Home > HEATING & COOLING > HEAT & AIR CONDITIONING > DUCT WORK > REGISTER BOOTS / STACKS
Sort By:
1
Anderson Metal 757001-0402 Insert Fittings Anderson Metal 757001-0202 Insert Fittings Anderson Metal 757014-04 Insert Fittings
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Draintech 0440SDB Round Drain Grate Anderson Metal 756108-02 Brass Pipe Cap Anderson Metal 757001-0602 Insert Fittings
Use with pipe and connecting fittings where a drain basin is not needed, or where space doesn't allow the use of a basin. Use with corrugated singlewall pipe, triplewall pipe, leach pipe, or PVC pipe. ADA compliant. Dual Wall, SDR 35, 2729 S&D One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Anderson Metal 756108-04 Brass Pipe Cap Anderson Metal 757014-06 Insert Fittings Anderson 756116-02 Street Pipe Elbow
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Anderson Metal 757014-05 Insert Fittings Anderson Metal 757001-0404 Insert Fitting Anderson Metal 757014-03 Insert Fittings
Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Anderson Metal 756108-06 Brass Pipe Cap Anderson Metal 757001-0604 Insert Fittings NDS 0633SD Corrugated Drain Fittings
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. NDS Universal Plug Adapter, 6 in Length
Anderson Metal 738108-04 Brass Pipe Cap Anderson Metal 738108-02 Brass Pipe Cap Anderson Metal 738108-06 Brass Pipe Cap
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Draintech 0440SDG Round Drain Grate Anderson Metal 757001-0804 Insert Fittings Anderson Metal 757001-0606 Insert Fitting
Use with pipe and connecting fittings where a drain basin is not needed, or where space doesn't allow the use of a basin. Use with corrugated singlewall pipe, triplewall pipe, leach pipe, or PVC pipe. ADA compliant. Dual Wall, SDR 35, 2729 S&D Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Anderson 756116-04 Street Pipe Elbow PIPE DWV SCH40 1-1/2X4FT      Anderson Metal 738108-08 Brass Pipe Fittings
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Anderson Metal 757014-08 Insert Fittings Anderson Metal 757001-0806 Insert Fitting Anderson Metal 757014-10 Insert Fittings
Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Draintech 0642SDB Square Drain Grate NDS 1245 Corrugated Drain Fittings Anderson Metal 757001-1006 Insert Fittings
Made of highest quality structural foam polyethylene with UV inhibitor. May be used in turf or concrete applications such as lawn areas, walkways, patios and pool areas where effective surface water removal systems are required. Grates fit directly into Sewer & Drain pipe or fittings, and Corrugated pipe without the use of a coupling. Not for use in areas subject to vehicular traffic. Fits 6" corrugated single wall and dual pipe, SDR 35, 2729 S&D and Triple Wall pipe. 18.9 sq.in. open surface area. 1/4" grate opening. 0-60 PSI. (BLACK) Can also be used with 6" round catch basins. ADA COMPLIANT. Fits 3" x  4" corrugated pipe, 3" & 4" S/D pipe and 4" SDR35 pipe. Offset allows for adjusting inlet height. Adapters fit 9 x 9, 12 x 12, 18 x 18, 24 x 24 catch basins, and all low profile series. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Genova 700 Cellular Core Solvent Weld Dwv Pipe Cardel 1/2X2 Copper Tubing PIPE DWV SCH40 2X4FT
PIPE DWV SCH40 2X4FT
Our Price: $4.77
Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Anderson Metal 738108-12 Brass Pipe Fitting Genova 700 Cellular Core Solvent Weld Dwv Pipe Anderson 738116-04 Street Pipe Elbow
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Anderson 738116-02 Street Pipe Elbow Anderson 738116-06 Street Pipe Elbow Genova 700 Pipe
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665).
