Home > HOUSEWARES > CLEANING SUPPLIES > CLEANING IMPLEMENTS > REFRIGERATOR BRUSH/COIL BRUSH
Sort By:
1
Harvey's 023015-48 Pipe Joint Compound Harvey 030005-144 Pipe Thread Compound Oatey 31229 Great White
White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape. Pipe thread compound in stick form. Lubricates, seals and prevents rust and corrosion. Use pipe stick on pressures to 2,000 PSI, temperatures to 350 degrees Fahrenheit for metal pipe carrying water, steam, air, ammonia, gasoline, natural gas,  butane, propane, freon, petroleum oil.  DO NOT USE ON OXYGEN SYSTEMS. Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included.
Harvey's 044010 Epoxy Putty Harvey's 039300 Gas Leak Detectors Oatey 30999 ABS Cement
Hardens like steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches holes, cracks and mends almost anything that is broken. Excellent to rebuild or fabricate parts and as an all-purpose adhesive for metals, wood, glass, masonry, ceramics and many plastics. Do not use with polyethylene or polypropylene. Can be drilled, tapped, filed, sanded and painted like metal. Note: You must press until trapped water is forced out from under putty when repairing leaking pipes. Wet putty will require longer cure time. Detects any gas leak in just a few seconds on all types of tubing, valve, cylinders, pressurized tanks, or any system under air, gas or oxygen pressure. May be used at temperatures between -50 to +160 degrees Fahrenheit. Non-toxic, biodegradable, user friendly, non-corrosive and non-irritating to most skin. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications.
Harvey's 029035 Pipe Thread Compound Oatey 31012 PVC Cement Rectorseal 23710 T-Plus 2 Pipe Thread Sealant
Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732.
Harvey's 018100-24 P-4 Oatey 30890 Rain-R-Shine Plumb Pak PP854-2 Pipe Joint Compound
Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Plumb Pak Pipe Joint Compound, 2 oz, Tube Packing
Oatey 30883 PVC Cement Harvey's 018400-24 PVC Cement Oatey 31128 CPVC Pipe and Fitting Cement
Medium-bodied gray cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Recommended for potable water, pressure pipe, conduit and DWV. Recommended application temperature 40-110 degrees. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed.
Rectorseal 25790 Pipe Thread Sealant Harvey's 018450-24 P-6E Quickie 258 Refrigerator Brush
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. For electrical PVC conduit and plumbing PVC applications. Medium bodied, medium set; designed for use on all duct and conduit applications through 6" in diameter. Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified for use in potable water, sewer, drain, and waste and vent systems. UPC listed. Meet requirements of ASTM D-2564. Dauber can. Reaches into heating vents, grates, dryer vents and lint traps, between radiators, under and around refrigerators and ovens. Removes dust, cobwebs, lint, hair.  20" fiber length bends to reach awkward surfaces where other cleaning tools cannot reach. 56 rows of fiber, 27? overall length. 1 5/8? wire wound nylon tapered fibers fit within narrow grates and other openings. Ergonomic comfort grip.
Oatey 30818 All-Purpose Cement Harvey's 018500-24 A-6 Harvey's 044150-12 Epoxy Putty
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can. Hardens like steel in 20 minutes. For use on plumbing, underwater, bathroom, auto, electrical and most any place in the home. Stops leaks, easy mix, makes repairs fast. Plugs, seals, mends, patches and is non-toxic. Patches holes, cracks and mends almost anything that is broken. Excellent to rebuild or fabricate parts and as an all-purpose adhesive for metals, wood, glass, masonry, ceramics and many plastics. Do not use with polyethylene or polypropylene. Can be drilled, tapped, filed, sanded and painted like metal. Note: You must press until trapped water is forced out from under putty when repairing leaking pipes. Wet putty will require longer cure time.
Oatey 30850 PVC Cement BAND CHIMNEY UNIVERSAL DSP    Oatey 31230 Great White
Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Used to conceal the crimped end on the last length in the system. Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included.
