Home > HAND TOOLS > CLAMPS / FASTENING TOOLS > TORCHES / SOLDERING
Choose a sub category:
TORCH KITS - SOLDER MICRO TORCH KITS TORCH ACCESSORIES - SOLDER
TORCH HEADS SOLDERING & WELDING GASES SOLDER GUNS & IRONS
ELEC SOLDERING GUN ACCESS SOLDER FLUX
MISC SOLDERING SUPPLIES
Sort By:
1
Oatey 30710 Acid Brush Oatey 30011 No. 5 Paste Flux Nokorode 14000 Regular Paste Flux
Use for applying liquid or paste fluxes. Cleans and fluxes at the same time. Blended to clean surface oxidation. 100% lead free. Effective on all metals except aluminum, magnesium, and stainless steel. No pre-cleaning necessary for clean sweat copper fittings, for other applications clean excessive dirt and corrosion. Do not use on electrical parts. Use with solid wire solder. Will not freeze or decompose. No odor. Lead free. Recommended for use on all solder alloys including 95/5 and all lead free solders. Meets Specification O-F-506, Type 1A and A-A-51145, MIL-F-4995-2.
Nokorode Aqua Flux 74044 Paste Flux Oatey No. 95 Tinning Flux BRSH FLUX 3/PK 3/8IN
Creamy, smooth paste formulated to meet ASTM B-813 specifications. Water washable, so it can be flushed from the piping system to limit corrosion. Lead-free and may be used with all types of soft solder including 95/5, 60/40, 50/50 and 40/60 solders. Will not run or drip off acid brushes, pipes and fittings during application. Superior wetting ability allows solder to flow easily and uniformly into joints. Pre-cleans and resists splattering. Conforms to ASTM B-813 specifications. With Oatey silver solder powder added to pre-tin copper pipes. Cleans, fluxes and tins. Lead free, can be used on potable water systems. For clean sweat copper fittings, no pre-cleaning needed. Do not use on electrical parts. Formulated with the same quality as Oatey No.5 flux. Will work for large diameter copper and does not turn copper green. Can never burn out. For liquid or paste soldering flux. 6" (152.4mm) long and 1/2" (12.7mm) wide. 3-pack.
Rectroseal C-Flux Soft Soldering Flux Oatey 53017 Lead Free Soldering Paste Flux Oatey No. 95 Tinning Flux
Lead free, high quality flux containing powdered solder which provides added insurance for a leak free joint. For use with 95/5, 60/40, 50/50, and 40/60 solders. Cleans and fluxes at the same time. Blended to clean surface oxidation. 100% lead free. Effective on all metals except aluminum, magnesium, and stainless steel. No pre-cleaning necessary for clean sweat copper fittings, for other applications clean excessive dirt and corrosion. Do not use on electrical parts. Use with solid wire solder. With Oatey silver solder powder added to pre-tin copper pipes. Cleans, fluxes and tins. Lead free, can be used on potable water systems. For clean sweat copper fittings, no pre-cleaning needed. Do not use on electrical parts. Formulated with the same quality as Oatey No.5 flux. Will work for large diameter copper and does not turn copper green. Can never burn out.
Oatey 31410 Cleaning Brush Oatey 30130 Water Soluble Flux FLINT RENEWALS
One stainless steel bristled brush for cleaning threads on hard metal pipes and one with brass bristles for use on softer metals. Cleans threaded pipe and fittings, and much more. Cleans, removes oxidation, makes solder flow smoothly. Works with all solid wire solders. White paste with low odor. For potable plumbing, copper fire sprinkler and hydronic heating systems. Meets ASTM B-813 standard. IAPMO listed. Flint renewals for spark lighter (5) individual flints.
Nokorode 14010 Regular Paste Flux Oatey 30013 No. 5 Paste Flux Nokorode Aqua Flux 74047 Paste Flux
Will not freeze or decompose. No odor. Lead free. Recommended for use on all solder alloys including 95/5 and all lead free solders. Meets Specification O-F-506, Type 1A and A-A-51145, MIL-F-4995-2. Cleans and fluxes at the same time. Blended to clean surface oxidation. 100% lead free. Effective on all metals except aluminum, magnesium, and stainless steel. No pre-cleaning necessary for clean sweat copper fittings, for other applications clean excessive dirt and corrosion. Do not use on electrical parts. Use with solid wire solder. Creamy, smooth paste formulated to meet ASTM B-813 specifications. Water washable, so it can be flushed from the piping system to limit corrosion. Lead-free and may be used with all types of soft solder including 95/5, 60/40, 50/50 and 40/60 solders. Will not run or drip off acid brushes, pipes and fittings during application. Superior wetting ability allows solder to flow easily and uniformly into joints. Pre-cleans and resists splattering. Conforms to ASTM B-813 specifications.
