOW GUNS
AIR COMPRESSOR ACCESSORIES SPRAY GUNS AIR TANKS
Sort By:
1
Tru-Flate 21-133 Air Hose Fitting Stanley THREADTAPE Thread Sealant Tape Tru-Flate 21-595 Hose Adapter with Ball Socket
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. Properly seals all male threaded connections to prevent air leaks. All brass, corrosion resistant material. Connects FPT to FPT. With ball socket.
Tru-Flate 21-535 Air Hose Bushing Tru-Flate 12-225 Air Line Plug Tru-Flate 12-125 Hose Plug
All brass, corrosion resistant material. Allows user to adjust thread sizes from 1/4" NPT through 3/8" NPT with either male or female ends. Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Tru-Flate 12-235 Air Line Plug Tru-Flate 12-325 Air Line Plug Tru-Flate 21-423 Barb Hose Splicer
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Intended for compressed airlines only. 300 PSI maximum rated working pressure. All brass construction resists rust and will not corrode as easily as other materials.  Precision machined to high quality standards.  Use with hose clamp or ferrules.
Tru-Flate 12-135 Air Line Nipple Tru-Flate 12-335 Air Line Plug Tru-Flate 21-123 Air Hose Fitting
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Intended for compressed airlines only. 300 PSI maximum rated working pressure. All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
Tru-Flate 21-222 Air Hose Fitting Tru-Flate 21-143 Air Hose Fitting Tru-Flate 21-505 Air Line Coupling
All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. Pipe couplings,thread adapters and bushings allows user to adjust thread sizes from 1/8" NPT through 1/2" NPT with either male or female ends. Corrosion resistant material. Connects FPT to FPT.
Stanley TIRE-14F Tire Chuck Tru-Flate 12-435 Air Line Plug Tru-Flate 21-147 Air Hose Fitting
Plated steel; corrosion resistant steel for long life. Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. Intended for compressed air lines only. 300 PSI maximum rated working pressure. All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules.
Tru-Flate 12-527 Air Line Plug Tru-Flate 21-242 Air Hose Fitting Stanley 38M-14M Hex Reducer Nipple
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. All brass, resists rust and will not corrode as easily as other materials. Precision machined to high quality standards. Use with hose clamp or ferrules. Connects FPT to FPT. Use thread sealant tape on all male threads for air tight connections.
Tru-Flate 12-605 Air Line Plug Tru-Flate 21-515 Air Line Coupling Plews 21-557 Drain Cock
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Pipe coupling allows user to adjust thread sizes from 1/8" NPT through 1/2" NPT with either male or female ends. Corrosion resistant material. Connects MPT to MPT. For use in low pressure applications. Hand tightening provides leak-proof metal to metal seal. Corrosion resistant brass.
Plews/Edelmann 12-227/6  Air Compressor Hose Fittings Tru-Flate 17-351 Ball Foot Direct Air Line Chuck Tru-Flate 17-369 Ball Foot Direct Air Line Chuck
Plug 1/4". I/M x 3/8" MNPT. Has a built-in shut-off valve and therefore cannot be used on inflator gauges.  Use when air supply lines come directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks. Has a built in shut off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line.
Tru-Flate 17-361 Ball Foot Direct Combination Air Line Chuck Tru-Flate 12-425 Air Line Plug Tru-Flate 21-467 Barb Hose Splicer
Combination No. 17-350 chuck with 1/4" ID hose barb No. 21-123. Has a built-in shut-off valve and therefore cannot be used on inflator gauges.  Use when air supply lines comes directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks. Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. Intended for compressed air lines only. 300 PSI maximum rated working pressure. All brass construction resists rust and will not corrode as easily as other materials.  Precision machined to high quality standards.  Use with hose clamp or ferrules.
Pro-Fit 0065138 Interior Sinker Nail Senco PC0101 Air Tool Oil Tru-Flate 12-603 Air Line Plug
Pro-Fit Sinker Nail, Interior, Pro-Fit, 6D, 0.12 in Shank Diameter, 1-7/8 in Length, 15/64 in Head, 13 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Premium-grade oil formulated with high-quality paraffin distillate stocks. Contains carefully balanced rust and oxidation inhibitors. Lubricates Pneumatic tools, protects against corrosion and extends part life. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Pro-Fit 0065158 Interior Sinker Nail Pro-Fit 0065198 Interior Sinker Nail Pro-Fit 0065208 Interior Sinker Nail
Pro-Fit Sinker Nail, Interior, Pro-Fit, 8D, 0.134 in Shank Diameter, 2-3/8 in Length, 17/64 in Head, 11-1/2 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Pro-Fit Sinker Nail, Interior, Pro-Fit, 16D, 0.165 in Shank Diameter, 3-1/4 in Length, 11/32 in Head, 9 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Pro-Fit Sinker Nail, Interior, Pro-Fit, 20D, 13/64 in Shank Diameter, 3-3/4 in Length, 3/8 in Head, 7 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power
Pro-Fit 0065178 Interior Sinker Nail Pro-Fit 0065188 Interior Sinker Nail Plews/Edelmann 12-611  Air Compressor Hose Fittings
Pro-Fit Sinker Nail, Interior, Pro-Fit, 10D, 0.148 in Shank Diameter, 2-7/8 in Length, 9/32 in Head, 11 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Pro-Fit Sinker Nail, Interior, Pro-Fit, 12D, 3-1/8 in Length, 5/16 in Head, 10 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Plug 3/8". TF x 1/4" FNPT.
