Home > HAND TOOLS > CLAMPS / FASTENING TOOLS > TORCHES / SOLDERING > MISC SOLDERING SUPPLIES
Sort By:
1
Oatey 30710 Acid Brush BRSH FLUX 3/PK 3/8IN          Oatey 31410 Cleaning Brush
Use for applying liquid or paste fluxes. For liquid or paste soldering flux. 6" (152.4mm) long and 1/2" (12.7mm) wide. 3-pack. One stainless steel bristled brush for cleaning threads on hard metal pipes and one with brass bristles for use on softer metals. Cleans threaded pipe and fittings, and much more.
Oatey 53026 Wire Solder Oatey 53185 Rosin Core Wire Solder Oatey 53023 Rosin Leaded Core Solder
Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range. Alloy of 60 percent Tin and 40 percent Lead; no external flux is needed. 361 degrees F ? 375 degrees F melting range. Can be used for electrical applications including wiring and other fine electronic work. Contains lead. Not for use on drinking water lines. Alloy of 60 percent Tin and 40 percent Lead; no external flux is needed. 361 degrees F ? 375 degrees F melting range. Can be used for electrical applications including wiring and other fine electronic work. Contains lead. Not for use on drinking water lines.
Oatey 53012 Rosin Leaded Core Solder Safe-Flo 53061 Wire Solder Oatey 53010 Wire Solder
40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F. Alloy of tin, silver, copper and bismuth; works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics with a melting range of 420 to 460 degrees F;  .084" diameter. Used for tin plate work, sheet metal seaming, and hot water heating lines. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. 50 percent tin and 50 percent lead, used with an external flux. Good flow characteristics and low melting point. 361 to 421 degrees Fahrenheit melting range; 0.075" diameter. Used for soldering galvanized gutters, general repairs, radiators, sheet metal and non-drinking water lines. Contains lead, not to be used for plumbing applications.
Oatey 53174 Acid Core Wire Solder Oatey 53011 Leaded Acid Core Solder SLDR 40/60-1/4LB 1/8IN
Lead free alloy of 95 percent Tin and 5 percent Antimony. Acid flux is contained within the core. Used for for sheet metal, radiator, gutter repair work with a melting range of 450 degrees F-464 degrees F; .081" gauge 40 percent tin and 60 percent lead alloy with acid flux contained in wire core; no external flux necessary. For sheet metal work, auto radiator repair, steel gutters and more. Not for use in electrical applications. 361 to 460 degrees Fahrenheit melting range. 0.081" diameter. Contains lead, NOT for plumbing applications. 40 percent tin, 60 percent lead. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). NOT FOR ELECTRICAL CONNECTIONS.
Oatey 53019 Instant Wire Solder SOLDER 1/8IN SW40TIN/60L 1/4LB Oatey 53016 Rosin Core Solder
Easy to use; solder and flux all in one. Can be used on drinking water lines. Includes acid brush. 40 percent tin, 60 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). NOT SUITABLE FOR ALUMINUM. 40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F.
CLOTH EMERY 80GRIT 1INX10YARD CLOTH EMERY 120GRIT 1INX10YARD CLOTH EMERY 180GRIT 1INX10YARD
Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll.
CLOTH EMERY 320GRIT 1INX10YARD SOLDER 3/32IN 40TIN/60L 1/4 LB SLDR 50/50 3/32IN 1/4LB
Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. 40 percent tin, 60 percent lead. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). 50 percent tin and 50 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 5500 PSI. Melting Temp: 421? (216? C). NOT SUITABLE FOR ALUMINUM.
SAND SCREEN 80 GRIT 1-1/2X9FT SAND SCREEN 120 GRIT 1-1/2X9FT SAND SCREEN 180 GRIT 1-1/2X9FT
1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals.
SAND SCREEN 320 GRIT 1-1/2X9FT Oatey 53027 Wire Solder SOLDERING IRON 30 WATT 110V
1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range. For fine wiring, hobbies, models, making jewelry, electronics, TVs, radios, stereos, games, toys, etc. 750 degrees F (398.9 degrees C) tip temperature.
Copper Lock 10-801 No Heat Solder SOLDER 1/16IN 60TIN/40L 1/4LB SOLDERING IRON LT DUTY UL 40W
Fast, easy, permanent; apply inside the copper connector, fit in the copper pipe and within seconds a permanent leakproof seal will occur.  Pressure may be applied after two minutes; can withstand pressures up to 500 PSI; can withstand temperatures from -60 degrees F to +300  degrees F. Meets US Military specifications. Good with all refrigerants. 60 percent tin, 40 percent lead. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Tensile Strength: 6900 PSI. Melting Temp: 375? (190? C).
Oatey 53015 Acid Core Wire Solder Safe-Flo 53062 Wire Solder Oatey 53176 Acid Core Wire Solder
40 percent tin-60 percent lead, .125" gauge; can not be used on drinking lines. Alloy of tin, silver, copper and bismuth. Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics with a melting range of 420 to 460 degrees F;  0.117" diameter. Used for tin plate work, sheet metal seaming, and hot water heating lines. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Lead free alloy of 95 percent Tin and 5 percent Antimony. Acid flux is contained within the core. Used for for sheet metal, radiator, gutter repair work with a melting range of 450 degrees F-464 degrees F; .081" gauge
SOLDER WIRE KITS WATER SOLUBLE Oatey 50193 Acid Core Wire Solder SOLDER 1/8IN 95TIN/5ANT 1/4 LB
General uses: solder pipes, brazing metal, plumbing and automotive repairs. Product details: wire melting temperature: 450 degree F; diameter: 0.062"; wire net weight: .75 oz. silver solder; .5 oz. water soluble paste flux - NSF certified to ANSI/NSF61. Kit contents: 3 oz. solid wire solder, 1 oz. water soluble paste flux, 2-1/4" acid brush, abrasive cloth. Alloy of 40 percent Tin and 60 percent Lead. For repairing galvanized gutters, filling metal seams and other general repairs with a melting range of 360 degrees F - 460 degrees F. Can not be used on drinking water lines; .081" gauge. Tin-antimony "lead-free" solder can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required.
SOLDER COMM 1/8IN 1LB RSN CRE SOLDER 1/8IN AC30TIN/70L 1/2LB Oatey 53014 Leaded Wire Solder
Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Melting Temp: 575? (299? C). 30 percent tin, 70 percent lead. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Tensile Strength: 4500 PSI. Melting Temp: 491? (255? C). NOT FOR ELECTRICAL CONNECTIONS. 50 percent tin and 50 percent lead; use of flux required; .125" gauge. General purpose solder for sheet metal work, auto radiator repair and steel gutters. Contains lead, NOT for plumbing applications.
SOLDER COMM ACID CRE 1LB 1/8IN Weller Featherweight Corded Soldering Iron Oatey 50192 Solid Wire Solder
For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Melting Temp: 575? (299? C). NOT FOR ELECTRICAL CONNECTIONS. For hobbies, kits and radios. Stainless steel barrel, heat and impact resistant pencil handle. Includes No.MT1, 1/8" diameter replaceable nickel-plated copper tip that develops 750 degrees Fahrenheit. 8-1/4"L, 120 Volts, 25 watts, 50/60 Hz. U.L. Listed. Alloy of 50 percent tin and 50 percent lead, use with Oatey #5 paste or liquid flux. Used for sheet metal, galvanized gutters, general repairs and non drinking water lines. Not to be used for plumbing. .125" gauge. Contains lead, NOT for plumbing applications.
Oatey 31400 Flame Protector Safe-Flo 50683 Wire Solder Kit Weller SP15NUS Lightweight Corded Soldering Iron Kit
Heat shield to protect studs, walls, floors, and other surfaces from sparks or flame and is ideal to use with propane and MAPP gas torches for applications up to 2500 degrees F. Made with Zoltek Pyron fibers, a non-asbestos flame retardant material. Size: 9" x 12". Alloy of tin, silver, copper and bismuth. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Provides excellent flow and fill characteristics. 420 to 460 degrees Fahrenheit melting range. Includes 8 oz. solid wire solder 0.117" diameter, 1.7 ozs. No.95 lead free tinning flux, acid brush, sand cloth, and how-to instructions. Pencil-thin for fine soldering and hobby work, small or intricate jobs such as electronics kits, model railways and jewelry making. Stainless steel barrel, heat and impact resistant handle. Includes No.MT70, 1/8" diameter, replaceable, nickel-plated copper, cone shaped tip that develops 750 degrees Fahrenheit. 7"L, 120 Volts, 12 watts, 50/60 Hz. U.L. Listed.
Safe Flo H-20-5 50691 Lead Free Flux Solder Kit SOLDER 1/8IN SW 50/50 1/2LB   SOLDER 1/8IN LF S-WIRE 1/4 LB
IAPMO Listed solder and water soluble flux NSF-61. Flux meets ASTM B-813 standard and is City of L.A. approved. Lead free silver solder meets ASTM B-32 standard. Kit contains: 8 oz., .117" gauge silver lead free solder, 1.7 Oz. H-20-5 water soluble flux, an applicator brush and a sand cloth. 50 percent tin and 50 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 5500 PSI. Melting Temp: 421? (216? C). NOT SUITABLE FOR ALUMINUM. Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C).
Weller SP40NUS Lightweight Corded Soldering Iron Copper Lock 10-800 No Heat Solder Weller BP650MP Cordless Soldering Iron
For hobby and electronic work. Stainless steel barrel, heat and impact resistant pencil handle. Includes No.MT10, 1/4" diameter, replaceable nickel-plated copper tip that develops 900 degrees Fahrenheit. 8-1/4"L, 120 Volts, 40 watts, 50/60 Hz. U.L. Listed. Fast, easy, permanent; apply inside the copper connector, fit in the copper pipe and within seconds a permanent leakproof seal will occur.  Pressure may be applied after two minutes; can withstand pressures up to 500 PSI; can withstand temperatures from -60 degrees F to +300  degrees F. Meets US Military specifications. Good with all refrigerants. Powerful 6-watt/4.5-volt iron heats to working temperature in under 15 seconds. 120 solder joints per set of (3) alkaline batteries. Batteries, lead-free solder,and tip removal tool included. Replacement tips available. Storage cap with auto with power shut-off. Applications: Microelectronics, hobbies, small appliances, and more.
Oatey 20019 Wire Solder Weller 7200PKS Corded Soldering Gun Kit With 2-Wire Corded Safe-Flo 29024 Wire Solder
Alloy of 50 percent tin and 50 percent lead, use with Oatey #5 paste or liquid flux. Used for sheet metal, galvanized gutters, general repairs and non drinking water lines. Not to be used for plumbing. .125" gauge. Contains lead, NOT for plumbing applications. Fingertip trigger, single output from instant-heat gun-ready to solder in 6 seconds. High efficiency, tin-plated, pure copper tip. Lightweight, compact, balanced pistol-grip design with 2-wire cord. Includes No.7200 soldering gun, coil of lead-free rosin core solder, 2 tin-plated copper No.7235 standard chisel tips, and instruction leaflet. 120 Volts, 75 watts, 50/60 Hz. U.L. Listed. Alloy of Tin, Copper, Silver, and Bismuth that works much like 50/50 solder. Recommended for use on potable water systems for sweating copper joints. Also effective on stainless steel, brass alloys, chrome alloys, galvanized steel and cast iron piping.  Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics. 420 to 460 degrees F melting range; 0.117" diameter. Meets ASTM standard B-32 and the requirements of Safe Drinking Water Act. Can Not Be Used On Aluminum.
Weller SP25NKUS General Duty Corded Soldering Iron Kit SOLDER 1/8IN 95TIN/5ANT 1/2 LB Oatey 21018 Wire Solder
For hobbies, kits and radios. Stainless steel barrel with heat and impact resistant pencil handle. With on/off indicator light. Contains No.SP23 soldering iron, three 1/8" diameter nickel-plated copper iron tips, lead-free solder, and soldering aid tool. Tips develop 750 degrees Fahrenheit and include No.MT1 cone-shaped, No.MT2 screwdriver, and No.MT3 chisel tips. Helpful hints and instructions on card. 8-1/4"L, 120 Volts, 25 watts, 50/60 Hz. U.L. Listed. Tin-antimony "lead-free" solder can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. Alloy of 40 percent Tin and 60 percent Lead; 361 degrees F-460 degrees F melting range. Commonly used for tin plating, seaming joints, copper DWV systems and sheet metal repair. Contains lead, NOT for plumbing applications.
KIT SOLDER SILVER SS TUBE     SOLDER 1/8IN LEADFREE SW 1/2LB Oatey 21305 Bar Solder
Premium high strength acid flux cored silver bearing solder for joining all metals except aluminum, magnesium and zinc die cast. 6% silver content. Stays birght and hard. Nontoxic. Joint strength up to 20,000 PSI tensile strength. Weight: 9 oz. Working temperature: 431? F (221.7? C). Application temperature: 400? F to 700? F (204? C to 371? C). Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C). Alloy of 50 percent Tin and 50 percent Lead; 361 degrees F ? 421 degrees F melting range. For use with copper drain piping, tin plating, seaming joints and sheet metal. Not for use on drinking water lines.
SOLDER 1/8IN50/50 SOLIDWIRE1LB SOLDER 1/8IN COM SOLIDWIRE 1LB Oatey 53171 Rosin Core Wire Solder
For general purpose use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. NOT SUITABLE FOR ALUMINUM. 5500 PSI Melting Temp: 421degrees (216 degrees C). For general purpose use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. NOT SUITABLE FOR ALUMINUM. Melting Temp: 575 degrees (299 degrees C). Lead free alloy of 95 percent Tin and 5 percent Antimony. 450 degree F ? 464 degree F melting range. Most commonly used where frequent and extreme temperature changes and vibrations occur. Contains lead, NOT for plumbing applications.
Oatey 21212 Rosin Leaded Core Solder Oatey 21115 Leaded Acid Core Solder Oatey 20015 Leaded Core Solder
40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F. 40 percent tin-60 percent lead, .125" gauge; can not be used on drinking lines. Alloy of 50 percent tin and 50 percent lead. General purpose solder for sheet metal work, auto radiator repair and steel gutters. Not to be used on drinking water lines. .125" gauge. Contains lead, NOT for plumbing applications.
Weller BP865MP Cordless Soldering Iron Safe-Flo 29025 Wire Solder Weller SP80NUS Corded Soldering Iron
Heats up to working temperature in under 15 seconds. White LED light illuminates working surface. Dual power (hi/lo) indicated by red and green LEDs. Co-molded grip for a comfortable feel. Protective safety cap turns off power when placed on tool. Over 150 intermittent solder joints with fresh batteries. Applications: Field service repair on small parts and components. Includes:  Iron, 1 tip, 4 AA batteries, lead free solder, and tip wrench. Alloy of Tin, Copper, Silver, and Bismuth that works much like 50/50 solder. Recommended for use on potable water systems for sweating copper joints. Also effective on stainless steel, brass alloys, chrome alloys, galvanized steel and cast iron piping.  Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics. 420 to 460 degrees F melting range; 0.117" diameter. Meets ASTM standard B-32 and the requirements of Safe Drinking Water Act. Can Not Be Used On Aluminum. For hobby work, stained glass and minor repairs. Stainless steel barrel with heat and impact resistant handle. Includes soldering iron rest and No.MT20, 3/8" diameter, replaceable nickel-plated copper tip that develops 900 degrees Fahrenheit. 9-3/4"L, 120 Volts, 80 watts, 50/60 Hz. U.L. Listed.
SOLDER 1/8IN LEAD FREE SW 1 LB SOLDER 1/8IN 95TIN/5ANT 1 LB  Oatey 22018 Lead Free Plumbing Solder
Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C). Tin-antimony, lead free, can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. Tensile Strength: 6000 PSI. Melting Temp: 464? (240? C). Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range.
SOLDER GUN KIT 140/100W 120V  Bernzomatic 333251 Oxygen Cylinder Bernzomatic 304182 Propane Cylinder
3 built-in LED's illuminate your work; 2 trigger positions 140 W/100 W; ergonomic non-slip grip; 6 seconds heat up; up to 900 degree F. Oxygen cylinders have a CGA 601 valve with left-hand threads. Cylinders are designed to meet Title 49 CFR DOT specification 39 primarily for containing liquefied gas. Propane cylinders have a CGA 600 valve with 1.000 - 20 UNEF-RH - EXT thread. Cylinders are designed to meet Title 49 CFR DOT Specification 39 primarily for containing liquefied gas.