Anderson Metal 757001-0808 Insert Fittings Draintech 0443SDB Atrium Drain Grate Cardel 1/2X2 Copper Tubing
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Use with pipe and connecting fittings where a drain basin is not needed, or where space doesn't allow the use of a basin. Use with corrugated singlewall pipe, triplewall pipe, leach pipe, or PVC pipe. Dual Wall, SDR 35, 2729 S&D Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Anderson Metal 757001-1208 Insert Fittings Anderson Metal 757001-1212 Insert Fitting Anderson 756116-06 Street Pipe Elbow
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Anderson Metal 757001-0608 Insert Fitting Anderson Metal 757001-1008 Insert Fitting Anderson 738116-08 Street Pipe Elbow
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Cardel 3/4X2 Copper Tubing Mueller ProLine Compact Pattern Standard Port Gate Valve Anderson Metal 738108-16 Brass Pipe Cap
Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, solder ends comply with ANSI B16.18, certified to NSF 61. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Genova 700 Pipe Mueller ProLine Compact Pattern Standard Port Gate Valve NDS 1243 Storm Drain Fittings
Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665). Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61. Use to attach 3" or 4" pipe to any size NDS drain basin where a straight-line connection is needed. Works as a locking fitting to 3" or 4" Corrugated Pipe; as a snuggle fitting to 3" or 4" PVC or leach pipe. Manufactured using rigid, lightweight polyolefins.
Fernco FSDP-EO Storm Drain Fitting Fernco FSDP-EC Storm Drain Fitting NDS 0663SDG Round Atrium Grate With UV Inhibitor
Fernco FSDP-EC End Cap
Our Price: $8.44
End outlet slides into the female end of the channels. It also has tabs to fit into the male end of the channels or the cut-to-length end of the channels. End outlet accommodates 3" & 4" sewer and drain pipe or 3" & 4" Sch. 40 fitting hub. The StormDrain Plus end cap slides into the female end of the channels. It also has tabs to fit into the male end of the channels or the cut-to-length end of the channels. Made of highest quality structural foam polyethylene with UV inhibitor. For use in all areas of vegetation and trees. Use in non-traffic areas where lawn mowers are excluded. 6" fits 6" S/ D pipe fittings, 6" bell end, 6" corrugated and 6" catch basins. Open surface area 23.91 sq.in. 5/16" grate opening. D, SDR 35, 2729 S&D Triple wall.
Anderson Metal 757001-0302 Insert Fittings Mueller ProLine Full Port Gate Valve Genova 700 Cellular Core Solvent Weld Dwv Pipe
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Full port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases.
PIPE DWV SCH40 3X4FT          Imperial GV0704-C Standard Straight Back Wall Register Boot Cardel Industries 1/2X5 Copper Tubing
PIPE DWV SCH40 3X4FT
Our Price: $9.13
Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 gauge. Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Bestair A10 Water Pad Mueller ProLine Compact Pattern Standard Port Gate Valve Mueller ProLine Compact Pattern Standard Port Gate Valve
Sturdy metal construction, replace at least once per season. Replacement Furnace Water Pad fits Aprilaire 110, 220, 500, 550, 550A, 558 (10); BestAir BA3200G; Desert Spring DSP-PFT; Hamilton 12HF (EP037); Thermolec 500/550/Pro 600; Evolution Air Pro3000; Honeywell HE100A, HE150A, HE220A/B, HE225A/B; Lasko 5000L, 5000EC, 6000, Lennox WB2-12, WB212; Chippewa 220. Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61. Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, solder ends comply with ANSI B16.18, certified to NSF 61.
DUCT ANGLE BOOT 3-1/4X10X4IN  Mueller ProLine Full Port Gate Valve Anderson 738116-12 Street Pipe Elbow
Used for right-angle transition from round pipe or insulated flexible duct to a register or grille. Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type1, class 150 lb. specification, solder ends comply with ANSI B16.18, certified to NSF 61-G. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Cardel 3/4X2 Copper Tubing Cambridge-Lee 1/2X10M Type M Water Tube NDS ProGuard Gate Valve
Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards.
NDS ProGuard Gate Valve NDS 0660SDB Round Grate NDS 1241 Draintech Corrugated Drain Fittings
PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. Use with 6" round basin, 6" corrugated singlewall pipe, or 6" PVC pipe. ADA compliant. Fits 3" and 4" corrugated pipe; S&D pipe and 4" SDS35 pipe. Fits 9", 12" and 18" catch basins.