PLUG 3/8IN TF X 3/8IN FNPT    Pro-Fit 0065098 Interior Sinker Nail Pro-Fit 0132098 Exterior Roofing Nail
Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Pro-Fit Sinker Nail, Interior, Pro-Fit, 4D, 7/64 in Shank Diameter, 1-3/8 in Length, 13/64 in Head, 14 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Use for asphalt shingles.
Pro-fit 0132118 Roofing Nail Pro-fit 0132138 Roofing Nail Pro-fit 0132058 Roofing Nail
Use for asphalt shingles. Use for asphalt shingles. Use for asphalt shingles.
Pro-Fit 0132178 Roofing Nail Pro-Fit 0132078 Roofing Nail Pro-Fit 0132158 Roofing Nail
Use for asphalt shingles. Use for asphalt shingles. Use for asphalt shingles.
Pro-fit 0132048 Roofing Nail Stanley AP-38F Auto Hose Adapter Stanley AP-38M Auto Hose Adapter
Use for asphalt shingles. Plated steel construction with drag guard for job site durability and reliability. Large body size for maximum air flow and tool performance. Corrosion resistant steel for long life. Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections.
Stanley AP-14M Auto Hose Adapter 3-IN-ONE 120046 Pneumatic Tool Oil Marvel Mystery MM080R Air Tool Oil With Childproof Cap
Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections. Eight ball coupler design for balanced, strong, secure connections. Marksman spout for easy precision application. Professional grade formula. Lubricates and protects to extend tool life. Quickly removes gum and sludge. Prevents rust. Specially formulated for use in all piston type and rotary air tools, as well as in-line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output.
Stanley-Bostitch BTFP72333  Air Compressor Hose Swivel Plug - Male Blaster 16-ATL Air Tool Lubricant Tru-Flate 12-705 Air Line Plug
Swivel design minimizes hose twisting for improved control. Corrosion-resistant steel. Pre-applied thread connections. Lubricates and protects internal tool parts. Formulated for use with in-line oilers. Removes moisture and provides lubrication. Protects tools against high speeds and shock loads. Use on all pneumatic tools and equipment. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Mintcraft FDQ910 Inflation Kit Pro-Fit 0063198 Casing Nail Pro-Fit 0063178 Casing Nail
Includes: inflation adapter, tapered inflation nozzle, inflation needle, tire nozzle. Use around door and window trim, decks. Use around door and window trim, decks.
Tru-Flate 17-355 Snap Clip On Air Line Chuck Blaster 16-ATC Air Tool Conditioner Stanley IC-14M Industrial Hose Adapter
Snap-On Chuck Clip. Converts any single foot chuck to a clip-on chuck. Fits all standard ball foot chucks with .672-32 thread.  Holds chuck to tire valve while inflating. Cleans and restores pneumatic tool parts. Breaks loose deposits that create friction. Reaches deep into small recesses to leave a protecting film of lubrication. Can be used as in-line lubricant. Removes moisture. An effective antifreeze. Protects tools from freezing down to -25 degreesF. Hardened stainless steel locking balls for maximum performance. Corrosion resistant steel for long life. Pre-applied thread sealant for air tight connections.
Stanley IC-14F Industrial Hose Adapter Stanley-Bostitch BTFP72320  Air Compressor Hose FittingsSeries Coupler Stanley-Bostitch BTFP72321  Air Compressor Hose Coupler
Plated steel construction with drag guard for job site durability and reliability. Six ball coupler design for balanced, strong, secure connections. Corrosion resistant steel for long life. Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball design 1/4 coupler for balanced, strong and secure connections. Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball design 1/4 coupler for balanced, strong and secure connections.
Tru-Flate 13-235 Industrial Air Line Coupler Tru-Flate 13-225 Air Line Coupler Stanley Industrial IHKIT-14F Hose Coupler Kit
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Six hardened stainless steel locking balls for maximum performance. Corrosion resistant steel for long life.
Bostitch BTFP72327 Ball Drain Valve COUPLER UNIVERSAL 1/4IN MPT   COUPLER UNIVERSAL 1/4IN FPT
Turn ball type drain valve. 1/4" NPT male thread. Lightweight compact design. Last longer than standard couplers. 1/4" body size, fits Tru-Flate, Industrial/Milton and Aro 1/4" plugs. Lightweight compact design. Last longer than standard couplers. 1/4" body size, fits Tru-Flate, Industrial/Milton and Aro 1/4" plugs.