Rectorseal 55902 PVC Cement Harvey's 018110-24 P-4 Harvey's 018700-24 C-4
Regular body cement specifically formulated for all PVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers, and drain, waste and vent (DWV). For use on PVC pipe through 2" Schedule 40 pressure piping and up to and including 4" Schedule 40 non-pressure (DWV) piping; it may also be used for making up transition joints between ABS and PVC in non-pressure (DWV) piping. Dauber top. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Harvey's 018200-24 P-2 PVC Cement Oatey 31129 CPVC Pipe and Fitting Cement Harvey's 018000-24 Mp-6
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Oatey 30917 ABS Cement Oatey 31013 PVC Cement Brass Craft PS1087 Seal 'N Check Kit
Medium-bodied ABS resin in solvent solution formula for use on ABS pipe and fittings up to 6" in diameter. Formulated especially for the hot, arid climates in the western states. Use for all non-pressure applications, for all types and grades of ABS pipe and fittings for DWV. Meets ASTM D-2235. SALES AREA - ONLY IN THE WESTERN REGION. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Pipe thread sealant is used to seal male to female pipe threads. The leak detection solution is applied (poured) on the joints of a gas installation to detect unsafe seals in the component-to-component connections (shut-off valve to adapter to gas connector, and gas connector to adapter to appliance regulator). Bubbles in the solution will indicate a leak. The pipe thread sealant is preferred over gas PTFE tape because of its fluidity - it seals up the crevices of the Male to Female thread engagement and provides a better seal. The leak detection solution does not contain soap or detergents, eliminating a false reading.
Plumb Pak PP854-1 Pipe Thread Sealant Oatey 31910 Flow-Guard Gold Harvey's 023030 Pipe Joint Compound
Plumb Pak Pipe Thread Sealant, Teflon, 1 oz, Tube Packing Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape.
Harvey's 025020 Pipe Thread Compound PC-Plumbing 025598 2-Part Hand Moldable Epoxy Putty Oatey Fix-It Epoxy Putty
Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. NSF rating, signifying it safe for contact with potable water. Works wet or dry. For sealing, patching and mending compound. Repairs anything that leaks or is broken. Steel filled, mixes in your hands and hardens in minutes. Perfect for fabricating or rebuilding parts. May be drilled, tapped, filed, sealed and painted. Resists abrasion and a variety of chemicals. Contains no solvents, is non-toxic and will not shrink.
Oatey 30900 ABS/PVC Transition Cement Rectorseal 55970 Abs/PVC/CPVC Cement Harvey's 018510-24 A-6
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Medium body multipurpose cement formulated for use on all PVC, CPVC and ABS pipe applications such as potable water, conduit and drain, waste and vent (DWV). It is for use on all PVC, CPVC and ABS pipe classes for pressure systems through 2" Schedule 40 and non-pressure piping systems through 6" Schedule 40 (excluding Schedule 80), also for use on transition joints to join PVC to CPVC and PVC to ABS. Exceeds ASTM F 493 specifications and is LEED compliant. Dauber top. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Brass Craft PSC1094L Gas Leak Detectors Harvey's 018410-24 PVC Cement Harvey's 018210-24 P-12
Used for natural, LP gas, mixed, manufactured, and LP gas-air mixtures. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Ameri-Vent 8RSC Double Wall Round Storm Collar Oatey 30821 All-Purpose Cement Oatey 31911 Flow-Guard Gold
Use with HS chimney roof flashing to insure water tight installation. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493.
Oatey 30891 Rain-R-Shine Imperial BM0047 Stove Pipe Starter Joint Harvey's 018710-24 C-4 CPVC Cement
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Used to connect two non-crimped ends of pipe together. Crimped on both ends. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Oatey 32161 Hot Blue Lava PVC Cement Rectorseal 31631 Tru-Blu Rectorseal 23631 T-Plus 2
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Fast drying, adhesive thread sealant especially suited for high vibration environments such as refrigeration or compressor applications. Stays flexible - designed for areas of high vibration and thermal expansion/contraction. Can also be used as a positive lock and seal on threaded fasteners. Lead free and contains no metal. For use with water (hot or cold). Brushable from 20 degree F to 140 degree F. Excellent as a gasket adhesive on flanges. Low odor, non-separating. Lubricates and protects threads. Easy application - brush top applicator. Meets Federal Specification TT-S-1732. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732.
