Home > HEATING & COOLING > HEAT & AIR CONDITIONING > AIR CONDITIONERS > PORTABLE AIR CONDITIONERS
Sort By:
1
Pro-Flex PFIM-0001 Pro-Flex Installation/Training Guide Anderson Metal 756103-02 Brass Pipe Coupling Anderson Metal 756103-04 Brass Pipe Coupling
All installers must purchase and read the Installation/ Training Guide and return the qualified installer card on the back cover to Pro-Flex, LLC. All installations must be performed by a qualified person recognized by the local jurisdiction as capable of performing such work. AMC Pipe Coupling, Barstock, 1/8 in Nominal Size, Threaded, Brass AMC Pipe Coupling, Barstock, 1/4 in Nominal Size, Threaded, Brass
Anderson 756116-02 Street Pipe Elbow Mueller ProLine In-Line Check Valve Mueller ProLine In-Line Check Valve
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Fits both schedule 40 and 80 pipes, spring-loaded poppet, stainless steel spring, O-ring seal, solvent ends comply with ASTM D2466. Not for use with compressed air. Fits both schedule 40 and 80 pipes, spring-loaded poppet, stainless steel spring, O-ring seal, solvent ends comply with ASTM D2466. Not for use with compressed air.
Pro-Flex PFSP-0302 Pro-Flex Striker Plate Anderson Metal 750097-0604 Brass Flare  Adapter Anderson 750066-0606 3-Piece Tubing Coupling
Protective devices required where tubing passes through structural members. Anderson Tube Adapter, 1/4 x 3/8 in Nominal Size, Compression, Brass Three piece construction - nut, sleeve, and body. Use with copper, brass, aluminum, or plastic tubing. -65 degrees F. to +250 degrees F. temperature range. Easy to disassemble, no flaring tool required. Primary uses water, gasoline, oil, and vacuum lines. UPC individually bagged.
Anderson 750066-0302 3-Piece Reducing Tubing Coupling Pro-Flex Floppy-Flex Protective Conduit Anderson Metal 756103-06 Brass Pipe Coupling
Three piece construction - nut, sleeve, and body. Use with copper, brass, aluminum, or plastic tubing. -65 degrees F. to +250 degrees F. temperature range. Easy to disassemble, no flaring tool required. Primary uses water, gasoline, oil, and vacuum lines. UPC individually bagged. 12" long floppy-flex galvanized protective conduits for CSST tubing. AMC Pipe Coupling, Barstock, 3/8 in Nominal Size, Threaded, Brass
Anderson 756116-04 Street Pipe Elbow Anderson 756100-02 Pipe Elbow Anderson Metal 738103-04 Brass Pipe Fitting
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Anderson Pipe Elbow, Series: 756100-02, 1/8 in Nominal, FIP End, 90 deg, 1000 psi Working, Brass, Yellow, 250 deg F, Federal Public Law 111-380 AMC Pipe Coupling, 1/4 in Nominal Size, FPT, Brass
Anderson 738100-04 Pipe Elbow Anderson 738100-06 Pipe Elbow Anderson Metal 738103-06 Brass Pipe Coupling
Anderson Pipe Elbow, Series: 738100-04, 1/4 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, ASME B16.15, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water Anderson Pipe Elbow, Series: 738100-06, 3/8 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, ASME B16.15, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water AMC Pipe Coupling, 3/8 in Nominal Size, FPT, Brass
Anderson 738100-02 Pipe Elbow Anderson Metal 738103-02 Brass Pipe Coupling KBI DF-0750-T Chemical Resistant Drum Faucet
Anderson Pipe Elbow, Series: 738100-02, 1/8 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, ASME B16.15, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water AMC Pipe Coupling, 1/8 in Nominal Size, FPT, Brass 3/4"MPT polyethylene drum faucet. Low friction bearing surface allows for easy open and close. Bulk.
Anderson Metal 756101-02 Brass Pipe Tee BREAKER VACUUM BRASS 3/4INCH  Mueller ProLine In-Line Check Valve
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2  turns past finger tight. Female pipe three ends. SharkBite Vacuum Breaker, 3/4 in, Female x Male End Connection, Brass Body, 180 Deg F, Use On Homes, Schools, Laboratories or Any Commercial Building Fits both schedule 40 and 80 pipes, spring-loaded poppet, stainless steel spring, O-ring seal, solvent ends comply with ASTM D2466. Not for use with compressed air.
Pro-Flex PFSP-0307 Pro-Flex Striker Plate Anderson Metal 738103-08 Brass Pipe Fittings Pro-Flex Floppy-Flex Protective Conduit
Protective devices required where tubing passes through structural members. AMC Pipe Coupling, 1/2 in Nominal Size, FPT, Brass 12" long floppy-flex galvanized protective conduits for CSST tubing.