Oatey 53026 Wire Solder Oatey 53185 Rosin Core Wire Solder PASTE FLUX FOR SOLDER 2 OZ
Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range. Alloy of 60 percent Tin and 40 percent Lead; no external flux is needed. 361 degrees F ? 375 degrees F melting range. Can be used for electrical applications including wiring and other fine electronic work. Contains lead. Not for use on drinking water lines. Plumbers, workers in brass, copper, tin, steel and stained glass will achieve superior results. Produce strong, neat and durable joints. Ruby Fluid allows solder to flow in a thin film. Adheres quickly and stays where it is applied.
Oatey 53023 Rosin Leaded Core Solder LIGHTER FLINT SPARK           Oatey 30106 Soldering Liquid Flux
Alloy of 60 percent Tin and 40 percent Lead; no external flux is needed. 361 degrees F ? 375 degrees F melting range. Can be used for electrical applications including wiring and other fine electronic work. Contains lead. Not for use on drinking water lines. Spark lighter with replaceable flints; used to ignite non-self-lighting torches. Cleans and fluxes. Formulated with strong cleaning agent, no need to clean oxidized copper. Ensures fast and effective soldering. Can be used for HVAC applications.
Oatey H-205 Water Soluble Flux Oatey 53012 Rosin Leaded Core Solder Oatey H-2095 Water Soluble Tinning Flux
Flux for Copper Pipe. As thick as No. 5 flux. Cleans, removes oxidation, makes solder flow smoothly. Works with all solid wire solders. White paste with low odor. For potable plumbing, copper fire sprinkler and hydronic heating systems. Meets ASTM B-813 standard. Made in USA. 40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F. With solder powder added to pre-tin pipes. For potable plumbing, copper fire sprinkler and hydronic heating systems. Safe, lead free, water flushable. Resists burning, will not separate in extreme heat. Stays soft in cold weather. Excellent draw capabilities, as thick as No.5 flux. Meets ASTM B-813, IAPMO Listed.
Safe-Flo 53061 Wire Solder Weller 7250W Standard Soldering Tip Rectroseal C-Flux Soft Soldering Flux
Alloy of tin, silver, copper and bismuth; works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics with a melting range of 420 to 460 degrees F;  .084" diameter. Used for tin plate work, sheet metal seaming, and hot water heating lines. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Made of copper, for Weller soldering guns. Specs: Tip Width O/D .22 in.; Reach/Length 2.57 in. Lead free, high quality flux containing powdered solder which provides added insurance for a leak free joint. For use with 95/5, 60/40, 50/50, and 40/60 solders.
LIQUID FLUX FOR SOLDER 2 OZ   Oatey 53010 Wire Solder Oatey 53174 Acid Core Wire Solder
Plumbers, workers in brass, copper, tin, steel and stained glass will achieve superior results. Produce strong, neat and durable joints. Ruby Fluid allows solder to flow in a thin film. Adheres quickly and stays where it is applied. 50 percent tin and 50 percent lead, used with an external flux. Good flow characteristics and low melting point. 361 to 421 degrees Fahrenheit melting range; 0.075" diameter. Used for soldering galvanized gutters, general repairs, radiators, sheet metal and non-drinking water lines. Contains lead, not to be used for plumbing applications. Lead free alloy of 95 percent Tin and 5 percent Antimony. Acid flux is contained within the core. Used for for sheet metal, radiator, gutter repair work with a melting range of 450 degrees F-464 degrees F; .081" gauge
Weller 7135N Standard Soldering Tip Weller 7135W Standard Soldering Tip Nokorode 14020 Regular Paste Flux
Made of copper, for Weller soldering guns. Specs: Tip O/D  .165 inches; Reach/Length .885 inches. Made of copper, for Weller soldering guns. Specs: Tip Width O/D .165 in.; Reach/Length .885 in. Will not freeze or decompose. No odor. Lead free. Recommended for use on all solder alloys including 95/5 and all lead free solders. Meets Specification O-F-506, Type 1A and A-A-51145, MIL-F-4995-2.
SLDR 40/60-1/4LB 1/8IN        Oatey 53011 Leaded Acid Core Solder SOLDER 1/8IN SW40TIN/60L 1/4LB
40 percent tin, 60 percent lead. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). NOT FOR ELECTRICAL CONNECTIONS. 40 percent tin and 60 percent lead alloy with acid flux contained in wire core; no external flux necessary. For sheet metal work, auto radiator repair, steel gutters and more. Not for use in electrical applications. 361 to 460 degrees Fahrenheit melting range. 0.081" diameter. Contains lead, NOT for plumbing applications. 40 percent tin, 60 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). NOT SUITABLE FOR ALUMINUM.