Harvey's 029048 Pipe Thread Compound Harvey's 018010-24 Mp-6 Oatey 15420 Pro Dope
Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Standard oil-based thread sealant ensures exceptional leak-proof joints. For use on metal pipe and fittings carrying water, natural gas, air, steam, ammonia, brine, diluted acids, and alkalis. Uniform, smooth consistency provides for an easy application; will not drip or spill out of container. Long shelf life. Non-setting formula will not harden, crack or become brittle. Lubricates as it forms a tight pressure seal. Inhibits rust and corrosion. Wipes clean from hands. Withstands air/steam pressure to 200 psi and liquid pressure to 250 psi at temperatures ranging from 0 deg F to 350 deg F. NOT FOR LP GAS. Not for use on plastic pipe or fittings. Certified to ANSI/NSF Standard 61, safe for drinking water lines. Meets Fed. Spec. TT-S-1732. Gray.
Rectorseal 25631 Pipe Thread Sealant Oatey 15804 Hercules Pipe Thread Sealant Imperial BM0095 Trim Stove Pipe Collar
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Provides a finished appearance at wall or chimney opening. Install on wall where flue pipe connects to masonry chimney breech.
Imperial BM0093 Trim Stove Pipe Collar Imperial BM0094 Trim Stove Pipe Collar Imperial BM0096 Trim Stove Pipe Collar
Provides a finished appearance at wall or chimney opening. Install on wall where flue pipe connects to masonry chimney breech. Provides a finished appearance at wall or chimney opening. Install on wall where flue pipe connects to masonry chimney breech. Provides a finished appearance at wall or chimney opening. Install on wall where flue pipe connects to masonry chimney breech.
Harvey's 018120-12 P-4 Harvey's 018220-12 P-2 PVC Cement Oatey 30863 PVC Cement
Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Imperial BM0026 Adjustable Flue Stopper Oatey 31094 PVC Cement Harvey's 023045 Pipe Joint Compound
Used to cover existing flue hole. Adjustable anchors keep stopper securely in place. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape.
Oatey 30925 ABS/PVC Transition Cement Harvey's 025050 Pipe Thread Compound Oatey 31014 PVC Cement
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Oatey 30812 Bonding Adhesive Imperial BM0151 Clean Out Crimped Stove Pipe Plug Imperial BM0049 Stove Pipe Starter Joint
X-15 PVC bonding adhesive is formulated for use to join two sheets of PVC shower pan liner membrane together. Provides permanent, watertight seal to form larger membrane for use in tile shower or other concealed water-proofing applications. Used to close off non-crimped end of flue pipe or tee. Aids in cleaning and inspection. Used to connect two non-crimped ends of pipe together. Crimped on both ends.
Oatey 32166 Hot Orange Lava Ultra Temp 208450 Type A Locking Band Harvey's 018720-12 C-4 CPVC Cement
Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846. Ultra Temp Locking Band, Type A, Stainless Steel, 8 in Width, For use with Chimney Pipe Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Harvey's 018420-12 PVC Cement Oatey 34055 Plumbing Access Panel Selkirk 206810 Storm Collar
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Provides a service area for plumbing, electrical, security systems, telephone, TV, computer cables and sprinkler system applications. Reversible - can be flush mounted and surface mounted, no framing required. Made from high-impact ABS. UV-stabilized for outdoor use. Textured surface can be painted, wallpapered or tiled. Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning.
Harvey's 018020-12 Mp-6 Oatey 15427 Pro Dope Imperial BM0039 Stove Pipe Reducer
Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Standard oil-based thread sealant ensures exceptional leak-proof joints. For use on metal pipe and fittings carrying water, natural gas, air, steam, ammonia, brine, diluted acids, and alkalis. Uniform, smooth consistency provides for an easy application; will not drip or spill out of container. Long shelf life. Non-setting formula will not harden, crack or become brittle. Lubricates as it forms a tight pressure seal. Inhibits rust and corrosion. Wipes clean from hands. Withstands air/steam pressure to 200 psi and liquid pressure to 250 psi at temperatures ranging from 0 deg F to 350 deg F. NOT FOR LP GAS. Not for use on plastic pipe or fittings. Certified to ANSI/NSF Standard 61, safe for drinking water lines. Meets Fed. Spec. TT-S-1732. Gray. Connect oval stove opening with round pipe.
