Home > PLUMBING > ROUGH PLUMBING SUPPLIES > VALVES > YARD HYDRANTS
Choose a sub category:
HDPE-S&D ELBOWS HDPE-S&D TEES & WYES
Sort By:
1
Genova 400 Sewer and Drain Pipe Cap Genova Products 41840 Styrene Sewer and Drain Fittings Genova 400 Pipe Plug
Used to permanently or temporarily cap pipe. Meets ASTM D2852. Used to form a removable closure for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. Conforms to ASTM D2852. Used to form a removable closure for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. Conforms to ASTM D2852.
Genova 41629 PVC Sewer-Drain Fitting Genova 400 Sanitary Street Pipe Elbow Genova 400 Short Turn Pipe Elbow
Solvent welds into fitting hub and adapts to male threaded plug for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. 3" meets ASTM D2949 or exceeds ASTM D2729; 4" and 6" meet ASTM D3034. Used to change direction in piping for sewer lines, septic tank and seepage systems. Sometimes called an street eighth bend. Conforms to ASTM D2852. Used to change direction in piping. Sometimes called a "short turn quarter bend." Meets ASTM D2852.
Brass Craft CSSTNN-10N Gas Appliance Connector Genova Products 41639 PVC Sewer and Drain Cleanout Adapter Brass Craft CSSTNN-16N Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Solvent welds into fitting hub and adapts to male threaded plug for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. 3" meets ASTM D2949 or exceeds ASTM D2729; 4" and 6" meet ASTM D3034. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Brass Craft CSSTNN-22N Gas Appliance Connectors Brass Craft CSSTNN-28N Gas Appliance Connectors Genova Products 41640 PVC Sewer and Drain Cleanout
Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Solvent welds into fitting hub to provide access to piping for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. Meets ASTM D3034.
Brass Craft CSSTNN-34N Gas Appliance Connectors BrassCraftCSSLNN-10NGasApplianceConnectors Brass Craft CSSL54-12 Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSD54-12 Gas Appliance Connectors Brass Craft CSSLNN-16N Gas Appliance Connector BrassCraftCSSCNN-22NGasApplianceConnectors
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
BrassCraftCSSLNN-22NGasApplianceConnectors BrassCraftCSSLNN-28NGasApplianceConnectors Brass Craft CSSLNN-34N Gas Appliance Connector
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
B and K Industries G014SS101118RP Gas Connectors Simmons 8842 Hydrant Plunger Brass Craft CSSTNN-46N Gas Appliance Connectors
CSA certified up to .05 PSIG, -40 to 150 degrees operating temperature. Replacement plunger for Simmons 800 series lead free, deluxe frost-proof yard hydrants. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Genova 41860 Pipe Plug Brass Craft CSSL54-18 Gas Appliance Connectors Brass Craft CSSNN-28N Gas Appliance Connector
Used to form a removable closure. Teflon thread tape is recommended for threaded joints.  4" and 6" meet ASTM D3034. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Brass Craft CSSC21-24 Gas Appliance Connectors Brass Craft CSSL54-36 Gas Appliance Connectors Brass Craft CSSL54-24 Gas Appliance Connectors
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSCNN-16N Gas Appliance Connector BrassCraftCSSCNN-34NGasApplianceConnectors Brass Craft CSSD54-18 Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSD54-24 Gas Appliance Connectors Brass Craft CSSC21-18 Gas Appliance Connectors Brass Craft CSSD54-30 Gas Appliance Connectors
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSL54-30 Gas Appliance Connectors Brass Craft CSSTNN-58N Gas Appliance Connectors Brass Craft CSSC21-30 Gas Appliance Connector
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas appliance connector without fittings. Use with adaptors and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSC21-36 Gas Appliance Connectors Brass Craft CSSD54-36 Gas Appliance Connectors Brass Craft CSSLNN-46N Gas Appliance Connector
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested.
Brass Craft CSSCNN-46N Gas Appliance Connectors Brass Craft CSSL54-48 Gas Appliance Connector Brass Craft CSSD54-48 Gas Appliance Connectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSC21-48 Gas Appliance Connectors Simmons 872 Hydrant Elbow Genova Products 41644 PVC Sewer and Drain Cleanout
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. 3/4" MPT x 3/4" Insert. Used with a vertical pipe stack to provide for above ground level access to piping for sewer lines, septic tank and seepage systems.
Brass Craft CSSLNN-58N Gas Appliance Connectors Brass Craft CSSD54-60 Gas Appliance Connectors Genova 41659 PVC Sewer-Drain Fitting
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Solvent welds into fitting hub and adapts to male threaded plug for sewer lines, septic tank and seepage systems. Teflon thread tape is recommended for threaded joints. 3" meets ASTM D2949 or exceeds ASTM D2729; 4" and 6" meet ASTM D3034.