Stanley HREPAIR-38 Hose Splice Kit Tru-Flate 41-300 Hose Repair Kit Tru-Flate 13-125 Air Line Coupler
Kit Includes: (1) 1/4" MPT x barbed hose splicer for 3/8" hose; (1) barb x barb hose splicer for 3/8" hose & (3) Clamps. Contains all parts necessary to repair a direct air line hose assembly. Each kit contains: (1) Single Foot Air Chuck, 1/4" Female NPT, (1) Male Hose End 1/4" ID hose x 1/4" NPT, (1) Hose Splicer, 1/4" ID hose, (3) Band Style Hose Clamps, fits 3/8" ID hose Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Tru-Flate 17-383 Dual Foot Direct Air Line Chuck Tru-Flate 17-353 Ball Foot Direct Clip On Air Line Chuck Stanley TEE-14F Tee Fitting
Built-in shut-off valve cannot be used on inflator gauges.  Use when air supply lines come directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks.  Extension for hard-to-reach dual wheel valves on tractors, trucks or bus. Combination No. 17-350 chuck with No. 17-355 chuck clip. Has a built-in shut-off valve and therefore cannot be used on inflator gauges.  Use when air supply lines come directly from the compressor with no other valve in the line.  Automatic inflators use direct air line chucks. Stanley Tee Fitting, 1/4 in Nominal, FNPT End, Brass
Marvel Mystery MM85R1 Air Tool Oil With Childproof Cap Tru-Flate 13-135 Air Line Coupler Plews/Edelmann 18-603 Air Blow Guns
Specially formulated for use in all piston type and rotary air tools, as well as in-line air lubricators. Prevents rust formation while providing positive lubrication for smooth starting and longer tool life. Assures maximum performance by dissolving gum and sludge that cut down tool speed and reduce power output. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Adjust from low air to a full volume flow. Recommended air pressure to 150 PSI maximum. Knurled nozzle makes handling easy. Complete with handy pocket clip. Fits all Industrial/Milton Design 1/4" coupler bodies.
Stanley 3WAY-RND 3-Way Round Air Line Manifold Stanley BTFP72330 Safety Blow Gun Plews/Edelmann 18-319 Tru-Flate Air Safety Blow Guns
Splits single air line into three for running multiple air tools. Use 3/8" male threaded inlet fitting for maximum performance. Aluminum. Safety blow gun. Vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast body. Hang up hook and 1/4" NPT female inlet included. Meets OSHA regulation 1001 for 30 PSI "dead head'' pressure. Inlet Pressure - 150 PSI.
Tru-Flate 13-201 Coupler/Plug Set Bostitch Prozhoze Reusable Hose Repair Kit Tru-Flate 13-335 Air Line Coupler
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-225 1/4" Male NPT Plug and  No.13-235 1/4" Female NPT Coupler. Design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Includes 1 mender and 1 threaded end fittings. Simple 3-step process: unscrew, cut and replace. Includes 1mender and 1 threaded end fitting. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Tru-Flate 21-605 Barb Air Line Swivel Plews 4-25E-RET Recoil Air Hose Plews/Edelmann 13-237 Hose Coupling
Eliminates kinked and twisted air line hose by swiveling a full 360 degrees. Use on air lines, tools, and compressor connections to increase flexibility and convenience. 150 PSI maximum working pressure. Retains its self-coiling properties and stores itself when finished. Can be used with all air-powered equipment on the job site and in garages, plants and service stations. Swivel end fittings on one side reduce hose twist. Temperature range: 32-degree F to 120-degree F. 200 PSI. Yellow Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI.
Tru-Flate 13-325 Air Line Coupler Tru Flate 18-143 Clip-On Safety Blow Gun Tru-Flate 41-125 3-Way 3-in-1 Air Line Manifold
Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Converts any standard ball foot tire chucks to a safety blowgun.  Vented nozzle and built-in pressure reduces limit nozzle pressure to a maximum of 30 PSI, with up to 150 PSI inlet pressure.  Conforms to No.1001 OSHA regulation. Epoxy finish. Supply three air tools from one source. Use on air hose end or as permanently fixed bench outlet. No need to disconnect/connect to use different tools. Three 1/4" NPT outlets and single 1/4" NPT inlet makes this a useful shop or bench accessory.
Tru-Flate 13-101 Coupler/Plug Set Tru-Flate 17-373 Grip Tite Direct Air Line Chuck Mintcraft DZA019 Hose Coupler Set
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-125 1/4" Male NPT Plug and No.13-135 1/4" Female NPT Coupler. Recognized by the extremely short pilot. Has the widest metal section between the ball groove and the pilot. The sealing surface on the end of the nipple is wider than other interchanges, resulting in better sealing and longer seal life. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Has a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Automatic inflators use direct air line chucks. Works like a ``quick coupler". Snaps onto any standard tire valve and stays put until released. 3 piece 1/4" MPT quick plug; 1 piece 1/4" FPT quick plug; 1 piece 1/4"NPT quick coupler.