Oatey 30834 All-Purpose Cement Oatey 34045 Plumbing Access Panel Oatey 30902 ABS Cement
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Provides a service area for plumbing, electrical, security systems, telephone, TV, computer cables and sprinkler system applications. Reversible - can be flush mounted and surface mounted, no framing required. Made from high-impact ABS. UV-stabilized for outdoor use. Textured surface can be painted, wallpapered or tiled. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications.
Oatey 15806 Hercules Pipe Thread Sealant Selkirk 208810 Storm Collar Rectorseal 25551 Pipe Thread Sealant
For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Designed to fit on the round chimney pipe just above the roof flashing. The upper edge of the collar should be waterproofed with plastic sealer to prevent any water from leaking between the collar and chimney pipe. Part is tightened with screws or tabs after proper positioning. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932.
Harvey's 018320-12 PVC Cement Imperial BM0153 Clean Out Crimped Stove Pipe Plug Oatey 30876 PVC Cement
Fast setting, all-weather, medium bodied PVC solvent cement specifically recommended for cold weather and fast setting pressure applications. Recommended for pressure pipe: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Formulated for fast initial set up at temperatures down to 10 degrees fahrenheit. Effective temperature range -15 degrees to 110 degrees fahrenheit. Meets performance requirements of ASTM D-2564. Dauber can. Used to close off non-crimped end of flue pipe or tee. Aids in cleaning and inspection. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Oatey 31121 PVC Cement Rectorseal 23551 T-Plus 2 Pipe Thread Sealant Imperial BM0013 Adjustable Stove Pipe Elbow
Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Adjustable from 0 to 90 degrees.
Oatey 31132 PVC Cement Oatey 30893 Rain-R-Shine Imperial BM0030 Clean Out Stove Pipe Cap
Medium-bodied clear cement for use on PVC pipe and fittings. Up to 6" diameter. Formulated for fast initial set-up at temperatures down to -15 degrees F to 100 degrees F. schedule 40 and schedule 80. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit, and DWV. Non-pressure, DWV, up through 4" diameter: no primer needed where local codes permit. Meets ASTM D-2564. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Closes off one crimped end of an assembled tee or flue pipe. Aids in cleaning and inspection.
Oatey 31095 PVC Cement Fluidmaster AP0808 Access Panels Homebasix CPB00010BK3L Wood Bag
Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. Easy to install, no framing required, works in walls and ceilings up to 3/4" thick, pops in and out of position, no visible clamps or screws. Great for spa pumps, security systems, computer-audio-tv cables. 36-1/2" L X 18" W.
Oatey 31015 PVC Cement Oatey 34056 Plumbing Access Panel Harvey's 018130-12 P-4
Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Provides a service area for plumbing, electrical, security systems, telephone, TV, computer cables and sprinkler system applications. Reversible - can be flush mounted and surface mounted, no framing required. Made from high-impact ABS. UV-stabilized for outdoor use. Textured surface can be painted, wallpapered or tiled. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Harvey's 018230-12 P-12 Selkirk 206480 Finishing Collar Harvey's 018030-12 Mp-6
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Imperial BM0074 Stove Pipe Reducer AmeriVent 6SWA Single Wall Adapter Oatey 32162 Hot Blue Lava PVC Cement
Imperial Stove Pipe Reducer, Series: 611, 6 X 4 in Nominal, Small End Crimped End, 24 ga Thickness, Black Included in ceiling support assembly, roof support assembly and tee assembly. Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564.
Imperial BM0075 Stove Pipe Reducer Oatey 31105 PVC Cement Oatey 30894 Rain-R-Shine
Imperial Stove Pipe Reducer, Series: 611, 6 X 5 in Nominal, Small End Crimped End, 24 ga Thickness, Black Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit.
Imperial BM0077 Stove Pipe Reducer Sure-Temp 206791 Spark Arrestor Imperial BM0079 Stove Pipe Reducer
Imperial Stove Pipe Reducer, Series: 611, 7 X 6 in Nominal, Small End Crimped End, 24 ga Thickness, Black Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. Imperial Stove Pipe Reducer, Series: 611, 8 X 6 in Nominal, Small End Crimped End, 24 ga Thickness, Black
Oatey 31008 PVC Cement Harvey's 025080 Pipe Thread Compound Selkirk Platinum 243006 Double Wall Vent Pipe
Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F.
