Home > PLUMBING > ROUGH PLUMBING SUPPLIES > GAS SUPPLY LINES > CORRUGATED FLEXIBLE GAS SUPPLY
Choose a sub category:
STYRENE-S&D CAPS STYRENE-S&D CAPS STYRENE-S&D ADAPTERS
STYRENE-S&D ADAPTERS STYRENE-S&D ELBOWS STYRENE-S&D ELBOWS
STYRENE-S&D TEES & WYES STYRENE-S&D TEES & WYES STYRENE-S&D CLEANOUTS & PLUGS
STYRENE-S&D CLEANOUTS & PLUGS STYRENE-S&D STRAINERS STYRENE-S&D STRAINERS
Sort By:
1
Genova S49230 Floor Strainer Genova S45233 Downspout Adapter Harvey's 023015-48 Pipe Joint Compound
Fits into any same size hub to prevent debris from entering a drain opening on the floor. Fits flush into any fitting hub. Conforms to ASTM D2852. Used to connect rain gutter downspouts to underground sewer piping. Conforms to ASTM D2852. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape.
Harvey 030005-144 Pipe Thread Compound Genova S49240 Floor Strainer Oatey 31229 Great White
Pipe thread compound in stick form. Lubricates, seals and prevents rust and corrosion. Use pipe stick on pressures to 2,000 PSI, temperatures to 350 degrees Fahrenheit for metal pipe carrying water, steam, air, ammonia, gasoline, natural gas,  butane, propane, freon, petroleum oil.  DO NOT USE ON OXYGEN SYSTEMS. Fits into any same size hub to prevent debris from entering a drain opening on the floor. Fits flush into any fitting hub. Conforms to ASTM D2852. Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included.
Oatey 30779 All Purpose Pipe Cleaner Rectorseal 55910 PVC/CPVC Primer/Cleaner Oatey 30999 ABS Cement
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications.
Harvey's 029035 Pipe Thread Compound Rectorseal 23710 T-Plus 2 Pipe Thread Sealant Oatey 31012 PVC Cement
Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Oatey 30755 PVC/CPVC Primer Harvey's 018100-24 P-4 Oatey 30890 Rain-R-Shine
A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit.
Plumb Pak PP854-2 Pipe Joint Compound Oatey 30883 PVC Cement Harvey's 019050-24 PVC/CPVC Purple Primer
Plumb Pak Pipe Joint Compound, 2 oz, Tube Packing Medium-bodied gray cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Recommended for potable water, pressure pipe, conduit and DWV. Recommended application temperature 40-110 degrees. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can.
Rectorseal 25790 Pipe Thread Sealant Harvey's 018400-24 PVC Cement Oatey 30780 PVC/CPVC Primer/Cleaner
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Purple-tinted all purpose primer/cleaner for PVC and CPVC pipe and fittings. Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent cement. Purple tint for verification for code. Apply at temperatures 40 degrees Fahrenheit to 100 degrees Fahrenheit.
Oatey 31128 CPVC Pipe and Fitting Cement Harvey's 018450-24 P-6E Oatey 30750 Pipe Primer/Cleaner
Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. For electrical PVC conduit and plumbing PVC applications. Medium bodied, medium set; designed for use on all duct and conduit applications through 6" in diameter. Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified for use in potable water, sewer, drain, and waste and vent systems. UPC listed. Meet requirements of ASTM D-2564. Dauber can. Recommended for use with PVC and CPVC pipe and fittings. Formulated to remove dirt and oil from the surface of the piping, as well as soften the piping in preparation for solvent welding. NSF Standard 61 listed for PW, DWV, and sewer. Meets ASTM standard F 656.
Oatey 30818 All-Purpose Cement Harvey's 018500-24 A-6 Duraspout 45344 Downspout Adapter
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can. Used to connect rain gutter downspouts to underground sewer piping.