Anderson Metal 757001-0304 Insert Fittings Genova 700 Cellular Core Solvent Weld Dwv Pipe Imperial GV0705-C Standard Straight Back Wall Register Boot
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 gauge.
Imperial GV0699-C Standard Straight Back Wall Register Boot NDS 101 Single Outlet Round Catch Basin NDS 201 Double Outlet Round Catch Basin
Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 gauge. Designed to act as sump areas to collect debris and help keep pipe lines unclogged. Single and double outlets will fit 3" & 4" S/D pipe, 3" & 4" corrugated, SDR 35 and 4" DWV pipe. Universal outlet adapter included. Designed to act as sump areas to collect debris and help keep pipe lines unclogged. Single and double outlets will fit 3" & 4" S/D pipe, 3" & 4" corrugated, SDR 35 and 4" DWV pipe. Universal outlet adapter included.
Genova 700 Cellular Core Solvent Weld Dwv Pipe Imperial GV0626-C Wall Register Boot BOOT REGISTER UNIV 3.25X10X6IN
Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. Used for right-angle transition from round pipe or insulated flexible duct to a register or grille. Used for in-line transition from round pipe or insulated flexible duct to a register or grille. 30 gauge.
Imperial GVO621-C Wall Register Boot Imperial GV0627-C Wall Register Boot Imperial GV2451 Wall Stack Boot
Used for right-angle transition from round pipe or insulated flexible duct to a register or grille. Used for right-angle transition from round pipe or insulated flexible duct to a register or grille. Wall Stack Boot, 10 in Width x 3-1/4 in Depth, 6 in Collar, 90 deg, Galvanized
Imperial GV2450 Straight Back Wall Register Boot Genova 700 Solvent Weld Dwv Pipe Bestair A35 Water Pad
Imperial Wall Register Boot, Straight Back, 10 in Width X 3 in Depth, 6 in Collar, Galvanized Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665). Sturdy metal construction. Replace at least once per season. Replacement Furnace Water Pad fits Aprilaire 350, 360, 560, 560A, 568, 600, 700, 760, 760A, 768 (35);  Honeywell HE200A, HE250A, HE260 A/B, HE265A/B, ME360, HE360A/B, HE365A/B; Lennox WB2-17, WB2-17A, WP2-18,WP2-18A.
NDS ProGuard Gate Valve NDS ProGuard Gate Valve PIPE DWV SCH40 4X4FT
PIPE DWV SCH40 4X4FT
Our Price: $12.31
PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards.
Marshall 6EPS Trench Drain End Plate Mueller ProLine Full Port Gate Valve Mueller ProLine Compact Pattern Standard Port Gate Valve
Pieces sold individually. Refer to the following item numbers: 131-9110 6 x 12 inch Steel Bottom with Grate, 192-6930 6 x 48 inch Steel Bottom with Grate, 017-7618 6-3/4 x 7 inch Steel End Plate and 130-0508 6-3/4 x 7 inch Steel End Plate with hole. Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type 1, class 150 lb. specifications, threaded ends comply with ANSI B1.20.1, certified to NSF 61. Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61.
Imperial GV0667-C Center Wall Register Boot Bestair A10W Water Pad DUCT ANGLE BOOT 3-1/4X10X6IN
Used for right-angle center-end transition from round pipe or insulated flexible duct to a register or grille. Metal reinforced paper construction. Replace at least twice per season. High Output Water Pad fits Aprilaire 110, 220, 500, 550, 550A, 558 (10); BestAir BA3200G; Desert Spring DSP-PFT, Hamilton 12HF (EP037); Thermolec 500/550/Pro 600; Evolution Air Pro3000; Honeywell HE100A, HE150A, HE220A/B, HE225A/B; Lasko 5000L, 5000EC, 6000, Lennox WB2-12, WB212; Chippewa 220. Used for right-angle transition from round pipe or insulated flexible duct to a register or grille.
