Home > PLUMBING > KITCHEN & BATH > FAUCET / SINK REPAIR > SLIP JOINT WASHERS / NUTS
Sort By:
1
SLIP JOINT WASHER 1-1/2 NO2B  Plumb Pak PP25519 Tailpiece Washers Plumb Pak PP20956 Slip Joint Nut
1-1/2". O.D. X 1-1/4". I.D. X 3/16 H. Fits tube size 1-1/4 in. Use Ring #2. Forms a seal which helps prevent leaks. Easy to install. Includes 1 washer. Plumb Pak Tailpiece Washer, Beveled, 1-1/2 in, Polyethylene, For Plastic Drainage Systems Plumb Pak Slip Joint Nut, 1-1/4 in, Plastic, White, For Plastic Drainage Systems
World Wide Sourcing 24306 Faucet Coupling Nut TAPE ELECT VNYL BLK 3/4INX60FT Plumb Pak PP25535 Tailpiece Washer
Fits 1/2'' iron pipe faucet shanks. 2 per bag. Black vinyl electrical tape for common electrical uses. 7 mil., UL Approved. Plumb Pak Poly Washer, Beveled, 1-1/4 in, Polyethylene, For Plastic Drainage Systems
Plumb Pak PP20955 Slip Joint Nut Intertape 602 Electrical Tape World Wide Sourcing PMB-086 Drain Tailpiece Washers
Plumb Pak Slip Joint Nut, 1-1/2 in Size, PVC, White General purpose electrical insulating tape, good dielectric strength. 7 mils thick. UL Listed and CSA Certified. WORLDWIDE SOURCING Drain Tailpiece Washer, Polyethylene, 1-1/2 in ID
World Wide Sourcing 24467 Faucet Hole Cover Plumb Pak PP25515 Drain Tailpiece Washers Calterm 49305 Electrical Tape 30 ft L x 7.5 mil T
Covers unused spray or faucet hole. Plumb Pak Drain Tailpiece Washer, 1-1/2 in, Polyethylene, For Plastic Drainage Systems Black PVC electrical tape is UL Listed to 600 volt. 7.5 mil. thickness and a temperature rating up to 80 degrees Celsius/176 degrees Fahrenheit. Elongation of 200 percent allows tight wrapping and sealing.
WireGard 19-AWC Assortment Wire Connector Kit WireGard 19-001 Twist-On Wire Connector WireGard 19-002 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WireGard 19-003 Twist-On Wire Connector WireGard 19-004 Twist-On Wire Connector WireGard 19-006 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WingGard 19-084 Twist-On Wire Connector WingGard 19-086 Twist-On Wire Connector Hex-Lok 19-2H2 Hex Lock Wire Connector
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
WingGard 19-089 Twist-On Wire Connector GreenGard 19-095 Grounding Wire Connector World Wide Sourcing PMB-089 Slip Joint Washer
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections. Worldwide Sourcing Slip Joint Washer, 1-1/2 in Nominal, Rubber
LOCKNUT SHANK IPS FAUCET 1/2IN WASHER POLY SLIP 1-1/2IN O.D. World Wide Sourcing 24466 Faucet Hole Cover
Plastic construction, universal design fits standard 1/2? IPS faucet shanks. Attaches to the faucet shanks from underneath the counter. Plastic. No brass friction ring needed. Covers unused spray or faucet hole.
Plumb Pak PP25516 Slip Joint Washer STRAINER SINK WASHER ASSORT   WASHER POLY SLIP 1-1/4IN O.D.
Plumb Pak Slip Joint Washer, 1-1/4 in, Rubber, For Water Supplies Includes one rubber washer and one poly washer. 1-3/4" OD x 1-3/8" ID x 1/8 in thick. Universal design. Plastic. No brass friction ring needed.
Intertape 85828 Electrical Tape Intertape 85827 Electrical Tape Intertape 85835 Electrical Tape
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85830 Electrical Tape Intertape 85832 Electrical Tape Intertape 85831 Electrical Tape
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
NUT/WASHER SLIPJOINT 1-1/2 WHT TAILPIECE NUT 1/2IN IPS FAUCET World Wide Sourcing PMB-095 Faucet Coupling Nuts
Plastic. Includes washer and nut. No brass friction rings needed. Metal construction, 1/2" IPS thread on nut. Universal design fits most faucets. Chrome plated. 1/2" iron pipe size.