Harvey 019100-24 All Purpose Pipe Cleaner Rectorseal 55902 PVC Cement Oatey 30850 PVC Cement
All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Regular body cement specifically formulated for all PVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers, and drain, waste and vent (DWV). For use on PVC pipe through 2" Schedule 40 pressure piping and up to and including 4" Schedule 40 non-pressure (DWV) piping; it may also be used for making up transition joints between ABS and PVC in non-pressure (DWV) piping. Dauber top. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Oatey 31230 Great White Harvey's 018110-24 P-4 Harvey's 018700-24 C-4
Lubricates and seals all threaded joints. White, non-hardening, non-separating, non-toxic paste. Withstands up to 3,000 PSI on gases from -50 to +400 degrees Fahrenheit, and 10,000 PSI on liquids from -50 to +500 degrees Fahrenheit. For use with water, steam, natural and LP gas, oil, caustics or dilute acid lines of PVC, CPVC, ABS, Cycolac, Polypropylene, iron, steel, or copper. NSF and IAPMO listed. Brush included. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Harvey's 018200-24 P-2 PVC Cement Oatey 31129 CPVC Pipe and Fitting Cement Harvey's 018000-24 Mp-6
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Oatey 30917 ABS Cement Oatey 31013 PVC Cement Brass Craft PS1087 Seal 'N Check Kit
Medium-bodied ABS resin in solvent solution formula for use on ABS pipe and fittings up to 6" in diameter. Formulated especially for the hot, arid climates in the western states. Use for all non-pressure applications, for all types and grades of ABS pipe and fittings for DWV. Meets ASTM D-2235. SALES AREA - ONLY IN THE WESTERN REGION. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Pipe thread sealant is used to seal male to female pipe threads. The leak detection solution is applied (poured) on the joints of a gas installation to detect unsafe seals in the component-to-component connections (shut-off valve to adapter to gas connector, and gas connector to adapter to appliance regulator). Bubbles in the solution will indicate a leak. The pipe thread sealant is preferred over gas PTFE tape because of its fluidity - it seals up the crevices of the Male to Female thread engagement and provides a better seal. The leak detection solution does not contain soap or detergents, eliminating a false reading.
Rectorseal 55912 PVC/CPVC Primer/Cleaner Harvey 019110-24 All Purpose Pipe Cleaner Plumb Pak PP854-1 Pipe Thread Sealant
Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Plumb Pak Pipe Thread Sealant, Teflon, 1 oz, Tube Packing
Oatey 30756 PVC/CPVC Primer Oatey 31910 Flow-Guard Gold Harvey's 023030 Pipe Joint Compound
A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape.
Harvey's 025020 Pipe Thread Compound Harvey's 019060-24 PVC/CPVC Purple Primer Harvey 19520 All Purpose Pipe Cleaner
Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Convenient project pack contains 4 oz. all-purpose pipe cleaner, and 4 oz. multi-purpose solvent cement. For most ABS, PVC, or CPVC projects. Twin pack.
Rectorseal 55970 Abs/PVC/CPVC Cement Duraspout 46344 Offset Downspout Adapter Oatey 30900 ABS/PVC Transition Cement
Medium body multipurpose cement formulated for use on all PVC, CPVC and ABS pipe applications such as potable water, conduit and drain, waste and vent (DWV). It is for use on all PVC, CPVC and ABS pipe classes for pressure systems through 2" Schedule 40 and non-pressure piping systems through 6" Schedule 40 (excluding Schedule 80), also for use on transition joints to join PVC to CPVC and PVC to ABS. Exceeds ASTM F 493 specifications and is LEED compliant. Dauber top. Used to connect rain gutter downspouts to underground sewer piping. Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138.
Harvey's 018510-24 A-6 Harvey's 018410-24 PVC Cement Harvey's 018210-24 P-12
Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Oatey 30783 PVC/CPVC Primer/Cleaner Harvey 019120-12 All Purpose Pipe Cleaner Oatey 30821 All-Purpose Cement
Purple-tinted all purpose primer/cleaner for PVC and CPVC pipe and fittings. Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent cement. Purple tint for verification for code. Apply at temperatures 40 degrees Fahrenheit to 100 degrees Fahrenheit. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product.
Oatey 31911 Flow-Guard Gold Oatey 30891 Rain-R-Shine Rectorseal 31631 Tru-Blu
Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Fast drying, adhesive thread sealant especially suited for high vibration environments such as refrigeration or compressor applications. Stays flexible - designed for areas of high vibration and thermal expansion/contraction. Can also be used as a positive lock and seal on threaded fasteners. Lead free and contains no metal. For use with water (hot or cold). Brushable from 20 degree F to 140 degree F. Excellent as a gasket adhesive on flanges. Low odor, non-separating. Lubricates and protects threads. Easy application - brush top applicator. Meets Federal Specification TT-S-1732.
Harvey's 018710-24 C-4 CPVC Cement Oatey 32161 Hot Blue Lava PVC Cement Harvey's 019550 Primer/Cement Pack
Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Convenient project pack contains 4 oz. purple primer, and 4 oz. blue PVC wet set cement. For most wet condition projects. Twin pack.