Marshall 6EPSWH Trench Drain End Plate Cardel Industries 1/2X5 Copper Tubing Anderson Metal 757001-0504 Insert Fittings
Pieces sold individually. Refer to the following item numbers: 131-9110 6 x 12 inch Steel Bottom with Grate, 192-6930 6 x 48 inch Steel Bottom with Grate, 017-7618 6-3/4 x 7 inch Steel End Plate and 130-0508 6-3/4 x 7 inch Steel End Plate with hole. Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
NDS 0902SDB Square Grate With UV Inhibitor Protect Plus G24201 Hammock Roll Air Filter Bestair G13 Water Pad
Made of highest quality structural foam polyethylene with UV inhibitor. May be used in turf or concrete applications such as lawn areas, walkways, patios and pool areas where effective surface water removal systems are required.. Fits 9 x 9 catch basin and 9 x 9 low profile. 27.29 sq.in. open surface area. 5/16" grate opening. 61-175 PSI. ADA compliant. Blue/white rigid fiberglass with light lamination on downstream side. Designed for residential, light industrial and commercial applications. Fits General Furnace Humidifier Models: 709, 990, 1040, 1042, 1137, SL16 (990-13); Hamilton Model: 10HF (EP036); and Williamson Power Model: 500.
Cardel Industries 3/4X5 Copper Tubing Anderson 738116-16 Street Pipe Elbow Genova 600 Solvent Weld Dwv Pipe
Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Specially made to be used inside a 2" x 4" stud wall construction for drain-waste-vent applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. Meets ASTM 2949.
Cambridge-Lee 1/2X10L Type L Water Tube Mueller ProLine Standard Port Gate Valve Mueller ProLine Full Port Gate Valve
Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Non-rising stem, six-point cast-iron handle, compression ends for solderless connection to copper tubing, certified to NSF 61. Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type1, class 150 lb. specification, solder ends comply with ANSI B16.18, certified to NSF 61-G.
Genova 700 Pipe Genova 700 Dwv Cut Pipe NDS 422G Pop-Up Drain Emitter With Elbow and UV Inhibitor
Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665). Used for drain, waste, and vent applications. Allows water to be diverted and released to water-safe areas away from structures, erosion-prone landscapes and poor drainage areas. Opened by the hydrostatic pressure of water flowing through the drain pipe, the emitter closes as flow diminishes preventing debris and rodents from entering drain system. 4" polyolefin pop-up emitter, center drive pop-up with UV inhibitor, PVC 90 degree elbow with 1/4" drain hole. 40GPM.
Bestair A35W Water Pad NDS ProGuard Gate Valve NDS ProGuard Gate Valve
Replacement furnace humidifier high output water pad. Paper design with metal support. Replace at least twice per season. Fits Aprilaire Models: 350, 360, 560, 560A, 568, 600, 700, 760, 760A, 768 (35);  Honeywell HE200A, HE250A, HE260 A/B, HE265A/B, ME360, HE360A/B, HE365A/B; Lennox WB2-17, WB2-17A, WP2-18,WP2-18A. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards.
Genova 700 Solvent Weld Dwv Pipe Cambridge-Lee 3/4X10M Type M Water Tube Genova 700 Cellular Core Solvent Weld Dwv Pipe
Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665). Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases.
NDS 0903SDG Atrium Grate With UV Inhibitor Mueller ProLine Full Port Gate Valve Anderson Metal 757002-0606 Insert Fittings
Made of highest quality structural foam polyethylene with UV inhibitor. For use in all areas of vegetation and trees. Use in non-traffic areas where lawn mowers are excluded. Fits 9" x 9" catch basin No.0906SD2, 0909SD4 and 9" x 9" low profile adapter. No. 0906SD. 26.38 sq.in. open surface area, 1/4"  grate opening. Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type 1, class 150 lb. specifications, threaded ends comply with ANSI B1.20.1, certified to NSF 61. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Anderson Metal 757002-0604 Insert Fittings Anderson Metal 757002-0404 Insert Fittings Namasco GALV-1/2 Steel Pipe
One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only.