Erico ESB8 Split Bolt Connector NUT/WASHER SLIPJOINT 1-1/4 WHT Erico ESB6 Blackburn Split Bolt Connectors
Silicon bronze for copper to copper. UL Listed. Plastic. Includes washer and nut. No brass friction rings needed. Silicon bronze for copper to copper. UL Listed.
Plumb Pak PP25509 Slip Nut & Washer WASHER/NUT ROSETTE 1/2IN IPS  NUT/WASHER SLIPJOINT 1-1/2 WHT
Plumb Pak Slip Nut, 1-1/4 in, Die Cast, For Brass Drainage Systems Plastic nut, 1/2" IPS thread on nut, metal rosette washer. Universal design. Plastic. Includes washer and nut. No brass friction rings needed.
Plumb Pak PP25517 Slip Joint Washers Scotch 4218-BA-40 Electrical Tape Plumb Pak PP25511 Slip Nuts and Washers
Plumb Pak Slip Joint Washer, 1-1/2 in, Rubber, For Water Supplies Commercial grade 7-mil polyvinyl chloride insulating tape, flame retardant and provides mechanical protection with minimum bulk. Excellent resistance to abrasion, moisture, acids, copper corrosion and varying weather conditions. UL Listed and CSA Certified. Plumb Pak Slip Nut, 1-1/2 in, Die Cast, For Water Supplies
Erico ESBP8 Split Bolt Connector Spacer SINK HOLE COVER 1-1/2 CHROME  Jandorf 60935 Closed End Connector 22 - 18 AWG
With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper. Jandorf Closed End Connector Series: 60935, 22 - 18 AWG Conductor, Fully Insulated Insulation, Vinyl Insulation, Clear, Tin Plated Copper, UL Listed
Gardner Bender 20-410 Crimp Sleeve Connector Calterm 61470 Assortment Wire Cap Set Plumb Pak PP25535-20 Slip Joint Washer
Zinc plated steel. Suitable for solid or stranded copper wire. Plumb Pak Slip Joint Washer, Beveled, 1-1/4 in, Polyethylene
WireGard 25-002 Twist-On Wire Connector Gardner Bender GTF-300 Friction Tape WireGard 25-001 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. For use over electrical tape splices. Matted finish provides the best gripping surface available. Use to wrap grips on hand tools. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
GB-Gardner Bender GTB-667P Electrical Tape GB-Gardner Bender GTW-667P Electrical Tape SLIP JOINT WASHER ASSORTMENT
Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Plastic. No brass friction ring needed.
NUT TAILPIECE 1/2IN IPS FAUCET Erico ESBP6 Split Bolt Connectors Hex-Lok 19-1H1 Hex Lock Wire Connector
For use with hot or cold water. Connects water supply line to faucet. 1/2" IPS. 2 per card. With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper. Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs.
GB-Gardner Bender GTO-667P Electrical Tape Plumb Pak PP20965 Slip Joint Washer Gardner Bender 20-411 Crimp Sleeve Connector
Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Contains 1 each 1-1/2" x 1-1/2" and 1-1/2" x 1-1/4". Bagged. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed.
Plumb Pak PP25519-20 Slip Joint Washer WireGard 25-003 Twist-On Wire Connector Gardner Bender 20-089 Closed End Crimp Pigtail Connector
Plumb Pak Slip Joint Washer, Beveled, 1-1/2 in, Polyethylene Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed.
Gardner Bender 20-090 Closed End Crimp Pigtail Connector SINK HOLE COVER 1-1/4 CHROME  Jandorf 60820 Closed End Connector 12 - 10 AWG
Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed. Jandorf Closed End Connector Series: 60820, 12 - 10 AWG Conductor, Insulated Insulation, Nylon Insulation, Clear, Tin Plated Copper, UL Listed
PushGard 19-PC2 2-Port Push-In Connector Plumb Pak PP20965-20 Slip Joint Washer Super 33+ 195NA Electrical Tape
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Plumb Pak Slip Joint Washer, Beveled, 1-1/2 x 1-1/4 in, Polyethylene For insulating, repairing and protecting electrical wire. UL Listed.