B&K 108-904RP Backflow Preventer Vacuum Breaker Anderson Metal 738101-06 Brass Pipe Fitting Anderson Metal 738101-04 Brass Pipe Fitting
Fits any 3/4'' hose thread outlet. Prevents back siphoning of contaminated water, protection for portable hoses connected to hose thread faucets. Break-off attachment screw for permanent installation with no plumbing changes. Hose threads comply with ANSI B1.20.7; ASSE 1019 approved, UPC, Canadian UPC approved. Anderson Pipe Tee, 3/8 in Nominal Size, FPT, Brass Anderson Pipe Tee, 1/4 in Nominal Size, FPT, Brass
SC125B Sump Check Valve Anderson Metal 750097-0806 Brass Adapter Anderson 750066-0406 3-Piece Tubing Coupling
Durable sonic welded thermo-plastic body. Anderson Tube Adapter, 1/2 x 3/8 in Nominal Size, Compression, Brass Three piece construction - nut, sleeve, and body. Use with copper, brass, aluminum, or plastic tubing. -65 degrees F. to +250 degrees F. temperature range. Easy to disassemble, no flaring tool required. Primary uses water, gasoline, oil, and vacuum lines. UPC individually bagged.
Anderson 738116-04 Street Pipe Elbow Anderson 738116-02 Street Pipe Elbow Anderson 738116-06 Street Pipe Elbow
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Anderson 738100-08 Pipe Elbow Brass Craft CSSTNN-16N Gas Appliance Connectors NDS 107 Standard Round Valve Box With Overlapping ICV Cover
Anderson Pipe Elbow, Series: 738100-08, 1/2 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Durable plastic construction with snap-in green plastic lid. No. RVB-1 - Top 6", Bottom 8". No. RVB-2 - Top 10", Bottom 13-1/8". CSA approved.
Anderson 756116-06 Street Pipe Elbow Anderson Metal 738103-12 Brass Pipe Fittings Anderson Metal 738101-08 Brass Pipe Fitting
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. AMC Pipe Coupling, 3/4 in Nominal Size, FPT, Brass Anderson Pipe Tee, 1/2 in Nominal Size, FPT, Brass
B&K 108-904 Silcock Vacuum Breaker Brass Craft CSSTNN-22N Gas Appliance Connectors Anderson 738116-08 Street Pipe Elbow
Fits any 3/4'' hose thread outlet. Prevents back siphoning of contaminated water, protection for portable hoses connected to hose thread faucets. Break-off attachment screw for permanent installation with no plumbing changes. Hose threads comply with ANSI B1.20.7; ASSE 1019 approved, UPC, Canadian UPC approved. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
Brass Craft CSSTNN-28N Gas Appliance Connectors Anderson 738100-12 Pipe Elbow NDS flo Control 1011 Reinforced Poppet Check Valve
Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Anderson Pipe Elbow, Series: 738100-12, 3/4 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, ASME B16.15, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back pressure. Reinforced Poppet.. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. KC-1500-S and KC-2000-S are UL recognized spa component.
NDS flo Control 1001 Reinforced Poppet Check Valve Abbott Rubber 9001P-200 Lightweight Non-Toxic Tubing Mueller ProLine In-Line Check Valve
Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back  pressure. Reinforced Poppet. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. For use with compression fittings. Made from non-toxic, odorless, tasteless ingredients that meet FDA requirements. Natural in color, light weight, and resistant to stress cracking, it forms a solid barrier to gases, vapor, and moisture. Fits both schedule 40 and 80 pipes, spring-loaded poppet, stainless steel spring, O-ring seal, solvent ends comply with ASTM D2466. Not for use with compressed air.
Sta-Rite FP0026-6D-P2 Sump Pump Check Valve B&K 109-204 Self-Closing Drum and Barrel Faucet PlumbPak PP855-21 Tubing
Double-threaded for use with 1-1/4" or 1-1/2" sump pump discharges, Discharge side designed to allow discharge hose to clamp directly in place, built-in anti-airlock hole. Zamac construction. Convenient holes to lock handle closed position. For use with all petroleum products, except trichlorethylene. Not for use with detergents or water. 3/4" male pipe thread inlet. Threaded inlets comply with ANSI B1.20.01. 1/4" x 25' poly tubing.