CLOTH EMERY 80GRIT 1INX10YARD CLOTH EMERY 120GRIT 1INX10YARD CLOTH EMERY 180GRIT 1INX10YARD
Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll.
CLOTH EMERY 320GRIT 1INX10YARD SPREADER FLAME                Oatey 53019 Instant Wire Solder
Hand sanding (dry) and cleaning of metal, wood and pipe ends. Aluminum oxide coating. Open grain prevents loading. 1" x 10 yd bench roll. Flame spreader. Easy to use; solder and flux all in one. Can be used on drinking water lines. Includes acid brush.
Oatey 53016 Rosin Core Solder SOLDER 3/32IN 40TIN/60L 1/4 LB SLDR 50/50 3/32IN 1/4LB
40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F. 40 percent tin, 60 percent lead. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Tensile Strength: 4900 PSI. Melting Temp: 460? (238? C). 50 percent tin and 50 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 5500 PSI. Melting Temp: 421? (216? C). NOT SUITABLE FOR ALUMINUM.
SAND SCREEN 80 GRIT 1-1/2X9FT SAND SCREEN 120 GRIT 1-1/2X9FT SAND SCREEN 180 GRIT 1-1/2X9FT
1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. 1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals.
SAND SCREEN 320 GRIT 1-1/2X9FT Nokorode 14030 All Purpose Regular Paste Flux Oatey 53027 Wire Solder
1-1/2" x 9'. Silicon carbide grain. Non-loading open screen. For wood, paint, ceramic, ferrous and non-ferrous metals. Will not freeze or decompose. No odor. Lead free. Recommended for use on all solder alloys including 95/5 and all lead free solders. Meets Specification O-F-506, Type 1A and A-A-51145, MIL-F-4995-2. Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range.
SOLDERING IRON 30 WATT 110V   Arrow RL100 Light Duty Rivet Tool SOLDER 1/16IN 60TIN/40L 1/4LB
For fine wiring, hobbies, models, making jewelry, electronics, TVs, radios, stereos, games, toys, etc. 750 degrees F (398.9 degrees C) tip temperature. All-steel construction with comfortable vinyl grip. Spring-loaded handle for easy rivet loading and ejection. Changeable nose piece takes 1/8" and 5/32" diameter rivet in one hole and 3/16" in other hole. To change hole size, loosen screw on nose piece plate and pivot plate around, tighten screw. NOTE: Not recommended for use with 3/16" All Steel Rivets. 60 percent tin, 40 percent lead. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Tensile Strength: 6900 PSI. Melting Temp: 375? (190? C).
Copper Lock 10-801 No Heat Solder TORCH PROPANE BRASS PENCIL TIP SOLDER 1/8IN 95TIN/5ANT 1/4 LB
Fast, easy, permanent; apply inside the copper connector, fit in the copper pipe and within seconds a permanent leakproof seal will occur.  Pressure may be applied after two minutes; can withstand pressures up to 500 PSI; can withstand temperatures from -60 degrees F to +300  degrees F. Meets US Military specifications. Good with all refrigerants. Delivers a fine, concentrated flame for pinpoint heating; adjustable flame knob allows for flame control and fuel economy. General uses: soldering pipe; soft solder; thawing pipes; removing paint, tile and putty; lighting pilots and grills. Use with propane fuel only. Tin-antimony "lead-free" solder can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required.
Oatey 53015 Acid Core Wire Solder Safe-Flo 53062 Wire Solder Oatey 53176 Acid Core Wire Solder
40 percent tin-60 percent lead, .125" gauge; can not be used on drinking lines. Alloy of tin, silver, copper and bismuth. Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics with a melting range of 420 to 460 degrees F;  0.117" diameter. Used for tin plate work, sheet metal seaming, and hot water heating lines. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Lead free alloy of 95 percent Tin and 5 percent Antimony. Acid flux is contained within the core. Used for for sheet metal, radiator, gutter repair work with a melting range of 450 degrees F-464 degrees F; .081" gauge
Stanley MR33C Right Angle Riveter SOLDER COMM 1/8IN 1LB RSN CRE SOLDER 1/8IN AC30TIN/70L 1/2LB
Right angle riveter sets 1/8", 5/32" and 3/16" diameter rivets. Spring loaded handle ejects rivet stem automatically, slim nose design fits in tight hard to reach places. Ideal for electrical wiring connections because of its non-conductive residue. Will not cause corrosion or deterioration of electrical connections. Melting Temp: 575? (299? C). 30 percent tin, 70 percent lead. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Tensile Strength: 4500 PSI. Melting Temp: 491? (255? C). NOT FOR ELECTRICAL CONNECTIONS.
