Home > HOUSEWARES > KITCHENWARE
Choose a sub category:
FOOD STORAGE COOKWARE BAKEWARE
GADGETS CUTLERY GLASSWARE
DINNERWARE APPLIANCE PARTS SMALL APPLIANCES
PRESSURE COOKERS/CANNERS
Sort By:
1
SCREWS HEX STOVE PIPE BLK ZNC Pellet Pipe 243810 Storm Collar DAMPER STOVEPIPE 5IN CAST IRON
Self-drilling. Hex washer head. 12 screws per pack. Type L pellent vent storm collar used at the top of the flashing to assist in shedding water from the assembly. Used to regulate air by twisting handle to open and close damper. Install in black flue pipe.
Ameri-Vent 8RSC Double Wall Round Storm Collar Imperial BM0247 Trim Stove Pipe Collar Imperial BM0246 Trim Stove Pipe Collar
Use with HS chimney roof flashing to insure water tight installation. Install on wall where flue pipe connects to masonry chimney breech. Install on wall where flue pipe connects to masonry chimney breech.
Imperial BM0245 Trim Stove Pipe Collar Imperial BM0052-A Stove Pipe Damper DAMPER STOVEPIPE 6IN CAST IRON
Install on wall where flue pipe connects to masonry chimney breech. Used to regulate air by twisting handle to open and close damper. Install in black flue pipe. Used to regulate air by twisting handle to open and close damper. Install in black flue pipe.
Ameri-Vent 10RSC Double Wall Round Storm Collar DAMPER STOVEPIPE 8IN CAST IRON STOPPER FLUE ADJ 4-8IN ALMOND
Use with HS chimney roof flashing to insure water tight installation. Used to regulate air by twisting handle to open and close damper. Install in black flue pipe. Used to cover existing flue hole. Adjustable anchors keep stopper securely in place.
Homebasix JI-29C-3L Spice Rack Ultra Temp 208450 Type A Locking Band Selkirk 206810 Storm Collar
Holds 12 jars. Ultra Temp Locking Band, Type A, Stainless Steel, 8 in Width, For use with Chimney Pipe Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning.
Selkirk 208810 Storm Collar TUMBLER STACKING 16OZ GREEN   TUMBLER STACKING 16OZ STAINLES
Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Vacuum insulation keeps drinks cold 4 hours, iced 15 hours, or hot 45 minutes. 18/8 stainless steel won?t rust and naturally BPA-free. Stacks infinitely to save space when packing or storing. Dishwasher safe. 16 Ounce. Vacuum insulation keeps drinks cold 4 hours, iced 15 hours, or hot 45 minutes. 18/8 stainless steel won?t rust and naturally BPA-free. Stacks infinitely to save space when packing or storing. Dishwasher safe. 16 Ounce.
Selkirk 206480 Finishing Collar AmeriVent 6SWA Single Wall Adapter Selkirk 243502 Trim Plate
Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. Included in ceiling support assembly, roof support assembly and tee assembly. Used to finish off the bottom (ceiling) side of a floor/ceiling penetration or on the outside wall as a exterior shield. Over-all size is 12-1/2" x 12-1/2". UL Listed.
Selkirk 243430 Tee Support Sure-Temp 206791 Spark Arrestor Selkirk 243520 Wall Bracket
Type L pellet vent. Can be used to support either a 3" or 4" diameter tee installation. UL Listed. Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. For use on the exterior to support pipe to wall. Use only with Selkirk pellet stove pipe. Hold pipe 3" from wall. UL Listed.
Selkirk Platinum 243006 Double Wall Vent Pipe Selkirk 208480 Finishing Collar Selkirk Platinum 3VP Double Wall Vent Pipe
Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F.
AmeriVent 8SWA Single Wall Adapter Sure-Temp 206465 Fire Stop/Joist Shield Sure-Temp 208790 Spark Arrestor
Included in ceiling support assembly, roof support assembly and tee assembly. Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another. Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.
PMI 10-01704-001 Vacuum Pint Sure-Temp 206520 Wall Band Selkirk Platinum 3VP Double Wall Vent Pipe
Vacuum Insulation. Keeps beer cold for 4.5 hours and cocktails for 17 hours. 18/8 stainless steel. Won?t rust and naturally BPA free. Sweat-free exterior. Press-fit lid. Built-in bottle opener. Dishwasher safe. Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F.
