Home > HOUSEWARES > CLEANING SUPPLIES > CLEANING IMPLEMENTS > DIAPER CHANGING STATION
Choose a sub category:
KEROSENE HEATERS-CONVECT/RADIA KEROSENE HEATER ACCESSORIES KEROSENE FUEL
OIL HEATER ACCESSORIES PORTABLE ELECTRIC HEATERS ELECTRIC WALL & CEILING HEATER
GAS HEATERS - NAT GAS HEATERS - LP GAS HEATERS - DUAL FUEL
GAS HEATER ACCESSORIES PROPANE HEATERS TORPEDO HEATERS
OUTDOOR & PATIO HEATERS UTILITY HEATER PARTS & ACC RADIATOR VALVES
Sort By:
1
Harvey's 023015-48 Pipe Joint Compound Harvey 030005-144 Pipe Thread Compound Oatey 31229 Great White
White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape. Pipe thread compound in stick form. Lubricates, seals and prevents rust and corrosion. Use pipe stick on pressures to 2,000 PSI, temperatures to 350 degrees Fahrenheit for metal pipe carrying water, steam, air, ammonia, gasoline, natural gas,  butane, propane, freon, petroleum oil.  DO NOT USE ON OXYGEN SYSTEMS. Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included.
Harvey's 044010 Epoxy Putty Oatey 30999 ABS Cement Harvey's 029035 Pipe Thread Compound
Hardens like steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches holes, cracks and mends almost anything that is broken. Excellent to rebuild or fabricate parts and as an all-purpose adhesive for metals, wood, glass, masonry, ceramics and many plastics. Do not use with polyethylene or polypropylene. Can be drilled, tapped, filed, sanded and painted like metal. Note: You must press until trapped water is forced out from under putty when repairing leaking pipes. Wet putty will require longer cure time. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle.
Oatey 31012 PVC Cement Rectorseal 23710 T-Plus 2 Pipe Thread Sealant Harvey's 018100-24 P-4
Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Oatey 30890 Rain-R-Shine Plumb Pak PP854-2 Pipe Joint Compound Oatey 30883 PVC Cement
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Plumb Pak Pipe Joint Compound, 2 oz, Tube Packing Medium-bodied gray cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Recommended for potable water, pressure pipe, conduit and DWV. Recommended application temperature 40-110 degrees.
Harvey's 018400-24 PVC Cement Oatey 31128 CPVC Pipe and Fitting Cement Rectorseal 25790 Pipe Thread Sealant
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932.
Harvey's 018450-24 P-6E Oatey 30818 All-Purpose Cement Harvey's 018500-24 A-6
For electrical PVC conduit and plumbing PVC applications. Medium bodied, medium set; designed for use on all duct and conduit applications through 6" in diameter. Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified for use in potable water, sewer, drain, and waste and vent systems. UPC listed. Meet requirements of ASTM D-2564. Dauber can. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Harvey's 044150-12 Epoxy Putty Oatey 30850 PVC Cement Oatey 31230 Great White
Hardens like steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches holes, cracks and mends almost anything that is broken. Excellent to rebuild or fabricate parts and as an all-purpose adhesive for metals, wood, glass, masonry, ceramics and many plastics. Do not use with polyethylene or polypropylene. Can be drilled, tapped, filed, sanded and painted like metal. Note: You must press until trapped water is forced out from under putty when repairing leaking pipes. Wet putty will require longer cure time. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included.
