Home > HEATING & COOLING > VENTING & FANS > BATH FANS & VENTILATION > BATHROOM VENT HOSE/PIPE
Choose a sub category:
DISCHARGE HOSES SUCTION HOSES HOSE COUPLINGS
GASKETS / WASHERS HOSE ACCESSORIES / TOOLS
Sort By:
1
Oatey 39100/33460 Test Caps Oatey 39101/33461 Test Caps Oatey 39102/33462 Test Caps
Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS. Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS. Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS.
Oatey 39103/33463 Test Caps Frost King FC1 Faucet Cover American Valve P600CTS 1/2 CPVC Fitting
Inexpensive, disposable test caps for pressure testing ABS or PVC with up to 10 pounds pressure. Cap is solvent welded inside open pipe end. After test the center is knocked out and thrown away. Made of ABS. Insulates outside faucets to help prevent freezing. For use in general piping applications,using copper tube sized pipe. Easy to operate for instant emergency piping. Piping must be restrained
Frost King FC2 Faucet Cover KBI SNX Snap-Fix Pipe Repair Coupling TVM IK00011 Foil Tape
Insulates outside faucets to help prevent freezing. NSF Standard 61 listed. Compact design. Unique positive snapping lock assures strong seal without the need to hold product in place. (Strong, fast and permanent). Meets/exceeds ASTM and ANSI standards. Made with high-impact PVC Type II Cell Class 15344-C. Carded. Made of a special UV metallized polypropylene film, with a high tack acrylic adhesive.
Fernco PQC-101 Qwik Caps M-D 03939 Cold Weather Faucet Cover Worldwide Sourcing TC-15 Flexible Test Caps
Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926. Protects faucets from frigid weather, helps prevent frozen pipes, made from weather resistant rigid foam, easy to install. For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602.
Lambro 1317 Flexible Dryer Vent Hose B and K Industries 160-203HC CPVC Fitting KBI SNX Snap-Fix Pipe Repair Coupling
Lambro Dryer Vent Hose, Flexible, 3 in Nominal, 8 ft Length, Vinyl, White, Polybag CPVC body, nut, rubber gaskets, rated at 100 PSI up to 180 deg F. Pipe must be restrained after installation, Use in piping or repairs on copper or plastic pipe. NSF approved. NSF Standard 61 listed. Compact design. Unique positive snapping lock assures strong seal without the need to hold product in place. (Strong, fast and permanent). Meets/exceeds ASTM and ANSI standards. Made with high-impact PVC Type II Cell Class 15344-C. Carded.
Worldwide Sourcing TC-2 Flexible Test Caps Fernco PQC-102 Qwik Caps Frost King FC3 Slip-On Faucet Protector
For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602. Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926. Insulates outside faucets to help prevent freezing.
Oatey 33400 Mechanical Test Plug B and K Industries 160-204HC CPVC Fitting Worldwide Sourcing TC-3 Flexible TestCaps
Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG CPVC body, nut, rubber gaskets, rated at 100 PSI up to 180 deg F. Pipe must be restrained after installation, Use in piping or repairs on copper or plastic pipe. NSF approved. For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602.
American Valve P600CTS 3/4 CPVC Fitting KBI SNX Snap-Fix Pipe Repair Coupling Fernco PQC-103 Qwik Caps
For use in general piping applications,using copper tube sized pipe. Easy to operate for instant emergency piping. Piping must be restrained NSF Standard 61 listed. Compact design. Unique positive snapping lock assures strong seal without the need to hold product in place. (Strong, fast and permanent). Meets/exceeds ASTM and ANSI standards. Made with high-impact PVC Type II Cell Class 15344-C. Carded. Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926.