SOLDER WIRE KITS WATER SOLUBLE Oatey 50193 Acid Core Wire Solder SOLDER COMM ACID CRE 1LB 1/8IN
General uses: solder pipes, brazing metal, plumbing and automotive repairs. Product details: wire melting temperature: 450 degree F; diameter: 0.062"; wire net weight: .75 oz. silver solder; .5 oz. water soluble paste flux - NSF certified to ANSI/NSF61. Kit contents: 3 oz. solid wire solder, 1 oz. water soluble paste flux, 2-1/4" acid brush, abrasive cloth. Alloy of 40 percent Tin and 60 percent Lead. For repairing galvanized gutters, filling metal seams and other general repairs with a melting range of 360 degrees F - 460 degrees F. Can not be used on drinking water lines; .081" gauge. For sweat fittings, sheet metal joints, gutter work and other big jobs. Works well on galvanized sheet, copper, steel, nickel plate, brass and tin plate. Melting Temp: 575? (299? C). NOT FOR ELECTRICAL CONNECTIONS.
Oatey 53014 Leaded Wire Solder Weller Featherweight Corded Soldering Iron TORCH BUTANE MICRO 3-IN-1
50 percent tin and 50 percent lead; use of flux required; .125" gauge. General purpose solder for sheet metal work, auto radiator repair and steel gutters. Contains lead, NOT for plumbing applications. For hobbies, kits and radios. Stainless steel barrel, heat and impact resistant pencil handle. Includes No.MT1, 1/8" diameter replaceable nickel-plated copper tip that develops 750 degrees Fahrenheit. 8-1/4"L, 120 Volts, 25 watts, 50/60 Hz. U.L. Listed. Refillable, self-lighting micro butane torch; flame adjustment; continuous flame lock; built-in stand and protective cap included; convertible triple function tip; solder tip; hot blow; precision flame; BUTANE FUEL ONLY. General uses: electronic repair, heating shrink tube, small jewelry repair, crafts and hobby, automatic repair, general lighting and cooking.
Oatey 50192 Solid Wire Solder SOLDER 1/8IN SW 50/50 1/2LB   Oatey 31400 Flame Protector
Alloy of 50 percent tin and 50 percent lead, use with Oatey #5 paste or liquid flux. Used for sheet metal, galvanized gutters, general repairs and non drinking water lines. Not to be used for plumbing. .125" gauge. Contains lead, NOT for plumbing applications. 50 percent tin and 50 percent lead. Use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. Tensile Strength: 5500 PSI. Melting Temp: 421? (216? C). NOT SUITABLE FOR ALUMINUM. Heat shield to protect studs, walls, floors, and other surfaces from sparks or flame and is ideal to use with propane and MAPP gas torches for applications up to 2500 degrees F. Made with Zoltek Pyron fibers, a non-asbestos flame retardant material. Size: 9" x 12".
Safe-Flo 50683 Wire Solder Kit Weller SP15NUS Lightweight Corded Soldering Iron Kit SOLDER 1/8IN LF S-WIRE 1/4 LB
Alloy of tin, silver, copper and bismuth. Meets requirements of Safe Drinking Water Act for use on copper potable water lines. Provides excellent flow and fill characteristics. 420 to 460 degrees Fahrenheit melting range. Includes 8 oz. solid wire solder 0.117" diameter, 1.7 ozs. No.95 lead free tinning flux, acid brush, sand cloth, and how-to instructions. Pencil-thin for fine soldering and hobby work, small or intricate jobs such as electronics kits, model railways and jewelry making. Stainless steel barrel, heat and impact resistant handle. Includes No.MT70, 1/8" diameter, replaceable, nickel-plated copper, cone shaped tip that develops 750 degrees Fahrenheit. 7"L, 120 Volts, 12 watts, 50/60 Hz. U.L. Listed. Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C).
Safe Flo H-20-5 50691 Lead Free Flux Solder Kit Copper Lock 10-800 No Heat Solder Weller SP40NUS Lightweight Corded Soldering Iron
IAPMO Listed solder and water soluble flux NSF-61. Flux meets ASTM B-813 standard and is City of L.A. approved. Lead free silver solder meets ASTM B-32 standard. Kit contains: 8 oz., .117" gauge silver lead free solder, 1.7 Oz. H-20-5 water soluble flux, an applicator brush and a sand cloth. Fast, easy, permanent; apply inside the copper connector, fit in the copper pipe and within seconds a permanent leakproof seal will occur.  Pressure may be applied after two minutes; can withstand pressures up to 500 PSI; can withstand temperatures from -60 degrees F to +300  degrees F. Meets US Military specifications. Good with all refrigerants. For hobby and electronic work. Stainless steel barrel, heat and impact resistant pencil handle. Includes No.MT10, 1/4" diameter, replaceable nickel-plated copper tip that develops 900 degrees Fahrenheit. 8-1/4"L, 120 Volts, 40 watts, 50/60 Hz. U.L. Listed.