Weller Professional D550 Corded Soldering Gun Weller D550PK Corded Soldering Gun With Twin Lights BUTANE CYLINDER 5.6OZ
High output with 2-position trigger selection of dual heats. Heavy-gauge, high efficiency, tin-plated copper tip comes up to temperature in 6 seconds. Balanced pistol-grip design with twin lights to illuminate work and 2-wire cord. Includes soldering hints booklet. 120 Volts, 260/200 watts, 50/60 Hz. U.L. Listed. High output with 2-position trigger selection of dual heats. Heavy-gauge, high efficiency, tin-plated copper tip comes up to temperature in 6 seconds. Balanced pistol-grip design with twin lights to illuminate work. Includes No.D550 soldering gun, 1 soldering tip, 1 sealing tip, 1 cutting tip, flux brush, soldering aid tool, coil of lead-free rosin core solder, sturdy plastic carrying case and soldering hints booklet. 120 Volts, 260/200 watts, 50/60 Hz. U.L. Listed. Universal fuel tip and additional tips in cap.
Oatey 30712 Acid Brush Map-Pro 332477 Gas Cylinder WELDER ARC STICK 120VOLT 90AMP
Use for applying liquid or paste fluxes. MAP-PRO cylinders have a CGA 600 valve with 1.000 - 20 UNEF - RH - EXT thread. Cylinders are designed to meet Title 49 CFR DOT Specification 39 primarily for containing liquefied gas. Stick welder/TIG capable (TIG torch not included); welds 16 gauge up to 5/16"; handles up to 1/8" electrode; 120V input, 90A output.
WELDER MIG FLUX CORE 120V 125A WELDER MACHINE MIG FC-I 140   WELDER MACHINE MP 140
WELDER MACHINE MP 140
Our Price: $370.19
Gasless/flux-core welding only; 120V input, 125A output; welds 24 gauge up to 1/4"; handles .030" wire. Gasless/flux-core welding only. Welds 24-gauge up to 1/4 in. Handles .030 in. wire. Multi-Process welder: MIG/DC TIG/Stick welder (TIG torch not included). Welds up to 5/16 in. Uses gasless wire .030/.035 in. Solid wire .024/.030 in. Up to 1/8 in. stick electrode.
WELDER ARC AC/DC230V 180A 57LB WELDER MIG 120V 30-140AMP 57LB WELDER MIG 230V 30-190AMP 63LB
This welder has a duty cycle of 20% @ 230A, 50% @ 150A AC, 20% @ 180A and 35% @ 135A DC; the electroholder cable is 3m 25mm2, the earth clamp cable is 2m 25mm2, both with dense connector. Input cable American Wire Gauge (AWG) 10, 2.5mm. 50A plug. CSA-approved. Cat #00329, wheel & handle kit for "Forney" 00313 & 00314 must be purchased separately. Weight: 116 lbs (52.62Kg). Machine for farming, automotive and small welding repair; it runs off household 115V power and offers a duty cycle of 115A @ 20%, 90A @ 35%, 60A @ 60% and 55A @ 100%; the Euro connect Torch with "Tweco" style consumables makes this machine easy to use; the 8" power cord and 10" MIG gun offers 18 feet of work area; better wire feeding is ensured with our cast aluminum wire drive system and dual geared idler and drive roll with de-spooler; the larger cabinet space allows for easier access to 4" and 8" spools; the improved design offers integrated feet and a torch wrap for cable organization. Specifications: Processes: MIG (GMAW); Flux Cored (FCAW). Input Power: 115V. Amperage Range: 30-140A, DC CV. Wire Diameter Range: .023" - .035". Plate Thickness Range: 24 ga. - 1/4". Weight: 57 lbs. Dimensions: 19" x 9.5" x 16.5". Duty Cycle: 115A, 19.75V @ 20%, 90A, 18.5V @ 35%. Regulator and gas hose; offers a Euro Connect Torch and fast disconnect to swap out torch and clean liner; larger cabinet space allows easy access to 4" (1-2lbs) and 8" (10-11lbs) spools; perfect for farms, automotive and repair welding and permits a 25' working envelope with its 10' torch and 15' power cord; the wire feeding is smooth and consistent as this welder has a cast aluminum wire drive system and dual geared idler and drive roll with de-spooler; the improved design offers integrated feet and torch wrap for cable organization. Specifications: Processes: MIG (GMAW); Flux Cored (FCAW). Input Power: 230V. Amperage Range: 30-190A, DC CV. Wire Diameter Range: .023" - .035". Rated Output: 120A @ 25% Duty Cycle. Plate Thickness Range: 24 ga. - 3/8". Weight: 63 lbs. Dimensions: 19" x 9.5" x 16.5". Duty Cycle: 140A, 21V @ 15% 120A, 20V @ 25%.
   
 
1