Pellet Pipe 243800 Vertical Termination Stove Pipe Cap 8 in OD PMI Classic Flask PMI Classic One Hand Vacuum Mug
Vertical round top/termination cap. Type L pellet vent. Cap provides necessary protection of the vent system from rain and other elements. UL Listed. 18/8 stainless steel won't rust; naturally BPA free. Single wall. Wide mouth for easy filling and pouring. Integrated lanyard; never lose your cap. Leak proof and fully packable. Vacuum insulated body + thermal lid keep drinks hot 4.5 hours, cold 5 hours or iced 20 hours. 18/8 stainless steel won't rust; naturally BPA free. Push button lid lets you open, drink, close with one hand. Leak proof and fully packable. Dishwasher safe lid disassembles for deep cleaning.
Selkirk 243243 Adjustable Pipe Connector Selkirk A 243825 Adjustable Pellet Vent Roof Flashing Selkirk Platinum 243086 Double Wall Adjustable Length Vent Pipe
Adjustable pipe connector will connect to 3" appliance outlet and is securely fastened with a hose clamp, while the male end adapts to the standard inlet end of 3" VP pipe, elbow or tee. UL Listed. Type L pellet vent. Flashings are used for keeping water and other debris from entering between the pipe and roof. Adjustable pitch. UL Listed. Type L Air Insulated Pellet Vent Adjustable Length Pipe is designed to be telescoped over a fixed length of vent in order to create an assembly of specific length.
American Metal 6HS-SBA 3-Wall Wall Bracket BOTTLE VACUUM 30OZ STAINLESS  PMI Classic Vacuum Mug
Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall. Vacuum insulation keeps drinks cold 9 hours or iced 40 hours. 18/8 stainless steel won?t rust and naturally BPA-free. 3-position lid with rotating cover provides versatility. Reusable straw included. Dishwasher safe. Car cup compatible. Vacuum insulated body and thermal lid. Keeps drinks hot or cold for 7 hours. Push button lid. Open, drink, close with one hand. Leak proof. 18/8 stainless steel. Won?t rust and naturally BPA-free. Dishwasher safe lid. Disassembles for deep cleaning.
Selkirk 206488 Trim Plate Spacer FOOD JAR VACUUM 18OZ STAINLESS FMI 12S-8DM 2-Wall Chimney Support
Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield. Vacuum insulation keeps food hot or cold 12 hours. 18/8 stainless steel won?t rust and naturally BPA-free. Insulated lid doubles as bowl. Wide mouth perfect for soup or chili. Dry storage in stopper for fixings. Full-size Spork included. Leak proof and fully packable. Inner and outer pipe. The outer pipe, made of galvanized steel, provides cooling air necessary to maintain safe chimney temperatures, while the inner pipe, made of stainless steel, emits gases out of the fireplace. Snap- lock design. UL127 Listed. Up to 1700 Degree Pipe.
Sure-Temp 208520 Wall Band American Metal 8HS-SBA 3-Wall Chimney Support Bracket Assembly PMI Classic Vacuum Bottle
Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall. Vacuum Insulated. Keeps drinks hot or cold for 15 hours. 18/8 stainless steel. Won?t rust and naturally BPA-free. Insulated lid that doubles as a cup. Leak proof.
FMI 30FS-8DM Fire Stop Spacer Selkirk Platinum 3VP Double Wall Vent Pipe BOTTLE VACUUM 40OZ STAINLESS
For Comfort Flame systems only. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F. Vacuum insulation keeps drinks cold 11 hours or iced 50 hours. 18/8 stainless steel won?t rust and naturally BPA-free. 3-position lid with rotating cover provides versatility. Reusable straw included. Dishwasher safe. Car cup compatible.
Pellet Pipe 243803 Exit Stove Pipe Cap 5-3/4 in L Ultra Temp 206450 Type A Locking Band Selkirk 206512 Adjustable Pitch Ceiling Plate
Exit Cone Cap is designed to direct flue gases perpendicular to the wall and to increase their velocity, projecting them further away from the building. UL Listed. Ultra Temp Locking Band, Type A, Stainless Steel, 6 in Width, For use with Chimney Pipe Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4" space around chimney pipe (or 2" further than the required clearance).
Pacific Market 10-01229-001 Stanley Vacuum Food Jar PMI Classic Vacuum Bottle American Metal 6FFU 3-Wall Round Roof Vent Flashing
Vacuum Insulation. Keeps food hot or cold for 15 hours. Insulated lid that doubles as a cup. 18/8 stainless steel. Won?t rust and naturally BPA-free. Leak proof. Wide mouth. Perfect for soup or chili. Vacuum Insulated. Keeps drinks hot or cold for 15 hours. 18/8 stainless steel. Won?t rust and naturally BPA-free. Insulated lid that doubles as a cup. Leak proof. Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage.