Weller BP650MP Cordless Soldering Iron Oatey 20019 Wire Solder Arrow RH200 Professional Easy Pull Rivet Tool
Powerful 6-watt/4.5-volt iron heats to working temperature in under 15 seconds. 120 solder joints per set of (3) alkaline batteries. Batteries, lead-free solder,and tip removal tool included. Replacement tips available. Storage cap with auto with power shut-off. Applications: Microelectronics, hobbies, small appliances, and more. Alloy of 50 percent tin and 50 percent lead, use with Oatey #5 paste or liquid flux. Used for sheet metal, galvanized gutters, general repairs and non drinking water lines. Not to be used for plumbing. .125" gauge. Contains lead, NOT for plumbing applications. All steel construction. Comfortable vinyl grip. Spring-loaded handle for easy rivet loading and ejecting. Extended nose for hard-to-get-at places, Locks when not in use. Used on aluminum, canvas, metal; also for installing, repairing and 1,001 uses. Includes 4 nose pieces with wrench. Use 4 rivet sizes: 3/32" (2.5mm), 3/16" (5mm).
SOLDER 1/8IN 95TIN/5ANT 1/2 LB Stanley MR55C5 Right Angle Riveter Weller 7200PKS Corded Soldering Gun Kit With 2-Wire Corded
Tin-antimony "lead-free" solder can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. Spring loaded handle ejects rivets automatically. Sets 1/8", 3/32", 5/32" and 3/16""diameter rivets. All steel construction for long lasting durability, alternate nose pieces and wrench store in handle.  RIGHT ANGLE RIVETER REPLACES MR88. Fingertip trigger, single output from instant-heat gun-ready to solder in 6 seconds. High efficiency, tin-plated, pure copper tip. Lightweight, compact, balanced pistol-grip design with 2-wire cord. Includes No.7200 soldering gun, coil of lead-free rosin core solder, 2 tin-plated copper No.7235 standard chisel tips, and instruction leaflet. 120 Volts, 75 watts, 50/60 Hz. U.L. Listed.
TORCH BRASS HD PENCIL FLAME   Safe-Flo 29024 Wire Solder Weller SP25NKUS General Duty Corded Soldering Iron Kit
An all brass heavy duty pencil flame torch that can be used with MAP/Pro propane fuel or "MAPP"; allows you to perform larger jobs and finish smaller jobs quicker. The torch can handle soldering up to 1" copper tubing. Alloy of Tin, Copper, Silver, and Bismuth that works much like 50/50 solder. Recommended for use on potable water systems for sweating copper joints. Also effective on stainless steel, brass alloys, chrome alloys, galvanized steel and cast iron piping.  Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics. 420 to 460 degrees F melting range; 0.117" diameter. Meets ASTM standard B-32 and the requirements of Safe Drinking Water Act. Can Not Be Used On Aluminum. For hobbies, kits and radios. Stainless steel barrel with heat and impact resistant pencil handle. With on/off indicator light. Contains No.SP23 soldering iron, three 1/8" diameter nickel-plated copper iron tips, lead-free solder, and soldering aid tool. Tips develop 750 degrees Fahrenheit and include No.MT1 cone-shaped, No.MT2 screwdriver, and No.MT3 chisel tips. Helpful hints and instructions on card. 8-1/4"L, 120 Volts, 25 watts, 50/60 Hz. U.L. Listed.
SOLDER 1/8IN LEADFREE SW 1/2LB Oatey 21018 Wire Solder Stanley MR77C Swivel Head Riveter
Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C). Alloy of 40 percent Tin and 60 percent Lead; 361 degrees F-460 degrees F melting range. Commonly used for tin plating, seaming joints, copper DWV systems and sheet metal repair. Contains lead, NOT for plumbing applications. Sets rivets at a right angle or straight on with a simple twist of riveter head, rugged die cast metal construction for extra life. Improved leverage sets 1/8", 3/32", 5/32", and 3/16" diameter with ease. Alternate nose pieces and wrench store in handle.
SOLDER 1/8IN50/50 SOLIDWIRE1LB KIT SOLDER SILVER SS TUBE     Stanley MR100CG Contractor Grade Riveter
For general purpose use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. NOT SUITABLE FOR ALUMINUM. 5500 PSI Melting Temp: 421degrees (216 degrees C). Premium high strength acid flux cored silver bearing solder for joining all metals except aluminum, magnesium and zinc die cast. 6% silver content. Stays birght and hard. Nontoxic. Joint strength up to 20,000 PSI tensile strength. Weight: 9 oz. Working temperature: 431? F (221.7? C). Application temperature: 400? F to 700? F (204? C to 371? C). Rugged die cast metal construction. Sets 1/8", 5/32" and 3/16" diameter rivets. Especially suited for stainless steel rivets in marine applications. Equipped with removable ejector spring.