Imperial GV0060-C Short Way Wall Stack Elbow Fernco FSDP-QUAD Storm Drain Fitting Anderson Metal 757002-0406 Insert Fittings
Used to change the horizontal direction of two sections of rectangular stack duct. 30 gauge. Slides into the female end of the channels. It also has tabs to fit into the male end of the channels or the cut-to-length end of the channels.?The Quad allows left or right hand extension of the StormDrain Plus or even T and X configurations. The required openings are easily cut out. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Mueller ProLine Compact Pattern Standard Port Gate Valve NDS 0909SD2 2-Hole Square Catch Basin Anderson Metal 757002-0804 Insert Fittings
Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61. A diverse selection of catch basins is available to solve any drainage problem and are used because the larger sump areas are suitable when runoff may contain debris. Two way opening. ] One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Anderson Metal 757002-0504 Insert Fittings NDS ProGuard Gate Valve NDS ProGuard Gate Valve
One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards.
Patton HAPF30ATPDQ-U4 Air Replacement Filter Patton HAPF30AOPDQ-U4 Odor Eliminator Air Replacement Filter Genova 700 Dwv Cut Pipe
HEPA - type technology removes up to 99% of airborne pollutants. Traps and Locks 30% more dust and particles from your home. Contains Arm and Hammer baking soda for odor elimination. 10x the odor fighting power for eliminating unpleasant household odors such as tobacco, smoke, pet odors, dirty laundry and cooking fumes. Uniquely formulated blend of Carbon, Zeolite and Arm and Hammer baking soda for superior and effective odor eliminating results. Used for drain, waste, and vent applications.
Anderson Metal 757002-0202 Insert Fittings Protect Plus G30201 Hammock Roll Air Filter Cardel 3/4X5 Copper Tubing
One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Blue/white rigid fiberglass with light lamination on downstream side. Designed for residential, light industrial and commercial applications. Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Anderson Metal 757001-0506 Insert Fittings Anderson Metal 757001-0406 Insert Fittings Cardel Industries 1/2X20M Copper Tubing
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Protect Plus G36201 Hammock Roll Air Filter Mueller ProLine Standard Port Gate Valve Mueller ProLine Compact Pattern Standard Port Gate Valve
Blue/white rigid fiberglass with light lamination on downstream side. Designed for residential, light industrial and commercial applications. Non-rising stem, six-point cast-iron handle, compression ends for solderless connection to copper tubing, certified to NSF 61. Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61.
Anderson Metal 757001-0204 Insert Fittings Anderson Metal 738108-32 Brass Pipe Fitting Mueller ProLine Full Port Gate Valve
Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type 1, class 150 lb. specifications, threaded ends comply with ANSI B1.20.1, certified to NSF 61.
Genova 700 Cellular Core Solvent Weld Dwv Pipe Anderson Metal 757002-0806 Insert Fittings Genova 700 Pipe
Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665).
Namasco GALV-3/4 Steel Pipe Imperial GV0092-C Wall Stack Elbow Namasco .25X10G Steel Pipe
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Used to change the verticall direction of two sections of rectangular stack duct. 30 gauge. Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only.
NDS ProGuard Gate Valve NDS ProGuard Gate Valve NDS 1212SD2 2-Hole 2-Way Square Catch Basin
PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. A diverse selection of catch basins is available to solve any drainage problem and are used because the larger sump areas are suitable when runoff may contain debris. Two way opening. ]
Namasco .375X10G Steel Pipe Cambridge-Lee 3/4X10L Type L Water Tube Anderson Metal 757001-0408 Insert Fittings
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D.
Namasco GALV-1 Steel Pipe Anderson Metal 757020-0604 Insert Fittings Genova 700 Dwv Pipe
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases.