PMI Classic Vacuum Bottle Pellet Pipe 243230 Type L Vent Stove Pipe Elbow Pellet Pipe 243805 Horizontal Termination Stove Pipe Cap 8 in OD
Vacuum Insulated. Keeps drinks hot or cold for 28 hours. 18/8 stainless steel. Won?t rust and naturally BPA-free. Insulated lid that doubles as a cup. Leak proof. 1.4 quart. Type L vent systems for pellet stove applications.Used to orient pipe between vertical and horizontal orientation. Rated for flue temperatures up to 570 degrees F. Model VP may be installed with a minimum 1" air space clearance to combustible surfaces, framing lumber, drywall, and plywood. UL Listed. Horizontal Termination Cap is designed specifically for use on installations in which the Type L vent terminates in a horizontal orientation on the outside of a structure. UL Listed.
Sure-Temp 206400 Anchor Plate Selkirk 243410 Ceiling Support Pellet Pipe 243460 Wall Thimble
Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Type L pellet vent ceiling support/firestop. Type L Pellet Vent Wall Thimble must be used in all thru-the-wall installations involving combustible construction. UL Listed.
Pellet Pipe 243246 Insulated Type L Chimney Adapter Sure-Temp 206435 Interior Resupport BOTTLE VACUUM GROWLER 64OZ
Type L Pellet Vent to Selkirk Insulated Chimney Adapters are for use in connecting a Model VP Vent System into an existing Selkirk Chimney system. Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance. Vacuum insulated body and foam insulated lid keep beer cold 24 hours. 18/8 stainless steel won?t rust and naturally BPA-free. Heavy duty handle is easy to carry and pours smooth with one hand. Steel inner lid. No plastic contact for your beer. Dishwasher safe.
Selkirk 206242 Drip less Smoke Stove Pipe Adapter Selkirk 206240 Drip less Smoke Stove Pipe Adapter Selkirk Platinum 243060 Double Wall Vent Pipe
For use in retrofit installations, this part can be installed from below with a finish support package and secured with screws. Note: Not for use with coal burning stoves. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F.
Sure-Temp 206463 Insulated Wall Thimble Pellet Pipe 243230B Type L Vent Stove Pipe Elbow Pellet Pipe 243248 Insulated Type L Chimney Adapter
Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Type L vent systems for pellet stove applications.Used to orient pipe between vertical and horizontal orientation. Rated for flue temperatures up to 570 degrees F. Model VP may be installed with a minimum 1" air space clearance to combustible surfaces, framing lumber, drywall, and plywood. UL Listed. Type L Pellet Vent to Selkirk Insulated Chimney Adapters are for use in connecting a Model VP Vent System into an existing Selkirk Chimney system.
Sure-Temp 200420 Roof Support Sure-Temp 200250 Roof Support Selkirk A 206825 Adjustable Roof Flashing
Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only. Flexible roof support designed to fit 5, 6, 7, and 8" diameter chimney. The heavy duty band allows you to slide the length vertically to properly position this section in the system. The URSA can hold up to 30 feet of pipe, only 20 feet can be below. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
Pellet Pipe 243100 Stove Pipe Tee With Cap Selkirk 208240 Drip less Smoke Stove Pipe Adapter American Metal 8FFU 3-Wall Round Roof Vent Flashing
Type L Air Insulated Pellet Vent Tee with Cap designed for use in changing the orientation of the vent from horizontal to vertical and making inspection and cleaning of pellet stove system easier. UL Listed. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage.
Sure-Temp 208463 Insulated Wall Thimble Sure-Temp 206800 Round Type HT Chimney Topper Sure-Temp 208400 Anchor Plate
Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection.
Sure-Temp 206490 Attic Insulation Shield Sure-Temp 206430 Type HT Wall Support Kit Vogelzang BD-06 Barometric Damper
Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall. Prevents over-drafting in wood stoves, coal stoves, circulators and add-on furnaces. Provides a safer, more efficient burn pattern. Automatic combustion control with spin dial. Versatile mounting applications. For use with 6" single wall flue pipe.
