Home > PLUMBING > ROUGH PLUMBING SUPPLIES > GAS SUPPLY LINES
Choose a sub category:
CORRUGATED FLEXIBLE GAS SUPPLY FLEXIBLE STAINLESS GAS SUPPLY FLEXIBLE GAS PIPING SYSTEM
Sort By:
1
Genova 400 Sewer and Drain Pipe Cap Genova Products 41840 Styrene Sewer and Drain Fittings Genova 400 Pipe Plug
Used to permanently or temporarily cap pipe. Meets ASTM D2852. Used to form a removable closure for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. Conforms to ASTM D2852. Used to form a removable closure for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. Conforms to ASTM D2852.
Oatey 30779 All Purpose Pipe Cleaner Rectorseal 55910 PVC/CPVC Primer/Cleaner Oatey 30999 ABS Cement
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications.
Oatey 31012 PVC Cement Oatey 30755 PVC/CPVC Primer Harvey's 018100-24 P-4
Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Oatey 30890 Rain-R-Shine Oatey 30883 PVC Cement Harvey's 019050-24 PVC/CPVC Purple Primer
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Medium-bodied gray cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Recommended for potable water, pressure pipe, conduit and DWV. Recommended application temperature 40-110 degrees. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can.
Harvey's 018400-24 PVC Cement Brass Craft CSSTNN-10N Gas Appliance Connector Oatey 30780 PVC/CPVC Primer/Cleaner
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Purple-tinted all purpose primer/cleaner for PVC and CPVC pipe and fittings. Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent cement. Purple tint for verification for code. Apply at temperatures 40 degrees Fahrenheit to 100 degrees Fahrenheit.
Oatey 31128 CPVC Pipe and Fitting Cement Harvey's 018450-24 P-6E Hancor 36-1083TW Hdpe Sewer And Drain Fitting
Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. For electrical PVC conduit and plumbing PVC applications. Medium bodied, medium set; designed for use on all duct and conduit applications through 6" in diameter. Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified for use in potable water, sewer, drain, and waste and vent systems. UPC listed. Meet requirements of ASTM D-2564. Dauber can. Triple-Wall Pipe Tee-Wye, Series: 3000, 4 in Nominal Size, HDPE, ASTM D3350, For Residential Drainage, Sump Pump Outlet, Curtain Drains, Retaining Walls, Irrigation, Downspout Runoff, Foundation/Footer Drainage, Septic Leach Fields, Agricultural drain Outlets, Parks and Golf Courses
Oatey 30750 Pipe Primer/Cleaner Oatey 30818 All-Purpose Cement Harvey's 018500-24 A-6
Recommended for use with PVC and CPVC pipe and fittings. Formulated to remove dirt and oil from the surface of the piping, as well as soften the piping in preparation for solvent welding. NSF Standard 61 listed for PW, DWV, and sewer. Meets ASTM standard F 656. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can.
Harvey 019100-24 All Purpose Pipe Cleaner Rectorseal 55902 PVC Cement Oatey 30850 PVC Cement
All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Regular body cement specifically formulated for all PVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers, and drain, waste and vent (DWV). For use on PVC pipe through 2" Schedule 40 pressure piping and up to and including 4" Schedule 40 non-pressure (DWV) piping; it may also be used for making up transition joints between ABS and PVC in non-pressure (DWV) piping. Dauber top. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Harvey's 018110-24 P-4 Harvey's 018700-24 C-4 Harvey's 018200-24 P-2 PVC Cement
Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Oatey 31129 CPVC Pipe and Fitting Cement Harvey's 018000-24 Mp-6 Oatey 30917 ABS Cement
Medium-bodied, fast setting formula for use on CPVC pipe and tubing with interference fits only. 40 to 110 degrees Fahrenheit optimum temperature. For use on smallest diameter through 6" diameters. Particularly suited to hot water pipe applications up to 200 degrees. Meets ASTM-F-493. NSF, UPC and IAPMO listed. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Medium-bodied ABS resin in solvent solution formula for use on ABS pipe and fittings up to 6" in diameter. Formulated especially for the hot, arid climates in the western states. Use for all non-pressure applications, for all types and grades of ABS pipe and fittings for DWV. Meets ASTM D-2235. SALES AREA - ONLY IN THE WESTERN REGION.
Oatey 31013 PVC Cement Rectorseal 55912 PVC/CPVC Primer/Cleaner Brass Craft CSSTNN-16N Gas Appliance Connectors
Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564. Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Harvey 019110-24 All Purpose Pipe Cleaner Oatey 30756 PVC/CPVC Primer Oatey 31910 Flow-Guard Gold
All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493.