Pro-Flex PFAP-1210 Pro-Flex Accessory Pack NDS flo Control 1011 Reinforced Poppet Check Valve NDS flo Control 1001 Reinforced Poppet Check Valve
Includes: 4 retainer rings,  2 each - slide rings, silicone O-rings, high temperature sealing gaskets. Replacement parts for lost or broken components. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back pressure. Reinforced Poppet.. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. KC-1500-S and KC-2000-S are UL recognized spa component. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back  pressure. Reinforced Poppet. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards.
Mueller ProLine In-Line Check Valve Mueller ProLine Swing Check Valve Anderson Metal 738103-16 Brass Pipe Fitting
Fits both schedule 40 and 80 pipes, spring-loaded poppet, stainless steel spring, O-ring seal, solvent ends comply with ASTM D2466. Not for use with compressed air. Certified to NSF 61 requirements. AMC Pipe Coupling, 1 in Nominal Size, FPT, Brass
Anderson Metal 738101-12 Brass Pipe Fittings VALVE CHCK ABS 1-1/4 RUB BOOT Arrowhead Brass PK1430 Air Vent Assembly Kit
Anderson Pipe Tee, 3/4 in Nominal Size, FPT, Brass Rubber boot inlet and outlet. Full flow design, weighted flapper valve Includes vacuum breaker cap, underbody, o-ring, and plunger. Air vent assembly for Arrowhead frost free hydrants, 420 & 455BFP series.
VALVE CHCK ABS 1-1/2 RUB BOOT Brass Craft CSSTNN-34N Gas Appliance Connectors Anderson 738116-12 Street Pipe Elbow
Rubber boot inlet and outlet. Full flow design, weighted flapper valve Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight.
BrassCraftCSSLNN-10NGasApplianceConnectors SC150SRS Sump Check Valve SC125SRS Sump Check Valve
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Durable sonic welded thermo-plastic body. Durable sonic welded thermo-plastic body.
Pro-Flex PFBC-AB Pro-Flex Bonding Clamps Brass Craft CSSL54-12 Gas Appliance Connectors Mintcraft SRSD06 Round Ceiling Diffuser 6 in W
UL467 bronze bonding clamp. Bonding of the gas system is required with all installations of Pro-Flex CSST. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. White round ceiling diffuser, with 3 pcs screws. 1 pc /shrink with color label.
Brass Craft CSSD54-12 Gas Appliance Connectors Pro-Flex PFAP-3410 Pro-Flex Accessory Pack VALVE CHECK UNIV 1-1/4AND1-1/2
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Includes: 4 retainer rings,  2 each - slide rings, silicone O-rings, high temperature sealing gaskets. Replacement parts for lost or broken components. Includes one universal check valve and two adapters. Made from durable ABS plastic. High quality NItril-Bruna N seal. Fits all: 1-1/4 & 1-1/2 MPT & FPT.
Brass Craft CSSLNN-16N Gas Appliance Connector BrassCraftCSSCNN-22NGasApplianceConnectors BrassCraftCSSLNN-22NGasApplianceConnectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
BrassCraftCSSLNN-28NGasApplianceConnectors Pro-Flex PFMF-1212 Tube To Pipe Adapter Brass Craft CSSLNN-34N Gas Appliance Connector
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Includes all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble to Pro-Flex tubing. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Anderson Metal 738104-04 Brass Pipe Union Anderson Metal 738104-06 Brass Pipe Union Anderson Metal 738104-02 Brass Pipe Fitting
Anderson Pipe Union, 1/4 in Nominal Size, FPT, Brass Anderson Pipe Union, 3/8 in Nominal Size, FPT, Brass Anderson Pipe Union, 1/8 in Nominal Size, FPT, Brass
Anderson 738100-16 Pipe Elbow NDS flo Control 1011 Reinforced Poppet Check Valve NDS flo Control 1001 Reinforced Poppet Check Valve
Anderson Pipe Elbow, Series: 738100-16, 1 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, ASME B16.15, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back pressure. Reinforced Poppet.. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. KC-1500-S and KC-2000-S are UL recognized spa component. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back  pressure. Reinforced Poppet. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards.
Mintcraft SRSD08 Round Ceiling Diffuser 8 in W Brass Craft CSSTNN-46N Gas Appliance Connectors Mueller ProLine Swing Check Valve
White round ceiling diffuser, with 3 pcs screws. 1 pc /shrink with color label. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Certified to NSF 61 requirements.
Anderson Metal 738104-08 Brass Pipe Union Pro-Flex PFFN-1212 Tube To Pipe Adapter B and K Industries G014SS101118RP Gas Connectors
Anderson Pipe Union, 1/2 in Nominal Size, FPT, Brass Includes all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble to Pro-Flex tubing. CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature.