PushGard 19-PC3 3-Port Push-In Connector WingGard 25-084 Twist-On Wire Connector Plumb Pak PP21511 Faucet Hole Covers
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. 1-1/2 diameter.
Danco 80360 Waterproof Faucet Grease PushGard 19-PC4 4-Port Push-In Connector WireGard 25-004 Twist-On Wire Connector
Use as a lubricant on faucet and stems. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Danco 88693 Silicone Faucet Grease Gardner Bender DS-110N Duct Seal Insulator Gardner Bender TK-32 Assortment Wire Connector Kit
Used as a lubricant on faucets and stems. Malleable non-conductive compound for sealing of electrical raceway connections from air, noise and moisture. Slide card kit with 32 assorted wire connectors: 10 GB #1 - minimum 3 #22 maximum 2 #16, 8 GB #2 - minimum 3 #22 maximum 3 #18 w/2 #20 6 GB #3 - minimum 3 #20 maximum 2 #14, 2 GB #4 - minimum 1 #14 maximum 4 #12, 4 crimp connector #1035 - 1 #20 w/1 #12 - 2 #14, 2 crimp connector #1034 - 4 #22 - 2 #16.
GASKET TAILPIECE WASTE BEND   Erico ESB4 Blackburn Split Bolt Connectors Harvey 050090 Silicone Grease
Compatible with InSinkEerator models 333,17 & 17. Designed for use with tailpiece elbow. Silicon bronze for copper to copper. UL Listed. Apply to rubber and synthetic ``O" rings. 90% pure silicone, contains no petroleum additives. Offers greater heat resistance, up to 450 degrees Fahrenheit. Non-staining.
Plumb Pak PP800-80 Basin Coupling Nut Danco 36644B Slip Joint Washer Danco 36649B Slip Joint Washer
Chrome plated. 1/2'' iron pipe size. Danco Slip Joint Washer, Medium Wall, 1-1/4 in ID x 1-7/16 in OD x 3/16 in Thick, 1-1/4 in Nut, 1-1/4 in Tube, Rubber, Orange Danco Slip Joint Washer, 1-1/2 in ID x 1-11/16 in OD x 3/16 in Thick, 1-1/2 in Nut, 1-1/2 in Tube, Rubber, Orange
Gardner Bender GTF-600 Friction Tape 3M 10414 Electrical Tape WingGard 25-086 Twist-On Wire Connector
For use over electrical tape splices. Matted finish provides the best gripping surface available. Use to wrap grips on hand tools. Resists water, oils, alkalies, acids, weather, ultraviolet rays, abrasion, corrosion and moisture. Use as a primary insulation for wide cable splices up to 600 volt, for fixture and wire splices up to 1000 volt and to maintain electrical and high temperature integrity of electrical systems. 7 mil, UL Approved and CSA Certified. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Gardner Bender GTP-307WD All Weather Electrical Tape Plumb Pak PP21501 Faucet Hole Cover Plumb Pak PP815-1 Faucet Hole Cover
General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. 1-3/4" diameter. 1-3/4" diameter.
Plumb Pak PP815-11 Faucet Hole Covers Gardner Bender RTP-3422 Self-Sealing Electrical Tape Danco 38808B Cone Washer
1-1/2 diameter. Insulates and seals surfaces. Fuses to itself during application to stay watertight. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. 3/8"H for applications including 3/8"OD tubing into lavatory/sink fixtures. Use with 45/64"OD x 25/64"ID x 3/64" thick No.36617 friction ring. Bagged.