Harvey's 019060-24 PVC/CPVC Purple Primer Harvey 19520 All Purpose Pipe Cleaner Rectorseal 55970 Abs/PVC/CPVC Cement
Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Convenient project pack contains 4 oz. all-purpose pipe cleaner, and 4 oz. multi-purpose solvent cement. For most ABS, PVC, or CPVC projects. Twin pack. Medium body multipurpose cement formulated for use on all PVC, CPVC and ABS pipe applications such as potable water, conduit and drain, waste and vent (DWV). It is for use on all PVC, CPVC and ABS pipe classes for pressure systems through 2" Schedule 40 and non-pressure piping systems through 6" Schedule 40 (excluding Schedule 80), also for use on transition joints to join PVC to CPVC and PVC to ABS. Exceeds ASTM F 493 specifications and is LEED compliant. Dauber top.
Oatey 30900 ABS/PVC Transition Cement Harvey's 018510-24 A-6 Brass Craft CSSTNN-22N Gas Appliance Connectors
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Medium bodied, medium set, ABS solvent cement designed for use on non-pressure ABS pipe and fittings: Schedule 40, Types I & II, up to 6". Apply at temperatures 40 degrees to 110 degrees fahrenheit. NSF certified and UPC listed. Meets requirements of ASTM D-2235. Dauber can. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Harvey's 018410-24 PVC Cement Harvey's 018210-24 P-12 Oatey 30783 PVC/CPVC Primer/Cleaner
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Purple-tinted all purpose primer/cleaner for PVC and CPVC pipe and fittings. Removes surface dirt, grease and grime as well as softens pipe in preparation for solvent cement. Purple tint for verification for code. Apply at temperatures 40 degrees Fahrenheit to 100 degrees Fahrenheit.
Harvey 019120-12 All Purpose Pipe Cleaner Brass Craft CSSTNN-28N Gas Appliance Connectors Oatey 30821 All-Purpose Cement
All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product.
Oatey 31911 Flow-Guard Gold Oatey 30891 Rain-R-Shine Harvey's 018710-24 C-4 CPVC Cement
Medium-bodied CPVC resin in solvent solution formula for copper tube size (CTS) CPVC hot and cold potable water pipe and fittings up to 2" diameter interference fit only and systems up to 180 degrees Fahrenheit. Faster cure time/reduced installation time. May be used without primer where local codes permit. Low VOC with reduced solvent emissions. Exceeds new environmental requirements, meets various California district rules and ASTM F-493. Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Oatey 32161 Hot Blue Lava PVC Cement Harvey's 019550 Primer/Cement Pack Rectorseal 55914 PVC/CPVC Primer/Cleaner
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Convenient project pack contains 4 oz. purple primer, and 4 oz. blue PVC wet set cement. For most wet condition projects. Twin pack. Hi etch primer specifically formulated for all PVC and CPVC pipe applications such as potable water, pressure pipe, gas, conduit, sewers and drain, waste and vent (DWV). Fast acting, hi-etch primer prepares the surfaces for superior bonding strength, purple color ensures easy visual check for complete coverage. For use on all sizes and classes in both Schedule 40 and Schedule 80. NSF approved, LEED compliant, UPC (IAPMO) listed, meets ASTM F 656 specifications. Dauber can.
Harvey's 018010-24 Mp-6 Harvey's 019530 Primer/Cement Pack Oatey 30246 Primer/Cement Pack
Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. Convenient project pack contains 4 oz. purple primer and 4 oz. PVC solvent cement. For most PVC pipe projects. Twin pack. Contains one can of  regular clear PVC cement, and one can of NSF purple primer. Ideal size for most pipe installations.
Oatey 30782 All Purpose Pipe Cleaner PRIMER CPVC/PURPLE HANDY 4OZ  Harvey's 018120-12 P-4
For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. Contains 1 can of CPVC Cement and 1 can of NSF Purple Primer. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Harvey's 018220-12 P-2 PVC Cement Oatey 30863 PVC Cement Oatey 31094 PVC Cement
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV.