Selkirk A 208825 Adjustable Roof Flashing AmeriVent 6HS-WTP 3-Wall Chimney Wall Thimble Selkirk A 206830 Adjustable Roof Flashing
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
Sure-Temp 206440 Roof Brace Kit American Metal 6HS-CSA 3-Wall Ceiling Support Assembly Sure-Temp 208430 Type HT Wall Support Kit
Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'. Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall.
Sure-Temp 208440 Roof Brace Kit AmeriVent 8HS-WTP 3-Wall Chimney Wall Thimble American Metal 6HS-RCS Insulated Chimney Cap
Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'. Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Round termination features its own built-in spark arrestor. Protects against rain, debris and birds entering chimney.
Fulton 1F-72 Flue Stopper Sure-Temp 208490 Attic Insulation Shield Sure-Temp 208800 Round Type HT Chimney Topper
Embossed and decorated of first class material, enamel coated front and back. Clamps of spring wire constructed so they will never lose their strength. Springs will adjust themselves to fit either smooth or irregular flue hole. Colored finish. Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney. Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft.
Selkirk A 208830 Adjustable Roof Flashing Sure-Temp Ultra-Temp 206410 Square Ceiling Support American Metal 8HS-CSA 3-Wall Ceiling Support Assembly
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor.
Sure-Temp Ultra-Temp 206411 Round Ceiling Support FMI V6F-8DM Roof Flashing FMI 30E-8DM Offset and Return Elbow
With proper framing, ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. For 12" standard and high temperature pipe. FMI Offset and Return Elbow, 8 in Nominal, 30 deg Offset, For Wood Burning at 1700 deg Standard Pipes
American Metal 6HS-WS 3-Wall Wall Support Fulton 3F-72 Flue Stopper American Metal 6HS-RSA12 3-Wall Chimney Roof Support
With clean out, heavy gauge base support the chimney tee and chimney. Includes removable outer wall tee cap for clean-out. Embossed and decorated of first class material, enamel coated front and back. Clamps of spring wire constructed so they will never lose their strength. Springs will adjust themselves to fit either smooth or irregular flue hole. Colored finish. For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor.
Vogelzang HR-6 Heat Reclaimer Sure-Temp Ultra-Temp 208410 Square Ceiling Support Sure-Temp 206420 Type HT Roof Support Kit
HR-6 Heat Reclaimer, 6 in
Our Price: $108.00
Attaches to stove pipe and reclaims heat normally lost up the flue. Whisper quiet, safety tested UL fan motor gently blows warm air into the room. Thermostatically controlled, turns on at 160 Deg. Fahrenheit, off at 130 Deg. Fahrenheit. Decorative nickel trim. With proper framing, all ceiling supports provide at least 2" minimum clearance to combustibles at the support level and can carry up to 50' of vertical chimney height. Contains one 18" length of pipe, roof brackets and necessary hardware. Note: Not for use with coal burning stoves.
Sure-Temp 206600 Type HT Roof Termination Kit American Metal 8HS-RSA12 3-Wall Roof Support FMI V12F-8DM Roof Flashing
Includes the basic components for a standard installation; CT - Round Top,  AF-6 - Adjustable Flashing, and SC - Storm Collar. 2/12 - 6-12 pitch. For exposed-beam ceiling installations. Available in flat to 6/12 pitch (Standard) and for steeper pitches of 7/12 to 14/12. Can be used up to 22/12 with double wall connector. Use ceiling support when chimney is to be installed in standard ceiling. Contains stainless steel matte black single wall adaptor. For 12" standard and high temperature pipe.
AmeriVent 8HS-RCS 3-Wall Round Vent Cap Sure-Temp 208420 Type HT Roof Support Kit Selkirk 206100 Insulated Chimney Tee with Tee Cap
Round termination features its own built-in spark arrestor. Protects against rain, debris and birds entering chimney. Contains one 18" length of pipe, roof brackets and necessary hardware. Note: Not for use with coal burning stoves. Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'.
American Metal 6HS-RKS 3 Wall Round Fuel Kit Vogelzang HR-8 Heat Reclaimer FMI CP-8DM Chimney Pack
Built to last with a system combining corrosion resistant stainless steel and sturdy galvanized steel. It features a space-age ceramic fiber refractory blanket to withstand intermittent temperatures up to 2100 degrees F, is  noncombustible, thin and lightweight. It features the same small outer dimensions and is compatible with the AmeriVent Model FB. It is light enough to be easily installed by one man. Kit contains stainless steel cap, standard flashing, storm collar, ceiling support and single wall adaptor. Attaches to stove pipe and reclaims heat normally lost up the flue. Whisper quiet, safety tested UL fan motor gently blows warm air into the room. Thermostatically controlled, turns on at 160 Deg. Fahrenheit, off at 130 Deg. Fahrenheit. Decorative nickel trim. Roof flashing with 24" base, firestop spacer, round termination cap, storm collar and flue extension. Fits standard 8" inner diameter, 12-3/8" outer diameter, 1700 degree pipe.