Oatey 15808 Hercules Pipe Thread Sealant Unger 965620 Telescopic Window Cleaning Kit Imperial BM0080 Stove Pipe Reducer
For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Eliminates the need for a ladder. Includes a 2 in 1, 12" microfiber scrubber/squeegee and a 5'  telescopic pole with a foam grip. Overall Dimensions: 39.75"L x 11"W x 3.88"D. Weight is 1 lb. Imperial Stove Pipe Reducer, Series: 611, 8 X 7 in Nominal, Small End Crimped End, 24 ga Thickness, Black
Harvey's 018430-12 PVC Cement Oatey 31122 PVC Cement Oatey 32167 Hot Orange Lava
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846.
Selkirk 208480 Finishing Collar Fluidmaster AP1414 Access Panels Harvey's 028005-144 Pipe Thread Compound Display
Round collar fits lower end of suspended insulated chimney pipe to provide finished appearance. Used to attach T-DSA Smoke Pipe Adapter to lower end of chimney or to insulated Tee. Easy to install, no framing required, works in walls and ceilings up to 3/4" thick, pops in and out of position, no visible clamps or screws. Great for spa pumps, security systems, computer-audio-tv cables. For sealing and lubricating threaded pipe joints. In smooth paste form. For steam, water, air, and natural gas. Does not contain lead. Wipes clean from hands. Hang tab tube.
Selkirk Platinum 3VP Double Wall Vent Pipe Oatey 30847 All-Purpose Cement Imperial BM0062 Stove Pipe Increaser
Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Ecco Flue Pipe Increaser, 6 x 8 in Nominal, Crimped End, 24 ga Thickness, Matte, Black
Brass Craft CSSC22-36P Procoat AmeriVent 8SWA Single Wall Adapter Rectorseal 25431 Pipe Thread Sealant
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" ID (5/8" OD) tube with fittings. Included in ceiling support assembly, roof support assembly and tee assembly. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932.
Imperial BM0061 Stove Pipe Increaser Imperial BM0063 Stove Pipe Increaser Rectorseal 23431 T-Plus 2 Pipe Thread Sealant
Ecco Flue Pipe Increaser, 7 x 6 in Nominal, Crimped End, 24 ga Thickness, Matte, Black, For Solid Fuel Appliances Such As Wood Stoves Ecco Flue Pipe Increaser, 8 x 7 in Nominal, Crimped End, 24 ga Thickness, Matte, Black, For Solid Fuel Appliances Such As Wood Stoves Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732.
Oatey 31226 Pipe Joint Compound FLUE PIPE INCREASER 5X6IN BLK Sure-Temp 206465 Fire Stop/Joist Shield
Fast set non-hardening paste which lubricates and seals threaded joints. Non-toxic; may be used on water, natural gas, steam and air lines. Perfect for applying gaskets to flanges. Not for use on plastic threads. Imperial Flue Pipe Increaser, 1-Piece, 5 x 6 in Nominal, 24 ga Thickness, Black Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another.
Sure-Temp 208790 Spark Arrestor Brass Craft CSSC22-48P Procoat Brass Craft CSSL115E-36P Gas Appliance Connector
Diamond shaped 1/2" x 1" mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" ID (5/8" OD) tube with fittings. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Homebasix B19000BK-T3L Firewood Basket Holder Brass Craft CSSD105E-36P Gas Appliance Connector Sure-Temp 206520 Wall Band
Metal sheet material. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall.
Brass Craft CSSC91E-48P Gas Appliance Connectors Imperial BM0040 Oval to Round Stove Pipe Boot Brass Craft CSSD54-60P Procoat
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Connect oval stove opening with round pipe. Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor.
Imperial BM0082 Assembled Tee HY-C COMPANY SLRK Adjustable Log Rack Bracket Kit Selkirk Platinum 3VP Double Wall Vent Pipe
Used to direct exhaust upward. Heavy duty construction. Black-painted tubular steel, Black powder-coated paint finish. Add 2x4s of any length to customize the storage you need ( 2x4s not included). Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F.
Brass Craft CSSD105E-48P Gas Appliance Connectors Imperial BM0083 Pipe Tee Selkirk Platinum 243086 Double Wall Adjustable Length Vent Pipe
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Used to direct exhaust upward. Type L Air Insulated Pellet Vent Adjustable Length Pipe is designed to be telescoped over a fixed length of vent in order to create an assembly of specific length.