B and K 160-603 Pipe Repair Clamps B and K Industries 160-602 Pipe Repair Clamp Lambro 1309 Flexible Dryer Vent Hose
Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Lambro Dryer Vent Hose, Flexible, 4 in Nominal, 8 ft Length, Vinyl, White
Worldwide Sourcing TC-4 Flexible Test Caps Fernco PQC-104 Qwik Caps Lambro 1303 Industries Vent Hose with Clamp
For capping pipe ends. Convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. For temporary or permanent use. Can be use with any material. Suitable for underground use. Not for use on pressurized plumbing systems. Meets ASTM C-1173, C-1277, C1460, CISPI 310, IAPMO PS 109, PS90, & CSA B602. Easy way to cap pipe ends, clean-outs and open test pipes. Made of flexible PVC, they're suitable for above ground or underground use, on cast iron, steel, copper or plastic piping. Designed to fit all drain, waste, and vent pipe materials in a given nominal size. The convex face allows the cap to withstand greater pressure for testing purposes and minimizes ballooning. To install, simply place over open end of pipe and tighten to 60" pounds torque. Complies with ASTM D5926. Includes hose and 2 plastic clamps. Not recommended for dryer venting or high temperature venting. Polybagged.
B and K 160-604 Pipe Repair Clamps Oatey 33401 Mechanical Test Plug Thermwell FV15H Frost King
Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG 1/8" thick, self adhesive vinyl foam and aluminum foil insulation tape for hot and cold pipes. 2"W  x 15'L.
B and K 160-605 Pipe Repair Clamps Oatey 33402 Mechanical Test Plug Simmons 31/2OD Standard Water Well Pump Valve
Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG Waterproof impregnated lower valve for regular service.
M-D Building Products 02378 Pipe Wrap Tape B and K 160-606 Pipe Repair Clamps Simmons 1-11/16X5/8 Pump Cup
Polyvinyl chloride foam with aluminum shell that reflects heat. Adhesive closed-cell foam insulates and protects. Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder.
Plumb Pak PP840-1 Pipe Repair Clamps Oatey 33403 Mechanical Test Plug B and K 160-608 Pipe Repair Clamps
Adjustable to 3/8"-3/4" I.P.S., 1/2" - 1" copper. Includes nuts, bolts, and gasket. Plastic mechanical plug designed to hold higher pressures.  Used for plugging open ended piping as protection from dirt, dust, or debris. Maximum allowed air is 5 PSIG Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI.
B and K 160-607 Pipe Repair Clamps Simmons 11/4X1/2 Pump Cup B and K 160-703 Pipe Repair Clamps
Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder. Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI.
B and K 160-704 Pipe Repair Clamps Lambro 218 Flexible Dryer Vent Hose B K Industries 160-003HC Compression Couplings
Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Lambro Dryer Vent Hose, Flexible, 4 in Nominal, 20 ft Length, Vinyl, White Hydroformed steel body, rubber compression gasket, and metal friction ring, rated up to 125 PSI at 210 degrees F., iron pipe size for piping or repairs on galvanized pipe.
UL 110224 Flexible Foil Duct M-D Building Products 02394 Pipe Wrap Tape American Valve P600CTS 1 CPVC Fitting
UL 181, Class 1 air connector label for general venting. Multiply design of metalized polyester with 1" pitch steel wire support. Polyvinyl chloride foam with aluminum shell that reflects heat. Adhesive closed-cell foam insulates and protects. For use in general piping applications,using copper tube sized pipe. Easy to operate for instant emergency piping. Piping must be restrained
Simmons 2X11/4 Pump Cup Simmons 2X5/8 Pump Cup B and K 160-705 Pipe Repair Clamps
Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder. Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder. Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI.
B and K 160-706 Pipe Repair Clamps Simmons 8385L Standard Water Well Pump Valve B K Industries 160-004HC Compression Couplings
Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Waterproof impregnated lower valve for regular service. Hydroformed steel body, rubber compression gasket, and metal friction ring, rated up to 125 PSI at 210 degrees F., iron pipe size for piping or repairs on galvanized pipe.
Simmons 3X2 Pump Cup B and K 160-707 Pipe Repair Clamps Simmons 3X1/2 Pump Cup
Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder. Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder.