SOLDER 1/8IN COM SOLIDWIRE 1LB Oatey 21305 Bar Solder Arrow RHT300 Twister Rivet Tool
For general purpose use with appropriate type flux such as Forney 38120, Ruby Fluid, Forney 38125, Paste Flux, or Forney 38127 & 38128, Hi-Temp Fluxes. NOT SUITABLE FOR ALUMINUM. Melting Temp: 575 degrees (299 degrees C). Alloy of 50 percent Tin and 50 percent Lead; 361 degrees F ? 421 degrees F melting range. For use with copper drain piping, tin plating, seaming joints and sheet metal. Not for use on drinking water lines. Unique ``Twistable" Head, rotates 360 degrees for any angle riveting. All-steel construction. Comfortable vinyl grip. Spring-loaded handle for easy rivet loading and ejecting. Extended nose for hard-to-get-at places. Lock clip when not in use. Four nose pieces with wrench. Uses four rivet sizes: 3/32" (2.5mm), 1/8" (3mm), 5/32" (4mm), and 3/16" (5mm). Not for use with stainless steel rivets.
Oatey 53171 Rosin Core Wire Solder TORCH BUTANE MICRO KIT W/CASE Oatey 21212 Rosin Leaded Core Solder
Lead free alloy of 95 percent Tin and 5 percent Antimony. 450 degree F ? 464 degree F melting range. Most commonly used where frequent and extreme temperature changes and vibrations occur. Contains lead, NOT for plumbing applications. Refillable, self-lighting micro butane torch; flame adjustment; continuous flame lock; built-in stand and protective cap included; convertible triple function tip; solder tip; hot blow; precision flame; BUTANE FUEL ONLY. General uses: electronic repair, heating shrink tube, small jewelry repair, crafts and hobby, automatic repair, general lighting and cooking. Kit contents: solder tip, hot knife tip, hot blow tip, sponge, rosin core solder and plastic carry case. 40 percent tin and 60 percent lead alloy with non-corrosive and non-conductive core flux for electrical and electronic soldering such as appliance repair, radio, TV, wiring motors and non-drinking water lines; melting range of 361 to 460 degrees F.
Oatey 21115 Leaded Acid Core Solder Oatey 20015 Leaded Core Solder Weller BP865MP Cordless Soldering Iron
40 percent tin-60 percent lead, .125" gauge; can not be used on drinking lines. Alloy of 50 percent tin and 50 percent lead. General purpose solder for sheet metal work, auto radiator repair and steel gutters. Not to be used on drinking water lines. .125" gauge. Contains lead, NOT for plumbing applications. Heats up to working temperature in under 15 seconds. White LED light illuminates working surface. Dual power (hi/lo) indicated by red and green LEDs. Co-molded grip for a comfortable feel. Protective safety cap turns off power when placed on tool. Over 150 intermittent solder joints with fresh batteries. Applications: Field service repair on small parts and components. Includes:  Iron, 1 tip, 4 AA batteries, lead free solder, and tip wrench.
Safe-Flo 29025 Wire Solder Weller SP80NUS Corded Soldering Iron TORCH SELF LIGHTING
Alloy of Tin, Copper, Silver, and Bismuth that works much like 50/50 solder. Recommended for use on potable water systems for sweating copper joints. Also effective on stainless steel, brass alloys, chrome alloys, galvanized steel and cast iron piping.  Works with any high grade paste or liquid flux and a standard propane torch. Oatey No.95 tinning flux recommended. Provides excellent flow and fill characteristics. 420 to 460 degrees F melting range; 0.117" diameter. Meets ASTM standard B-32 and the requirements of Safe Drinking Water Act. Can Not Be Used On Aluminum. For hobby work, stained glass and minor repairs. Stainless steel barrel with heat and impact resistant handle. Includes soldering iron rest and No.MT20, 3/8" diameter, replaceable nickel-plated copper tip that develops 900 degrees Fahrenheit. 9-3/4"L, 120 Volts, 80 watts, 50/60 Hz. U.L. Listed. Regulated self-lighting propane torch features a stainless steel burn tube for strength and an ergonomic handle providing comfort and durability. The regulated valve delivers the highest quality and consistent triple point flame while operating the torch at any angle. The fuel control knob provides control and economy. Auto igniter for instant flame. Use with propane fuel only.
TORCH BUTANE TABLE TOP 3-IN-1 TORCH SELF LIGHTING           SOLDER 1/8IN LEAD FREE SW 1 LB
Butane powered torch with child-resistant automatic ignition system flame adjustment; 3-in-1 torch tip: precision flame tip, hot blow tip and solder tip; adjustable, wind-resistant flame; runs for approximately 90 minutes (minimum setting) on each fill; torch has standard universal butane refill port; compact size and ergonomic grip; comes with table top stand; continuous flame switch allows for hands-free operation; BUTANE FUEL ONLY. Allows for versatility and ease of operation; the brass regulator valve allows for consistent flame at any angle of operation; the adjustable flame knob allows for flame control and fuel economy; this torch can be used to perform larger jobs or accomplish smaller jobs quicker; the MT 551 can solder up to 1" of copper tubing; use with MAP/Pro propane fuel. Highly recommended for potable water pipe joints, plumbing, refrigeration systems and non-electrical applications. Does not char. Flows evenly within the joint and has a low melting point. Hardens into a shiny fillet. Leaves no corrosive residue. Grade: 95/4.5/.5 Tin/Copper/Silver. Tensile Strength: 6400 PSI; Melting Temp: 430? (222? C).
SOLDER 1/8IN 95TIN/5ANT 1 LB  TORCH SELF LIGHTING HOSE 4FT  SOLDER GUN KIT 140/100W 120V
Tin-antimony, lead free, can be used for soldering potable water pipe joints. Good for plumbing, refrigeration systems and other non-electrical applications where strength is required. Tensile Strength: 6000 PSI. Melting Temp: 464? (240? C). A self-lighted regulated torch that delivers a swirl flame with a 4' flexible extension hose and a belt clip to hold the fuel cylinder; can be used for MAP/Pro or propane fuels. 3 built-in LED's illuminate your work; 2 trigger positions 140 W/100 W; ergonomic non-slip grip; 6 seconds heat up; up to 900 degree F.
Oatey 22018 Lead Free Plumbing Solder TORCH SWIVEL SELF LIGHTING    TORCH ON-DEMAND TRIGGER PRO
Lead free alloy of 95 percent Tin and 5 percent Antimony. Most commonly used where frequent and extreme temperature changes and vibrations occur. Meets the requirements of the Safe Water Drinking Act; 450 degrees F ? 464 degrees F melting range. Self-lighting MAP/Pro or propane torch has a 360 degree swivel that allows for versatility and ease of operation; the brass regulator valve allows for consistent flame at any angle of operation; the adjustable flame knob allows for flame control and fuel economy; this torch can be used to perform larger jobs or accomplish smaller jobs quicker; the MT 555 can solder up to 2" of copper tubing. A high performance Silver Swirl MAP/Pro torch that delivers a swirl flame; has an On-Demand trigger giving you instant ignition and flame shut off; has a safety trigger lock to prevent unwanted ignition and it also has a trigger lock for continuous flame setting; can solder up to 2" of copper tubing; use with MAP/Pro or propane fuel.
TORCH BUTANE MULTI PURPOSE    TORCH SWIVEL ON-DEMAND TRIGGER TORCH BRASS KIT TWO PIECE
Integrated ignition button for easy startup, no independent ignition tool required; variable temperature and flame control for verstile use in both torch and flame mode; 9-piece for wide array of verstile applications; detachable base for hands-free operation; premium quality for long life, durability; filling valve for quick recharge. A high performance torch that delivers a swirl flame; has an On-Demand trigger giving one instant ignition and flame shut off; has safety trigger lock to prevent unwanted ignition and it also has a trigger lock for continuous flame setting; can solder up to 2" of copper tubing. Delivers a fine, concentrated flame or pinpoint heating; adjustable flame knob allows for flame control and fuel economy. General uses: soldering pipe; soft solder; thawing pipes; removing paint, tile and putty; lighting pilots and grills. Kit includes: Brass pencil tip torch and propane cylinder.
Bernzomatic 333251 Oxygen Cylinder Bernzomatic 304182 Propane Cylinder TORCH ON-DEMAND TRIGGER PRO
Oxygen cylinders have a CGA 601 valve with left-hand threads. Cylinders are designed to meet Title 49 CFR DOT specification 39 primarily for containing liquefied gas. Propane cylinders have a CGA 600 valve with 1.000 - 20 UNEF-RH - EXT thread. Cylinders are designed to meet Title 49 CFR DOT Specification 39 primarily for containing liquefied gas. A high performance Silver Swirl MAP/Pro torch that delivers a swirl flame; has an On-Demand trigger giving you instant ignition and flame shut off; has a safety trigger lock to prevent unwanted ignition and it also has a trigger lock for continuous flame setting; can solder up to 2" of copper tubing; use with MAP/Pro or propane fuel.