Oatey 30925 ABS/PVC Transition Cement Brass Craft CSSTNN-34N Gas Appliance Connectors Oatey 31014 PVC Cement
Medium-bodied, green PVC resin in solvent solution formula for use in joining all schedules of ABS to PVC pipe and fittings up to 6" diameter in non-pressure transition joints. 40 to 110 degrees Fahrenheit recommended application temperature. Meets ASTM D-3138. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
BrassCraftCSSLNN-10NGasApplianceConnectors Brass Craft CSSL54-12 Gas Appliance Connectors Brass Craft CSSD54-12 Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Oatey 30812 Bonding Adhesive Oatey 32166 Hot Orange Lava Brass Craft CSSLNN-16N Gas Appliance Connector
X-15 PVC bonding adhesive is formulated for use to join two sheets of PVC shower pan liner membrane together. Provides permanent, watertight seal to form larger membrane for use in tile shower or other concealed water-proofing applications. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
BrassCraftCSSCNN-22NGasApplianceConnectors BrassCraftCSSLNN-22NGasApplianceConnectors Harvey's 018720-12 C-4 CPVC Cement
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Regular bodied, fast set CPVC solvent cement designed for use on CPVC pipe and fittings: Schedule 80 and Copper Tube Size, CPVC hot and cold water pipe and fittings up to 4" in diameter. Flows freely and provides a thick layer of cement on the pipe. NSF certified for use in potable water, sewer, drain, waste and vent systems. Should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets ASTM F-493. Dauber can.
Harvey's 018420-12 PVC Cement BrassCraftCSSLNN-28NGasApplianceConnectors Harvey's 018020-12 Mp-6
Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can.
Harvey's 019070-12 PVC/CPVC Purple Primer Oatey 30834 All-Purpose Cement Brass Craft CSSLNN-34N Gas Appliance Connector
Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Oatey 30902 ABS Cement Brass Craft CSSTNN-46N Gas Appliance Connectors Harvey's 018320-12 PVC Cement
Medium-bodied black cement for use on all schedules and classes of ABS pipe and fittings up to 6" diameter with interference fit. Lo-VOC solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. For all non-pressure applications. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Fast setting, all-weather, medium bodied PVC solvent cement specifically recommended for cold weather and fast setting pressure applications. Recommended for pressure pipe: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Formulated for fast initial set up at temperatures down to 10 degrees fahrenheit. Effective temperature range -15 degrees to 110 degrees fahrenheit. Meets performance requirements of ASTM D-2564. Dauber can.
B and K Industries G014SS101118RP Gas Connectors Harvey 019130-12 All Purpose Pipe Cleaner Oatey 30876 PVC Cement
CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature. All-purpose pipe cleaner designed to thoroughly clean pipe. Can be used on ABS, CPVC, and PVC pipe and fittings. Apply at temperatures from 40 degrees to 110 degrees fahrenheit. Flows freely and evaporates quickly. Dauber can. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Oatey 31121 PVC Cement Oatey 30757 PVC/CPVC Primer Brass Craft CSSL54-18 Gas Appliance Connectors
Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSNN-28N Gas Appliance Connector Oatey 31132 PVC Cement Brass Craft CSSC21-24 Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Medium-bodied clear cement for use on PVC pipe and fittings. Up to 6" diameter. Formulated for fast initial set-up at temperatures down to -15 degrees F to 100 degrees F. schedule 40 and schedule 80. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit, and DWV. Non-pressure, DWV, up through 4" diameter: no primer needed where local codes permit. Meets ASTM D-2564. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Oatey 30893 Rain-R-Shine Brass Craft CSSL54-24 Gas Appliance Connectors Oatey 31095 PVC Cement
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV.
Brass Craft CSSD54-18 Gas Appliance Connectors Brass Craft CSSL54-36 Gas Appliance Connectors Oatey 30795 All Purpose Pipe Cleaner
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface.
Brass Craft CSSCNN-16N Gas Appliance Connector BrassCraftCSSCNN-34NGasApplianceConnectors Oatey 31015 PVC Cement
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Regular-bodied clear cement recommended for use on PVC pipe and fittings up to 4" for SCH. 40 and up to 2"  for Sch. 80 potable water pressure pipe, gas, conduit, drain waste and vent pipe.  Flows freely. Sets up quickly. Apply at temperature 40 to 110 degrees F.  NSF and UPC listed. Exceeds ASTM D-2564.
Brass Craft CSSD54-24 Gas Appliance Connectors Brass Craft CSSC21-18 Gas Appliance Connectors Harvey's 018130-12 P-4
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Regular bodied, fast set PVC solvent cement designed for use on PVC pressure pipe and fittings up to 4". NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can.
