Home > HAND TOOLS > CLAMPS / FASTENING TOOLS > WELDING SUPPLIES > WELDERS
Sort By:
1
Oatey 30710 Acid Brush BRSH FLUX 3/PK 3/8IN          Oatey 53026 Wire Solder
Use for applying liquid or paste fluxes. For liquid or paste soldering flux. 6" (152.4mm) long and 1/2" (12.7mm) wide. 3-pack. Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range.
Oatey 53185 Rosin Core Wire Solder Oatey 53023 Rosin Leaded Core Solder Oatey 53012 Rosin Leaded Core Solder
Alloy of 60 percent Tin and 40 percent Lead; no external flux is needed. 361 degrees F ? 375 degrees F melting range. Can be used for electrical applications including wiring and other fine electronic work. Contains lead. Not for use on drinking water lines. Alloy of 60 percent Tin and 40 percent Lead; no external flux is needed. 361 degrees F ? 375 degrees F melting range. Can be used for electrical applications including wiring and other fine electronic work. Contains lead. Not for use on drinking water lines. 40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F.
Safe-Flo 53061 Wire Solder Weller 7250W Standard Soldering Tip Oatey 53010 Wire Solder
Alloy of tin, silver, copper and bismuth; works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics with a melting range of 420 to 460 degrees F;  .084" diameter. Used for tin plate work, sheet metal seaming, and hot water heating lines. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Made of copper, for Weller soldering guns. Specs: Tip Width O/D .22 in.; Reach/Length 2.57 in. 50 percent tin and 50 percent lead, used with an external flux. Good flow characteristics and low melting point. 361 to 421 degrees Fahrenheit melting range; 0.075" diameter. Used for soldering galvanized gutters, general repairs, radiators, sheet metal and non-drinking water lines. Contains lead, not to be used for plumbing applications.
Oatey 53174 Acid Core Wire Solder Weller 7135N Standard Soldering Tip Weller 7135W Standard Soldering Tip
Lead free alloy of 95 percent Tin and 5 percent Antimony. Acid flux is contained within the core. Used for for sheet metal, radiator, gutter repair work with a melting range of 450 degrees F-464 degrees F; .081" gauge Made of copper, for Weller soldering guns. Specs: Tip O/D  .165 inches; Reach/Length .885 inches. Made of copper, for Weller soldering guns. Specs: Tip Width O/D .165 in.; Reach/Length .885 in.
SLDR 40/60-1/4LB 1/8IN        Oatey 53011 Leaded Acid Core Solder SOLDER 1/8IN SW40TIN/60L 1/4LB
40 percent tin, 60 percent lead. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). NOT FOR ELECTRICAL CONNECTIONS. 40 percent tin and 60 percent lead alloy with acid flux contained in wire core; no external flux necessary. For sheet metal work, auto radiator repair, steel gutters and more. Not for use in electrical applications. 361 to 460 degrees Fahrenheit melting range. 0.081" diameter. Contains lead, NOT for plumbing applications. 40 percent tin, 60 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). NOT SUITABLE FOR ALUMINUM.
CLOTH EMERY 80GRIT 1INX10YARD CLOTH EMERY 120GRIT 1INX10YARD CLOTH EMERY 180GRIT 1INX10YARD
Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll.
CLOTH EMERY 320GRIT 1INX10YARD Oatey 53019 Instant Wire Solder Oatey 53016 Rosin Core Solder
Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Easy to use; solder and flux all in one. Can be used on drinking water lines. Includes acid brush. 40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F.
SOLDER 3/32IN 40TIN/60L 1/4 LB SLDR 50/50 3/32IN 1/4LB       SAND SCREEN 80 GRIT 1-1/2X9FT
40 percent tin, 60 percent lead. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). 50 percent tin and 50 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 5500 PSI. Melting Temp: 421? (216? C). NOT SUITABLE FOR ALUMINUM. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals.
SAND SCREEN 120 GRIT 1-1/2X9FT SAND SCREEN 180 GRIT 1-1/2X9FT SAND SCREEN 320 GRIT 1-1/2X9FT
1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals.
Oatey 53027 Wire Solder SOLDER 1/16IN 60TIN/40L 1/4LB Copper Lock 10-801 No Heat Solder
Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range. 60 percent tin, 40 percent lead. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Tensile Strength: 6900 PSI. Melting Temp: 375? (190? C). Fast, easy, permanent; apply inside the copper connector, fit in the copper pipe and within seconds a permanent leakproof seal will occur.  Pressure may be applied after two minutes; can withstand pressures up to 500 PSI; can withstand temperatures from -60 degrees F to +300  degrees F. Meets US Military specifications. Good with all refrigerants.