B and K Industries 160-005HC Compression Coupling B and K 160-708 Pipe Repair Clamps Simmons 450-5 Relief Valve
Hydroformed steel body, rubber compression gasket, and metal friction ring, rated up to 125 PSI at 210 degrees F., iron pipe size for piping or repairs on galvanized pipe. Provides positive seal on leaking pipes, type 430 stainless steel, max operating temperature  - 167 degrees F. Rated up to 150 PSI. Cast brass finish. Pressure only relief valve. Factory preset at 75 psi.
Homebasix F-0645 Clip-On Oscillating Portable Fan Lambro 219L Flexible Dryer Vent Hose Lambro 215L Flexible Dryer Vent Hose
Personal clip-on/table fan, 6 in., 2 speed energy saving motor. Mounts easily on a desk or table. 90 (degree) full room oscillation. 120 (degree) vertical tilt. Powder-coated safety grill. Optional base. Lambro Dryer Vent Hose, Flexible, 4 in Nominal, 50 ft Length, Vinyl, White Lambro Dryer Vent Hose, Flexible, 3 in Nominal, 50 ft Length, Vinyl, White
B and K 160-006HC Compression Couplings Simmons 31/2X21/4 Pump Cup B and K 160-007HC Compression Couplings
Hydroformed steel body, rubber compression gasket, and metal friction ring, rated up to 125 PSI at 210 degrees F., iron pipe size for piping or repairs on galvanized pipe. Plastic and wax impregnated oak-tan leather cups for regular service. No.3X2 - Use with #2 Pitcher Pump for 3" Cylinder. No.31/2X21/4 - Use with #3 Pitcher Pump for 31/2" Cylinder. Hydroformed steel body, rubber compression gasket, and metal friction ring, rated up to 125 PSI at 210 degrees F., iron pipe size for piping or repairs on galvanized pipe.
B and K Industries 160-008HC Compression Coupling Simmons 1161 Plunger Assembly Eastman 60248 Dual Outlet Washing Machine Outlet Box
Hydroformed steel body, rubber compression gasket, and metal friction ring, rated up to 125 PSI at 210 degrees F., iron pipe size for piping or repairs on galvanized pipe. For No.22368A pump. Complete with rod. 3/4" MHT outlet, UPC
Eastman 60245 Dual Outlet Washing Machine Outlet Box Eastman 60243 Dual Outlet Washing Machine Outlet Box Eastman 60244/38937 Washing Machine Outlet Box With Valve
3/4" MHT outlet, UPC 3/4" MHT outlet, UPC Right or left side drain, 1/4 Turn ball valve installed. 1/2"CPVC
Lambro 1790 Dryer Outlet Boxes Watts WPWME-1 Washing Machine Outlet Box With Valve UL 181 Flexible Foil Duct
12" x 20" dryer wall box. Prevents duct from being crushed, Flame resistant material, fits between studs and is a space saver. Includes wall  unit and wall trim plate. Comes complete with two individual 1/4-turn brass valves and white protective enclosure with faceplate. Valves are fitted for standard washing machine hose and 1/2" WaterPEX CrimpRing fittings. Design allows for left, center or right valve and waste mounting. The 6-1/2 x 7-5/8" x 3" enclosure comes complete with brackets for nailing to house framing. (Hoses sold separately). UL 181, Class 1 air connector label for general venting. Multiply design of metalized polyester with 1" pitch steel wire support.