Tru-Flate 13-301 Coupler/Plug Set Pro-Fit 0065205 Interior Sinker Nail Pro-Fit 0065195 Interior Sinker Nail
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-325 1/4" Male NPT Plug and No.13-335 1/4" Female Coupler.  Identified by a 5/16" pilot and nearly round ball groove. Similar appearance to the Industrial Interchange and care must be taken to correctly identify. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Pro-Fit Sinker Nail, Interior, Pro-Fit, 20D, 13/64 in Shank Diameter, 3-3/4 in Length, 3/8 in Head, 7 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Pro-Fit Sinker Nail, Interior, Pro-Fit, 16D, 0.165 in Shank Diameter, 3-1/4 in Length, 11/32 in Head, 9 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power
Pro-Fit 0065155 Interior Sinker Nail Pro-Fit 0065175 Interior Sinker Nail Pro-Fit 0065185 Interior Sinker Nail
Pro-Fit Sinker Nail, Interior, Pro-Fit, 8D, 0.134 in Shank Diameter, 2-3/8 in Length, 17/64 in Head, 11-1/2 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Pro-Fit Sinker Nail, Interior, Pro-Fit, 10D, 0.148 in Shank Diameter, 2-7/8 in Length, 9/32 in Head, 11 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power Pro-Fit Sinker Nail, Interior, Pro-Fit, 12D, 3-1/8 in Length, 5/16 in Head, 10 ga, Smooth Shank, Vinyl Coated, For General Framing, Coated to Increase Holding Power
Pro-Fit 0065135 Sinker Nail Mintcraft CC970 Air Blow Gun Stanley-Bostitch BTFP72318  Air Compressor Hose Fittings Plug - Male
Pro-Fit Sinker Nail, 6D, 1-7/8 in Length, 15/64 in Head, 13 ga, Vinyl Coated, For General Framing, Coated to Increase Holding Power Die-cast body. 1/4" air inlet. Pre-applied sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections.
Stanley-Bostitch BTFP72319  Air Compressor Hose Fittings Plug - Female Stanley UC38-14F Push-to-Connect Auto Hose Adapter Stanley UC38-14M Push-to-Connect Auto Hose Adapter
Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections. Accepts 3/8" series Industrial Interchange or 3/8" Automotive Interchange plugs. Eight Hardened stainless steel locking balls for maximum performance. Accepts 3/8" series Industrial Interchange or 3/8" Automotive Interchange plugs. Eight Hardened stainless steel locking balls for maximum performance.
Tru-Flate 21-707 Safety Valve Tru-Flate 13-435 Air Line Coupler Tru-Flate 13-425 Air Line Coupler
Brass safety valves constructed to asme standards. Interchangeable with all other asme valves of the same size and pressure. 125 PSI. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Available in sleeve type only. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Available in sleeve type only.
Tru-Flate 13-537 Air Line Coupler Plews/Edelmann 13-603 Hose Coupling Tru-Flate 13-203 Coupler/Plug Kit
Couplers are intended for use on compressed air lines only. All have maximum rated working pressure of 300 PSI. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. (1) One Each:  1/4" FPT Coupler (13-235), 1/4" MPT Coupling (21-505), 1/4" MPT Plug (12-225) and 1/4" FPT Plug (12-235).
Plews/Edelmann 13-605 Hose Coupling Tru Flate 18-233 Safety Blow Gun Plews/Edelmann 18-231 Tru-Flate Air Blow Guns
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Increased performance and yet still meets OSHA regulation 100-1 for 30 PSI 'dead head' pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast body. Complete with hang-up hook and 1/4" NPT female inlet. Inlet pressure 150 PSI. Conforms to all Federal requirements related to OSHA, including noise level regulations. Tamper proof pressure reducers built into this gun limit nozzle pressure to 30 PSI or less when used with listed inlet pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast, epoxy finish body. Complete with hang-up hook and 1/4" female NPT inlet.
Plews/Edelmann 18-302 Tru-Flate Air Safety Blow Guns Tru Flate 18-207 Standard Blow Gun Bostitch Prozhoze Reusable Hose Repair Kit
Meets OSHA regulation 100-1 for 30 PSI "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy duty die cast body with hang-up hook, 1/4" NPT female inlet, and 4" extension. Oil resistant, soft replaceable rubber tip. Will not mar delicate surfaces. Ideal for leak proof seal against oil passages, fuel lines and carburetors when air pressure is needed for cleaning. Allows full line pressure to be used. Includes 1/4" female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI. Includes 1 mender and 1 threaded end fittings. Simple 3-step process: unscrew, cut and replace. Includes 1mender and 1 threaded end fitting.
Pro-Fit 0065095 Sinker Nail Tru-Flate 13-613 Air Line Coupler Tru-Flate 13-611 Air Line Coupler
Pro-Fit Sinker Nail, 4D, 1-3/8 in Length, 13/64 in Head, 14 ga, Vinyl Coated, For General Framing, Coated to Increase Holding Power Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure.
Plews 576-25A Air Hose Tru-Flate 13-527 Air Coupler Plews 4-50E-RET Recoil Air Hose
Orange glo, long life engineered composition PVC hose. Spiral reinforced hose for durability. Nonconductive and oil and abrasion resistant; 1/4" NPT brass fittings on both ends. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Retains its self-coiling properties and stores itself when finished. Can be used with all air-powered equipment on the job site and in garages, plants and service stations. Swivel end fittings on one side reduce hose twist. Temperature range: 32-degree F to 120-degree F. 200 PSI. Yellow
Tru-Flate 13-401 Coupler/Plug Set HOSE AIR POLY BLUE 1/4INX25FT Tru Flate 18-203 Standard Blow Gun
Intended for compressed air lines only. 300 PSI maximum rated working pressure. Includes one each: No.12-425 1/4" Male NPT Plug.  Most easily recognized design. Distinctive, long 3/4" pilot can not be confused with any other designs. No.13-435 1/4" Female Coupler - Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI. Comfortable thumb lever valve control with handy hanger in lever and hanger hook. Compact one piece nozzle. Allows full line pressure to be used. Includes 1/4" female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI.
Tru-Flate 12-537 Air Hose Plug Tru-Flate 24-801 Air Line Pressure Gauge Pro-Fit 0132155 Roofing Nail
Nipple design is considered the industrial standard. Identified by the 3/16" pilot and flat bottom V-shaped ball groove. Intended for compressed air lines only. 300 PSI maximum rated pressure. PSI 0-200  0-14 kg/cm2; mounting back. Use for asphalt shingles.
Pro-Fit 0132175 Roofing Nail Pro-Fit 0132045 Exterior Roofing Nail Pro-Fit 0132055 Exterior Roofing Nail
Use for asphalt shingles. Use for asphalt shingles. Use for asphalt shingles.
Pro-Fit 0132075 Exterior Roofing Nail Pro-Fit 0132095 Exterior Roofing Nail Pro-Fit 0132115 Exterior Roofing Nail
Use for asphalt shingles. Use for asphalt shingles. Use for asphalt shingles.
Pro-Fit 0132135 Exterior Roofing Nail Plews/Edelmann 18-241 Air Blow Gun Kits BLOWGUN SET 2PC
BLOWGUN SET 2PC
Our Price: $16.25
Use for asphalt shingles. Interchangeable nozzles for cleaning and inflating. Complies with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI. Includes: standard nozzle, tapered inflator nozzle and ball inflator nozzle. Light-weight aluminum body with OSHA compliant safety nozzle. 40 CFM
Plews 554-50A-10 Air Hose COUPLER-PLUG SET 4PC          Nati 9389 Air Hose 50 ft
COUPLER-PLUG SET 4PC
Our Price: $16.36
Quality  multi-purpose air hose. Light weight, flexible, kink-resistant design. 300 PSI. Hi Flo Couplers and Plugs increase air flow to ensure tools will provide maximum torque and optimal performance. Push-to-connect design is made of light-weight T6 aluminum. Includes (1) Female Coupler, (1) Female Plug and (2) Male Plugs. Self storing design springs back into coiled shape. Rugged oil and abrasion resistant polyurethane construction. Leak resistant, 360 degree swivel brass end connectors. Spring bend restrictors prevent kinks near hose end. 1/4" NPT; maximum working pressure at 100 psi.
Tru-Flate 13-713 Air Line Coupler Bostitch BTFP72326 Mini Regulator and Gauge Kit Nati 50059 Air Hose 25 ft
Utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. Protective collar guards against accidental disconnect. Due to their large size, do not connect or disconnect if the line pressure exceeds 40 PSI. Intended for compressed air lines only. 300 PSI maximum rated working pressure. Bostitch Regulator and Gauge Kit, Mini, 1/4 in FNPT, 15 gpm, 0 - 160 psi Extremely lightweight and flexible air hose provides ideal performance in all climates. Solid brass fittings: 1/4" - 18 NPT. Oil and abrasion resistant. Heavy duty braided reinforcement. Working temperature range from 30 to 150 degrees F. Maximum working pressure of 250 psi.
Plews/Edelmann 18-221 Tru-Flate Air Blow Guns Pro-Fit 63135 Casing Nail Pro-Fit 063155 Casing Nail
Combination of a blowgun and the siphon spray nozzle. Barbed siphon inlet fits 1/4 inch ID hose or tubing. Use for spray- cleaning engines, applying protective coating, etc. Allows full line pressure to be used. Includes 1/4" female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 PSI. Use around door and window trim, decks. Use around door and window trim, decks.
Pro-Fit 0063195 Casing Nail Plews 41-135 Air Line Regulator with Gauge Plews 576-50A Air Hose
Use around door and window trim, decks. Controls in-line air pressure for paint spray guns or other pneumatic tools. Helps keep air flow at exact operating pressures. Use where precise air flow is desired. Compact, light weight, allows for easy "on the tool" air adjustment. 16psi. NPT thread size is 1/4" on both the male and the female ends. Orange glo, long life engineered composition PVC hose. Spiral reinforced hose for durability. Nonconductive and oil and abrasion resistant; 1/4" NPT brass fittings on both ends.
Mintcraft Tire Inflator Gauge Plews/Edelmann 41-101 Air Tool Oilers HOSE AIR 3/8X50FT
HOSE AIR 3/8X50FT
Our Price: $23.61
Die cast body and dial type gauge with rubber protector. Fitted with single clip-on connector. Air pressure: 0-220 PSI. Air inlet: 1/4'' NPT. Compact oiler that fastens directly to the air tool.  Precisely meters proper amount of oil to the tool only when the tool is in use.  NO adjustments necessary 1/4" male NPT outlet, 1/4" female NPT inlet.  Use on all 3/8" and 1/2" air impact guns, air wrenches, body shop air tools and pneumatic hammers. Ultra Air takes hybrid to a new level, offering increased cold weather flexibility over competitive hoses. When uncoiled, this hose lays flat making it easier to use with no interruption in air flow or tripping hazards. Lighter in weight than rubber and more flexible than PVC; features bend restrictors. Stays flexible, -40 to 150 degrees F. 300 PSI.
Plews 12-50E Poly Air Hose Mintcraft CC910 Air Tool Accessory Kit Prohoze HOPB1450 Air Hose
Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI. Includes: 1 piece tapered brass inflator; 1 piece inflation needle; 2 piece 1/4'' female brass plugs; 4 piece 1/4'' male brass plugs; 1 piece dual tire chuck; 1 piece pencil tire gauge; 1 piece brass blow gun; 1 piece brass safety nozzle. 2 piece male brass hose connectors; 1 piece 1/4" quick brass coupler. 1 piece air blow gun; 1 piece female brass hose connector. All weather flexibility with working temperature range of -40 degrees to 164 degrees F. Heavy duty reinforced braided hose designed with contractor in mind. 300 psi max working pressure with 900 psi burst strength for toughness and safety. End restraints designed for longer hose life.
Tru-Flate 24-343 Manual Mini Air Line Filter Thermoid 522-25 Coupled Air Hose Thermoid 538-25 Coupled Air Hose
Used for all air line applications where efficient filtration is required for wear or failure of pneumatic components. Large filter element surface gives low-pressure drop and long element life. Polycarbonate bowl. Manual drain type. -10 degrees Fahrenheit to +175 degrees Fahrenheit operating temperature range.  20 SCFM, 5 micron element, 1 oz bowl capacity. 3.7" overall height. Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure. Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure.
Mintcraft ATA-052-1 Hose Plug Mintcraft ATA-053-A Hose Plug Sta-Lube SL22133 Air Compressor Oil
High speed steel. Dependable male steel mechanical fitting is perfect for rapidly and securely separating air hoses. Helps promote longer life in all types of reciprocating and rotary compressors. Solvent refined and clay filtered for long lasting, anti-foul operation. Cleans valve seat deposits and extends life.
Plews 576-100A-5 Air Hose Tru-Flate 24-444 Mini Air Line Regulator with Pressure Gauge Stanley Industrial Air Compressor Regulator with Gauge
Orange glo, long life engineered composition PVC hose. Spiral reinforced hose for durability. Nonconductive and oil and abrasion resistant; 1/4" NPT brass fittings on both ends. Employs solid piston and balanced poppet for long lasting performance. Solid piston is impervious to most chemicals and a wide range of lubricating oils and greases. Fast reverse flow capability allows for installation where dual pressures are required. Two gauge ports are provided and a pressure gauge is included. 250 PSI max primary operating pressure and 2 to 125 PSI max secondary operating pressure. 13 SCFM, 2.9" overall height. Stanley Air Compressor Regulator, Industrial, 1/4 in NPTF, Includes: (1) Gauge
REGULATR TOOL AT-HAND INLN AIR North American 7637 Speedway Air Ratchet Wrenches Speedway 50180 Spray Gun
Allows custom pressure settings for various tools or applications. To set required pressure, turn the regulator up to the max 140 PSI and adjust downward to required pressure each time you change the pressure setting. Adjusts while in use. No need to stop working! Specs: Supply Pressure: Minimum 150 PSI, Maximum 400 PSI, Maximum Air Flow: 25 CFM at 125 PSI. 45 ft-lbs torque range. 4 cfm's at 90 psi. Minimum hose diameter is 3/8". Siphon feed type. Required pressure of 50-75 psi. Minimum 3.8" hose diameter.
Plews 12-100E Air Hose Stanley PREMOIL-4OZ Grade Pneumatic Tool Lubricant Prohoze HOPB14100 Air Hose
Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI. Formulated for pneumatic tools. Blended using premium grade turbine oil. Formulated for high speed and temperature conditions. Has anti-wear additives specially formulated for cylinder type applications. Contains rust and oxidation inhibitors to prevent degradation of tool components. All weather flexibility with working temperature range of -40 degrees to 164 degrees F. Heavy duty reinforced braided hose designed with contractor in mind. 300 psi max working pressure with 900 psi burst strength for toughness and safety. End restraints designed for longer hose life.
Senco PC1195 Mini Hand Nailer AIR HOSE PROFLEX 1/4IN X 50FT Abbott Rubber 1502-38X50MM Air Hose 50 ft
Powerful enough to drive bulk nails into joist hangers, hurricane straps, fencing or decking. Fifty percent lighter than traditional palm nailers and is ideal for exceptionally tight spots. Specifications; Reg. Operating Pressure: 60-110 psi (4.-7.6 bar). Air Consumption: 2 - 4 scfm. Length: 2 3/4" (69.9 mm); Width: 2" (55.6 mm). Fastener Specifications: Drives 2" - 3-1/2", 6d to 16d Bulk Nails. Includes Wrench. Tool Oil Required. Aluminum Housing & Rear Exhaust. Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings. Rubber hose, durable, abrasion resistant.