Rectorseal 55914 PVC/CPVC Primer/Cleaner Harvey's 029048 Pipe Thread Compound Harvey's 018010-24 Mp-6
Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Gray, non-drip paste for pipe joint threads on lines carrying water, steam, air or natural gas. Prevents corrosion to threads. Never hardens, joints separate easily. Contains no lead, non-toxic. Do not apply to plastic threads. Use Harvey's TFE Paste or PTFE Tape made of TEFLON on plastic threaded joints. Brushtop bottle. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Oatey 15420 Pro Dope Harvey's 019530 Primer/Cement Pack Oatey 30246 Primer/Cement Pack
Standard oil-based thread sealant ensures exceptional leak-proof joints. For use on metal pipe and fittings carrying water, natural gas, air, steam, ammonia, brine, diluted acids, and alkalis. Uniform, smooth consistency provides for an easy application; will not drip or spill out of container. Long shelf life. Non-setting formula will not harden, crack or become brittle. Lubricates as it forms a tight pressure seal. Inhibits rust and corrosion. Wipes clean from hands. Withstands air/steam pressure to 200 psi and liquid pressure to 250 psi at temperatures ranging from 0 deg F to 350 deg F. NOT FOR LP GAS. Not for use on plastic pipe or fittings. Certified to ANSI/NSF Standard 61, safe for drinking water lines. Meets Fed. Spec. TT-S-1732. Gray. Convenient project pack contains 4 oz. purple primer and 4 oz. PVC solvent cement. For most PVC pipe projects. Twin pack. Contains one can of  regular clear PVC cement, and one can of NSF purple primer. Ideal size for most pipe installations.
Oatey 30782 All Purpose Pipe Cleaner Oatey 15804 Hercules Pipe Thread Sealant PRIMER CPVC/PURPLE HANDY 4OZ
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Contains 1 can of CPVC Cement and 1 can of NSF Purple Primer.
Harvey's 018120-12 P-4 Harvey's 018220-12 P-2 PVC Cement Oatey 30863 PVC Cement
Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Rectorseal 25631 Pipe Thread Sealant Rectorseal 23631 T-Plus 2 Oatey 31094 PVC Cement
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV.
Harvey's 023045 Pipe Joint Compound Oatey 30925 ABS/PVC Transition Cement Harvey's 025050 Pipe Thread Compound
White thread lubricant and sealant. Brushable paste dries slowly, non-hardening, withstands up to 3000 PSI on gases at temps from -50d F to +500d F. Use on water, steam, natural and LP gas, oils, fuels, dilute acids. Apply to metals, PVC, CPVC, ABS, polypropylene and nylon. All-purpose sealant for HEAVY DUTY applications. Warning: Never use any pipe thread sealant paste or stick on halogens or oxygen; use PTFE Pipe Thread Tape. Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle.
Oatey 31014 PVC Cement Oatey 30812 Bonding Adhesive Oatey 32166 Hot Orange Lava
Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. X-15 PVC bonding adhesive is formulated for use to join two sheets of PVC shower pan liner membrane together. Provides permanent, watertight seal to form larger membrane for use in tile shower or other concealed water-proofing applications. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846.
Harvey's 018720-12 C-4 CPVC Cement Harvey's 018420-12 PVC Cement Harvey's 018020-12 Mp-6
Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Oatey 15427 Pro Dope Harvey's 019070-12 PVC/CPVC Purple Primer Oatey 30834 All-Purpose Cement
Standard oil-based thread sealant ensures exceptional leak-proof joints. For use on metal pipe and fittings carrying water, natural gas, air, steam, ammonia, brine, diluted acids, and alkalis. Uniform, smooth consistency provides for an easy application; will not drip or spill out of container. Long shelf life. Non-setting formula will not harden, crack or become brittle. Lubricates as it forms a tight pressure seal. Inhibits rust and corrosion. Wipes clean from hands. Withstands air/steam pressure to 200 psi and liquid pressure to 250 psi at temperatures ranging from 0 deg F to 350 deg F. NOT FOR LP GAS. Not for use on plastic pipe or fittings. Certified to ANSI/NSF Standard 61, safe for drinking water lines. Meets Fed. Spec. TT-S-1732. Gray. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product.
Oatey 30902 ABS Cement Oatey 15806 Hercules Pipe Thread Sealant Rectorseal 23551 T-Plus 2 Pipe Thread Sealant
Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732.
Harvey's 018320-12 PVC Cement Rectorseal 25551 Pipe Thread Sealant Harvey 019130-12 All Purpose Pipe Cleaner
Fast setting, all-weather, medium bodied PVC solvent cement specifically recommended for cold weather and fast setting pressure applications. Recommended for pressure pipe: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Formulated for fast initial set up at temperatures down to 10 degrees fahrenheit. Effective temperature range -15 degrees to 110 degrees fahrenheit. Meets performance requirements of ASTM D-2564. Dauber can. Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can.
Oatey 30876 PVC Cement Oatey 31121 PVC Cement Oatey 30757 PVC/CPVC Primer
Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656.