Brass Craft CSSL54-18 Gas Appliance Connectors Brass Craft CSSNN-28N Gas Appliance Connector Anderson Metal 738103-20 Brass Pipe Coupling
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. AMC Pipe Coupling, 1-1/4 in Nominal Size, FPT, Brass
Wayne 66005-WYN Check Valve Mueller ProLine In-Line Check Valve Brass Craft CSSC21-24 Gas Appliance Connectors
1-1/2" pump thread with 1-1/4" or 1-1/2" pipe connection. Fits both schedule 40 and 80 pipes, spring-loaded poppet, stainless steel spring, O-ring seal, solvent ends comply with ASTM D2466. Not for use with compressed air. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSL54-36 Gas Appliance Connectors Brass Craft CSSL54-24 Gas Appliance Connectors Brass Craft CSSCNN-16N Gas Appliance Connector
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
NDS 111BC Standard Round Valve Box With Overlapping ICV Cover Brass Craft CSSD54-18 Gas Appliance Connectors Brass Craft CSSD54-24 Gas Appliance Connectors
Durable plastic construction with snap-in green plastic lid. No. RVB-1 - Top 6", Bottom 8". No. RVB-2 - Top 10", Bottom 13-1/8". CSA approved. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Anderson Metal 750086-0610 Brass Compression Adapter Brass Craft CSSC21-18 Gas Appliance Connectors Honeywell CT30A Economy Heat Manual Thermostat
Use with copper, aluminum, or plastic tubing for water, gas, oil, and vacuum lines in a -65 to 250-degree temperature range. Easy to disassemble, no flaring tool required. UPC individually bagged. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Easy to install and use, adjust the temperature by moving the lever up or down. Dual temperature scale degree F/C. Decorative backplate included to cover wall marks. Works with the following 24-volt systems: furnace (warm air), hot water, steam or gravity and gas fireplaces.
Anderson 738116-16 Street Pipe Elbow Brass Craft CSSD54-24P Procoat Anderson Metal 738101-16 Brass Pipe Fitting
One piece construction. Use with brass or steel pipe. All pipe threads are "American Standard Taper Pipe Threads." Fair vibration resistance. Used in low to medium pressure applications. Teflon tape or pipe sealant is recommended. Pipe threads should be tightened 2 1/2 turns past finger tight. Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. Anderson Pipe Tee, 1 in Nominal Size, FPT, Brass
Brass Craft CSSD54-30 Gas Appliance Connectors Brass Craft CSSL54-30 Gas Appliance Connectors Pro-Flex PFMF-3406 Tube To Pipe Adapter
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Includes all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble to Pro-Flex tubing.
Anderson 738100-20 Pipe Elbow Anderson Metal 738104-12 Brass Pipe Fittings Brass Craft CSSTNN-58N Gas Appliance Connectors
Anderson Pipe Elbow, Series: 738100-20, 1-1/4 in Nominal, FIP End, 90 deg, 200 psi Working, Brass, Rough, 150 deg F, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water Anderson Pipe Union, 3/4 in Nominal Size, FPT, Brass Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Brass Craft CSSL54-36P Procoat Gas Dryer Connectors Sta-Rite Industries FP0026-10 Flotec Brass Craft CSSC21-30 Gas Appliance Connector
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Prevents water backflow into sump basin.  Accept 1-1/4" or 1-1/2" discharge lines.  Corrosion-resistant construction.  Non-threaded, in-line check valve with rubber sleeve and hose clamps. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
NDS flo Control 1011 Reinforced Poppet Check Valve NDS flo Control 1001 Reinforced Poppet Check Valve Brass Craft CSSC21-36 Gas Appliance Connectors
Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back pressure. Reinforced Poppet.. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. KC-1500-S and KC-2000-S are UL recognized spa component. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back  pressure. Reinforced Poppet. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSD54-36 Gas Appliance Connectors Spartan 20010 Lightweight Flexible Pipe Brass Craft CSSLNN-46N Gas Appliance Connector
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Lightweight, low pressure, manufactured from selected resins and designed specifically for non-critical applications such as open-end drain line. Use for farm/ranch water systems, electrical or cable TV conduit, construction, city service lines, sprinkler systems, skating rinks, air conditioning, submersible pumps, etc. NOT TO BE exposed to direct sunlight for extended periods. NOT FOR USE For Compressed Air Systems. Use with insert fittings and stainless steel clamps. Working pressures based on PSI at 73.4 degrees Fahrenheit. At higher temperatures working pressure is less. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Brass Craft CSSL54-24P Procoat Gas Dryer Connectors Brass Craft CSSCNN-46N Gas Appliance Connectors Anderson Metal 738103-24 Brass Pipe Fitting
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. AMC Pipe Coupling, 1-1/2 in Nominal Size, FPT, Brass
Pro-Flex PFFN-3406 Tube To Pipe Adapter Wayne 57028-001 Check Valve Kit With Rubber Boot and Metal Collars Brass Craft CSSL54-48 Gas Appliance Connector
Includes all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble to Pro-Flex tubing. Includes: Two convertible fittings and four hose clamps. Durable thermoplastic valve body and poppet designed to resist corrosion and to stop noise. Handles either 1-1/4" or 1-1/2" OD pipe. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Pro-Flex PFBC-CDEA Pro-Flex Bonding Clamps NDS flo Control 1011 Reinforced Poppet Check Valve NDS flo Control 1001 Reinforced Poppet Check Valve
UL467 bronze bonding clamp. Bonding of the gas system is required with all installations of Pro-Flex CSST. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back pressure. Reinforced Poppet.. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. KC-1500-S and KC-2000-S are UL recognized spa component. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back  pressure. Reinforced Poppet. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards.