Oatey Quadtro 38529/38934 Washing Machine Outlet Box Oatey Quadtro 38568/38822 Washing Machine Outlet Box Oatey Quadtro 38528 Washing Machine Outlet Box
Quadtro quarter-turn valves, copper sweat. Can be used in commercial or residential applications which require supply valve and waste drain recessed into the wall. Versatile design allows for right, left, or center drain and bottom or top mount valves. Easily installed and removed test cap does not fall into drain. 2" drain opening fits PVC or ABS Sch 40 DWV pipe. 1/4 turn brass ball valve. Copper sweat. Box made of high impact polystyrene, 4 support brackets included for mounting. Snap-on faceplate frame accomodates up to 1 in. drywall. Easy to remove knockout. Quadtro single lever ball valve, copper sweat. Can be used in commercial or residential applications which require supply valve and waste drain recessed into the wall. Versatile design allows for right, left, or center drain and bottom or top mount valves. Easily installed and removed test cap does not fall into drain. 2" drain opening fits PVC or ABS Sch 40 DWV pipe. single lever valve. Copper sweat. Box made of high impact polystyrene, 4 support brackets included for mounting. Snap-on faceplate frame accomodates up to 1 in. drywall. Easy to remove knockout. Quadtro 1/4-turn valves, 1/2" ASTM F1807 PEX.. Can be used in commercial or residential applications which require supply valve and waste drain recessed into the wall. Versatile design allows for right, left, or center drain and bottom or top mount valves. Easily installed and removed test cap does not fall into drain. 2" drain opening fits PVC or ABS Sch 40 DWV pipe. 1/4 turn brass ball valve. Box made of high impact polystyrene, 4 support brackets included for mounting. Snap-on faceplate frame accomodates up to 1 in. drywall. Easy to remove knockout.
WASHER OUTLET BOX 1/4 TURN    Sharkbite EB75 Pressure Regulating Valve Watts LFN45B Pressure Reducing Valve
The Quadtro Push Connect washing machine outlet box is the ultimate solution for installation flexibility.  Makes joining copper, CVPC or PEX pipe simple and fast without soldering, crimping, or solvent welding.  Includes disconnect tool.  Allows for right, left, or center drain and bottom or top mount valves. Compact iron-body pressure reducing and regulating valve designed for installations where small size and economy are important, and where local codes allow the use of iron body regulators for water service. Intended for use where supply line inlet pressure does not exceed 300 psi. Suitable for either cold or hot water service. Ideal for domestic installations, it automatically reduces and regulates inlet pressure down to the standard factory setting of 45 psi. Features inbuilt back-pass check and fully pressure-balanced piston. NPT threaded female union inlet x NPT female outlet. Compact, versatile, bronze body construction, with built-in strainer and bypass. For residential and light-duty commercial water pressure regulating. Integral stainless steel strainer, removable when bottom plug is removed. Replaceable seat module, serviceable inline. 33 to 180 degrees Fahrenheit temperature range. 400 psi max working pressure. 50 psi standard reducing pressure, adjustable 25 to 75 psi. Bypass feature controls thermal expansion pressure until inlet pressure is above 150 psi. Meets requirements of ASSE Standard 1003 (ANSI A112.26.2); IAPMO Listed.
Sharkbite EB45 Pressure Regulating Valve Sharkbite EB45 Pressure Regulating Valve Sharkbite EB45 Pressure Regulating Valve
Half-cartridge based pressure reducing and regulating valve with bronze body. Assembled using the double union nuts with the special sharkbite fittings. Sharkbite fittings can be used on copper, PEX and CPVC. Supplied by factory with a standard delivery setting of 45 psi. Can be adjusted fro 10-70 psi without changing the spring. Intended for use where supply line pressure does not exceed 200 psi. Suited for either cold or hot water service. Features compact pressure reducing and regulating valves, Certified by ASSE Standard1003, Listed by IAPMO and ASSE, By-pass mechanism integral with the cartridge, Instant push-fit connections. Half-cartridge based pressure reducing and regulating valve with bronze body. Supplied by factory with a standard delivery setting of 45 psi. Outlet pressure can be adjusted from 10-70 psi without changing the spring. Intended for use where supply line pressure does not exceed 400 psi. Suited for either cold or hot water service. Features: Compact pressure reducing and regulating valves, certified to ASSA Standard 1003 and listed by IAPMO and ASSE, By-pass mechanism integral with the cartridge. Half-cartridge based pressure reducing and regulating valve with bronze body. Supplied by factory with a standard delivery setting of 45 psi. Outlet pressure can be adjusted from 10-70 psi without changing the spring. Intended for use where supply line pressure does not exceed 400 psi. Suited for either cold or hot water service. Features: Compact pressure reducing and regulating valves, certified to ASSA Standard 1003 and listed by IAPMO and ASSE, By-pass mechanism integral with the cartridge.