Oatey 31132 PVC Cement Oatey 30893 Rain-R-Shine Oatey 31095 PVC Cement
Medium-bodied clear cement for use on PVC pipe and fittings. Up to 6" diameter. Formulated for fast initial set-up at temperatures down to -15 degrees F to 100 degrees F. schedule 40 and schedule 80. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit, and DWV. Non-pressure, DWV, up through 4" diameter: no primer needed where local codes permit. Meets ASTM D-2564. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV.
Oatey 30795 All Purpose Pipe Cleaner Oatey 31015 PVC Cement Harvey's 018130-12 P-4
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Brass Craft CSSD54-24P Procoat Brass Craft CSSL54-36P Procoat Gas Dryer Connectors Harvey's 018230-12 P-12
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Brass Craft CSSL54-24P Procoat Gas Dryer Connectors Harvey's 018030-12 Mp-6 CLEANER CLEAR 32 OUNCE
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface.
Oatey 32162 Hot Blue Lava PVC Cement Oatey 31105 PVC Cement Oatey 30894 Rain-R-Shine
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit.
Oatey 31008 PVC Cement Harvey's 025080 Pipe Thread Compound Oatey 15808 Hercules Pipe Thread Sealant
Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Use on all metals, plastic PVC, CPVC, ABS and nylon threads. Tolerates -50 F to +400 degrees Fahrenheit; gas to 3000 PSI, liquid to 6000 PSI. Soft, slow drying, never seizes, allows easy disassembly. SEALANT for all types of gas lines.  Brushtop bottle. For use on both plastic and metal pipe and fittings. Grit-free and does not contain PTFE (teflon). Sets soft; no cure time required. Never hardens, cracks or becomes brittle. No odor. Non-separating, non-flammable, and non-hazardous. Leak-proof hydraulic resistance to 12,000 psi. Withstands gas pressure to 2,600 psi. Performs over a temperature range of -50 degrees to 400 degrees F (on steel pipe). For use on all metals, including galvanized steel, black iron, aluminum, copper, brass, stainless steel, and on PVC, ABS, and CPVC plastics (for use on specific brands of CPVC pipe, verify suitability with pipe manufacturer). Not recommended for lines carrying concentrated acids, alkalis, ketones, and oxygen. Certified to ANSI/NSF Standard 61; safe for drinking water lines. UPC listed. Meets CSA requirements 4-90 for gas. Meets Fed. Spec. TT-S-1732.
Rectorseal 25431 Pipe Thread Sealant Brass Craft CSSD54-48P Procoat Harvey's 019080-12 PVC/CPVC Purple Primer
Soft-set, slow drying compound seals, lubricates, protects threaded pipe and fittings.  Can be pressurized immediately for piping up through 2" and 100 psi. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, and PVC pipe.  Conforms to TT-S-1932. Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can.
B and K Industries G014YE101136RP Gas Connectors Brass Craft CSSL54-48P Procoat Harvey's 018430-12 PVC Cement
CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can.
Oatey 31122 PVC Cement Brass Craft CSSC22-36P Procoat Oatey 32167 Hot Orange Lava
Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" ID (5/8" OD) tube with fittings. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846.
Brass Craft CSSD54-36P Procoat PRIMER PURPLE 32 OUNCE        Rectorseal 23431 T-Plus 2 Pipe Thread Sealant
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Non-setting, multi-purpose compound contains teflon, plus synthetic fibers.  May be pressurized immediately following application.  Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass reinforced, PVC, CPVC, and ABS pipe. Conforms to TT-1732.
Brass Craft CSSC21-36P Procoat Gas Range Connectors Harvey's 028005-144 Pipe Thread Compound Display Brass Craft CSSC21-48P Procoat Gas Range Connectors
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings. For sealing and lubricating threaded pipe joints. In smooth paste form. For steam, water, air, and natural gas. Does not contain lead. Wipes clean from hands. Hang tab tube. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings.
Oatey 30847 All-Purpose Cement Brass Craft CSSC54-36P Procoat Gas Range Connectors Oatey 31226 Pipe Joint Compound
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings. Fast set non-hardening paste which lubricates and seals threaded joints. Non-toxic; may be used on water, natural gas, steam and air lines. Perfect for applying gaskets to flanges. Not for use on plastic threads.
Brass Craft CSSC22-48P Procoat B and K Industries G014YE101148RP Gas Connectors Brass Craft CSSC54-48P Procoat
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" ID (5/8" OD) tube with fittings. CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings.
Brass Craft CSSL115E-36P Gas Appliance Connector Brass Craft CSSD105E-36P Gas Appliance Connector Brass Craft CSSC91E-48P Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSD54-60P Procoat Brass Craft CSSD105E-48P Gas Appliance Connectors Brass Craft CSSC91E-48P Gas Appliance Connectors
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
   
 
1