Stanley PREMOIL-20OZ Grade Pneumatic Tool Lubricant Tru-Flate 41-175 Air Compressor Accessory Kit AIR TANK PORTABLE 5 GALLON
Formulated for pneumatic tools. Blended using premium grade turbine oil. Formulated for high speed and temperature conditions. Has anti-wear additives specially formulated for cylinder type applications. Contains rust and oxidation inhibitors to prevent degradation of tool components. Kit contains all accessories needed to connect and use a tank-mounted air compressor. Includes: Couplers/Plugs for air line hose and air tool connections; Air line chuck for filling tire valves; Tire gauge, to check air pressure; Blowgun kit with multiple nozzles for general cleaning, drying, and clearing; Ball and tapered inflator nozzles for inflating toys and recreational equipment. Portable, ready-to-use tank is great for inflating tires and cleaning engines, garage and workshop. Refills from any air service station or air compressor in minutes. Equipped with air shut-off valve, pressure gauge, regulator, 4' x 1/4" air hose and tire chuck 85-125 PSI working pressure. Convenient built-in carry handle.
Plews 13-50AE Air Hose Thermoid 522-50 Coupled Air Hose Ingersoll-Rand EC400-NS  Needle Scaler
Made of braid reinforced blue polyurethane hose. Lightweight and flexible; features bend restrictors. Stays flexible,-30 to 150 degrees F. 300 PSI. Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure. Change your air hammer into a needle scaler with a twist of the arm. It gives you the versatility you need to fly through real work. For use with the Ingersoll Rand 114GQC Air Hammer.
AIR TANK PORTABLE 10 GALLON   Plews 552-50AK-5 Air Hose Kit Edge 3107G Pneumatic Die Grinder
Portable, ready-to-use tank is great for inflating tires and cleaning engines, garage and workshop. Refills from any air service station or air compressor in minutes. Equipped with air shut-off valve, pressure gauge, regulator, 4' x 1/4" air hose and tire chuck 85-125 PSI working pressure. Convenient built-in carry handle. Quality rubber air hose. 300 PSI. Comes with bonus blow gun kit . Use in  garage, shop, industry,  or home. Includes: Safety blow gun, coupler and plugs, 5 different tips. Die grinder features a composite housing for durability and powerful 1/4 HP motor. Specs: RPM: 27,000, Air Inlet Size : 1/4", Min. Hose Size:  3/8", Collet Size (in.): 1/4, Side Handle: No: Durable composite housing Ball bearing construction 1/4 HP motor Self-locking throttle.
Prohoze PRO-1450 Air Hose Stanley PN50 Mini Impact Nailer Tru-Flate 41-907 Air Tank Conversion Kit
Rugged reinforced polyurethane construction is abrasion, puncture and chemical-resistant. Flexible from -40 to 160 degrees F for revolutionary workability. Reusable 1/4" MPT fittings are field repairable in three easy steps. Non-marring translucent material provides a clear view of airline contaminants. Hi-vis safety yellow color for improved jobsite visibility. Snap-fit strain reliefs provide flexible reinforcement for extended life. Up to 2x lighter than standard air hoses. Ribbed design prevents hose from sticking to itself or other jobsite obstructions. Rubber grip designed to insulate and reduce vibration; 360 degree swivel air fitting for maximum accessibility. Front exhaust directs air away from users palm. Fastener Specifications: Drives Most Common Bulk Finish, Framing & Timber Nails. Complies with all new tank standards. Includes: chuck, 4' air hose, pressure gauge, manifold with safety and tank valve.
Tru-Flate 24-404 Compact Air Line Regulator with Pressure Gauge Thermoid 538-50 Coupled Air Hose AIR HOSE PROFLEX 3/8IN X 50FT
Non-rising locking knob. Regulators have a solid piston and balanced poppet for excellent performance and longer life. Impervious to a wide range of lubricating oils, greases, most chemicals, provides accurate control, and assures smooth, uninterrupted operation. Fast reverse flow capacities. Two gauge ports are provided and a pressure gauge is included. Maximum operating pressures are 250 PSI primary and 2 to 125 PSI secondary. Multiple spiral polyester reinforcements. Kink resistant and flexible in extreme temperatures and brass NPT male fittings; 250 pound working pressure. Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings.
Stanley WINTEROIL-20OZ Winter Grade Pneumatic Tool Lubricant Ingersoll-Rand 114GQC Air Hammer Tru-Flate 24-301 Manual Compact Air Line Filter
Prevents moisture coming into the tool from freezing. Medium barrel length with built-in power regulator, professional touch trigger. Designed for exhaust work, cutting  metals, chipping and scraping surfaces. Specs:  Delivers 3,500 BPM., 11/16" bore diameter, 2-5/8" stroke length, 4 CFM, 1/4" air inlet, 3/8" minimum hose size. Includes  chisel shank size .401. Filtration removes airborne solid contaminants which may cause wear or failure of pneumatic components. All filters are complete with filter element and either manual or automatic drains. Maximum operating pressure is 150 PSI at 125 degrees F with polycarbonate bowl. Bowl capacity 5 ounces.