SHOCK ABSORBR SUPPLY MIP 1/2IN Brass Craft CSSD54-48 Gas Appliance Connectors Brass Craft CSSC21-48 Gas Appliance Connectors
Oatey quiet pipes water hammer absorbers are designed to reduce water pipe banging noise caused by quick-closing valves and protect plumbing appliances and fixtures from the effects of water hammer.  Quiet pipes absorbers contain a piston that uses a triple O-ring to maintain 60 psi charge in the tube. When the water valve is shutoff, it sends a shock through the system and the piston compresses.  This absorbs a shock that would normally rattle and shake the pipe. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Mueller 104-511 ProLine Anti-Siphon Frost Free Sillcock Valve Anderson 738100-24 Pipe Elbow Mueller ProLine Swing Check Valve
CSA certified, meets ASSE standard 1019, chrome-plated body and tube, built-in lockshield, heavy-duty six-point cast-iron handle, threaded ends comply with ANSI b1.20.1, ANSI/NSF 61-9 certified, hose threads comply with ANSI B1.20.7, solder ends comply with ANSI B16.18, backflow preventer checks siphoning back into the water supply, automatically drains upon water shut off. Anderson Pipe Elbow, Series: 738100-24, 1-1/2 in Nominal, IPT End, 90 deg, Brass, Federal Government S.3874, Federal Public Law 111-380, FixAll AB 1953, For Potable Water Certified to NSF 61 requirements.
Brass Craft CSSD54-48P Procoat Abbott Rubber 9002P Lightweight Non-Toxic Tubing Mueller 104-403 ProLine Frost Free Sillcock Valve
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. For use with compression fittings. Made from non-toxic, odorless, tasteless ingredients that meet FDA requirements. Natural in color, light weight, and resistant to stress cracking, it forms a solid barrier to gases, vapor, and moisture. 1/2'' MIP x 1/2'' Sweat. Heavy chrome plated brass, silver soldered construction. Notched flange for stable installation. Chrome plated casting and tube, lockshield, 3/4" hose thread outlet, heavy cast iron handle. Pipe threads comply with ANSI B1.20.1, hose threads comply with ANSI B1.20.7, solder connections comply with ANSI B16.18. CSA certified ANSI/NSF 61-9. UPC Coded. Bulk handy carton.
Brass Craft CSSL54-48P Procoat Honeywell CG-511 Small/Medium Thermostat Guard Cover DIFFUSER CEILING ROUND 6IN WHT
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Fits over existing thermostat. Fits all Honeywell and most other thermostats. Clear plastic cover resist yellowing. Key lock with inner shelf to prevent tampering. For wall and ceiling applications. Fully adjustable air-flow. Includes mounting collar. Made of polypropylene. Can be used as a supply or exhaust air diffuser.
Sharkbite U2008-0000LFA Straight Check Valve Mueller 104-513 ProLine Anti-Siphon Frost Free Sillcock Valve Brass Craft CSSD54-36P Procoat
General purpose spring check valve that prevents the reverse flow of water. Can be installed horizontally and vertically and can be connected in seconds to copper tubing, CTS, CPVC, and Pex. Instant push-fit connections for increase ease of use - no soldering, clamps, unions, or glue required. Maximum Pressure: 200 PSI. Maximum Temperature: 150 degrees F (65 degrees C) (water). CSA certified, meets ASSE standard 1019, chrome-plated body and tube, built-in lockshield, heavy-duty six-point cast-iron handle, threaded ends comply with ANSI b1.20.1, ANSI/NSF 61-9 certified, hose threads comply with ANSI B1.20.7, solder ends comply with ANSI B16.18, backflow preventer checks siphoning back into the water supply, automatically drains upon water shut off. Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor.