BrassCraftCSSCNN-58NGasApplianceConnectors Brass Craft CSSL54-60 Gas Appliance Connectors BrassCraftCSSL44E-24PGasApplianceConnectors
Coated stainless steel gas appliance connector without fittings. Use with adapters and valves only. Connectors without fittings are not CSA designed-certified. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSC21-60 Gas Appliance Connectors BrassCraftCSSL44E-36PGasApplianceConnectors BrassCraftCSSD44E-18PGasApplianceConnectors
ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Eagle Mountain RK-Y34 Yard Hydrant Repair Kit BrassCraftCSSD44E-24PGasApplianceConnectors BrassCraftCSSC44E-24PGasApplianceConnectors
Contains: rod stem, packing nut, packing, support washer, plunger. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
Brass Craft CSSC12E-36 P Gas Appliance Connectors BrassCraftCSSC44E-36PGasApplianceConnectors Simmons 850 SB Yard Hydrant Repair Kit
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Kit contains No.8825 brass connector, No.8826 brass links (Pair), No.8847 brass packing nut, No.8839 buna-N "O" rings (Pair), No.8842 plunger (one piece), No.8301 stainless steel lock nut, No.8836 fulcrum bolt, and No.8837 square head set screw.
BrassCraftCSSL47E-24PGasApplianceConnectors Brass Craft CSSD44E-36P Gas Appliance Connectors BrassCraftCSSC12E-48PGasApplianceConnectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
BrassCraftCSSL44E-48PGasApplianceConnectors BrassCraftCSSL47E-36PGasApplianceConnectors Brass Craft CSSC21-72 Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration.
Brass Craft CSSD44E-48 P Gas Appliance Connectors Brass Craft CSSB22-36 Gas Appliance Connectors Brass Craft CSSD44E-60P Gas Appliance Connectors
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested.
BrassCraftCSSC44E-48PGasApplianceConnectors Brass Craft CSSB22-60 Gas Appliance Connectors Pro-Flex PFCT-1225 Pro-Flex
Coated stainless steel gas connector with excess flow valve. The Safety+Plus flow valve is an automatic safety valve for gas designed to help prevent fires and explosions due to gas line ruptures or disconnects at the appliance. It is equipped with automatic reset and automatic valve activation. The ProCoat polymer-based coating resists corrosion from harsh chemicals found in common household cleaning, plumbing repair, and masonry products. Approved for indoor and outdoor use, the ProCoat coating resists the harsh effects of the UV rays and salt. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced air heating units, and rooftop HVAC units. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Leak tested. ProCoat coated stainless steel gas connector with fittings. For use with residential and commercial gas appliances not subject to frequent movement that utilize natural, manufactured, mixed, liquefied-petroleum gases and LP gas-air mixtures: residential kitchen appliances, infrared or blue-flame "hearth-style" heating units, decorative gas log appliances, pulse combustion furnaces, manufactured housing (permanent residence mobile homes), laundry/utility appliances, forced ait heating units, and rooftop HVAC units. Superior corrosion resistance. Greater strength and flexibility. Easy to install. CSA certified for indoor and outdoor use. 100% leak tested. Design-certified (assembled connector) and manufactured in accordance with ANSI Z21.24, ANSI Z21.75, AGAL Contract No. 8204, listed by the New York City Board of Standards and Appeals and by the Commonwealth of Massachusetts Division of Registration. Flexible 304 stainless steel with yellow polyethylene jacketing. All tubing clearly marked with gas pressure rating, EHD (Equivalent Hydraulic Diameter). Tested to the ANSI Standards for Fuel Gas Piping System using Corrugated Stainless Steel Tubing(CSST), ANSI LC-1a-2009, CSA 6.26a-2009, ANSI LC-1-2005 and CSA 6.26-2005.
Simmons 800LF Yard Hydrants Simmons 802LF Yard Hydrants Simmons 803LF Yard Hydrants
Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant. Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant. Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant.
Simmons 804LF Yard Hydrants Simmons 805LF Yard Hydrants Pro-Flex PFCT-3425 Pro-Flex
Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant. Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant. Flexible 304 stainless steel with yellow polyethylene jacketing. All tubing clearly marked with gas pressure rating, EHD (Equivalent Hydraulic Diameter). Tested to the ANSI Standards for Fuel Gas Piping System using Corrugated Stainless Steel Tubing(CSST), ANSI LC-1a-2009, CSA 6.26a-2009, ANSI LC-1-2005 and CSA 6.26-2005.