SOLDER 1/8IN 95TIN/5ANT 1/4 LB Oatey 53015 Acid Core Wire Solder Safe-Flo 53062 Wire Solder
Tin-antimony "lead-free" solder can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. 40 percent tin-60 percent lead, .125" gauge; can not be used on drinking lines. Alloy of tin, silver, copper and bismuth. Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics with a melting range of 420 to 460 degrees F;  0.117" diameter. Used for tin plate work, sheet metal seaming, and hot water heating lines. Meets requirements of Safe Drinking Water Act for use on copper potable water lines.
Oatey 53176 Acid Core Wire Solder SOLDER COMM 1/8IN 1LB RSN CRE SOLDER 1/8IN AC30TIN/70L 1/2LB
Lead free alloy of 95 percent Tin and 5 percent Antimony. Acid flux is contained within the core. Used for for sheet metal, radiator, gutter repair work with a melting range of 450 degrees F-464 degrees F; .081" gauge Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Melting Temp: 575? (299? C). 30 percent tin, 70 percent lead. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Tensile Strength: 4500 PSI. Melting Temp: 491? (255? C). NOT FOR ELECTRICAL CONNECTIONS.
SOLDER WIRE KITS WATER SOLUBLE Oatey 50193 Acid Core Wire Solder SOLDER COMM ACID CRE 1LB 1/8IN
General uses: solder pipes, brazing metal, plumbing and automotive repairs. Product details: wire melting temperature: 450 degree F; diameter: 0.062"; wire net weight: .75 oz. silver solder; .5 oz. water soluble paste flux - NSF certified to ANSI/NSF61. Kit contents: 3 oz. solid wire solder, 1 oz. water soluble paste flux, 2-1/4" acid brush, abrasive cloth. Alloy of 40 percent Tin and 60 percent Lead. For repairing galvanized gutters, filling metal seams and other general repairs with a melting range of 360 degrees F - 460 degrees F. Can not be used on drinking water lines; .081" gauge. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Melting Temp: 575? (299? C). NOT FOR ELECTRICAL CONNECTIONS.
Oatey 53014 Leaded Wire Solder Oatey 50192 Solid Wire Solder SOLDER 1/8IN SW 50/50 1/2LB
50 percent tin and 50 percent lead; use of flux required; .125" gauge. General purpose solder for sheet metal work, auto radiator repair and steel gutters. Contains lead, NOT for plumbing applications. Alloy of 50 percent tin and 50 percent lead, use with Oatey #5 paste or liquid flux. Used for sheet metal, galvanized gutters, general repairs and non drinking water lines. Not to be used for plumbing. .125" gauge. Contains lead, NOT for plumbing applications. 50 percent tin and 50 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 5500 PSI. Melting Temp: 421? (216? C). NOT SUITABLE FOR ALUMINUM.
Oatey 31400 Flame Protector Safe-Flo 50683 Wire Solder Kit SOLDER 1/8IN LF S-WIRE 1/4 LB
Heat shield to protect studs, walls, floors, and other surfaces from sparks or flame and is ideal to use with propane and MAPP gas torches for applications up to 2500 degrees F. Made with Zoltek Pyron fibers, a non-asbestos flame retardant material. Size: 9" x 12". Alloy of tin, silver, copper and bismuth. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Provides excellent flow and fill characteristics. 420 to 460 degrees Fahrenheit melting range. Includes 8 oz. solid wire solder 0.117" diameter, 1.7 ozs. No.95 lead free tinning flux, acid brush, sand cloth, and how-to instructions. Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C).
Safe Flo H-20-5 50691 Lead Free Flux Solder Kit WIRE WELD ALUM MIG .030IN 1LB Copper Lock 10-800 No Heat Solder
IAPMO Listed solder and water soluble flux NSF-61. Flux meets ASTM B-813 standard and is City of L.A. approved. Lead free silver solder meets ASTM B-32 standard. Kit contains: 8 oz., .117" gauge silver lead free solder, 1.7 Oz. H-20-5 water soluble flux, an applicator brush and a sand cloth. Features 5% magnesium content and a bright finish. It flows freely at 1,180 degrees F (637.8 degrees C) and provides less "bird-nesting" on push-type MIG welders. Applications include diesel engine bases, truck frames, cargo tanks and gun mount bases. Light Grey color coding on label. Required Shielding Gas: Argon. Recommended Polarity: DCEP Reverse. Tensile Strength (PSI): 63,000. Fast, easy, permanent; apply inside the copper connector, fit in the copper pipe and within seconds a permanent leakproof seal will occur.  Pressure may be applied after two minutes; can withstand pressures up to 500 PSI; can withstand temperatures from -60 degrees F to +300  degrees F. Meets US Military specifications. Good with all refrigerants.