Brass Craft CSSD54-24P Procoat Brass Craft CSSD54-30 Gas Appliance Connectors Brass Craft CSSL54-30 Gas Appliance Connectors
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSTNN-58N Gas Appliance Connectors Brass Craft CSSL54-36P Procoat Gas Dryer Connectors Brass Craft CSSC21-30 Gas Appliance Connector
Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Harvey's 018230-12 P-12 Brass Craft CSSC21-36 Gas Appliance Connectors Brass Craft CSSD54-36 Gas Appliance Connectors
Designed for use on PVC pressure pipe and fittings up to 12". Flows freely and provides a thick layer of cement on the pipe. Helps to fill gaps in larger diameter pipe and loose fitting joints. NSF certified for use in potable water, sewer, and drain, waste and vent systems and should be applied at temperatures 40 degrees to 110 degrees fahrenheit. UPC listed. Meets requirements of ASTM D-2564. Dauber can. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSLNN-46N Gas Appliance Connector Brass Craft CSSL54-24P Procoat Gas Dryer Connectors Brass Craft CSSCNN-46N Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Harvey's 018030-12 Mp-6 CLEANER CLEAR 32 OUNCE        Brass Craft CSSL54-48 Gas Appliance Connector
Medium bodied, medium set multi-purpose cement designed for use on PVC, CPVC, and ABS pipe and fittings: Schedule 40 & 80, Types I & II, up to 6". For potable water, pressure pipe, conduit, drain waste, and vent pipe. Flows freely and provides a thick layer of cement on the pipe and loose fitting joints. Apply at temperatures 40 degrees to 110 degrees Fahrenheit. Dauber can. For plastic pipes and fittings, all Schedules and all diameters. A fast-acting cleaner to remove surface dirt, grease and grime. Flows freely and evaporates quickly. Does not penetrate pipe surface. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Oatey 32162 Hot Blue Lava PVC Cement Oatey 31105 PVC Cement Brass Craft CSSD54-48 Gas Appliance Connectors
Medium-bodied blue cement for use on all schedules and classes of PVC pipe and fittings up to 6" diameter with interference fit. Lo-V.O.C. Solvent Cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. Very fast-setting hot cement formulated for wet conditions and/or quick pressurization and fast installation. Recommended for potable water, sewer and DWV applications. Recommended application temperature 40 Deg F to 110 Deg F. No primer needed on non-pressure DWV, where local codes permit. Meets ASTM D2564. Heavy duty gray cement for use on all schedules and classes PVC pipe and fittings up to 12" diameter with interference fit, up to 18" for non-pressure. Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District 1168/316A or BAAQMD Method 40 and various environmental requirements. Thick formula fills gaps in large diameter pipe and loose fitting joints. Recommended for potable water, pressure pipe, conduit and DWV. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Oatey 30894 Rain-R-Shine Brass Craft CSSC21-48 Gas Appliance Connectors Oatey 31008 PVC Cement
Medium-bodied, fast-setting, colored cement recommended for PVC pipe and fittings up to 6" in diameter. Formulated for wet conditions and/or when quick pressurization and fast installation is needed. For Sch. 40 and Sch. 80 potable water pressure pipe, irrigation, gas, conduit and drain waste and vent pipe. Flows freely and covers with a thicker layer than regular PVC cement. Apply at 40 to 110 degrees Fahrenheit. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Heavy-bodied clear cement for PVC pipe and fittings. Up to 12" diameter for Schedule 40 and Schedule 80. Recommended for ALL grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Helps fill gaps in larger diameter pipe and loose fitting joints. Apply at temperatures 40 degrees Fahrenheit to 110 degrees Fahrenheit. Exceeds ASTM D-2564. NSF and UPC listed.
Brass Craft CSSD54-48P Procoat Harvey's 019080-12 PVC/CPVC Purple Primer B and K Industries G014YE101136RP Gas Connectors
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. Designed to remove gloss, dirt and grease.  Softens and penetrates bonding surfaces of PVC and CPVC pipe and fittings. Recommended for use on high gloss, hard finish bell end pipe or fittings. Apply at temperature from 40 to 110 degrees F. NSF certified. Meets performance requirements of ASTM F-656. Dauber can. CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature.
Brass Craft CSSL54-48P Procoat Harvey's 018430-12 PVC Cement Oatey 31122 PVC Cement
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/4" ID 3/8" OD tube with fittings. Fast setting, medium bodied PVC solvent cement specifically recommended for wet conditions or when quick pressurization is needed. Recommended for pressure pipes: Schedule 40 & 80 Types I & II, up to 6". NSF certified for use in potable water, sewer, drain, waste and vent systems. Effective temperature range is 40 degrees to 110 degrees Fahrenheit. UPC listed. Meets performance requirements of ASTM D-2564. Dauber can. Very heavy-bodied medium-setting gray colored cement for use on PVC pipe and fittings. Up to 18" diameter for Sch. 40 and Sch. 80. Formulated for quick installation of irrigation pipe and fittings. Recommended for all grades and types of PVC pipe and fittings, potable water, pressure pipe, gas, conduit and DWV. Builds up for large diameter installations. Fills gaps in large diameter pipe and loose fitting joints. Recommended application temperature 40 degrees F to 110 degrees F. Meets ASTM D-2564.