Simmons 806LF Yard Hydrants Simmons 808LF Yard Hydrant Eagle Mountain Y34-2 Yard Hydrant
Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant. Shut-off valve operates below the frost line. Hydrant cannot freeze because when it is closed, all water in the stand pipe drains out of a hole in the valve which is set in the ground below the frost line. Pistol type handle. Hand wheel designed to lock the flow of water at rate desired. Solid brass rod through brass packing nut will not rust and cut into rubber O-rings. Solid brass links and connector. 1 piece molded Buna 'N plunger can be easily adjusted or replaced without removing hydrant. Immediate-flow, even in sub-zero temperatures, all repairs can be made from the head of the unit, adjustable link provides an easy adjustment for positive shut-off, rod guide reduces wear on packing, packing nut and brass stem. Flow finder and lock automatically sets the same flow each time or can be locked against accidental opening. One-piece variable-flow plunger and the large cushion type seal for long life, assuring shut-off, even when foreign particles are present in the water line. Graphite packing for lubricity and long-life. Hot-dipped galvanized pipe casing and operating pipe stem. Automatic draining when hydrant is shut off.
Eagle Mountain Y34-4 Yard Hydrant Eagle Mountain Y34-5 Yard Hydrant Eagle Mountain Y34-3 Yard Hydrant
Immediate-flow, even in sub-zero temperatures, all repairs can be made from the head of the unit, adjustable link provides an easy adjustment for positive shut-off, rod guide reduces wear on packing, packing nut and brass stem. Flow finder and lock automatically sets the same flow each time or can be locked against accidental opening. One-piece variable-flow plunger and the large cushion type seal for long life, assuring shut-off, even when foreign particles are present in the water line. Graphite packing for lubricity and long-life. Hot-dipped galvanized pipe casing and operating pipe stem. Automatic draining when hydrant is shut off. Immediate-flow, even in sub-zero temperatures, all repairs can be made from the head of the unit, adjustable link provides an easy adjustment for positive shut-off, rod guide reduces wear on packing, packing nut and brass stem. Flow finder and lock automatically sets the same flow each time or can be locked against accidental opening. One-piece variable-flow plunger and the large cushion type seal for long life, assuring shut-off, even when foreign particles are present in the water line. Graphite packing for lubricity and long-life. Hot-dipped galvanized pipe casing and operating pipe stem. Automatic draining when hydrant is shut off. Immediate-flow, even in sub-zero temperatures, all repairs can be made from the head of the unit, adjustable link provides an easy adjustment for positive shut-off, rod guide reduces wear on packing, packing nut and brass stem. Flow finder and lock automatically sets the same flow each time or can be locked against accidental opening. One-piece variable-flow plunger and the large cushion type seal for long life, assuring shut-off, even when foreign particles are present in the water line. Graphite packing for lubricity and long-life. Hot-dipped galvanized pipe casing and operating pipe stem. Automatic draining when hydrant is shut off.
Eagle Mountain Y34-6 Yard Hydrant Pro-Flex PFCT-1275 Pro-Flex Pro-Flex PFCT-3475 Pro-Flex
Immediate-flow, even in sub-zero temperatures, all repairs can be made from the head of the unit, adjustable link provides an easy adjustment for positive shut-off, rod guide reduces wear on packing, packing nut and brass stem. Flow finder and lock automatically sets the same flow each time or can be locked against accidental opening. One-piece variable-flow plunger and the large cushion type seal for long life, assuring shut-off, even when foreign particles are present in the water line. Graphite packing for lubricity and long-life. Hot-dipped galvanized pipe casing and operating pipe stem. Automatic draining when hydrant is shut off. Flexible 304 stainless steel with yellow polyethylene jacketing. All tubing clearly marked with gas pressure rating, EHD (Equivalent Hydraulic Diameter). Tested to the ANSI Standards for Fuel Gas Piping System using Corrugated Stainless Steel Tubing(CSST), ANSI LC-1a-2009, CSA 6.26a-2009, ANSI LC-1-2005 and CSA 6.26-2005. Flexible 304 stainless steel with yellow polyethylene jacketing. All tubing clearly marked with gas pressure rating, EHD (Equivalent Hydraulic Diameter). Tested to the ANSI Standards for Fuel Gas Piping System using Corrugated Stainless Steel Tubing(CSST), ANSI LC-1a-2009, CSA 6.26a-2009, ANSI LC-1-2005 and CSA 6.26-2005.
Pro-Flex PFCT-12225 Pro-Flex Pro-Flex PFCT-34225 Pro-Flex
Flexible 304 stainless steel with yellow polyethylene jacketing. All tubing clearly marked with gas pressure rating, EHD (Equivalent Hydraulic Diameter). Tested to the ANSI Standards for Fuel Gas Piping System using Corrugated Stainless Steel Tubing(CSST), ANSI LC-1a-2009, CSA 6.26a-2009, ANSI LC-1-2005 and CSA 6.26-2005. Flexible 304 stainless steel with yellow polyethylene jacketing. All tubing clearly marked with gas pressure rating, EHD (Equivalent Hydraulic Diameter). Tested to the ANSI Standards for Fuel Gas Piping System using Corrugated Stainless Steel Tubing(CSST), ANSI LC-1a-2009, CSA 6.26a-2009, ANSI LC-1-2005 and CSA 6.26-2005.
   
 
1