Rectorseal 55902 PVC Cement Harvey's 018110-24 P-4 Harvey's 018700-24 C-4
Regular body cement specifically formulated for all PVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers, and drain, waste and vent (DWV). For use on PVC pipe through 2" Schedule 40 pressure piping and up to and including 4" Schedule 40 non-pressure (DWV) piping; it may also be used for making up transition joints between ABS and PVC in non-pressure (DWV) piping. Dauber top. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Harvey's 018200-24 P-2 PVC Cement Oatey 31129 CPVC Pipe and Fitting Cement Harvey's 018000-24 Mp-6
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Oatey 30917 ABS Cement Oatey 31013 PVC Cement Brass Craft PS1087 Seal 'N Check Kit
Medium-bodied ABS resin in solvent solution formula for use on ABS pipe and fittings up to 6" in diameter. Formulated especially for the hot, arid climates in the western states. Use for all non-pressure applications, for all types and grades of ABS pipe and fittings for DWV. Meets ASTM D-2235. SALES AREA - ONLY IN THE WESTERN REGION. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Pipe thread sealant is used to seal male to female pipe threads. The leak detection solution is applied (poured) on the joints of a gas installation to detect unsafe seals in the component-to-component connections (shut-off valve to adapter to gas connector, and gas connector to adapter to appliance regulator). Bubbles in the solution will indicate a leak. The pipe thread sealant is preferred over gas PTFE tape because of its fluidity - it seals up the crevices of the Male to Female thread engagement and provides a better seal. The leak detection solution does not contain soap or detergents, eliminating a false reading.
Plumb Pak PP854-1 Pipe Thread Sealant Oatey 31910 Flow-Guard Gold SCRAPER ERGO 4IN W/OVERMOLD
Plumb Pak Pipe Thread Sealant, Teflon, 1 oz, Tube Packing Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. Use to remove leftover residue from windows, glass and more. Features coated carbon steel blades with a reversible razor edge. An integrated safety guard provides blade protection while a rubber grip helps prevent the scraper from slipping out of your hand for safer, more efficient work. Opens with the push of a button for quick blade replacement and cleaning.
BLADE CARBON SCRAPER REFIL 5PK Harvey's 023030 Pipe Joint Compound Harvey's 025020 Pipe Thread Compound
Replacement carbon coated blades for the Orgill SKU# 934.8574. Includes a carrying case to store and protect blades. Includes 5 replacement blades. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle.
Worldwide Sourcing HG-1 Washing Machine Hose Connectors PC-Plumbing 025598 2-Part Hand Moldable Epoxy Putty Oatey Fix-It Epoxy Putty
Ensures a secure connection between clothes washer drain hoses and standpipes. Fit both 1-1/2" and 2" standpipes and most washing machine hoses 1" - 1-7/16" NSF rating, signifying it safe for contact with potable water. Works wet or dry. For sealing, patching and mending compound. Repairs anything that leaks or is broken. Steel filled, mixes in your hands and hardens in minutes. Perfect for fabricating or rebuilding parts. May be drilled, tapped, filed, sealed and painted. Resists abrasion and a variety of chemicals. Contains no solvents, is non-toxic and will not shrink.
Oatey 30900 ABS/PVC Transition Cement Rectorseal 55970 Abs/PVC/CPVC Cement Harvey's 018510-24 A-6
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Medium body multipurpose cement formulated for use on all PVC, CPVC and ABS pipe applications such as potable water, conduit and drain, waste and vent (DWV). It is for use on all PVC, CPVC and ABS pipe classes for pressure systems through 2" Schedule 40 and non-pressure piping systems through 6" Schedule 40 (excluding Schedule 80), also for use on transition joints to join PVC to CPVC and PVC to ABS. Exceeds ASTM F 493 specifications and is LEED compliant. Dauber top. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Harvey's 018410-24 PVC Cement Harvey's 018210-24 P-12 Ameri-Vent 8RSC Double Wall Round Storm Collar
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Use with HS chimney roof flashing to insure water tight installation.
Oatey 30821 All-Purpose Cement Oatey 31911 Flow-Guard Gold Oatey 30891 Rain-R-Shine
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit.
Fernco PHG-1 Hose Grip Washing Machine Hose Connectors Harvey's 018710-24 C-4 CPVC Cement Oatey 32161 Hot Blue Lava PVC Cement
Securely connects washer's drain hose to any standard laundry standpipe and holds it firmly in place. Fits both 2" and 1-1/2" standpipes and most washing machine hoses from 1" to 1-7/16" diameters. Built from strong, flexible PVC. Carded. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564.