Brass Craft CSSLNN-58N Gas Appliance Connectors Brass Craft CSSD54-60 Gas Appliance Connectors Mueller 104-404 ProLine Frost Free Sillcock Valve
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. 1/2'' MIP x 1/2'' Sweat. Heavy chrome plated brass, silver soldered construction. Notched flange for stable installation. Chrome plated casting and tube, lockshield, 3/4" hose thread outlet, heavy cast iron handle. Pipe threads comply with ANSI B1.20.1, hose threads comply with ANSI B1.20.7, solder connections comply with ANSI B16.18. CSA certified ANSI/NSF 61-9. UPC Coded. Bulk handy carton.
Brass Craft CSSC21-36P Procoat Gas Range Connectors Honeywell CT31A Economy Heat/Cool Manual Thermostat Brass Craft CSSC21-48P Procoat Gas Range Connectors
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings. 24-volt heating and air conditioning systems. Low voltage control of gas or oil heating and cooling equipment. Bimetal temperature sensor. Snap acting switch (magnetic switch) does not require leveling and is mercury-free. Simple, worry-free operation. Compatible for single stage heating and cooling, Furnace (warm air), central air conditioning, hot water, steam or gravity and gas fireplaces. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings.
BrassCraftCSSCNN-58NGasApplianceConnectors Brass Craft CSSL54-60 Gas Appliance Connectors BrassCraftCSSL44E-24PGasApplianceConnectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Mueller 104-519 ProLine Anti-Siphon Frost Free Sillcock Valve Anderson 750066-0806 3-Piece Reducing Tubing Coupling Anderson Metal 738104-16 Brass Pipe Union
CSA certified, meets ASSE standard 1019, chrome-plated body and tube, built-in lockshield, heavy-duty six-point cast-iron handle, threaded ends comply with ANSI b1.20.1, ANSI/NSF 61-9 certified, hose threads comply with ANSI B1.20.7, solder ends comply with ANSI B16.18, backflow preventer checks siphoning back into the water supply, automatically drains upon water shut off. Three piece construction - nut, sleeve, and body. Use with copper, brass, aluminum, or plastic tubing. -65 degrees F. to +250 degrees F. temperature range. Easy to disassemble, no flaring tool required. Primary uses water, gasoline, oil, and vacuum lines. UPC individually bagged. Anderson Pipe Union, 1 in Nominal Size, FPT, Brass
Mueller 104-405 ProLine Frost Free Sillcock Valve NDS Standard Rectangular Valve Box With Overlapping ICV Cover Brass Craft CSSC54-36P Procoat Gas Range Connectors
1/2'' MIP x 1/2'' Sweat. Heavy chrome plated brass, silver soldered construction. Notched flange for stable installation. Chrome plated casting and tube, lockshield, 3/4" hose thread outlet, heavy cast iron handle. Pipe threads comply with ANSI B1.20.1, hose threads comply with ANSI B1.20.7, solder connections comply with ANSI B16.18. CSA certified ANSI/NSF 61-9. UPC Coded. Bulk handy carton. ICV valve box with overlapping cover, Black/Green.14 In. x 19 In. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings.
Brass Craft CSSC21-60 Gas Appliance Connectors Honeywell CG-512A Large Thermostat Guard Cover Mueller 104-515 ProLine Anti-Siphon Frost Free Sillcock Valve
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Fits over existing thermostat. Fits all Honeywell and most other thermostats. Clear plastic cover resist yellowing. Key lock with inner shelf to prevent tampering. CSA certified, meets ASSE standard 1019, chrome-plated body and tube, built-in lockshield, heavy-duty six-point cast-iron handle, threaded ends comply with ANSI b1.20.1, ANSI/NSF 61-9 certified, hose threads comply with ANSI B1.20.7, solder ends comply with ANSI B16.18, backflow preventer checks siphoning back into the water supply, automatically drains upon water shut off.
Anderson Metals 59540-0612 Oil Drum and Tank Valve DIFFUSER CEILING ROUND 8IN WHT Mueller 104-521 ProLine Anti-Siphon Frost Free Sillcock Valve
3/4" mip x 3/8" flare. For wall and ceiling applications. Fully adjustable air-flow. Includes mounting collar. Made of polypropylene. Can be used as a supply or exhaust air diffuser. CSA certified, meets ASSE standard 1019, chrome-plated body and tube, built-in lockshield, heavy-duty six-point cast-iron handle, threaded ends comply with ANSI b1.20.1, ANSI/NSF 61-9 certified, hose threads comply with ANSI B1.20.7, solder ends comply with ANSI B16.18, backflow preventer checks siphoning back into the water supply, automatically drains upon water shut off.