Brass Craft CSSC22-36P Procoat Oatey 32167 Hot Orange Lava Brass Craft CSSD54-36P Procoat
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" ID (5/8" OD) tube with fittings. Heavy-bodied orange cement for use on all schedules and classes of CPVC pipe and fittings up to 6? diameter with interference fit. One-step, fast curing cement designed for cut-in applications where limited time is available for down-time.  Lo-V.O.C. solvent cement meets California South Coast Air Quality Management District (SCAQMD) 1168/316A or BAAQMD Method 40 and various environmental requirements. For commercial hot and cold water systems up to 200 DegF. Recommended application temperature 40 Deg F to 110 Deg F. Approved for Flowguard Gold and Corzan CPVC piping systems. Meets ASTM F-493 and ASTM D-2846. Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor.
Brass Craft CSSLNN-58N Gas Appliance Connectors PRIMER PURPLE 32 OUNCE        Brass Craft CSSD54-60 Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. A purple-tinted aggressive primer recommended for use on PVC and CPVC pipe and fittings, all Schedules and diameters. Formulated to remove surface dirt, grease and grime as well as soften the pipe surface to allow for a fast, secure and permanent solvent weld. For use in areas where the code calls for verification that a primer has been used.  Recommended for all PVC and CPVC installations.  NSF listed.  Meets ASTM F-656. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSC21-36P Procoat Gas Range Connectors B and K Industries G014SS101148RP Gas Connectors Brass Craft CSSC21-48P Procoat Gas Range Connectors
Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings. CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings.
BrassCraftCSSCNN-58NGasApplianceConnectors Brass Craft CSSL54-60 Gas Appliance Connectors BrassCraftCSSL44E-24PGasApplianceConnectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Oatey 30847 All-Purpose Cement Brass Craft CSSC54-36P Procoat Gas Range Connectors B and K Industries G038SS101148RP Gas Connectors
Medium-bodied milky clear cement for ABS, PVC, or CPVC up to 6" diameter. Recommended for pipe and fittings schedule 40 and schedule 80, potable water, pressure pipe, gas, conduit, and DWV. Recommended application temperature  40 degrees F to 110 degrees F. Meets performance requirements of ASTM D-2564, D-2235, F-493. Check local codes for acceptability of this product. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings. CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature.
Brass Craft CSSC21-60 Gas Appliance Connectors Brass Craft CSSC22-48P Procoat B and K Industries G014YE101148RP Gas Connectors
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" ID (5/8" OD) tube with fittings. CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature.
BrassCraftCSSL44E-36PGasApplianceConnectors BrassCraftCSSD44E-18PGasApplianceConnectors Brass Craft CSSC54-48P Procoat
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Manufactured without soldered or brazed joints from type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. Uniform coating leaves no gaps and protects against corrosion and leaks.  1/2" I.D. (5/8" O.D.) tube with fittings.
Brass Craft CSSL115E-36P Gas Appliance Connector Brass Craft CSSD105E-36P Gas Appliance Connector Brass Craft CSSC91E-48P Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSD54-60P Procoat BrassCraftCSSD44E-24PGasApplianceConnectors BrassCraftCSSC44E-24PGasApplianceConnectors
Uniform baked-on polymer coating leaves no gaps to resist corrosion and chemicals and protect against leaks. Manufactured without soldered or brazed joints form type 304 stainless steel. Broader face nuts and fittings with smoother connector ends seal with less torque for easy installation. 3/8'' ID (1/2'' OD) with fittings. CSA IAS design certified for gas appliances indoor and outdoor. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSC12E-36 P Gas Appliance Connectors BrassCraftCSSC44E-36PGasApplianceConnectors Brass Craft CSSD105E-48P Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
BrassCraftCSSL47E-24PGasApplianceConnectors Brass Craft CSSD44E-36P Gas Appliance Connectors Brass Craft CSSC91E-48P Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
BrassCraftCSSC12E-48PGasApplianceConnectors BrassCraftCSSL44E-48PGasApplianceConnectors BrassCraftCSSL47E-36PGasApplianceConnectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSC21-72 Gas Appliance Connectors Brass Craft CSSD44E-48 P Gas Appliance Connectors Brass Craft CSSB22-36 Gas Appliance Connectors
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSD44E-60P Gas Appliance Connectors BrassCraftCSSC44E-48PGasApplianceConnectors Brass Craft CSSB22-60 Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
   
 
1