Plumb Pak PP850-3 Utility Hoses Rectorseal 31631 Tru-Blu Rectorseal 23631 T-Plus 2
3/4" Hose Female Connection one end, 1 end plain (no fitting). For use filling wringer-type washing machines, or wherever an extension is needed. Includes washer. Fast drying, adhesive thread sealant especially suited for high vibration environments such as refrigeration or compressor applications. Stays flexible - designed for areas of high vibration and thermal expansion/contraction. Can also be used as a positive lock and seal on threaded fasteners. Lead free and contains no metal. For use with water (hot or cold). Brushable from 20 degree F to 140 degree F. Excellent as a gasket adhesive on flanges. Low odor, non-separating. Lubricates and protects threads. Easy application - brush top applicator. Meets Federal Specification TT-S-1732. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732.
Harvey's 029048 Pipe Thread Compound Harvey's 018010-24 Mp-6 Oatey 15420 Pro Dope
Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Standard oil-based thread sealant ensures exceptional leak-proof joints. For use on metal pipe and fittings carrying water, natural gas, air, steam, ammonia, brine, diluted acids, and alkalis. Uniform, smooth consistency provides for an easy application; will not drip or spill out of container. Long shelf life. Non-setting formula will not harden, crack or become brittle. Lubricates as it forms a tight pressure seal. Inhibits rust and corrosion. Wipes clean from hands. Withstands air/steam pressure to 200 psi and liquid pressure to 250 psi at temperatures ranging from 0 deg F to 350 deg F. NOT FOR LP GAS. Not for use on plastic pipe or fittings. Certified to ANSI/NSF Standard 61, safe for drinking water lines. Meets Fed. Spec. TT-S-1732. Gray.
Rectorseal 25631 Pipe Thread Sealant Oatey 15804 Hercules Pipe Thread Sealant Harvey's 018120-12 P-4
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Harvey's 018220-12 P-2 PVC Cement Oatey 30863 PVC Cement Plumb Pak PP850-8 Washing Machine Inlet Hose
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Rubber washing machine hose. For both hot or cold water. I.O. couplings on straight end for positive seal. Specially compounded to resist hot water softening action. Burst pressure, 800 pounds. Highest quality. Identical to original equipment hose. Female and female coupling.
Oatey 31094 PVC Cement Plumb Pak PP850-2 Washing Machine Inlet Hose Harvey's 023045 Pipe Joint Compound
Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. Rubber washing machine hose. For both hot or cold water. I.O. couplings on straight end for positive seal. Specially compounded to resist hot water softening action. Burst pressure, 800 pounds. Highest quality. Identical to original equipment hose. Female and female coupling. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape.
Oatey 30925 ABS/PVC Transition Cement Harvey's 025050 Pipe Thread Compound Oatey 31014 PVC Cement
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Oatey 30812 Bonding Adhesive POLE CONSUMER 6 FOOT          Oatey 32166 Hot Orange Lava
X-15 PVC bonding adhesive is formulated for use to join two sheets of PVC shower pan liner membrane together. Provides permanent, watertight seal to form larger membrane for use in tile shower or other concealed water-proofing applications. Extends your reach to accommodate most household cleaning tasks without a ladder. Features a unique non-skid, non-marking ball grip to rest your pole on wall without it falling to the ground. A rotating, large hang hole fits almost any hook. Includes a universal thread and press fit cone to attach to your household tools. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846.
Plumb Pak PP850-5 Mixer Hoses Plumb Pak PP850-7 Washing Machine Inlet Hose Ultra Temp 208450 Type A Locking Band
Water mixer. 3/4" female connections. Ideal for use on outdoors and basement showers, basement floors, washing cars, laundry, lawns, etc. With two hose washers. "Y" fitting for high pressure. Rubber washing machine hose. For both hot or cold water. I.O. couplings on straight end for positive seal. Specially compounded to resist hot water softening action. Burst pressure, 800 pounds. Highest quality. Identical to original equipment hose. Female and female coupling. Ultra Temp Locking Band, Type A, Stainless Steel, 8 in Width, For use with Chimney Pipe
Plumb Pak PP23821 Washing Machine Hoses Harvey's 018720-12 C-4 CPVC Cement Harvey's 018420-12 PVC Cement
3/4" FHT x 3/4" FHT. Bulk with flag label Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can.