Simmons 1160 Pitcher Pump Sharkbite EB45 Pressure Regulating Valve FAN WALL MOUNT 18IN
Designed for rugged, long life service, all parts are made from close grain cast iron for optimum strength. All bolt lugs are reinforced for maximum strength. Cap can be adjusted for a wide range of handle positions. Base tapped for 1-1/4" pipe connection. If handle is left in up position and no foot valve is listed, entire pump will drain-prevents freezing. Half-cartridge based pressure reducing and regulating valve with bronze body. Supplied by factory with a standard delivery setting of 45 psi. Outlet pressure can be adjusted from 10-70 psi without changing the spring. Intended for use where supply line pressure does not exceed 400 psi. Suited for either cold or hot water service. Features: Compact pressure reducing and regulating valves, certified to ASSA Standard 1003 and listed by IAPMO and ASSE, By-pass mechanism integral with the cartridge. Can be wall-mounted or a hanging fan where floor space is limited, when overhead circulation is required and for harsh indoor environments. Features totally enclosed, dust proof, energy efficient PSC motor - 120 volt, 60Hz and 0.7 Amps. Pull chain, rugged hanging bar and head tilts 180 degrees. OSHA compliant rust resistant grilles and 6 foot grounded 3-prongs power cord. Made of powder-coated steel.
Space-Saving Hvb 4924 High Velocity Blower Fan Sharkbite EB25 Pressure Regulating Valve Maxxair IF18 Exhaust Fan
Streamlined body. Ultra quiet motor. Easy-to-use top mounted controls. Directional louvers for precision air delivery. Optional oscillation for broad room coverage. Easy grip carry handle. Fully assembled for immediate use. ETL Listed. Stainless steel body, orange twist-cap eliminates need for wrench adjustment, numerical indicator show pressure without the need of a gauge, single piece cartridge can be removed with valve body remaining in place, Outlet pressure range: 20-90 psi, Maximum temperature: 180 degrees F., Maximum initial pressure: 300 psi. Designed for barns, greenhouses, and other heavy duty applications. PSC energy efficient thermally protected motors. Flange has pre-drilled holes for easy installation. Rolled flange edges for handling protection during installation. Balanced 4-blade fan assembly totally enclosed for protection & OSHA compliance. Integrated, precision-formed exterior shutters are draft-free. Shutters open and close automatically. Housing constructed of durable 20-gauge galvanized steel. Removable interior grille. OSHA compliant grille. May be used with the adjustable thermostat with Firestat (Model No. XXADJTSTAT). 1-year limited warranty.
Maxxair IF24 Exhaust Fan Maxxair IF36 Exhaust Fan CEILING FAN INDUSTRIAL 96IN
Designed for barns, greenhouses, and other heavy duty applications. PSC energy efficient thermally protected motors. Flange has pre-drilled holes for easy installation. Rolled flange edges for handling protection during installation. Balanced 4-blade fan assembly totally enclosed for protection & OSHA compliance. Integrated, precision-formed exterior shutters are draft-free. Shutters open and close automatically. Housing constructed of durable 20-gauge galvanized steel. Removable interior grille. OSHA compliant grille. May be used with the adjustable thermostat with Firestat (Model No. XXADJTSTAT). 1-year limited warranty. Designed for barns, greenhouses, and other heavy duty applications. PSC energy efficient thermally protected motors. Flange has pre-drilled holes for easy installation. Rolled flange edges for handling protection during installation. Balanced 4-blade fan assembly totally enclosed for protection & OSHA compliance. Integrated, precision-formed exterior shutters are draft-free. Shutters open and close automatically. Housing constructed of durable 20-gauge galvanized steel. Removable interior grille. OSHA compliant grille. May be used with the adjustable thermostat with Firestat (Model No. XXADJTSTAT). 1-year limited warranty. Silent operation with reduced motor noise. Includes remote control and convenient wall holder for storage. 6 inch standard downrod length. 9 blade design for high volume air movement and aerodynamic blade tip covers. Reversible direction for changing seasonal needs. Energy Star Certified and ETL Listed.
   
 
1