Sure-Temp 206206 Type HT Insulated Elbow Kit Sure-Temp 208600 Type HT Roof Termination Kit Selkirk 208100 Insulated Chimney Tee with Tee Cap
Can be used for fixed offsets of 15 degrees slope or in pairs for offsets adjustable from zero degrees to 30 degrees slope. Greater angles are prohibited by UL standard 103 and by the terms of the product listing. Required: Locking bands (2 packaged with each elbow kit) allow 360 degree rotation and lock the components together in place at the exact offset required. Insulated elbows can be used at the same two-inch air space clearance as chimney sections. Includes 2 elbows, 2 locking bands and interior resupport. Includes the basic components for a standard installation; CT - Round Top,  AF-6 - Adjustable Flashing, and SC - Storm Collar. 2/12 - 6-12 pitch. Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a Locking Band, to pass safely through combustible walls. An Insulated Tee Cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50'.
American Metal 8HS-RKS 3 Wall Round Fuel Kit Sure-Temp 206621 Pitched Ceiling Support Kit Sure-Temp 206211 Type HT Insulated Elbow Kit
Built to last with a system combining corrosion resistant stainless steel and sturdy galvanized steel. It features a space-age ceramic fiber refractory blanket to withstand intermittent temperatures up to 2100 degrees F, is  noncombustible, thin and lightweight. It features the same small outer dimensions and is compatible with the AmeriVent Model FB. It is light enough to be easily installed by one man. Kit contains stainless steel cap, standard flashing, storm collar, ceiling support and single wall adaptor. For installation of a chimney in a cathedral or pitched ceiling such as standard A-Frame construction. Provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and an adjustable flashing. Selection of the adjustable flashing is determined by the pitch of your roof and ceiling. Contents: Round top, Smoke pipe adapter, Storm collar, Finishing collar, Adjustable pitch ceiling plate and Roof support package. Can be used for fixed offsets of 30 degrees slope. Greater angles are prohibited by UL Standard 103 and by the terms of the product listing. Required: Locking bands (2 packaged with each elbow kit) are to be used at each joint. Each offset must be resupported. Elbows rotate 360 degrees to provide the exact orientation required. Insulated elbows can be used at the same 2'' air space clearance as chimney sections. Kit Includes: 2 elbows, 2 locking bands, and one interior resupport.
Ameri-Vent 6HS-030 3-Wall Chimney Pipe Offset Sure-Temp 206620 Flat Ceiling Support Kit Selkirk 283870 Thru-The-Wall Stove Vent Kit
For use in pairs to permit chimney to "go around" joists, rafters, or other projections. Add chimney section between offsets to produce additional offset. Provides the support package and termination parts for a chimney that is supported by a flat ceiling and that passes through an attic area and penetrates the roof. Just add pipe lengths and the kit has all necessary parts for complete installation. Contents: Round top, Attic insulation shield, Storm collar, Finish support package, Adjustable flashing and Smoke pipe adapter. For pellet and corn appliances. Kit contains: 3" horizontal cap, 3" 90 degree elbow, 3" wall bracket, (5) 3" one-foot pipe lengths, 3" tee with cleanout, 3" wall thimble, and 3" pipe connector. System rated for flue temperatures up to 570 degrees. Proven coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Inner wall is 304 stainless steel, outer wall is paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Meets UL-641 and UL-103.
AmeriVent 6HS-TA 3-Wall Chimney Tee Assembly Sure-Temp 208621 Pitched Ceiling Support Kit Ameri-Vent 8HS-030 3-Wall Chimney Pipe Offset
Chimney tee, tee branch (made up of one 12" section of chimney), single wall adaptor, pipe end plate and tee cap. Use this combination where connection to chimney is made in branch of tee in Through-the-Wall installation. For installation of a chimney in a cathedral or pitched ceiling such as standard A-Frame construction. Provides all necessary parts for a complete installation with the exception of the required insulated pipe lengths and an adjustable flashing. Selection of the adjustable flashing is determined by the pitch of your roof and ceiling. Contents: Round top, Smoke pipe adapter, Storm collar, Finishing collar, Adjustable pitch ceiling plate and Roof support package. For use in pairs to permit chimney to "go around" joists, rafters, or other projections. Add chimney section between offsets to produce additional offset.