Weller Professional D550 Corded Soldering Gun Weller D550PK Corded Soldering Gun With Twin Lights BUTANE CYLINDER 5.6OZ
High output with 2-position trigger selection of dual heats. Heavy-gauge, high efficiency, tin-plated copper tip comes up to temperature in 6 seconds. Balanced pistol-grip design with twin lights to illuminate work and 2-wire cord. Includes soldering hints booklet. 120 Volts, 260/200 watts, 50/60 Hz. U.L. Listed. High output with 2-position trigger selection of dual heats. Heavy-gauge, high efficiency, tin-plated copper tip comes up to temperature in 6 seconds. Balanced pistol-grip design with twin lights to illuminate work. Includes No.D550 soldering gun, 1 soldering tip, 1 sealing tip, 1 cutting tip, flux brush, soldering aid tool, coil of lead-free rosin core solder, sturdy plastic carrying case and soldering hints booklet. 120 Volts, 260/200 watts, 50/60 Hz. U.L. Listed. Universal fuel tip and additional tips in cap.
TORCH BRASS KIT PLUMBERS      Oatey 30712 Acid Brush TORCH KIT SELF LIGHTING
Ideal for basic plumbing jobs; the kit contains the MT 200 torch head (sku # 786.1859), 14.1 oz. propane fuel, solder, flux, flux brush; kit also comes with a handy carry case that will easily holds your torch, fuel and accessories. Use for applying liquid or paste fluxes. Regulated self-lighting propane torch features a stainless steel burn tube for strength and an ergonomic handle providing comfort and durability. The regulated valve delivers the highest quality and consistent triple point flame while operating the torch at any angle. The fuel control knob provides control and economy. Auto igniter for instant flame. Kit includes a 14.1 oz. disposable propane fuel cylinder.
TORCH KIT SELF LIGHTING       TORCH SWIVEL ON-DEMAND TRIGGER TORCH KIT DELUXE W/CASE BRASS
Creates a high intensity triple point flame. The fuel tube swivels 360 degrees; all brass valve with brass control knob; package includes the torch and a 14.1 oz. propane cylinder. A high performance torch that delivers a swirl flame; has an On-Demand trigger giving one instant ignition and flame shut off; has safety trigger lock to prevent unwanted ignition and it also has a trigger lock for continuous flame setting; can solder up to 2" of copper tubing. Includes 14.1 oz. disposable MAP/Pro cylinder. Delivers a fine concentrated flame for pinpoint heating. Kit contains an alternate brush flame tip and orifice for broader less direct heat application. An all brass frame spreader can be used to create the widest style flame when needed. All components, including a spark lighter with extra flint renewals can be stored in the custom injected molded carry case. (1) 14.1 oz disposable propane fuel cylinder is included.
TORCH KIT W/CASE BRAZE/WELD   Map-Pro 332477 Gas Cylinder TORCH KIT 3-IN-1 PROFESSIONAL
A brazing/cutting/welding torch kit which features a torch with 2 brass fuel valves: 1 for MAP/Pro and a regulated valve for oxygen; the torch is capable of delivering flame at over 5000 degrees F; braze up tp 1/2" steel; weld up to 3/16" steel; cuts 5/8" bolts and 3/16" steel; works only with MAP/Pro and Oxygen fuels; the torch kit includes the torch and 4-1/2' flexible hose, as well as a carry case with a built in stand both MAP/Pro and Oxygen cylinders, welding rods and a flint spark lighter. MAP-PRO cylinders have a CGA 600 valve with 1.000 - 20 UNEF - RH - EXT thread. Cylinders are designed to meet Title 49 CFR DOT Specification 39 primarily for containing liquefied gas. Contains a MAP/Pro torch head with 3 interchangeable tips (extreme swirl tip, standard swirl tip and pencil point tip); using spin lock technology the user can easily change fuel nozzle and tips ranging from a pencil point flame to the standard swirl flame up to the extreme silver swirl flame; with the interchangeable tips the user can have a pencil tip flame for precise, smaller jobs and tight working spaces; the standard swirl works great for most applications and the extreme silver swirl flame will allow the user to tackle larger jobs (soft solder up to 3" copper fittings) or accomplish smaller jobs more quickly; the custom blow-molded carrying case can carry the torch head, all of the accessory tips as well as up to two fuel cylinders. Kit contents: "Professional On-Demand MAP/Pro" torch with fuel flow adjustment (sku #s 786.1701, 786.1719); extreme swirl tip; standard swirl tip; pencil point tip; 14.1 oz. MAP/Pro cylinder and a custom blow molded case.
   
 
1