Anderson 750066-0808 3-Piece Tubing Coupling Honeywell CT410B 4-Wire Manual Thermostat Honeywell CW200A-1032 Winter Watchman
Three piece construction - nut, sleeve, and body. Use with copper, brass, aluminum, or plastic tubing. -65 degrees F. to +250 degrees F. temperature range. Easy to disassemble, no flaring tool required. Primary uses water, gasoline, oil, and vacuum lines. UPC individually bagged. Mechanical, non-programmable thermostat provides 120 - 240 Vac control for baseboard electric heat systems. Provides reliable line voltage control of resistive rated electric heating equipment. Snap-action switch activates heat for positive temperature control. Universal application. Replaces virtually any  four-wire line voltage wall-mounted electric heating thermostat. Rugged, plastic mounting base and one-piece vented cover. Low temperature signal. Turns on light alerting neighbors to low temperatures in an unoccupied home to prevent freezing pipes and other damage. Ranges 35 degrees F. to 60 degrees F. 120 Vac., 120 W.
BrassCraftCSSL44E-36PGasApplianceConnectors Mueller 104-517 ProLine Anti-Siphon Frost Free Sillcock Valve BrassCraftCSSD44E-18PGasApplianceConnectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. CSA certified, meets ASSE standard 1019, chrome-plated body and tube, built-in lockshield, heavy-duty six-point cast-iron handle, threaded ends comply with ANSI b1.20.1, ANSI/NSF 61-9 certified, hose threads comply with ANSI B1.20.7, solder ends comply with ANSI B16.18, backflow preventer checks siphoning back into the water supply, automatically drains upon water shut off. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSC54-48P Procoat Spartan 20020 Lightweight Flexible Pipe Sharkbite U2016-0000LFA Straight Check Valve
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings. Lightweight, low pressure, manufactured from selected resins and designed specifically for non-critical applications such as open-end drain line. Use for farm/ranch water systems, electrical or cable TV conduit, construction, city service lines, sprinkler systems, skating rinks, air conditioning, submersible pumps, etc. NOT TO BE exposed to direct sunlight for extended periods. NOT FOR USE For Compressed Air Systems. Use with insert fittings and stainless steel clamps. Working pressures based on PSI at 73.4 degrees Fahrenheit. At higher temperatures working pressure is less. General purpose spring check valve that prevents the reverse flow of water. Can be installed horizontally and vertically and can be connected in seconds to copper tubing, CTS, CPVC, and Pex. Instant push-fit connections for increase ease of use - no soldering, clamps, unions, or glue required. Maximum Pressure: 200 PSI. Maximum Temperature: 150 degrees F (65 degrees C) (water).
Honeywell RTH111B1016/A Non-Programmable Thermostat PIPE POLY 160LB 1/2IN X 100FT Pro-Flex PFST-12 Pro-Flex Termination Plates
Precise comfort control, consistent comfort to the highest level of accuracy. Easy to read display. Retains setpoint in the event of a power outage. Easy-access battery replacement. Works with heating and cooling system. Does not work with heat pump systems and electric baseboard heat (120-240V). PE4710 high-density, manufactured from selected resins. Use for farm/ranch water systems, electrical or cable TV conduit, construction and excavations, city service lines, mine and industrial drainage, sprinkler systems, irrigation, skating rinks, air conditioning, submersible pumps, etc. NOT TO BE exposed to direct sunlight for extended periods. NOT FOR USE For Compressed Air Systems. Use with insert fittings and stainless steel clamps. Meets or exceeds ASTM-D2239. NSF Approved for drinking water use. Working pressures based on PSI at 73.4 degrees Fahrenheit. At higher temperature working pressure is less. Includes attached fitting complete with all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble to Pro-Flex tubing.
Arrowhead PK1390 Replacement Self-Draining Vacuum Breaker Sta-Rite FP212-257 Flotec Sewage Check Valves Cresline 18205 Flexible Pipe
Replacement self-draining vacuum breaker for Arrowhead frost free hydrant. Fits all models with BFPSD after part number (backflow preventer, self draining) and 485BFP and 486BFP models. Nickel plated. Economy check valve with stainless steel hose clamp fittings. PE4710 high-density, manufactured from selected resins. Use for farm/ranch water systems, electrical or cable TV conduit, construction and excavations, city service lines, mine and industrial drainage, sprinkler systems, irrigation, skating rinks, air conditioning, submersible pumps, etc. NOT TO BE exposed to direct sunlight for extended periods. NOT FOR USE For Compressed Air Systems. Use with insert fittings and stainless steel clamps. Meets or exceeds ASTM-D2239. NSF Approved for drinking water use. Working pressures based on PSI at 73.4 degrees Fahrenheit. At higher temperature working pressure is less.