Cardel Industries 1/2X20L Copper Tubing Draintech 1202SDB Drain Grate Genova 700 Dwv Cut Pipe
Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Made of highest quality structural foam polyethylene with UV inhibitor. May be used in turf or concrete applications such as lawn areas, walkways, patios and pool areas where effective surface water removal systems are required. Not for use in areas subject to vehicular traffic. Fits 12 x 12 catch basin series and 12 x 12 low profile adapters. 51.79 sq.in. open surface area. 5/16" grate opening. 61-175 PSI. ADA compliant. Used for drain, waste, and vent applications.
Anderson Metal 757002-0608 Insert Fittings Genova 700 Solvent Weld Dwv Pipe Mueller ProLine Full Port Gate Valve
One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665). Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type 1, class 150 lb. specifications, threaded ends comply with ANSI B1.20.1, certified to NSF 61.
Anderson Metal 757002-0808 Insert Fittings Mueller ProLine Compact Pattern Standard Port Gate Valve Genova 700 Dual Pressure/Drain Waste Vent Pipe
One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Standard port, non-rising stem, six-point cast-iron handle, brass wedge disk, threaded ends comply with ANSI B1.20.1, certified to NSF 61. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665).
Patton HAPF60-U3 Carbon Remover Air Replacement Filter Anderson Metal 757002-0506 Insert Fittings Cardel Industries 3/4X20M Copper Tubing
Powerful carbon filter enhanced with Arm & Hammer backing soda. Cannot be used independently of the main purifier filter. Use with Holmes Purifier: HAP9726B-U. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Genova 700 Cellular Core Solvent Weld Dwv Pipe NDS ProGuard Gate Valve NDS ProGuard Gate Valve
Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards. PVC construction. Gray color body with red handle. EPDM O-rings. Complies with all applicable ASTM and ANSI standards.
Namasco GALV 1/2 Steel Pipe Anderson Metal 757001-0812 Insert Fittings Namasco 1.25X10G Steel Pipe
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Barb x male pipe. One piece brass. Use with plastic tubing or rubber hose. Intended for use with hose clamp or crimp type ferrule. +32 degrees to 200 degrees F. temperature range. Barbed edges provide positive connection. Excellent vibration resistance. Barb size is hose I.D. Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only.
Genova 700 Dwv Cut Pipe Patton HAPF600DM Enhanced Mold Fight Air Replacement Filter Genova 700 Solvent Weld Dwv Pipe
Used for drain, waste, and vent applications. True HEPA filtration helps Remove 99.97% of Airborne Allergens. Enhanced mold fighting power,  ideal for allergy sufferers. Captures allergens and pollutants such as mold, dust, dust mites, debris, pet dander and smoke. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665).
Genova 70042FB DWV Pipe Genova 700 Solvent Weld Dwv Pipe Mueller ProLine Full Port Gate Valve
Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665). Full port, non-rising stem, screw over bonnet, five-point cast-iron handle, solid wedge disk, meets MSS SP-80, type 1, class 150 lb. specifications, threaded ends comply with ANSI B1.20.1, certified to NSF 61.
Cardel Industries 01075 Copper Tubing Namasco 1.5X10G Steel Pipe Genova 70042B DWV Pipe
Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665).
Namasco GALV 3/4 Steel Pipe Fernco FSDP-CHGG Storm Drain Fitting Cardel Industries 3/4X20L Copper Tubing
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. StormDrain Plus ensures a long-lasting, permanent solution to the collection and dispersal of standing surface water. Easy installation. Ideal for dirveways, pools, patios, walkways, sports courts, and more. UV inhibited. Grates are ADA and heel-guard compliant. No clips or screws required. 39.5" L Used for plumbing and heating in commercial applications and residential multi-stories. Can also use for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage.
Anderson Metal 738108-20 Brass Pipe Fitting Cardel Industries 01082 Copper Tubing Frost King F1524 Open Cell Air Filter
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Air Conditioner foam filter.  Removes dust and pollen from the air.  Washable and re-usable.  Can be cut to any size with ordinary scissors
Namasco 2X10G Steel Pipe PURIFIER AIR HEPA HOLMES AER1 Namasco GALV 1 Steel Pipe
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Works with all aer1 filters including: Total Air,  Allergen Remover,  Odor Eliminator, Smoke Grabber and Performance Plus. Dual position design for convenient tabletop placement. Optional ionizer, filter Service Indicator. Recommended for small rooms, up to 111 sq ft. Smoke CADR: 72. Filter: 1 x HAPF30. Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only.