Oatey 20019 Wire Solder SOLDER 1/8IN 95TIN/5ANT 1/2 LB Safe-Flo 29024 Wire Solder
Alloy of 50 percent tin and 50 percent lead, use with Oatey #5 paste or liquid flux. Used for sheet metal, galvanized gutters, general repairs and non drinking water lines. Not to be used for plumbing. .125" gauge. Contains lead, NOT for plumbing applications. Tin-antimony "lead-free" solder can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. Alloy of Tin, Copper, Silver, and Bismuth that works much like 50/50 solder. Recommended for use on potable water systems for sweating copper joints. Also effective on stainless steel, brass alloys, chrome alloys, galvanized steel and cast iron piping.  Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics. 420 to 460 degrees F melting range; 0.117" diameter. Meets ASTM standard B-32 and the requirements of Safe Drinking Water Act. Can Not Be Used On Aluminum.
SOLDER 1/8IN LEADFREE SW 1/2LB Oatey 21018 Wire Solder SOLDER 1/8IN50/50 SOLIDWIRE1LB
Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C). Alloy of 40 percent Tin and 60 percent Lead; 361 degrees F-460 degrees F melting range. Commonly used for tin plating, seaming joints, copper DWV systems and sheet metal repair. Contains lead, NOT for plumbing applications. For general purpose use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. NOT SUITABLE FOR ALUMINUM. 5500 PSI Melting Temp: 421degrees (216 degrees C).
KIT SOLDER SILVER SS TUBE     SOLDER 1/8IN COM SOLIDWIRE 1LB Oatey 21305 Bar Solder
Premium high strength acid flux cored silver bearing solder for joining all metals except aluminum, magnesium and zinc die cast. 6% silver content. Stays birght and hard. Nontoxic. Joint strength up to 20,000 PSI tensile strength. Weight: 9 oz. Working temperature: 431? F (221.7? C). Application temperature: 400? F to 700? F (204? C to 371? C). For general purpose use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. NOT SUITABLE FOR ALUMINUM. Melting Temp: 575 degrees (299 degrees C). Alloy of 50 percent Tin and 50 percent Lead; 361 degrees F ? 421 degrees F melting range. For use with copper drain piping, tin plating, seaming joints and sheet metal. Not for use on drinking water lines.
Oatey 53171 Rosin Core Wire Solder Oatey 21212 Rosin Leaded Core Solder Oatey 21115 Leaded Acid Core Solder
Lead free alloy of 95 percent Tin and 5 percent Antimony. 450 degree F ? 464 degree F melting range. Most commonly used where frequent and extreme temperature changes and vibrations occur. Contains lead, NOT for plumbing applications. 40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F. 40 percent tin-60 percent lead, .125" gauge; can not be used on drinking lines.
Oatey 20015 Leaded Core Solder Safe-Flo 29025 Wire Solder SOLDER 1/8IN LEAD FREE SW 1 LB
Alloy of 50 percent tin and 50 percent lead. General purpose solder for sheet metal work, auto radiator repair and steel gutters. Not to be used on drinking water lines. .125" gauge. Contains lead, NOT for plumbing applications. Alloy of Tin, Copper, Silver, and Bismuth that works much like 50/50 solder. Recommended for use on potable water systems for sweating copper joints. Also effective on stainless steel, brass alloys, chrome alloys, galvanized steel and cast iron piping.  Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics. 420 to 460 degrees F melting range; 0.117" diameter. Meets ASTM standard B-32 and the requirements of Safe Drinking Water Act. Can Not Be Used On Aluminum. Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C).
SOLDER 1/8IN 95TIN/5ANT 1 LB  Oatey 22018 Lead Free Plumbing Solder WIRE WELD MILD MIG .024IN 10LB
Tin-antimony, lead free, can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. Tensile Strength: 6000 PSI. Melting Temp: 464? (240? C). Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range. Ideal for auto body repair and fabrication on most ferrous metals. Contains a high level of manganese and silicon for a superior weld, even on rusty, dirty steel. Produces a smooth bead which requires less grinding. Not recommended for aluminum engines. Yellow color coding on label. Required Shielding Gas: Argon/CO2. Recommended Polarity: DCEP Reverse Polarity. Tensile Strength (PSI): 70,000.
WIRE WELD SS MIG .030 IN 2LB  Oatey 30712 Acid Brush WELDER ARC STICK 120VOLT 90AMP
Consists of 20% chromium and 10% nickel. Welds type 301, 302, 304, 308, 321 and 347 stainless steel. Applications include the food and beverage industry, maintenance and repair. Blue color coding on label. Required Shielding Gas: Argon or Argon/CO2. Recommended Polarity: DCEP Reverse. Tensile Strength (PSI): 79,000. Use for applying liquid or paste fluxes. Stick welder/TIG capable (TIG torch not included); welds 16 gauge up to 5/16"; handles up to 1/8" electrode; 120V input, 90A output.