Stanley PRECOMOIL-32OZ Pneumatic Tool Lubricant Tru-Flate 24-311 Manual Air Line Filter Ingersoll-Rand 301B Air Angle Die Grinders
Designed to reduce carbon buildup in compressor valves to ensure a longer compressor life. Provides the proper mix of lubricants for compressors to function properly and efficiently. Filtration removes airborne solid contaminants which may cause wear or failure of pneumatic components. All filters are complete with filter element and either manual or automatic drains. Maximum operating pressure is 150 PSI at 125 degrees F with polycarbonate bowl. Bowl capacity 5 ounces. Lightweight, durable and maneuverable. Comfortable composite grip is ideal for a variety of applications including porting, weld breaking, de-burring, polishing and grinding. Powerful motor delivers 0.33 hp (0.25 kw) and 25,000 rpm free speed. Integral safety lock throttle lever prevents accidental start-up. Tool comes with 1/4" and 6 mm collets and 2 wrenches. Rear exhaust directs air away from the operator.  Built in lubricating wick increases angle gear life. Composite housing protects tool from cold air and offers greater operator comfort. Durable ball bearing construction improves balance, reduces vibration and ensures longer life.
Abbott Rubber 1010-03825-50-4MM Quick Connect Air Hose 50 ft Stanley WINTEROIL-4OZ Winter Grade Pneumatic Tool Lubricant Mintcraft ATA-050 Air Hose Connector
Rubber hose, durable, abrasion resistant. Prevents moisture coming into the tool from freezing. Brass.
Tru-Flate 24-414 Compact Air Line Regulator with Pressure Gauge Mintcraft TA-054 Air Hose End Mintcraft ATA-057 Hose Plug
Polycarbonate locking knob 10.4. Accurate pressure regulation with maximum water and dirt separation are provided in a single, compact unit. The filter significantly increases the life of expensive equipment. The regulator employs a solid piston which  resists rupture, cracking or tearing under pressure or high cycle rates. Tru-Flate Regulators have fast flow capabilities. Maximum operating pressures are: 150 PSI at 125 degrees F primary, 2 to 125 PSI secondary with polycarbonate bowls; N 65 Automatic Float 40 5 oz. Mintcraft Air Hose End, 1/4 in Nominal, MNPT End, 3/8 in Inside Diameter Mintcraft Hose Plug, 1/4 in Nominal, MNPT End, Brass
AIR HOSE PROFLEX 1/4IN X 100FT Mintcraft ATA-0561 Air Line Connector Mintcraft ATA-0243L Barb Hose Splicer
Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings. Brass. All brass.
Edge 3101G Pneumatic Die Grinder Abbott Rubber 1025-0750R-50-CRS 2-Lug Air Hose 50 ft Ingersoll-Rand 170G Air Ratchet Wrenches
Can be used in various applications including porting, weld breaking, deburring, polishing and grinding. Self-locking lever throttle. Grease fitting for increased angle gear life. Ergonomic grip. 20,000 rpm. Rear exhaust. 1/4" collet output. 1.8 m/s2 vibration. 3 CFM average air consumption. 18 CFM air consumption at load. 1/4" air inlet size. Rubber hose, durable, abrasion resistant. Variable speed throttle. Heat treated head for durability. Comfortable ergonomic grip. Ideal for general engine repair, home projects and light industrial applications. Specs:3/8" chuck size, 170 RPM, 55 ft. lbs. max torque, 4 CFM at PSI, 90 max pressure, 3/8" max bolt capacity, 1/4" inlet NPT.
Edge 311G Dual Action Pneumatic Sander Prohoze PRO-14100 Air Hose Senco PC0781 Hand Nailer
Variable speed sander with built-in power regulator, handle control, and 6" pad. Used for body shop and metal or wood preparation. Specs: CFM 4, CFM at Load 17, speed (RPM) 10,000, air inlet size (NPT) 1/4", and min. hose size 3/8". Rugged reinforced polyurethane construction is abrasion, puncture and chemical-resistant. Flexible from -40 to 160 degrees F for revolutionary workability. Reusable 1/4" MPT fittings are field repairable in three easy steps. Non-marring translucent material provides a clear view of airline contaminants. Hi-vis safety yellow color for improved jobsite visibility. Snap-fit strain reliefs provide flexible reinforcement for extended life. Up to 2x lighter than standard air hoses. Ribbed design prevents hose from sticking to itself or other jobsite obstructions. Fits in the palm of the hand, making it ideal for joust hangers, metal straps and pole barn assembly. Leather grip with soft rubber palm pad reduces fatigue. Magnetic nail guide for faster and easier driving. Specifications: 50 - 125 psi (3.5-8.4 bar). Height: 5.8"; Weight: 2.4 lb. Fastener Specifications: Drives Bulk Nails from 5d to 70d. Includes Leather grip.
Ingersoll-Rand 210G Gravity Feed Pneumatic Spray Gun Plews 13-100AE Air Hose