Protect Plus 0120301 Air Filter Filtrete HEPA Plus FAPF02 Replacement Filter Genova 700 Solvent Weld Dwv Pipe
Rigid, self-supporting, latex coated organic material with scrim backing. Fits practically any furnace/air conditioning system. Trims with household scissors. Reusable. Vacuum or wash as needed. Replacement filter. Approximate 3-month life. Solvent weld, use for drain-waste-vent applications, or with pressure fittings for pressure pipe applications. Lightweight, high-impact resistant, and corrosion-proof, resistant to all waste system liquids and gases. PSI ratings at 73 degrees Fahrenheit range from 180 (6" pipe) to 330 (1-1/2" pipe) depending on ID size. Dual rated for pressure (ASTM D1785) and drainage (ASTM D2665).
Cardel Industries 01095 Copper Tubing Imperial GV0213 Wall Stack PURIFIER AIR 3-SPEED HEPA
Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Used between wall studs for venting, heating & air conditioning supply & return duct. True HEPA filtration removes up to 99.97-percent of airborne allergens such as pollen, dust, mold, pet dander and smoke from the air passing through it. Washable pre-filter captures larger particles. Optional ionizer assists in particle removal. Filter life monitor alerts you when filter changes are needed to maintain maximum performance. Recommended for rooms up to 150 square-feet (8-feet by 10-feet). Smoke CADR: 100.
Namasco GALV 11/4 Steel Pipe PURIFIER AIR HEPA TOWER HOLMES Namasco GALV 11/2 Steel Pipe
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. Works with all aer1 filters including: Total air,  Allergen Remover,  Odor Eliminator, Smoke Grabber and Performance Plus. Slim design and integrated handle allow flexibility in placing the unit throughout the home.  Optional ionizer, filter Service Indicator. Recommended for medium rooms, up to 223 sq ft. Smoke CADR: 144. Filter: 2 x HAPF30. Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only.
Cardel 01108 Copper Tubing Fernco FSDP-GP3G Storm Drain Garage Protect Plus AL11524.25 Air Filter
Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. StormDrain Plus ensures a long-lasting, permanent solution to the collection and dispersal of standing surface water. Grates are ADA andheel-guard compliant. UV inhibited. No clips or screws required. Contractor Pack contains: 3 pieces of grey channel with grate, 1 end cap & 1 end outlet. 39.5" L Filter media pad can be easily cut to fit any window or wall mounted room air conditioner. Made completely from expanded aluminum mesh. Can be washed and re-used several times.
Namasco GALV 2 Steel Pipe PURIFIER AIR TRUE HEPA CONSOLE Marshall 6TDSG4 Trench Drain Steel Grate
Standard weight, coupled and threaded for steam and water working pressure up to 150 pounds. Ordered by the length only. True HEPA Filtration removes 99.97% of airborne allergens from the air that passes through the filter. Arm & Hammer enhanced pre-filter for odor control. Progress Bar: Green LED: Filter is working effectively. Yellow LED: Time to purchase a new filter. Red LED: Time to replace the filter. Digital display with auto off timer. Recommended for medium rooms, up to 299 sq. ft. Smoke CADR: 193. Filter: 2 x HAPF600M. Pieces sold individually. Refer to the following item numbers: 131-9110 6 x 12 inch Steel Bottom with Grate, 192-6930 6 x 48 inch Steel Bottom with Grate, 017-7618 6-3/4 x 7 inch Steel End Plate and 130-0508 6-3/4 x 7 inch Steel End Plate with hole.
Cardel Industries 01115 Copper Tubing True Blue PG11524.25 Air Filter
Used for general-purpose residential plumbing to run water line from service entrance through house or building to bathrooms, kitchen sinks, etc. Adhere to local plumbing codes for installation/usage. Washable/3 year life, rigid self-supporting.  Made in the USA!
   
 
1