Selkirk 206810 Storm Collar Harvey's 018020-12 Mp-6 Oatey 15427 Pro Dope
Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Standard oil-based thread sealant ensures exceptional leak-proof joints. For use on metal pipe and fittings carrying water, natural gas, air, steam, ammonia, brine, diluted acids, and alkalis. Uniform, smooth consistency provides for an easy application; will not drip or spill out of container. Long shelf life. Non-setting formula will not harden, crack or become brittle. Lubricates as it forms a tight pressure seal. Inhibits rust and corrosion. Wipes clean from hands. Withstands air/steam pressure to 200 psi and liquid pressure to 250 psi at temperatures ranging from 0 deg F to 350 deg F. NOT FOR LP GAS. Not for use on plastic pipe or fittings. Certified to ANSI/NSF Standard 61, safe for drinking water lines. Meets Fed. Spec. TT-S-1732. Gray.
Plumb Pak PP850-4 Washing Machine Drain Hoses Plumb Pak PP850-6 Washing Machine Hoses Oatey 30834 All-Purpose Cement
Washing machine drain hose with gooseneck tapered to fit 3/4", 7/8" or 1" washing machine drain. One 90 degree elbow end fitting. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product.
Unger  RB10C Scraper Blades Oatey 30902 ABS Cement Oatey 15806 Hercules Pipe Thread Sealant
10 carbon steel blades per dispenser. Reversible: 1/2 sharp, 1/2 blunt blades. For 'ErgoTec, Brute' and Light Duty Scrapers. Replacement blade for Orgill SKU# 1678838. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732.
Selkirk 208810 Storm Collar Rectorseal 25551 Pipe Thread Sealant Harvey's 018320-12 PVC Cement
Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Fast setting, all-weather, medium bodied PVC solvent cement specifically recommended for cold weather and fast setting pressure applications. Recommended for pressure pipe: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Formulated for fast initial set up at temperatures down to 10 degrees fahrenheit. Effective temperature range -15 degrees to 110 degrees fahrenheit. Meets performance requirements of ASTM D-2564. Dauber can.
Oatey 30876 PVC Cement Oatey 31121 PVC Cement Worldwide Sourcing PMB-449 Washing Machine Drain Hoses
Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. Fits 3/4", 7/8", or 1" washing machine drain.
Rectorseal 23551 T-Plus 2 Pipe Thread Sealant Harvey's 093200 Washing Machine Fill Hoses Oatey 31132 PVC Cement
Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Featuring new red for hot/blue for cold, high burst pressure, braided, reinforced EPDM rubber hose. 3/4" female fittings on both ends connect to washer and water supply. Fitting washers included. Medium-bodied clear cement for use on PVC pipe and fittings. Up to 6" diameter. Formulated for fast initial set-up at temperatures down to -15 degrees F to 100 degrees F. schedule 40 and schedule 80. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit, and DWV. Non-pressure, DWV, up through 4" diameter: no primer needed where local codes permit. Meets ASTM D-2564.
Plumb Pak PP850-14 Washing Machine Hoses Oatey 30893 Rain-R-Shine Oatey 31095 PVC Cement
Plumb Pak Washing Machine Hose, 3/4 in Nominal Size, 8 ft Length, Female Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV.
Plumb Pak PP23832 Washing Machine Hoses Fluidmaster 9WM48 No-Burst Oatey 31015 PVC Cement
3/4" FHT x 3/4" FHT. Bulk with flag label Both ends have 3/4" hose fitting. Each foot of No-Burst contains 250 feet of stainless steel wire. Non-toxic polymer core resists chlorine and chloramines. Tightly sealed cone washers. Easy to grip, exceptionally flexible nickel-plated brass hex nuts. 3/4" female hose connectors at both ends. Exceeds all pluming code requirements. Meets agency standards. IAPMO Standard, PS74-95, CSA, SBCCI, FDA, NSF-61, A112.18.6 and UPC. 10-year warranty. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Harvey's 018130-12 P-4 Plumb Pak PP850-12 Dishwasher Discharge Hose HSE DRAIN WSHG MACH CRGTD 10FT
Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. 5/8" I.D. x 6'.  With 2 clamps.
Harvey's 018230-12 P-12 Fluidmaster 9WM60 No-Burst Selkirk 206480 Finishing Collar
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Both ends have 3/4" hose fitting. Each foot of No-Burst contains 250 feet of stainless steel wire. Non-toxic polymer core resists chlorine and chloramines. Tightly sealed cone washers. Easy to grip, exceptionally flexible nickel-plated brass hex nuts. 3/4" female hose connectors at both ends. Exceeds all pluming code requirements. Meets agency standards. IAPMO Standard, PS74-95, CSA, SBCCI, FDA, NSF-61, A112.18.6 and UPC. 10-year warranty. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee.
Harvey's 018030-12 Mp-6 Plumb Pak PP22816 Washing Machine Hoses AmeriVent 6SWA Single Wall Adapter
Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Plumb Pak Washing Machine Hose, 3/4 in Nominal Size, 6 ft Length, FGH x FGH, Stainless Steel Included in ceiling support assembly, roof support assembly and tee assembly.
Oatey 32162 Hot Blue Lava PVC Cement Plumb Pak PP855-74 Dishwasher Discharge Hose Oatey 31105 PVC Cement
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. With 2 clamps. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV.
Oatey 30894 Rain-R-Shine Sure-Temp 206791 Spark Arrestor Oatey 31008 PVC Cement
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Fluidmaster 9WM72 No-Burst Harvey's 025080 Pipe Thread Compound Oatey 15808 Hercules Pipe Thread Sealant
Both ends have 3/4" hose fitting. Each foot of No-Burst contains 250 feet of stainless steel wire. Non-toxic polymer core resists chlorine and chloramines. Tightly sealed cone washers. Easy to grip, exceptionally flexible nickel-plated brass hex nuts. 3/4" female hose connectors at both ends. Exceeds all pluming code requirements. Meets agency standards. IAPMO Standard, PS74-95, CSA, SBCCI, FDA, NSF-61, A112.18.6 and UPC. 10-year warranty. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732.
Plumb Pak PP850-13 Washing Machine Discharge Hoses Harvey's 018430-12 PVC Cement Oatey 31122 PVC Cement
Plumb Pak Washing Machine Discharge Hose, Corrugated, 6 ft Length Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564.
Oatey 32167 Hot Orange Lava Selkirk 208480 Finishing Collar Harvey's 028005-144 Pipe Thread Compound Display
Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. For sealing and lubricating threaded pipe joints. In smooth paste form. For steam, water, air, and natural gas. Does not contain lead. Wipes clean from hands. Hang tab tube.
Oatey 30847 All-Purpose Cement AmeriVent 8SWA Single Wall Adapter Rectorseal 25431 Pipe Thread Sealant
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Included in ceiling support assembly, roof support assembly and tee assembly. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932.
Unger 962720 Tele-Pole Extension Poles Rectorseal 23431 T-Plus 2 Pipe Thread Sealant Oatey 31226 Pipe Joint Compound
For the professional janitorial supply industry. Constructed of anodized aluminum, strong yet lightweight. Ergonomic nylon collar locks and loosens in 1/2 turn. Acme Cone Adapter with acme thread. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Fast set non-hardening paste which lubricates and seals threaded joints. Non-toxic; may be used on water, natural gas, steam and air lines. Perfect for applying gaskets to flanges. Not for use on plastic threads.
Unger  SH00C Ergo Tech Scraper Scrapers Sure-Temp 206465 Fire Stop/Joist Shield Unger DB02 Buckets
Tempered carbon steel blade has blunt edge for cement or stucco work. A razor edge for scraping paint and tape. Handle easily attaches to all Unger poles. Ergonomic grip. Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another. Holds 6 gallons of liquid and accommodates up to an 18" scrubber. Made of heavy-duty polyethylene. Highly-visible measurement marks, accepts casters for easy portability.
HOSE DRAIN WSHG MACH RBR 6FT  Sure-Temp 208790 Spark Arrestor 11FT TELESCOPIC POLE TLREACH
Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. 3-section, inter-lock pole is great for dusting, bulb changing, and other general-purpose tasks. Not recommended for heavy-duty use such as cleaning trucks, siding, or decks.
Plumb Pak PP855-71 Dishwasher Discharge Hose Sure-Temp 206520 Wall Band HOSE DRN DSHWSHR RBR 6FT W/ADP
With 2 clamps. Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall.
Eastman 48377 Washing Machine Hoses Eastman 48378 Washing Machine Hose Eastman 60248 Dual Outlet Washing Machine Outlet Box
One pair - 3/8" stainless steel braided full flow high pressure hoses. Nickel plated brass nut with stainless steel ferrule. Working temperatures - 15 degrees F to 158 degrees F. For residential use only. 3/4" FHT x 3/4" FHT. 1 yr. mfg. warranty. One pair - 3/8" stainless steel braided full flow high pressure hoses. Nickel plated brass nut with stainless steel ferrule. Working temperatures - 15 degrees F to 158 degrees F. For residential use only. 3/4" FHT x 3/4" FHT. 1 yr. mfg. warranty. 3/4" MHT outlet, UPC
Fluidmaster 9WM60P2 No-Burst Washing Machine Fill Hoses HOSE WSH MACH PVC 800PSI 6FT  American Metal 6HS-SBA 3-Wall Wall Bracket
Both ends have 3/4" hose fitting. Each foot of No-Burst contains 250 feet of stainless steel wire. Non-toxic polymer core resists chlorine and chloramines. Tightly sealed cone washers. Easy to grip, exceptionally flexible nickel-plated brass hex nuts. 3/4" female hose connectors at both ends. Exceeds all pluming code requirements. Meets agency standards. IAPMO Standard, PS74-95, CSA, SBCCI, FDA, NSF-61, A112.18.6 and UPC. 10-year warranty. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall.
Selkirk 206488 Trim Plate Spacer FMI 12S-8DM 2-Wall Chimney Support Eastman 60245 Dual Outlet Washing Machine Outlet Box
Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield. Inner and outer pipe. The outer pipe, made of galvanized steel, provides cooling air necessary to maintain safe chimney temperatures, while the inner pipe, made of stainless steel, emits gases out of the fireplace. Snap- lock design. UL127 Listed. Up to 1700 Degree Pipe. 3/4" MHT outlet, UPC
Sure-Temp 208520 Wall Band Eastman 60243 Dual Outlet Washing Machine Outlet Box Eastman 60244/38937 Washing Machine Outlet Box With Valve
Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. 3/4" MHT outlet, UPC Right or left side drain, 1/4 Turn ball valve installed. 1/2"CPVC
Lambro 1790 Dryer Outlet Boxes Abbott Rubber RWPM Washing Machine/Dishwasher Hoses American Metal 8HS-SBA 3-Wall Chimney Support Bracket Assembly
12" x 20" dryer wall box. Prevents duct from being crushed, Flame resistant material, fits between studs and is a space saver. Includes wall  unit and wall trim plate. Pliable construction, suitable for use as dishwasher and washing machine drain, flexible design. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall.
Abbott Rubber 5850R Dishwasher Hose HOSE WSH MACH RD/BLU THRD 2PK FMI 30FS-8DM Fire Stop Spacer
Pliable construction, suitable for use as dishwasher and washing machine drain, flexible design. For Comfort Flame systems only.