Selkirk 284875 High Elevation Stove Vent Kit Sure-Temp 208620 Flat Ceiling Support Kit AmeriVent 8HS-TA 3-Wall Chimney Tee Assembly
For pellet and corn appliances. Kit contains: 4" horizontal cap, 4" 90-degree elbow, 4" wall bracket, (5) 4" one-foot pipe lengths, 4" tee with cleanout, 4" wall thimble, 4" tee support, 3" to 4" pellet increaser, 4" pipe connector, and 3" pipe connector. System rated for flue temperatures up to 570 degrees. Proven coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Inner wall is 304 stainless steel, outer wall is paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Meets UL-641 and UL-103. Provides the support package and termination parts for a chimney that is supported by a flat ceiling and that passes through an attic area and penetrates the roof. Just add pipe lengths and the kit has all necessary parts for complete installation. Contents: Round top, Attic insulation shield, Storm collar, Finish support package, Adjustable flashing and Smoke pipe adapter. Chimney tee, tee branch (made up of one 12" section of chimney), single wall adaptor, pipe end plate and tee cap. Use this combination where connection to chimney is made in branch of tee in Through-the-Wall installation.
Sure-Temp 206622 Thru-the-Wall Support Kit American Metal 6HS-TWK 3-Wall Chimney Installation Kit Sure-Temp 208622 Thru-the-Wall Support Kit
For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running vertically up the exterior wall to termination above the roof line. Provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height. Contents: Round top, 12'' Insulated pipe length, Wall band, Insulated tee/plug, Finishing collar, Wall support kit, Smoke pipe adapter and Insulated wall thimble. Designed for venting appliances through a side wall. Complete wall support components. Provides all-weather protection. For a wall-supported chimney system with a horizontal connector passing through an exterior wall, connecting to a Tee and running vertically up the exterior wall to termination above the roof line. Provides all necessary parts for a complete installation with the exception of required insulated pipe lengths to reach your desired chimney height. Contents: Round top, 12'' Insulated pipe length, Wall band, Insulated tee/plug, Finishing collar, Wall support kit, Smoke pipe adapter and Insulated wall thimble.
United States Stove 1500 Wood/Coal Furnace FURNACE INDOOR WOOD 2500SQFT  FURNACE OUTDOOR WOOD 5000SQFT
FURNACE INDOOR WOOD 2500SQFT
Our Price: $1,747.27
FURNACE OUTDOOR WOOD 5000SQFT
Our Price: $2,969.09
Heats up to 2,500 sq. ft., 70 lb. coal capacity, twin 550 CFM blowers 6.88 Cu. Ft. Firebox, dual 8" duct. Overall dimensions: 24.25"W x 40.25"H x 48D. Depth w/o blower 40". Return air required. NOT APPROVED FOR USE IN MOBILE OR MODULAR HOMES. Not available for sale in WA and CA. EPA Emmissions: Exempt. The dealer is responsible for knowing the regulation in their Provinces, State, city, county, district, or zip code. Universal filter box (SKU# 651-1240) is NOT INCLUDED. Engineered to heat homes up to 2,250 SF. Unit includes filter box (20? x 20?), digital wall thermostat, single speed distribution blower, and ash removal system. Automatic combustion control adjusts heat output to maximize efficiency and distributes heat throughout the home. Pre-wired electrical connections for fast & convenient installation. Specifications: Weight approx. 450 lbs. Dimensions: 50-?"H x 26"W x 44"D  log length, up to 20" firebox volume: 4.0 cf  flue diameter: 6" distribution air and two (2) 8" round collars. EPA-certified. Features a large firebox and is designed for homes up to 5,000 SF. Unit includes filter box (20" x 25"), digital wall thermostat, 3-speed adjustable distribution blower, and 360? roller grate ash removal system. Automatic combustion control adjusts heat output to maximize efficiency and 1800 cfm 3-speed blower distributes heat throughout the home. Pre-wired electrical connections for fast & convenient installation. Specifications: Weight approx. 555 lbs. Dimensions: 50-?"H x 26"W x 50"D log length, up to 26" firebox volume, 5.1 cf, flue diameter: 6? distribution air and two (2) 8? round collars. EPA-certified.
   
 
1