Imperial BM0084 Pipe Tee American Metal 6HS-SBA 3-Wall Wall Bracket Imperial BM0085 Pipe Tee
Used to direct exhaust upward. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall. Used to direct exhaust upward.
Brass Craft CSSC91E-48P Gas Appliance Connectors ADAPTOR STOVE 6 IN            Selkirk 206488 Trim Plate Spacer
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. May be required to adapt some stove flue outlets to double wall stove pipe. Used to trim the ceiling when a chimney is supported from above and extended down into room. Also used in conjunction with firestop/joist shield.
FMI 12S-8DM 2-Wall Chimney Support Sure-Temp 208520 Wall Band American Metal 8HS-SBA 3-Wall Chimney Support Bracket Assembly
Inner and outer pipe. The outer pipe, made of galvanized steel, provides cooling air necessary to maintain safe chimney temperatures, while the inner pipe, made of stainless steel, emits gases out of the fireplace. Snap- lock design. UL127 Listed. Up to 1700 Degree Pipe. Used along the wall to provide for 2" clearance and assure stability. Useful for suspending offsets. Required at 8' or closer intervals to stabilize the chimney, wherever it is supported along a vertical wall. Bracket for supporting the chimney pipe offsets, securing outdoor chimney to exterior wall.
ADAPTOR CHIMNEY 6IN           FMI 30FS-8DM Fire Stop Spacer Selkirk Platinum 3VP Double Wall Vent Pipe
Used to complete the connection between DSP double wall stove pipe and any insulated chimney system. For Comfort Flame systems only. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F.
Ultra Temp 206450 Type A Locking Band Selkirk 206512 Adjustable Pitch Ceiling Plate Selkirk 266215 Fixed Stove Pipe Elbow
Ultra Temp Locking Band, Type A, Stainless Steel, 6 in Width, For use with Chimney Pipe Provides a finished appearance where the chimney passes through a sloped ceiling. Matte black finish. Adjusts to multiple roof pitches. Covers 4" space around chimney pipe (or 2" further than the required clearance). Used to offset double wall stove pipe toward insulated chimney. Non-positional connection system allows 360 degree rotation.
American Metal 6FFU 3-Wall Round Roof Vent Flashing Sure-Temp 206400 Anchor Plate Sure-Temp 206435 Interior Resupport
Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection. Allows for two different methods of chimney resupport. First method is used at the immediate section of chimney above the upper elbow of an offset. Second method is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. Support band is clamped around the chimney immediately below a locking band.  Straps are nailed to suitable framing at two inch clearance.
HY-C COMPANY SLRA Adjustable Upright Fire Log Rack Kit HY-C COMPANY SLRS Quarter Cord Small Firewood Storage Log Rack Selkirk 206242 Drip less Smoke Stove Pipe Adapter
Stores your firewood neatly and safely above the ground. Helps protect your firewood from rot, termites and insects. Heavy duty tubular construction. Black-painted tubular steel. Black powder-coated paint finish. Add 2x4s of any length to customize the storage you need (2x4s not included). Keeps your firewood off the ground. Helps protect your firewood from rot, termites and insects. Heavy duty tubular construction. Black powder-coated paint finish. Holds full face cord. For use in retrofit installations, this part can be installed from below with a finish support package and secured with screws. Note: Not for use with coal burning stoves.
Selkirk 206240 Drip less Smoke Stove Pipe Adapter Selkirk Platinum 243060 Double Wall Vent Pipe Sure-Temp 206463 Insulated Wall Thimble
For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Engineered for pellet and corn burning stoves. Coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Painted pipe lengths available for interior use. Inner wall 304 stainless steel, outer wall paintable galvanized. Rolled-over male end eliminates sharp edges. 1" clearance to combustibles. Removable tee cap for inspection and cleaning. Internal spacing bead assures uniform insulating air space between pipe walls. Tested and listed by Underwriters' Laboratories, INC., in accordance with UL-641 Standard for Low Temperature Venting Systems, and applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys. When installed according to Selkirk installation instructions, complies with National Safety Standards such as NFPA-211. Rated for flue temperatures up to 570 degrees F. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25".