WELDER MIG FLUX CORE 120V 125A WELDING CABLE 1/0GA 50FT REEL WELDER MACHINE MIG FC-I 140
Gasless/flux-core welding only; 120V input, 125A output; welds 24 gauge up to 1/4"; handles .030" wire. Highly flexible cable manufactured with 1,007 strands of fully annealed soft-drawn copper. Uses paper separator between copper and outer EPDM jacket. Will not kink, even in cold weather. Outer jacket has excellent oil, grease, water, flame, tear, cut and abrasion resistance. Rated at 600 volts. Conductor temperature range of -58? F (-50? C) to 221? F (105? C). Meets or exceeds ASTMB-172. 50' (15.24m) reel. Gasless/flux-core welding only. Welds 24-gauge up to 1/4 in. Handles .030 in. wire.
WELDING CABLE 4GA 125FT REEL  WELDING CABLE 2GA 125FT REEL  WELDER MACHINE MP 140
WELDER MACHINE MP 140
Our Price: $370.19
#4 gauge highly flexible welding cable manufactured with 378 strands of fully annealed soft-drawn copper. Uses paper separator between copper and outer EPDM jacket. Will not kink, even in cold weather. Outer jacket has excellent oil, grease, water, flame, tear, cut and abrasion resistance. Rated at 600 volts.Conductor temperature range of -58? F (-50? C) to 221? F (105? C). Meets or exceeds ASTMB-172. #2 gauge highly flexible welding cable manufactured with 636 strands of fully annealed soft-drawn copper. Uses paper separator between copper and outer EPDM jacket. Will not kink, even in cold weather. Outer jacket has excellent oil, grease, water, flame, tear, cut and abrasion resistance. Rated at 600 volts. Conductor temperature range of -58? F (-50? C) to 221? F (105? C). Meets or exceeds ASTMB-172. Multi-Process welder: MIG/DC TIG/Stick welder (TIG torch not included). Welds up to 5/16 in. Uses gasless wire .030/.035 in. Solid wire .024/.030 in. Up to 1/8 in. stick electrode.
WELDER ARC AC/DC230V 180A 57LB WELDER MIG 120V 30-140AMP 57LB WELDER MIG 230V 30-190AMP 63LB
This welder has a duty cycle of 20% @ 230A, 50% @ 150A AC, 20% @ 180A and 35% @ 135A DC; the electroholder cable is 3m 25mm2, the earth clamp cable is 2m 25mm2, both with dense connector. Input cable American Wire Gauge (AWG) 10, 2.5mm. 50A plug. CSA-approved. Cat #00329, wheel & handle kit for "Forney" 00313 & 00314 must be purchased separately. Weight: 116 lbs (52.62Kg). Machine for farming, automotive and small welding repair; it runs off household 115V power and offers a duty cycle of 115A @ 20%, 90A @ 35%, 60A @ 60% and 55A @ 100%; the Euro connect Torch with "Tweco" style consumables makes this machine easy to use; the 8" power cord and 10" MIG gun offers 18 feet of work area; better wire feeding is ensured with our cast aluminum wire drive system and dual geared idler and drive roll with de-spooler; the larger cabinet space allows for easier access to 4" and 8" spools; the improved design offers integrated feet and a torch wrap for cable organization. Specifications: Processes: MIG (GMAW); Flux Cored (FCAW). Input Power: 115V. Amperage Range: 30-140A, DC CV. Wire Diameter Range: .023" - .035". Plate Thickness Range: 24 ga. - 1/4". Weight: 57 lbs. Dimensions: 19" x 9.5" x 16.5". Duty Cycle: 115A, 19.75V @ 20%, 90A, 18.5V @ 35%. Regulator and gas hose; offers a Euro Connect Torch and fast disconnect to swap out torch and clean liner; larger cabinet space allows easy access to 4" (1-2lbs) and 8" (10-11lbs) spools; perfect for farms, automotive and repair welding and permits a 25' working envelope with its 10' torch and 15' power cord; the wire feeding is smooth and consistent as this welder has a cast aluminum wire drive system and dual geared idler and drive roll with de-spooler; the improved design offers integrated feet and torch wrap for cable organization. Specifications: Processes: MIG (GMAW); Flux Cored (FCAW). Input Power: 230V. Amperage Range: 30-190A, DC CV. Wire Diameter Range: .023" - .035". Rated Output: 120A @ 25% Duty Cycle. Plate Thickness Range: 24 ga. - 3/8". Weight: 63 lbs. Dimensions: 19" x 9.5" x 16.5". Duty Cycle: 140A, 21V @ 15% 120A, 20V @ 25%.
   
 
1