Gt Water WP-25 Pump-A-Lot Watts WPWME-1 Washing Machine Outlet Box With Valve Ultra Temp 206450 Type A Locking Band
Includes one water pump model WP10, with 12 foot, 1-1/4" discharge hose. Powered by water, uses no electricity. There are no moving parts and no motors to burn out. Power is regulated by hose bib which pumps to within 1/8" of surface. Non-corrosive and uses 1-1/4" or 1-1/2" discharge hose. Pumps approximately 800 gallons of water per hour. Safe and easy to use. Boxed. Comes complete with two individual 1/4-turn brass valves and white protective enclosure with faceplate. Valves are fitted for standard washing machine hose and 1/2" WaterPEX CrimpRing fittings. Design allows for left, center or right valve and waste mounting. The 6-1/2 x 7-5/8" x 3" enclosure comes complete with brackets for nailing to house framing. (Hoses sold separately). Ultra Temp Locking Band, Type A, Stainless Steel, 6 in Width, For use with Chimney Pipe
Selkirk 206512 Adjustable Pitch Ceiling Plate Abbott Rubber RWNK Washing Machine-Dishwasher Hoses Unger  961880 Extension Poles
Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4" space around chimney pipe (or 2" further than the required clearance). Pliable construction, suitable for use as dishwasher and washing machine drain, flexible design. Anodized aluminum, strong yet lightweight. With ergonomic nylon collar that locks and loosens in 1/2 turn. Snap-in System Adapter with thread is included. Comes with cone adapter to fit Unger products.
Oatey Quadtro 38529/38934 Washing Machine Outlet Box American Metal 6FFU 3-Wall Round Roof Vent Flashing Oatey Quadtro 38568/38822 Washing Machine Outlet Box
Quadtro quarter-turn valves, copper sweat. Can be used in commercial or residential applications which require supply valve and waste drain recessed into the wall. Versatile design allows for right, left, or center drain and bottom or top mount valves. Easily installed and removed test cap does not fall into drain. 2" drain opening fits PVC or ABS Sch 40 DWV pipe. 1/4 turn brass ball valve. Copper sweat. Box made of high impact polystyrene, 4 support brackets included for mounting. Snap-on faceplate frame accomodates up to 1 in. drywall. Easy to remove knockout. Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage. Quadtro single lever ball valve, copper sweat. Can be used in commercial or residential applications which require supply valve and waste drain recessed into the wall. Versatile design allows for right, left, or center drain and bottom or top mount valves. Easily installed and removed test cap does not fall into drain. 2" drain opening fits PVC or ABS Sch 40 DWV pipe. single lever valve. Copper sweat. Box made of high impact polystyrene, 4 support brackets included for mounting. Snap-on faceplate frame accomodates up to 1 in. drywall. Easy to remove knockout.
Oatey Quadtro 38528 Washing Machine Outlet Box Sure-Temp 206400 Anchor Plate Unger  962780 Extension Poles
Quadtro 1/4-turn valves, 1/2" ASTM F1807 PEX.. Can be used in commercial or residential applications which require supply valve and waste drain recessed into the wall. Versatile design allows for right, left, or center drain and bottom or top mount valves. Easily installed and removed test cap does not fall into drain. 2" drain opening fits PVC or ABS Sch 40 DWV pipe. 1/4 turn brass ball valve. Box made of high impact polystyrene, 4 support brackets included for mounting. Snap-on faceplate frame accomodates up to 1 in. drywall. Easy to remove knockout. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Features outer locking cams. The cone is fixed with an ACME thread and has push button locking mechanism to secure and attach cleaning tools.
WASHER OUTLET BOX 1/4 TURN    Sure-Temp 206435 Interior Resupport Selkirk 206242 Drip less Smoke Stove Pipe Adapter
The Quadtro Push Connect washing machine outlet box is the ultimate solution for installation flexibility.  Makes joining copper, CVPC or PEX pipe simple and fast without soldering, crimping, or solvent welding.  Includes disconnect tool.  Allows for right, left, or center drain and bottom or top mount valves. Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance. For use in retrofit installations, this part can be installed from below with a finish support package and secured with screws. Note: Not for use with coal burning stoves.
WM Barr GKP85 Kerosene Fuel WM Barr CKE83 Kerosene Fuel Selkirk 206240 Drip less Smoke Stove Pipe Adapter
Refined to lower the sulfur content, improves air quality and extends wick life. Meets ASTM 1K Specification. Suitable for all kerosene-burning heaters, lamps and stoves. Refined to lower the sulfur content, improves air quality and extends wick life. Meets ASTM 1K Specification. Suitable for all kerosene-burning heaters, lamps and stoves. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe.