BrassCraftCSSD44E-24PGasApplianceConnectors Pro-Flex PFTE-BBB6 Tube Tee Mueller ProLine Swing Check Valve
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Includes all components (Retainer Ring, Slide Ring, O-ring, and High Temperature Gasket) required to assemble each branch to Pro-Flex tubing. Certified to NSF 61 requirements.
Cresline 18335 Flexible Pipe BrassCraftCSSC44E-24PGasApplianceConnectors Mueller 104-823HC ProLine Quarter Master Anti-Siphon Sillcock Valve
PE4710 high-density, manufactured from selected resins. Use for farm/ranch water systems, electrical or cable TV conduit, construction and excavations, city service lines, mine and industrial drainage, sprinkler systems, irrigation, skating rinks, air conditioning, submersible pumps, etc. NOT TO BE exposed to direct sunlight for extended periods. NOT FOR USE For Compressed Air Systems. Use with insert fittings and stainless steel clamps. Meets or exceeds ASTM-D2239. NSF Approved for drinking water use. Working pressures based on PSI at 73.4 degrees Fahrenheit. At higher temperature working pressure is less. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. 1/2" MIP & 1/2" Sweat. Quarter turn ceramic cartridge. Drains automatically upon water shut off, if the hose is removed or open. Built-in backflow preventer checks siphoning back into water supply. Heavy chrome plated for appearance and corrosion protection. Notched flange allows stable installation on siding. Lead-free silver solder construction. 3/4" hose thread outlet. Pipe threads comply with ANSI B1.20.1; Hose threads comply with ANSI B1.20.7; Solder ends comply with ANSI B16.18. ASSE 1019-A approved;UPC, IAPMO, CSA certified. Certified to NSF 61.Handy carton: bin box display packaging; each valve has a data tag with installation instructions and is bar-coded for easy identification. Handy carton.
Pro-Flex PFMN-CCB 4-Port Pipe Manifold Pro-Flex PFMN-BBB 4-Port Pipe Manifold Mueller 104-841HC ProLine Quarter Master Anti-Siphon Sillcock Valve
Each manifold has 4 1/2" female (FIP) branches. Each manifold has 4 1/2" female (FIP) branches. 1/2" MPT and PEX connection. Easy quarter turn operation. IAPMO - ANSI/NSF-61 approved. Maximum 125 PSI working pressure. Chrome plated brass ball. Teflon seats. 60% copper alloy brass construction. 3/4" hose thread outlet. Large flow rate. Rust resistant handle. Pipe threads comply with ANSI B1.20.1. Hose threads comply with ANSI B1.20.7. Certified to NSF61, ASSE 1019-A, IAPMO, CSA. Handy carton.
NDS flo Control 1011 Reinforced Poppet Check Valve NDS flo Control 1001 Reinforced Poppet Check Valve Anderson 750066-1008 3-Piece Tubing Coupling
Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back pressure. Reinforced Poppet.. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. KC-1500-S and KC-2000-S are UL recognized spa component. Made of High-Impact PVC type II material. 1/2 pound spring gives positive seal with no back  pressure. Reinforced Poppet. Designed for any system where back flow is not desired. Spas, swimming pools, industrial and irrigation. Complies with all applicable ASTM and ANSI standards. Three piece construction - nut, sleeve, and body. Use with copper, brass, aluminum, or plastic tubing. -65 degrees F. to +250 degrees F. temperature range. Easy to disassemble, no flaring tool required. Primary uses water, gasoline, oil, and vacuum lines. UPC individually bagged.
Brass Craft CSSC12E-36 P Gas Appliance Connectors Mueller 104-825HC ProLine Quarter Master Anti-Siphon Sillcock Valve BrassCraftCSSC44E-36PGasApplianceConnectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. 1/2" MIP & 1/2" Sweat. Quarter turn ceramic cartridge. Drains automatically upon water shut off, if the hose is removed or open. Built-in backflow preventer checks siphoning back into water supply. Heavy chrome plated for appearance and corrosion protection. Notched flange allows stable installation on siding. Lead-free silver solder construction. 3/4" hose thread outlet. Pipe threads comply with ANSI B1.20.1; Hose threads comply with ANSI B1.20.7; Solder ends comply with ANSI B16.18. ASSE 1019-A approved;UPC, IAPMO, CSA certified. Certified to NSF 61.Handy carton: bin box display packaging; each valve has a data tag with installation instructions and is bar-coded for easy identification. Handy carton. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnect