Home > POWER TOOLS & ACC > PNEUMATIC TOOLS & ACCESSORIES > PNEUMATIC NAILERS > PNEUMATIC TOOL ACCESSORIES
Sort By:
1
Senco PC0350 Standard Belt Hook Senco PC0630 Belt Hook Muti 60605X Nailgun Hanger
Fits pneumatic tools with a 1/4'' fitting. Hook nail gun on your tool belt to reduce damage and free up hands. Fits pneumatic tools with 3/8'' fitting. Extra wide width. Hook nail gun to your belt to free up hands to reduce damage. Wide enough to fit over 2x4. Spring loaded and retractable. Solid steel with durable zinc plating. Keeps tools close by. For Use With: Hitachi: NR90AE, NR90AF, NR90AD; Stanley Bostitch: N88RH-2.
Stanley N66C-RK Repair Rebuild Kit Stanley 9B12062R Fuel Cell Stanley TVA6 Trigger Valve Kit
All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced. Special lubricant is provided with every o-ring kit. Rebuild Kit for N66C Model (630.2483). Use this fuel cell with Bostitch, Paslode, and Hitachi Cordless Finish Nailers. Averages 1,100 shots. Contains synthetic lubricants for optimal tool operation. Fits N50, N55, N57, N60, N63, N65, N70, N80, N86, N90; Also N100, 650, 750, 850, 863, T55, T60, RN45, N95RHN. Kit includes: Bostitch TVA6 trigger assembly ,Valve assembly , Lubricant , Two orifice caps. Spring pin punch, Complete instructions.
NAILER PIN 23G PNEUMTIC 120PSI Stanley TVA11 Trigger Valve Stanley F N89ORK O-Ring Kit
Easy quick-load magazine saves time, adjustable exhaust cover directs air away from the user, lightweight design for easy handling, dual trigger safety to minimize the opportunity for accidental fire. Maximum Pressure:120PSI. Replaces worn or broken trigger valve for Stanley Bostitch Nos.N52FN, N62FN, N79RH, N79WW, N80SB, N88WW, N88PC, N90PT, N95RHN nailers. Kit includes: TVA11, Roll Pin., and Lubricant. Contains all o-rings necessary to rebuild the F21, F28, F33, N89C tools. Does not include trigger valve or trigger valve o-rings.
North American 7637 Speedway Air Ratchet Wrenches Stanley ORK13 O-Ring Repair Kit Hitachi 728982 Fuel Cell
45 ft-lbs torque range. 4 cfm's at 90 psi. Minimum hose diameter is 3/8". All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced making a tool in otherwise good condition 'like new'. Special lubricant is provided with every o-ring kit. Contains all o-rings necessary to rebuild the:  RN45. Injects gas into nailer. 1,200 nails per fuel rod. Use with NR90GC (877.4366)  and NR90GR (775.0334) Hitatchi nailers.
Stanley RN46-RK Repair Rebuild Kit NAILER BRAD 18G PNEUMATIC 2IN Ingersoll-Rand EC400-NS  Needle Scaler
All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced. Special lubricant is provided with every o-ring kit. Rebuild kit for No.RN46 (225.1452) . Perfect companion for most small trim and interior molding work. Made of lightweight die-cast aluminum it's easy to handle yet durable enough for heavy duty use. A low nail indicator window lets users know when the magazine is nearing empty. Tool-less jam clearing design for quick jam clearing, rubber non marring tip helps protect work surfaces from damage, contact safety to minimize the opportunity for accidental fire, maximum pressure: 120 PSI. Change your air hammer into a needle scaler with a twist of the arm. It gives you the versatility you need to fly through real work. For use with the Ingersoll Rand 114GQC Air Hammer.
Edge 3107G Pneumatic Die Grinder Stanley ORK11 O-Ring Kit Stanley N88ORK O-Ring Kit
Die grinder features a composite housing for durability and powerful 1/4 HP motor. Specs: RPM: 27,000, Air Inlet Size : 1/4", Min. Hose Size:  3/8", Collet Size (in.): 1/4, Side Handle: No: Durable composite housing Ball bearing construction 1/4 HP motor Self-locking throttle. All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Special lubricant is provided with every o-ring kit. Contains all o-rings necessary to rebuild the:  N80, N90 . Contains all o-rings necessary to rebuild the:  N88 series of tools. Does not include trigger valve or trigger valve o-rings.
Stanley ORK1 O-Ring Kit Ingersoll-Rand 114GQC Air Hammer Ingersoll-Rand 301B Air Angle Die Grinders
All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Special lubricant is provided with every o-ring kit. Contains all o-rings necessary to rebuild the:  T40, T50, N50FN, N60FN. Medium barrel length with built-in power regulator, professional touch trigger. Designed for exhaust work, cutting  metals, chipping and scraping surfaces. Specs:  Delivers 3,500 BPM., 11/16" bore diameter, 2-5/8" stroke length, 4 CFM, 1/4" air inlet, 3/8" minimum hose size. Includes  chisel shank size .401. Lightweight, durable and maneuverable. Comfortable composite grip is ideal for a variety of applications including porting, weld breaking, de-burring, polishing and grinding. Powerful motor delivers 0.33 hp (0.25 kw) and 25,000 rpm free speed. Integral safety lock throttle lever prevents accidental start-up. Tool comes with 1/4" and 6 mm collets and 2 wrenches. Rear exhaust directs air away from the operator.  Built in lubricating wick increases angle gear life. Composite housing protects tool from cold air and offers greater operator comfort. Durable ball bearing construction improves balance, reduces vibration and ensures longer life.
Ingersoll-Rand 317A Hi Speed Sanders Edge 3101G Pneumatic Die Grinder NAILER BRAD PNEUMATIC 18-GAUGE
For small jobs and hard to reach places. Ideal for light sanding, feather edging and rust removal. 18,000 rpm, 0.45 hp (0.35 kw) motor. Easy to handle, compact and lightweight. Built-in power regulator. Can be used in various applications including porting, weld breaking, deburring, polishing and grinding. Self-locking lever throttle. Grease fitting for increased angle gear life. Ergonomic grip. 20,000 rpm. Rear exhaust. 1/4" collet output. 1.8 m/s2 vibration. 3 CFM average air consumption. 18 CFM air consumption at load. 1/4" air inlet size. Tool-free adjustable exhaust cap conveniently directs exhaust away from the user, adjustable depth guide sets nails to desired depths quickly and conveniently, no-mar tip helps to protect work surface. 1/4" air inlet, 100 brad capacity, 5/8" mininum length.9-1/4"L x 2"W x 9-1/2" W
Ingersoll-Rand 170G Air Ratchet Wrenches Edge 311G Dual Action Pneumatic Sander Stanley BT200-RK Repair Rebuild Kit
Variable speed throttle. Heat treated head for durability. Comfortable ergonomic grip. Ideal for general engine repair, home projects and light industrial applications. Specs:3/8" chuck size, 170 RPM, 55 ft. lbs. max torque, 4 CFM at PSI, 90 max pressure, 3/8" max bolt capacity, 1/4" inlet NPT. Variable speed sander with built-in power regulator, handle control, and 6" pad. Used for body shop and metal or wood preparation. Specs: CFM 4, CFM at Load 17, speed (RPM) 10,000, air inlet size (NPT) 1/4", and min. hose size 3/8". All air tool repair kits enable the users to recondition these tools at minimum cost and with little 'down-time'. Simple instructions show how o-rings, seals and bumpers can be replaced. Special lubricant is provided with every o-ring kit.  Rebuild kit for BT200 model.
North American Tool 52710 Speedway Air Compr Ingersoll-Rand EC300  Air Nibbler FinishPro18MG 1U0021N Brad Nailer
1 gallon pancake oil free air compressor with inflation kit. Max psi 100. The Ingersoll Rand Edge 2.0 nibbler offers the ability to cut up to 18 gauge steel, aluminum, plastic or other metals in 6' per minute. Ergonomic grip. Angle head for easy cutting. Low profile throttle lever. 1/4" radius with ideal accuracy gives you the control and cutting power you need without the distorted edges. Magnesium body provides durable  and ultra light tool for comfortable extended use. Oil free motor eliminates oil carryover onto the work surface. Selectable trigger lets you control the fastening method with a flip of the switch. Rotatable rear exhaust and belt hook keeps dust and debris off work surface. Specs: Height: 9.75"; Length: 10.5"; Weight: 2.9 lb; Reg. Operating Pressure: 70-120 psi (4.8-8.3 bar); Mode of Operation: Selectable Actuation. Fastener Specifications: 18 Gauge, 5/8"-2-1/8" Brad Nails. Includes: Case, swivel air plug and wrench.
Stanley BT1855K Lightweight Brad Nailer Kit Edge 300G Random Pneumatic Sander Ingersoll-Rand Edge 236G Air Impact Wrench
Oil-free operation requires no regular maintenance and eliminates the risk of oil stains. Lightweight magnesium design for added durability. Reversible belt hook with integrated pencil sharpener. Selectable trigger system converts from sequential to contact operation. Ultra-quiet rear exhaust, 'Dial-A-Depth' control, low nail lockout,and swivel air fitting with internal filter. Weight: 2.7 lbs; Driving Power: 160 in-lbs.; Magazine Capacity: 110. Fastener Specifications: 18 GA Brads (5/8" to 2-1/8"). Includes: Brad Nailer; 1/4" Swivel Fitting; (1,000)  2" Brads; Carrying Case; Hex Wrench & Belt Hook. Variable Speed. Produces swirl-free finish. Lightweight, low vibration composite design. Contoured grip. Specs: Air Consumption (CFM):16; CFM at Load: 15.5; Speed (RPM): 10,000; Air Inlet Size (NPT): 1/4" ; Min. Hose Size: 5/16". Includes: 360 degree swivel vacuum adapter that provides greater range of movement without tangled hoses and cords. Variable reversible speed with aluminum housing, a working torque of 25-200 (ft.-lb.) and a max. torque of 450 (ft.-lbs.), ergonomic grip and handle exhaust. Specs: drive is 1/2" (square), no load speed is 8,000 RPM, average air consumption (CFM) is 4.3, CFM at Load 24, inlet size is 1/4", min. hose size is 3/8", noise level is 90.3 db, weighs (lbs.) 5.3 lbs and is 7 1/8" long.
Ingersoll-Rand EC112  Air Drills Hitachi NT50AE2 Lightweight Finish Nailer Ingersoll-Rand Edge 7811G Reversible Air Drill
The Ingersoll Rand Edge 1/2" air drill features a powerful and quiet design with speeds from 500 rpm and 0.5 HP. Keyless 1/2" chuck for extended life and easy bit change out. Side ergonomic grip handle and ergonomic grip make this tool more comfortable and precise when getting work done. Extremely lightweight and well balanced. Additional features include a tool-free adjustable depth of drive, selective trigger for sequential or bump fire operation, and reload indicator to prevent dry firing. Specs: Magazine Type: Straight; Nail Capacity: 100; Operating PSI: 70-120; H: 9-3/16" x L: 10" x W: 2-3/8"; Weight: 2.2 lbs. Fastener Specifications: 18 Gauge Brad, Nail Length, 5/8"To 2". Includes: Plastic Carrying Case, Air Fitting, Safety Glasses, Hex Wrenches, & Non-Marring Tip. Contoured grip and trigger. Keyless chuck for quick bit replacement. Handle exhaust directs air away from work area. Specs: 5 HP, 3/8" chuck, 1700 rpm, 4 CFM, 29 CFM at air consumption at load, 1/4" inlet, 3/8" minimum hose size. 7.4" overall length. 2.7 lbs. tool weight.
Smart Point BTFP12233 Corded Strip Brad Nailer Kit Ingersoll-Rand 107XPA Air Ratchet Wrenches North American 7517 Speedway Air Compressors
Drives 18 gauge brad nails from 5/8" to 2-1/8" in length. Oil-free operation reduces the risk of oil stains. Tool-free jam release mechanism for easy nail removal. Dial-A-Depth control for precise countersinking of brad nails. Selectable trigger system for sequential or contact operation. Other features: 1/4" air fitting, rear air exhaust and belt hook with integrated pencil sharpener. Tool weighs only 3.1 lbs. Kit includes: Nailer, 1/4" air fitting, sample brad nails, carrying case and extra no-mar tips. Tool dimensions: 9.5"H x 11.3"L x 3.2"W. Features variable speed reverse lever-style throttle, with 160 RPM, 54 ft-lb (73 Nm) of maximum torque, and a 360 degree adjustable exhaust that directs air away from the operator and the work. Specs: average air consumption (CFM) is 4, CFM at load 19, inlet size is 1/4", and min. hose size is 5/16". 2 gallon oil free air compressor. 1.1 cfm's at 40 psi. Lightweight/portable. Quiet operation, 75dB. Air regulator and quick coupler included. Max psi 100.
Pulsar PCE6020K  Air Compressors BRAD NAILER 18GA PRECIS PNT   Senco PC1010 Air Compressor
Oil-less, 2 gallon tank with 6 piece accessories. 100 psi maximum pressure. 1.5 CFM/40 psi; 120V/60HZ/3 HP. Precision Point technology for precise nail placement as a result of a smaller nose compared to current Dewalt nailers and no need to compress the contact trip to actuate the tool. Long life maintenance-free motor to keep from staining the work surface. Tool-free depth-of-drive adjustment for proper setting of nail heads. Rear exhaust to keep contaminates away from work. Tool free jam release mechanism for easy nail removal. Drives 18 gauge brad nails from 5/8" to 2-1/8" length. Adjustable belt hook allows the tool to be kept near the user. 70-120 psi. Weighs only 11.3 lbs. Kit includes: Nailer, 1/4" swivel fitting, sample brad nails, extra no-mar tips and carrying case. Ultra quiet and ultra light lube-less pump compressor. Ideal for a range of finish and trim projects, as well as for home improvement jobs, hobbies and crafts. Lightweight, portable and easy to maintain. The heavy-duty induction motor is efficient for long life operation. The oil-free pump design and maintenance free. Weighs only 20 lbs.
Porter-Cable C2002 Air Compressor Stanley SB-2IN1 Nailer/Stapler Kit Ingersoll-Rand 231G Air Impact Wrench
Oil-free pump design for reliability and no maintenance. Low amp motor starts easily in cold weather or with extension cord. Upgraded shroud, handle and console cover protect vital components, makes unit easier to carry and includes cord wrap. Two regulated, factory installed air couplers to easily support two users. Water drain valve and rubber feet. Specs: 120 volt, 150 PSI, 3.7 SCFM at 40 PSI and 2.6 SCFM at 90 PSI for fast recovery time. 34 lbs. tool weight. Includes: Compressor and operating manual.. Drives both 18-gauge brads and narrow crown finish staples for ultimate versatility. Adjustable depth guide sets nails to desired depths quickly and conveniently. Tool-free adjustable exhaust conveniently directs exhaust away from the user. Specs: Height: 8.5"; Length: 9.25"; Width: 2"; Weight: 2.6 lbs; Driving Power: 135 Inch Lbs.; Magazine Capacity: 100 Brads or 100 Staples; Operating Pressure: 70-100 PSI; Thread Fitting Type: 1/4" NPT. Fastener Specifications: Range: 5/8" - 1-5/8" 18GA brads, (100)  1/2" to 1-1/2" 18 Gauge Staples. Kit includes: Nailer, 1/4" Air Fitting, 1,000 2" Brad Nails, 1,000 1" Staples, Carrying Case, Hex Wrench, Extra No-Mar Tip and Oil. Twin Hammer impact mechanism and forward/reverse power regulator. Comfortable vibration-absorbing grip. Specs: 6-vane motor, 1/2", 8,000 RPM, 500 ft/lbs.max torque, 5 CFM at 90 PSI.
Ingersoll-Rand 231C Air Impact Wrench FinishPro32 1X0201N Finish Nailer Ingersoll-Rand 1077XPA Air Ratchet Wrenches
Continuously refined. Offers the sheer power  and performance features to tackle the toughest jobs with ease. Durable and economical. Adjustable power regulator. Pressure feed lubrication. Easy to service two piece construction. 600 ft./lbs of torque and provides 8,000 rpm (1,2000bpm) to deliver fast, efficient performance. Contoured handle for comfort and control. Sequential Actuation. Adjustable depth-of-drive and exhaust. Belt hook, full soft grip with no-mar pad and rear bumper. Available in dual action or restrictive fire. Specs: Height: 10.88"; Length: 12.16"; Weight: 4.2 lb; Reg. Operating pressure: 70-120 PSIG (4.8-8.3 bar); Fastener specifications: Gauge: 16; Fastener Range: 1-1/4"- 2-1/2", Finish: Galvanized. Includes Case, Fitting & Oil. Variable speed lever style throttle. Advanced head design for extra durability. Up to 54 ft-lbs. torque. Specs: 160 RPM free speed, 3/8" bolt cap, 4 CFM, 19 CFM at load, 94.4/105.4 dBA, 1/4" air inlet.
Stanley HP118K Headless Pin Nailer Kit Ingersoll-Rand 2100G Composite Air Impact Wrench Senco PC1010N  Air Compressors
Adjustable high/low power control sets pin depth without changing compressor setting. Low profile nosepiece tapers down to contact point. Lightweight, durable aluminum housing. Overmoulded grip. Rear Exhaust. Specs: Weight: 2.5 lbs.; Driving Power: 60 Inch Lbs.; Operating Pressure: 70-120 PSI; Thread Fitting Type 1/4" NPT; Magazine Capacity: 200 Pins. Fastener Specifications: 1/2" to 1 3/16" 23GA Headless Pin Nails. Includes: Pin Nailer; 1/4" Air Fitting; (500 Each): 1/2" Pins, 3/4" Pins, 1" Pins, & Case. Powerful, 550 ft-lbs of max reverse torque. 6-vane motor with forward power regulator, composite housing, handle exhuast, 360 degree swivel inlet, and twin hammer impact mechanism. Specs: no load speed is 9,500 RPM, average air consumption (CFM) is 5, CFM at load 25, 1,200 IPM, inlet size is 1/4", min. hose size is 3/8", noise level is 96.6 db and weighs 4.3 lbs. Designed with the professional contractor in mind. The lightweight and compact design ensure easy portability combined with the ultra quiet operation makes the compressor the ideal finish and trim unit. Long life induction motor and oil free pump design eliminate the need for oil or regular maintenance. Integrated control panel for easy access to couplers and pressure control knob; highly visible gauges. Rugged roll cage protects critical components. 68 dB A for ultra quiet operation. 4 amps at 115 volts. SCFM at 90 PSI 0.7. Maximum pressure 135 psi. Ultra lightweight at only 21 lbs.
COMPRESSOR .75HP 125PSI HOTDOG Stanley FN1664K Lightweight Finish Nailer Kit Stanley-Bostitch BTFP02011 Air Compressors
1.0 CFM at 90 psi. 125 max psi. 0.75 (Peak) horsepower. 44 dB @25 ft. 1 gallon air tank capacity. Dimensions: 14.1"L x 13.77"W x 12.6"H. Weighs 24.7 lbs. Oil-free operation requires no regular maintenance and eliminates the risk of oil stains. Selectable trigger system converts from sequential to contact operation. Low nail lockout prevents dry firing. Swivel air fitting with internal filter, ultra-quiet rear exhaust. Reversible belt hook with integrated pencil sharpener. 'Dial-A-Depth' control for precise countersinking. Lightweight magnesium design for added durability. Quick release nosepiece for fast and easy jam clearing. Specs: Weight 3.9 lbs; Driving Power 285 in-lbs.; Magazine Capacity: 100 Nails; Fastener Specifications: 16GA Finish Nails (1-1/4" to 2-1/2"). Includes: Finish Nailer, 1/4" Swivel Fitting;  (1,000) 2" Finish Nails, 4 Profile Tips, Carrying Case, Hex Wrenches & Belt Hook. 6 gallon oil free Pancake compressor delivers up to 2.6 SCFM at 90 psi. Only 14" in diameter and 33 lbs. for easy portability. It's light enough to carry and get in and out of the jobsite. Long life, maintenance free pump for convenient on going uses. At just 80 dBA, this compressor offers the user a quiet work environment. Integrated control panel helps vital compressor components to be protected against tough jobsite conditions. Includes 2 Universal couplers to easily support 2 users. Ideal for trim and finish applications including installing molding, cabinetry or window/door casings.
Senco PC1130 Air Compressor Ingersoll-Rand EB2125X Air Impact Wrench COMPRESSOR QUITE 135PSI 1 GAL
Slim and quiet oil-splash lubricated compressor. Direct drive motor. Cast Iron Sleeve and head cylinder. Specs: Height: 18.5"; Length: 20.5"; Weight: 39 lb; Recovery Time: 10 seconds; Pump Up Time: 39 seconds; SCFM at (90psi); Horsepower: 1.0 HP Running; Powersource: Electric; Max Pressure: 125 psi; Tank Storage: 2.5 gal.; Max Amp at 115V: 13. Includes: 1/4 Coupler. 690 ft.-lbs. of reverse torque means you'll have the power to burst through those stubborn bolts. Comfortable and easy to use. One hand forward/reverse switch. Lightweight at only 4.2 lbs. Made in the U.S.A. .75 SCFM delivered at 90 PSI, 1.0 gallon tank and 135 max PSI enables more nails to be fired and provides quicker recovery. Durable oil free pump provides extended maintenance-free operation. Low 2.6 amp draw motor provides easy start-up and reduces breaker tripping. Belt drive. Low 71 dBA allows for quieter operation. Roll cage and control panel provide protection to key compressor components. Lightweight at only 24 lbs, thin (9.0") and compact design is easy to carry and store. Ball valve drain allows for quick and thorough tank draining. One quick coupler to easily support 1 nailer. Convenient cord wrap for easy storage. High-flow regulator for increased performance.
FinishPro10 2C0001N Pin Nailer Ingersoll-Rand 212 General Duty Air Impact Wrench Stanley N62FNK-2 Angled Finish Nailer Kit
Extra power for use in hard woods. Durable hardened alloy steel driver with rear exhaust, smooth metal cap and automatically adjusts for different fastener lengths. Easy-open latch for quick and comfortable loading, soft grip handle plus low load alert. Specs: Height: 6-3/4"; Length: 7.87"; Weight: 2.5 lb.; Reg. Operating Pressure: 70-110 psi; Mode of Operation: Sequential Actuation, Magazine Capacity: 126 pins. Fastener Specifications; Gauge: 23; Minimum Length: 1/2", Maximum Length: 1-3/8"; Finish: Galvanized. Includes Case, swivel air plug, wrench and tool oil. Powerful 3/8" pistol grip drive impact wrench. 180 ft-lb maximum torque. Consistent torque, even with air pressure changes. More torqe with less vibration. Lightweight and compact. Built-in power regulator helps control torque. Jumbo hammer impact mechanism. Pressure feed lubrication system. Oil-free operation requires no regular maintenance and eliminates the risk of oil stains. Lightweight magnesium design for added durability. Adjustable depth guide sets nails to desired depths quickly and conveniently. Tool-free removable magazine for fast cleaning and jam clearing. Specs: Height: 11.63"; Length: 140.69"; Width: 3.13"; Weight: 3.8 lbs: Driving Power: 400 Inch Lbs.; Magazine Capacity: 130 Nails; Operating Pressure: 70-120 PSI; Thread Fitting Type: 1/4" NPT. Includes: Finish Nailer; (1,000) 2" Nails; Carrying Case; Hex Wrenches and Four Profile Tips.
North American Tool 52024 Speedway Air Compr Smart Point BTFP71917 Strip Brad Nailer Kit Stanley DA1564K Angled Finish Nailer Kit
2 gallon twin stack, oil free oil compressor with 1/4" x 25' auto rewind hose reel. Construction grade hose. Hose reel provides convenience and on-board storage all in one package. Low profile design for stability and safety. Push connect coupler. Quiet operation, only 75 dB. 1 cfm at 40 psi and .05 cfm at 90 psi. Drives 16 gauge finish nails from 1-1/4" to 2-1/2" length. Oil-free operation reduces the risk of oil stains. Tool-free jam release mechanism for easy nail removal. Dial-A-Depth control for precise countersinking of nails. Selectable trigger system for sequential or contact operation. 1/4" air fitting, rear air exhaust and belt hook with integrated pencil sharpener. Kit includes: Nailer, 1/4" air fitting, sample finish nails, carrying case and extra no-mar tips. Tool weighs only 3.9 lbs. Product dimensions: 11.32"H x 12.5"L x 3.34"W. Uses DA type finish nails. Rear exhaust directs air away from the user. Integrated air blower allows user to clear debris from work-surface. LED work-light for working in closets and dark spaces. Selectable trigger with safety lock-out allows choosing between single and multiple fastener drive mode. 16" OC gauge flips out to measure 16" from end to nose for running baseboard (patent pending). Oil-free operation, dial-a-depth adjustment, tool-free jam release, adjust belt hook, swivel fitting, pencil sharpener and 6 no-mar tips (4 with profiles).
Hitachi NT65M2(S) Lightweight Finish Nailer FinishPro35MG 6G0001N Angled Finish Nailer 6GAL PANCAKE COMPRESS 150PSI
Integrated air duster button allows air from the compressor to clear away dust and debris from the work surface in preparation for the nail. Selective actuation switch lets the user easily select bump fire or sequential fire modes. Tool-less, easy-to-clear nose for quick and simple nail extraction, should a nail jam during use. Depth of drive dial allows the user to easily adjust the drive depth for a professional finish. Specs: Fastener Type16-Gauge Finish; Magazine Angle: Straight; Magazine Capacity: 100; Magazine: LoadingTop; Operating Pressure: 70-120 psi; Jam ClearingTool-Less; Actuation Selective: (Sequential/Bump Fire); Tool Length: 11-5/8"; Tool Width: 2-27/32"; Tool Height:10-7/8"; Tool Weight: 3.7 lbs; GripRubber. Fastener Specifications: Fastener Length Capacity: 1"- 2-1/2";  Fastener Diameter Range: 16-Gauge. Included: Safety Glasses; Tool Fitting; No-Mar Tip; Case. For finish and trim, baseboard, cabinets, caskets, chair rail, decorative trim, door and window casing, furniture trim and paneling. Magnesium main body. Oil-free design, selective actuation, rear exhaust, rotating belt hook and push-button air blower. Tool-free depth-of-drive adjustment. Includes case, swivel plug and wrench. Spec: 70-120 psi reg. operating pressure, 3.2 scfm air consumption (60 cycles per min.), 1/4" NPT air inlet, 110 fastener capacity, 1-1/4 - 2-1/2" fastener range, bright basic, galvanized and stainless finish, 34-degree angle mylar taped strip and weighs 4.2 lb. Includes case, swivel plug and wrench. Oil-free pump design for reliability and no maintenance. Low amp motor starts easily in cold weather or with extension cord. Upgraded shroud, handle and console cover protect vital components, makes unit easier to carry and includes cord wrap. Two regulated, factory installed air couplers to easily support two users. Water drain valve and rubber feet. Specs: 120 volt, 150 PSI, 3.7 SCFM at 40 PSI and 2.6 SCFM at 90 PSI for fast recovery time. 34 lbs. tool weight. Includes 13 Piece accessory kit - 25' x 1/4" PVC air hose wtih coupler and plug assembled, tire chuck with plug, blow gun with plug, tire gauge, blow gun with OSHA saftety nozzle, rubber tip and three inflator adaptors.
Hitachi NT65MA4 Angled Finish Nailer Stanley-Bostitch BTFP01012 Air Compressors FinishPro25XP 760102N Brad Nailer
Integrated air duster button allows air from the compressor to clear away dust and debris from the work surface in preparation for the nail. Selective actuation switch lets the user easily select bump fire or sequential fire modes. Tool-less, easy to clear nose for quick and simple nail extraction should a nail jam during use. Depth of drive adjustment for accurate nail depth in varying materials. Specs; Actuation Selective (Sequential/Bump Fire); Air Consumption: .042(FT3/Cycle at 100psi); LxWxH: 13-17/32" x 3-7/32" x 11-31/32"; Tool Weight: 4.4lbs; Air Inlet 1/4"; Operating Pressure 70-120 psi; Exhaust Deflector:360-Degree Adjustable; Jam Clearing:Tool-Less; Depth Setting:Tool-Less; Magazine Angle: 34-Degrees; Nail Capacity: 100; Magazine Loading: Rear; Fastener Specifications; Fastener Type: 15-Gauge Finish; Fastener Length Capacity: 1-1/4" - 2-1/2"; Fastener Diameter Range: 15-Gauge. Included: Safety Glasses; Case. Rental 2.5 gallon suitcase style compressor. 2.0 SCFM delivered at 90 psi, 150 max psi enables many nails to be fired with quick recovery. Durable oil free pump provides extended maintenance free operation. Low 82 dba allows for quiet operation. Roll cage and control panel provide protection to key compressor components. Bostitch high efficiency/low amp motor for easy start up in cold weather or extension cord application (12 ga 50' (15.2 m) or less). Lightweight (32 lbs), thin (12") and compact design is easy to carry and store. Can be run in either vertical (higher pick-up) or horizontal position (low CG). Ball valve drain allows for quick and thorough tank draining. Two quick couplers to easily support 2 nailers. Bostitch high flow regulator and couplers to maximize nailer performance. Lightweight easy maneuvering and all day work. Comfort and convenient features include: overmold comfort grip, overmold trigger, on-tool power adjustment, 360 degree adjustable exhaust and belt hook. No lubrication required. Specs: Height: 9.9"; Length: 9.8"; Weight: 2.7 lb; Reg. Operating Pressure: 70?120 psig (4.8?8.3 bar); Mode of Operation: Sequential Actuation. Fastener Specifications: Drives Slight & Medium Head 18 Gauge Brads from 5/8" - 2-1/8". Includes Carrying Case.
Pulsar PCE6060K Air Compressors Senco PC1280  Air Compressors Ingersoll-Rand Edge Pro 2317G Air Impact Wrench Kit
120V/60HZ/3.5 Peak HP; 5.2 CFM/40 psi; 4.2 CFM/90 psi. Max. pressure 115 psi. 15 piece accessories included. Designed with the power and speed to handle all finish and trim applications. The compact, lightweight and balanced design allows for easy portability. The oil free pump allows for maintenance free operation and no oil leaks. Draws only 12 amps; will not trip circuit breakers. Integrated control panel for easy access to couplers and pressure control knob; highly visible gauges. Pancake tank design keeps compressor compact and well balanced. Weighs only 38 lbs. Dual couplers allows you to run 2 hoses simultaneously. 150 max psi. Variable speed trigger, twin hammer impact mechanism, ergonomic grip, powerful 6-vane motor and easy to use forward/reverse power regulator. Includes: 1/2" impact tool 231G, 3/8" ratchet 170G, a socket set, and a blow-molded carrying case.
Smart Point BTFP72156 Corded Strip Brad Nailer Kit FinishPro42XP 4G0001N Lightweight Angled Finish Nailer FINISH NAILER 16GA PRECIS PNT
Drives 15 gauge "FN" style angle finish nails from 1-1/4" to 2-1/2" length. Integrated air blower allows tool to clear away debris from work surface. Tool-free jam release mechanism for easy nail removal. Dial-A-Depth control for precise countersinking of nails. 16" On-center gauge flips out to measure exactly 16" from end to nose for installing wall trim. Selectable trigger system for sequential or contact operation. Other features: oil free operation, 1/4" air fitting, rear exhaust and belt hook with integrated pencil sharpener. Kit includes: Nailer, 1/4" air fitting, sample finish nails, carrying case and extra no-mar tips. Tool weighs only 4.32 lbs. Tool dimensions: 12.1"H x 14.3"L x 3.8"W. Lightweight and comfortable magnesium housing. Redesigned with new long life driver, new main body with improved durability, improved trigger ergonomics and reduced trigger reach. Thumb wheel adjustable depth-of-drive, comfort grip and NeverLube technology, no lubrication required. EZ-Clear latch clears jams fast. Two No-Mar pads with onboard storage to protect work materials. 360-degree adjustable exhaust. Construction ruler for quick measurements. Advanced belt hook provides easy and convenient storage. STANDARD EQUIPMENT: 2 no-mar pads, belt hook. SPECIFICATIONS: 15 gauge, Brad head finishing nails, 1-1/4" to 2-1/2" fastener range. Finish: Bright basic, galvanized and stainless. 100 nail capacity. Sequential actuation (restrictive), 70 to 120 psig reg. operating pressure. 11.25" H x 13" L. 4.7 lb. tool weight. Precision Point technology; easy nail placement as a result of a smaller nose compared to current Dewalt nailers and no need to compress the contact trip to actuate the tool. Long life maintenance free motor to keep from staining the work surface. Tool free depth-of-drive adjustment for proper setting of nail heads. Rear exhaust to keep contaminates away from work. Drives straight 16 gauge finish nails from 1-1/4" to 2-1/2" length. Tool-free jam release mechanism for easy nail removal. Selectable trigger: sequential or contact actuation. Adjustable belt hook allows the tool to be kept near the user. 70-120 psi. Straight rear load magazine holds up to100 nails. Weighs only 3.9 lbs. Kit includes: Nailer, 1/4" swivel fitting, sample finish nails, extra no-mar tips and a carrying case.
Senco PC0968 Air Compressor Pulsar PCE6050T Air Compressors Smart Point BTFP72155 Corded Strip Brad Nailer Kit
Cold weather start up valve. Designed with the power and speed to handle all finish & trim applications; comes with an oil less pump which ensures no messy oil leaks. Specs: Height: 13.5" Length: 16"; Weight: 38 lb; Recovery Time: 95 ? 135 psi 17 seconds; Pump Up Time: 0 ? 135 psi 82 seconds; Horsepower: (1.0 HP running); Powersource: Electric; Max Pressure: 135 psi; Tank Storage: 2.5 gal.; Max Amp at 115V: 8 amps. Twin-tank, oil-lubricated 5 gallon unit. Powerful 3.5 HP electric motor, flutter-valve pump puts out 115 max psi and cfm's of 5.2 at 40 psi and 4.2 at 90 psi. Functional enough for use as an inflator, yet vibrant enough for use with the majority of air tools. Compact and portable with easy to read pressure gauges. Drives 15 gauge "DA" style angle finish nails from 1-1/4" to 2-1/2" length. Integrated air blower allows tool to clear away debris from work surface. Tool-free jam release mechanism for easy nail removal. Dial-A-Depth control for precise countersinking of nails. 16" On-center gauge flips out to measure exactly 16" from end to nose for installing wall trim. Selectable trigger system for sequential or contact operation. Other features: oil free operation, 1/4" air fitting, rear exhaust and belt hook with integrated pencil sharpener. Kit includes: Nailer, 1/4" air fitting, sample finish nails, carrying case and extra no-mar tips. Tool weighs only 4.22 lbs. Tool dimensions: 12.1"H x 12.8"L x 3.8"W.
FINISH NAILER 15GA PRECIS PNT COMPRESOR PANCAKE 165 PSI 6GAL FinishPro PC0947 Pneumatic Brad Nailer Compressor Kit
Precision Point technology for precise nail placement due to a smaller nose, compared to current Dewalt nailers and no need to compress the contact trip to actuate the tool. Tool-free jam release mechanism for easy nail removal. Selectable trigger, sequential or contact actuation. 16" on-center gauge flips out to measure exactly 16" from end to nose for installing wall trim. Adjustable belt hook allows the tool to be kept near the user. Long life maintenance free motor helps to keep from staining the work surface. Tool-free depth-of-drive adjustment for proper setting of nail heads. Integrated air blower allows to clear away debris from work surface. Rear exhaust to keep contaminates away from work. Operating pressure 70-120 psi. Lightweight at only 4.2 lbs. No mar pad. Collation type: glue. 165 max psi tank (22.7L) and 2.6 scfm delivered at 90 psi pump, enable long tool run time with quick recovery. High efficiency motor for easy start up in cold weather or extension cord application. (14 gauge or larger, 50 ft (15.2m) or less). 75.5 dBA noise level for a quiet work environment. High flow regulator and couplers to maximize air tool performance. Long life oil free pump for maintenance free operation. Console cover protects controls and is removable to allow easy repair. Outlet tube re-routed to avoid being catch point. 30 lb weight makes unit easy to carry/store. 2 universal couplers to easily support two users. Ball drain valve for quick and thorough tank draining. Convenient cord wrap for easy storage. Protective rubber leg covers to prevent marring. High flow regulator for increased performance. 120 v, 60 Hz, 10 amps, universal motor. Brad nailer has adjustable, depth-of-drive control, exhaust with belt hook, soft grip, no-mar pad and rear bumper. Compressor is easy to carry and to use in a wide variety of applications. Specs: Nailer, 18 gauge; Height: 9.3"; Length: 9.75"; Weight: 3 lb; Reg. Contact Pressure: 70-95 psig (4.8-6.5 bar); Mode of Operation: Sequential Actuation. Fastener Specifications: Drives 18 gauge brad nails from 5/8" to 2". Compressor Height: 13" Length: 14" Width: 10". Weight: 20 lb. Recovery Time: 30 seconds; Pump Up Time: 125 seconds; CFM (90psi): 0.7; Running HP: 0.5 Powersource: Electric; Tank Storage: 1 gallon Max Amp at 115V: 4.
Senco PC1131 Air Compressor Ingersoll-Rand 2115TIMAX Industrial Duty Air Impact Wrench Hitachi EC12 Portable Air Compressor
Generates 4.4 SCFM which provides enough power for all types of applications, from finish to framing. The oil splash design and induction motor provides the durability expected for professional contractors. Direct drive motor, Cast iron sleeve/cast iron head cylinder, oil-splash lubrication. Specs: 2.0 HP Running, 4.4 SCFM at 90 PSI, 125 max PSI, 4.3 gallon tank. 14.5"H x 20.5"L. 60 lbs. tool weight. Includes: 1/4" coupler. Allows greater access to tight spaces, while the minimal weight (2-1/2 lbs) reduce operator fatigue. Hard coat anodized end plate stands up to tough jobs. 4 position power regulator dial for max control. Improved grease fitting for easy maintenance. One hand forward/reverse for easy operation with 300 ft-lbs max power. 7-vane motor for more power. Ergonomic housing offers greater operator comfort. Feather touch trigger enables impressive control. Optimized air flow ensures maximum performance. Quiet tool technology reduces sound levels without compromising power performance. Vertically stacked twin tanks, 2 gallon capacity each for running multiple nailers (4.0cfm at 90psi). Direct drive electric motor provides durability and long life. All metal inner construction and fan. Line regulator with gauge; oil lubricated pump and O-ring on drain cock makes valve easy to open and close. Specs: Power Output: 2hp; Amps: 14.5; Rpm: 3,450; Air Displacement: 4.0cfm at 90psi; Start/Stop Control: 100/125psi; Tank Capacity: 4.0 gal. Weight: 60lbs; Lubrication: Oil; Recovery Time: 14-sec. Includes: Synthetic Oil (8oz) & Oil Dipstick.
Pulsar PCE6150 Air Compressors COMPRESSOR 1.5HP 125PSI STACK North American Tool 52956 Speedway Air Compressors
120V/60HZ/3.5 Peak HP. 5.2 CFM/40 psi; 4.2 CFM/90 psi. Max pressure 115 psi. 2.5 CFM at 90 psi. 1.5 (Peak) horsepower. 125 psi max. 47 dB @25 ft. 4 gallon air tank capacity. Dimensions: 16.93"L x 16.54"W x 16.54"H. Weighs 68.5 lbs. 10 gallon solid cast iron, oil lube air compressor. Duarble steel air intake filter. High efficiency cold start induction motor. Has oversized wheels. 6 cfm at 40 psi and 5 cfm at 90 psi. Max psi 125.
Senco 8M0001N  Pneumatic Finish Nailers COMPRESSOR HANDCARRY 100PSI 4G Ingersoll-Rand 3445MAX Pneumatic Angle Grinder
An industrial strength slight/medium head pinner that fills the gap between 18 gauge brad nails and 23 gauge micro pins. The 21 gauge pins offer significant holding power while leaving a much smaller indent than an 18 gauge brad. Magazine automatically adjusts for different fastener length. Reversible belt hook. Rear exhaust with embedded muffler. Ergonomic handle for comfortable all-day operation. Last nail lockout prevents dry-firing. Ultra-narrow nose allows easy access to mill work and tight corners. On board storage for extra no-mar pad and jam clearing wrench. Use for applying decorative trim, molding, paneling, picture frames, rattan, trim and finish. 1/4" NPT air inlet. Weighs 3.15 lbs (1.43 kg). 8.89"H x 7.87"L x 1.85"W. Fastener capacity: 170. 3.2 CFM delivered at 100 psi pump enables quick recovery. Oil lubricated pump improves durability. Cast iron cylinder enhances pump life. Lightweight  at only 53.32 lbs. design for easy use and handling in a variety of orientations. High-flow regulator for increased performance. Dual soft start valves assist in cold weather start-up. 4 gallon twin stack tank design. Direct drive. 120v Ac 14 amps, 60 Hz, 2 pole induction motor. Pump speed 3,400 rpm. Lightweight design with composite grip for improved comfort. Locking lever with tease throttle and rear exhaust. Side handle can be used on left or right. Specs: 0.88 HP, 4-1/2", 12,000 RPM, 5/8" -11 thread, 4-1/2" disc capacity, 10 CFM, 41 CFM at load, 3/8" min hose, 1/4" inlet.
ThunderGun 232TGSL Air Impact Wrench COMPRESSOR HD 200 PSI 2-1/2GAL North American Tool 7678 Speedway Air Compressors
As close as you can get to the real racing tools. Delivers power, speed, and durability for shop tasks. Specs: 625 ft.-lbs. of torque in reverse, with 10,000 rpm. 3.0 scfm delivered at 90 psi pump. 2.5 gallon tank and 200 max psi enables a large amount of nails to be fired and provides quick recovery. Durable oil free pump provides extended maintenance-free operation. Low 71.5" dBA allows for quieter operation (tested per ISO3744). Low 12 amp draw motor provides easy start-up and reduces breaker tripping. Lightweight (36 lbs.), thin (12.5") and compact design is easy to carry and store. Compressor can be operated/stored in either the vertical or horizontal position. Roll cage and control panel provide protection to key compressor components. Dual quick couplers to easily support 2 nailers. Ball valve drain allows for quick and thorough tank draining. Convenient cord wrap for easy storage. High-flow regulator for increased performance. Drive belt. 120 volt, 60 Hz, 8 amps, universal motor. 2,300 rpm pump speed. 15 gallon vertical, solid cast iron, oil lube air compressor. high efficiency motor with thermal overload protection. 6 cfm's at 40 psi and 5 cfm's at 90 psi. Reduced vibrations with rubber foot stabilizers. Reduced noise level of 93-95 dB. Dual "push connect" manifold. Max psi 125.
Stanley CAP2040ST-OL Air Compressor COMPRESSOR CRDLS 60V 2.5GAL   WRENCH IMPACT 1/2IN 930FT/LBS
Compact design was engineered to be more maneuverable and convenient to carry. It offers enough air flow to operate two framing nailers or three roofing nailers simultaneously. Four oversized rubber feet to help minimize vibration. Durable ball type drain valve. Roll bar handle protects the oil site glass and other gauges against damage if the unit accidentally tips or rolls over. Upgraded industrial-grade pressure switch/regulator makes for easy adjustments and increased durability. Oil-lubricated pump offers a cast iron cylinder for durable performance over extended periods of use.  Specs: 3 horsepower (peak) induction motor, this unit draws only 13.8 amps (120 volts) to prevent circuit breakers from flipping as the motor cuts in and out. Four-gallon stack tank compressor providing 4 CFM at 90 psi and a maximum operating pressure of 135 psi. The FlexVolt 60 volt max 2.5 gallon cordless air compressor offers all of the convenience and portability of cordless with the power of a corded tool. Each battery charge allows for up to 1,220 nails, providing the run-time to complete a variety of applications. OneTurn regulator for fast, accurate pressure adjustments. Heavy duty roll cage for jobsite applications. Brushless motor paired with a heavy duty oil-free pump. 135 max psi tank storage. Lightweight and portable at only 21.5 lbs. and a height of 15.5". Made in the USA. Powerful and durable. Provides 1,350 lbs of torque and 930 ft-lbs of max reverse torque powered by Ingersoll Rand's finely tuned twin-hammer impact mechanism. Weighs only 4.6 lbs, providing less weight so you can work harder and faster for longer periods of time.
Ingersoll-Rand P1IU-A9 Air Compressor Pulsar PCE6280 Air Compressors COMPRESSOR 2HP 125PSI S-STACK
Single stage compressor for professionals and serious do-it-yourselfers it is ideal for the home, shop or jobsite. Specs: HP: 2; CFM at 90 PSI:4.30; Max. PSIG: 135; Dimensions LxHxW: 19x19x19; Net Weight: 77lbs; Start Up Kit: No. 120 V/60HZ/5 Peak Hp. 6.4 CFM/40 psi; 5.6 CFM/90 psi. Max pressure 125. 5.0 CFM at 90 psi. 125 max psi. 2.0 (Peak) horsepower. 49 dB @25 ft. 5 gallon air tank capacity. Dimensions: 28.35"L x 20.08"W x 20.08"H. Weighs 86.3 lbs.
COMPRESSOR WHEEL 200PSI 4-1/2G COMPRESSOR AIR 15GAL 115PSI   COMPRESSOR WORKSHOP 200PSI 15G
200 PSI max tank storage pressure provides a user with 80 percent more usable air. 5.0 SCFM at 90 PSI allows the compressor to recover quickly after its initial tank charge is exhausted. Vertical stand feature and collapsible handle allows a user to save space by transporting or storing the compressor in a vertical position. 78 dBA operation noise level for a quieter work environment. 10" non-flat foam tires allow for easy transportation around the jobsite. EHP efficient high pressure technology allows for longer pump and motor life. Oil free, maintenance free pump for convenient use. Efficient high pressure motor allows the compressor to be run with an extension cord (12 ga. or heavier, 50 ft. or less) due to consistent amp draw requirement of the compressor. High flow coupler allows for maximum nailer performance. Metal console panel provides a display area as well as protects the gauges, couplers and regulator. High flow coupler allows for maximum nailer performance. 2" gauges allow for an easy to read surface. Weighs 83 lbs. 5.2 CFM at 40 PSI or 4.2 CFM at 90 PSI. Max pressure: 115 PSI. Oil lubricated. Features easy to read dual pressure gauges, wheel kit and quick connect coupler. Accessories Kit includes: 1/2" impact wrench, tire inflator with gauge, spray gun, 2" brand nailer/stapler and 25' hose. 5.0 SCFM at 90 psi allows for quick compressor recovery times. 200 psi max tank storage pressure allows for longer air tool run times. 78 dBA (tested per ISO3744) operational noise level for a quieter work environment. EHP efficient high pressure technology delivers exceptional air-tool run times. Oil free, maintenance free pump for convenient use. Efficient high pressure motor allows the compressor to be run with an extension cord (12 ga. or heavier, 50 ft or less) due to consistent amp draw requirements of the compressor. Compact design allows for the compressor to be easily moved, transported and stored. Robust dual purpose handle provides additional protection to the compressor along with serving as a hose wrap. Metal console panel protects the gauge, coupler and regulator. High flow air regulator and high flow coupler allows for maximum air tool run time. 2 inch gauges allow for an easy to read surface. Wide track, semi-pneumatic tires allow for additional stability, easy movement and no tire maintenance. 1,750 rpm pump speed. 120 volts power supply.
Ingersoll-Rand 261 Air Impact Wrench Ingersoll-Rand 2145QIMAX Air Impact Wrench Ingersoll-Rand P1.5IU-A9 Air Compressor
Lightweight and easy to operate with handle exhaust and oil bath lubrication. Full power in reverse. 3-position adjustable power in forward. Integral 360-degree swivel inlet. Specs: 1,100 ft.-lbs. of max torque. 200-900 ft.-lbs. working torque, 1,200 BPM, 5,500 RPM, 9.5 CFM, 38 CFM at load, 98.1/109.1dBA. 12.4 lbs. tool weight. 9" tool length. Delivers incredible performance and industrial grade durability in an impact wrench. Efficient air consumption to save you money. 1,350 ft-lb max reverse torque is compact to access tight spaces. Built to last and designed to withstand tough use in rugged environments. Easy to clean inlet screen means less downtime and better tool performance. Single stage compressor for professionals and serious do-it-yourselfers, the versatile 'Garage Mate ' is ideal for the home, shop or jobsite. Equipped with a pressure switch, pressure gauge, regulator, safety valve, manual drain and six-foot power cord. Features a cast-iron, oil-lubricated pump for solid, reliable performance. Specs: CFM at 90 PSI: 5.2; Max. PSI: 135; HP: 2; Dimensions LxHxW: 22 x 23 x 43; Net Weight: 200lbs;  Voltage/Engine: 115 - 1 - 60
Ingersoll-Rand 285B-6 General Duty Air Impact Wrench North American 53200 Speedway Air Compressors North American Tool 7295 Speedway Air Compressors
Combines power, control and durability. Delivers 1,770 ft-lb (2,400 Nm) of maximum torque, with a 5,250 rpm free speed at 120 psi (8.3 bar) and features a high efficiency 6-vane motor. The integral 360 degree swivel inlet makes kinked hoses a thing of the past. The swept-back handle provides ideal maneuverability, with an available 6" extended anvil for even more accessibility. Improved feather touch trigger. 20 gallon, 2 cylinder, solid cast iron belt drive. Oil lube air compressor with pneumatic tires. 6.6 cfm's at 40 psi and 5.9 cfm's at 90 psi. Max psi 135. OHV high performance ENERGIN gas engine wheelbarrow air compressor. 9 gallon twin tanks with solid cast iron "V" design pump for maximum performance. Run flat tire and dual "push connect" manifold. 9.1 cfm at 90 psi.
IronHorse IHD6160V1 Air Compressor Hitachi EC2510E Air Compressor Ingersoll-Rand SS3J5.5GH-WB Air Compressor
Thermally protected  electric motor with 60 gallon ASME registered tank, easy view oil sight gauge, cast iron compressor  minimizes vibration. Individual and removable cylinders, no magnetic motor starter required, pressure switch has on/off control. High efficiency reed valves for maximum performance, efficient heat removal from pulley-fan, sturdy belt guard. Specs: CFM/PSI is 11.2 CFM at 90 PSI, max rated PSI is 150, 208/230V electric motor, dimensions are: 27"Lx20"Wx65"H, weighs 260 lbs. Solid cast iron cylinder provides industry recognized premium material for long life, consistent compression and low oil carryover. Oversized oil level site glass allows everyone to monitor the oil level for the pump avoiding pump damage due to lock up from inadequate oil supply. Specs: Power Output: 5.5 Net HP at 3,600 RPM ( Actual power output for the engine installed in the final machine will vary depending on numerous factors, including the operating speed of the engine in application, environmental conditions, maintenance, and other variables), Honda engine. Displacement: 196 cc; Tank Capacity: 8 Gallon; Motor RPM: 3,200; CFM: 9.0 at 100 psi; Weight: 144 lbs. Includes: Synthetic Oil; Oil Dipstick; Wheel; Pressure Gauge; Drive Belt; Filter. Lightweight and durable with a low-profile design providing maximum maneuverability on the job site. Cast-iron, oil-lube compressors are designed for the toughest continuous duty applications. Specs:  5.5 HP, Honda engine, 11.8 CFM at 90 PSI, 135 PSI, 1/4" NPT, 8-gallon twin tank. Includes: Pressure switch, regulator and gauge, two quick disconnects to power multiple tools and twin 8-gallon capacity tanks.
Woods/Iron Horse IHD7180V1 Iron Horse Air Compressors North American 51866 Speedway Air Compressors
Features a 3 piston "V" style cast iron pump for longer life. Produces 16.5 CFM at 90 pis with a max pressure of (150 psi). No magnetic starter required. Oil sight glass. Enclosed belt guard. Heavy duty pressure switch. ASME certified tank that meeds the national pressure vessel certifications. Features a commercial grade quality motor with a built in starter. Low rpm (1050) and quiet operation. 5 horse power 230 volt, twin cylinder 2 stage cast iron pumps operates at 10.8 CFM at 150 psi, 12 CFM at 90 psi and 13.1 CFM at 40 psi, with a maximum psi of 150. Oil lubricated, belt driven.
   
 
1