HY-C SLRC-XL10 Extra Large Log Rack Cover Imperial BM0014 Adjustable Stove Pipe Elbow Ameri-Vent 10RSC Double Wall Round Storm Collar
Protects firewood from the weather. Keeps wood dry for easier, safer burning. Heavy -duty vinyl construction. Front flap opens for easy access to wood. hook and loop closure strips allow front flap to be securely closed Adjustable from 0 to 90 degrees. Use with HS chimney roof flashing to insure water tight installation.
Homebasix CPO90503AC3L Log Rack CAP AND TEE 6 INCH            Sure-Temp 200420 Roof Support
17-1/4" L x 13-1/4" W x 14-1/2" H Used in conjunction with a vertical insulated chimney to provide easy access for inspection and cleaning. Fits all roof pitches and requires only simple framing. Brackets and mounting hardware only.
Sure-Temp 200250 Roof Support Selkirk A 206825 Adjustable Roof Flashing HY-C COMPANY SLRM Half Face Cord Medium Firewood Storage Log Rack
Flexible roof support designed to fit 5, 6, 7, and 8" diameter chimney. The heavy duty band allows you to slide the length vertically to properly position this section in the system. The URSA can hold up to 30 feet of pipe, only 20 feet can be below. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Keeps your firewood off the ground. Helps protect your firewood from rot, termites and insects. Heavy duty tubular construction. Black powder-coated paint finish. Holds full face cord.
Imperial BM0015 Adjustable Stove Pipe Elbow Selkirk 208240 Drip less Smoke Stove Pipe Adapter Imperial BM0023 1-Piece Corrugated Stove Pipe Elbow
Adjustable from 0 to 90 degrees. For use in new installations, this part can be installed by twist-locking the coupler on the DSAC into the first section of Sure-Temp-Type HT chimney pipe. Used to connect two lengths of flue pipe together.
American Metal 8FFU 3-Wall Round Roof Vent Flashing Sure-Temp 208463 Insulated Wall Thimble Selkirk 266230 Fixed Stove Pipe Elbow
Standard flashings fit various pitch roofs. Its double seamed construction protects from water leakage. Installs quickly and eliminates need for using individual firestops. Round shielding acts as a radiation shield and provides the required 2" air space clearance to combustibles. The 2 sections telescope to accommodate 6" to 11" wall thickness. The hole opening in the faceplate for No. 206463 is 8.25"; for No. 207463 - 9.25"; and No. 208463 - 10.25". Used to offset double wall stove pipe toward insulated chimney in a through-the-wall installation. Non-positional connection system allows 360 degree rotation.
Sure-Temp 206800 Round Type HT Chimney Topper Imperial BM0016 Adjustable Stove Pipe Elbow Sure-Temp 208400 Anchor Plate
Designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. Adjustable from 0 to 90 degrees. Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy gauge steel construction for long life. Retains chimney with a twist-lock connection.
Homebasix A910BK-C Log Rack Sure-Temp 206490 Attic Insulation Shield Imperial BM0025 1-Piece Corrugated Stove Pipe Elbow
Size 48"x14"x48". Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney. Used to connect two lengths of flue pipe together.
Sure-Temp 206430 Type HT Wall Support Kit HY-C SLRL Large Tubular Deluxe Log Rack Selkirk A 208825 Adjustable Roof Flashing
Tested for use fully enclosed and has been designed in 5, 6, 7 and 8 inch sizes to carry up to 60' of height. Intended for use with the Insulated Tee as an interior or exterior support where the chimney has a lateral connection. Also useful where the pipe connection passes through a combustible interior or exterior wall. Braces may only be fastened to the wall above or below the plate for chimneys which penetrate through the wall. Keeps your firewood off the ground. Helps protect your firewood from rot, termites and insects. Heavy duty tubular construction. Black powder-coated paint finish. Holds full face cord. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings.
AmeriVent 6HS-WTP 3-Wall Chimney Wall Thimble Selkirk A 206830 Adjustable Roof Flashing Sure-Temp 206440 Roof Brace Kit
Used with tee branch and chimney section to provide proper clearance to combustible materials. Matte black painted surface for interior wall eliminates need for trim plate. Used to seal the opening where the chimney penetrates the roof and to direct rain and snow down from the roof and away from the chimney system. A series of adjustable flashings are available depending on your roof pitch. A flat and low pitch flashing is used to seal flat and low pitch roof (up to 2/12 pitch) openings. Chimney support, use whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load, and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4' to 6'.