Klean-Strip Klean-Heat GKKH99991 Kerosene Heater Fuel Sure-Temp 206463 Insulated Wall Thimble Ameri-Vent 10RSC Double Wall Round Storm Collar
Use kerosene heater fuel alternative in place of K-1 kerosene, in kerosene-burning appliances such as heaters, lamps and stoves.  It contains less sulfur and aromatics. Has no kerosene odor, before, during and after burning. Clear formula burns clean to extend wick life, limit smoke, soot and emissions. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Use with HS chimney roof flashing to insure water tight installation.
Abbott Rubber 5017P Washing Machine Drain Hoses Sure-Temp 200420 Roof Support Sure-Temp 200250 Roof Support
Pliable construction, suitable for use as dishwasher and washing machine drain, flexible design. Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only. Flexible roof support designed to fit 5, 6, 7, and 8" diameter chimney. The heavy duty band allows you to slide the length vertically to properly position this section in the system. The URSA can hold up to 30 feet of pipe, only 20 feet can be below.
Selkirk A 206825 Adjustable Roof Flashing Selkirk 208240 Drip less Smoke Stove Pipe Adapter American Metal 8FFU 3-Wall Round Roof Vent Flashing
Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage.
Klean-Strip E08331 Kerosene Fuel Sure-Temp 208463 Insulated Wall Thimble Sure-Temp 206800 Round Type HT Chimney Topper
Refined to lower the sulfur content, improves air quality and extends wick life. Meets ASTM 1K Specification. Suitable for all kerosene-burning heaters, lamps and stoves. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft.
Sure-Temp 208400 Anchor Plate Sure-Temp 206490 Attic Insulation Shield Sure-Temp 206430 Type HT Wall Support Kit
Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall.
Abbott Rubber 7850R/PSDH14-50 Dishwasher Hose Plumb Pak PP855-72 Dishwasher Drain Hose Selkirk A 208825 Adjustable Roof Flashing
Pliable construction, suitable for use as dishwasher and washing machine drain, flexible design. Reinforced black hose only. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
AmeriVent 6HS-WTP 3-Wall Chimney Wall Thimble Selkirk A 206830 Adjustable Roof Flashing Sure-Temp 206440 Roof Brace Kit
Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'.
Sta-Rite FP0S1250X-08 Flotec American Metal 6HS-CSA 3-Wall Ceiling Support Assembly Sure-Temp 208430 Type HT Wall Support Kit
Submersible utility pump - ideal for removing unwanted water to 3/16" depth. Thermoplastic construction for the highest corrosion-resistance.  Includes 8' power cord, and garden hose adapter. 1200 gph. CSA certified. Use when chimney is installed in standard ceiling. 6" and 8" sizes fit between regular 16" O.C. ceiling joists. For exposed beam ceiling installations, use Roof Support. Cartoned to contain stainless steel matte black single wall adaptor. Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall.
Superior Pump 91250 Continuous Duty Submersible Utility Pump Wayne VIP15 Submersible Utility Pumps Sure-Temp 208440 Roof Brace Kit
1/4 HP split capacitor motor - high efficiency - Low amp draw, 10' grounded waterproof power cord, pumps up to 30 gallons per minute, 1800 gallons per hour, side and bottom intake provides for clog resistant suction, cooler operating 115V motor provides continuous duty, pump will lift water over 25 ft. vertical height, 1-1/4" male iron pipe discharge thread, standard hose adapter included. One year warranty from Superior Pump Co. 1/5 HP reinforced thermoplastic submersible utility pump. Assembled in the US with foreign and domestic parts. Pumps dirty water with small (1/2 in.) solids. Removes water down to 3/8 in. of surface. Corrosion resistant, sealed thermoplastic construction. Fully submersible. Max flow rate is 1800 GPH at 0 ft. 1 1/4 in. discharge with 3/4 in. garden hose adapter. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'.
AmeriVent 8HS-WTP 3-Wall Chimney Wall Thimble American Metal 6HS-RCS Insulated Chimney Cap