Danco 36651B Slip Joint Washer Danco 36642B Slip Joint Washer Danco 36643B Slip Joint Washer
Danco Slip Joint Washer, 1-1/2 in Nut, 1-1/2 in Tube, 3/16 in Thick, Rubber Danco Slip Joint Washer, 1-11/16 in ID x 1-7/16 in OD, 1-1/4 in Nut, 1-1/4 in Tube, Rubber, Orange Danco Slip Joint Washer, 1-11/16 in ID x 1-7/16 in OD, 1-1/2 in Nut, 1-1/2 in Tube, Rubber, Orange
Danco 36661B Slip Joint Washer Danco 36647B Slip Joint Washer Scotch 35 Color Coding Electrical Tape
Molded in one piece from first-grade polyethylene and beveled for a sure grip and positive fit. Impervious to all acids, detergents, minerals and pipe cleaning chemicals. No brass friction rings needed. Danco Slip Joint Washer, 1-7/32 in ID x 1-23/32 in OD x 3/16 in Thick, 1-1/2 in Nut, 1-1/4 in Tube, Rubber, Orange Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified.
Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape
Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified.
Worldwide Sourcing TW0915 Po Plug Drains DryConn 20101 Low Voltage Wire Connector DryConn 62210 Safety Sealed Waterproof Wire Connector
One piece ABS plastic construction. With chain and stopper. Suitable for all low voltage applications. For use in lighting, irrigation, and underground wiring. No junction box required. Filled with petroleum based sealant. 30 volt/10 amps maximum. 13/16" x 19/16". Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL 486D Listed.
DryConn 62110 Safety Sealed Waterproof Wire Connector DryConn 62310 Safety Sealed Waterproof Wire Connector Scotch Super 33+ 6132 Electrical Tape
Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL 486D Listed. Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL 486D Listed. Resists water, oils, alkalies, acids, weather, ultraviolet rays, abrasion, corrosion and moisture. Use as a primary insulation for wide cable splices up to 600 volt, for fixture and wire splices up to 1000 volt and to maintain electrical and high temperature integrity of electrical systems. 7 mil, UL Approved and CSA Certified.
Mintcraft CP-323L Wire Cap Set Plumb Pak PP800-81 Coupling Nut Super 33+ 200 Electrical Tape
Thirty two piece, for AWG #24 to AWG #10 solid or standard copper wire. Contains: 10 pc wire joint 22-16  300 volt, 2/#22 - 2/#16. 8 piece wire joint 22-14 300 volt 3/#22 - 3/#16. 6 pc wire joint 22-14 600 volt 2/#18 - 4/#16. 2 piece wire joint 18-12 600 volt 1/#18 + #14 - 1 and 2/#14 + 3/#16. 4 piece closed end pigtail 16-14 2/#22 - 2/#14. 2 piece closed end pigtail 12-10 2/#18 - 2/#10. 2 per card. Vinyl electrical tape, black, 7 mil thick with PVC backing, provides protective jacketing for high-voltage cables and wire harnesses, and primary electrical insulation for splices up to 600 volt. Abrasion, corrosion, and UV resistant, resists alkalis and acids, and is flame-retardant. All-weather performance in cold to 0 degrees F or heat to 220 degrees F. UL Listed and CSA Certified.
Danco 36622B Sink Strainer Coupling Nut Washer Danco 36669B Cone Washer Plumb Pak PP800-88 Fit Faucet Locknut and Rosette
Used between the shank of the sink strainer and the lip of the tailpiece with the 1-1/2" coupling nut making the connection. 1/8" lip - 9/32" thick. Bagged. 1-piece, 13/32"H for applications including 1/2" IPS for threaded ballcock supply. Used with stops having corrugated supplies. Bagged. Plumb Pak Faucet Locknut and Rosette, Universal Fit
DryConn 10600 Twist-On Underground Wire Connector WireGard 25-AWC Assortment Wire Connector Kit WireGard 25-006 Twist-On Wire Connector
Rated for all underground direct bury applications. Use on all lighting, irrigation, and underground wiring. Additional sealant for long term service. No junction box needed. 600 volt maximum with building wire, 1000 volt in fixtures and signs. #8 to #22 wire range. UL 486D Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Scotch 03407 Friction Tape Erico ESBP2 Split Bolt Connectors Danco 38803B Cone Washer
Good abrasion resistance, used for protection for electrical tape splices and connectors. Made in the USA. UL Approved. With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper. 1/4"H. Application: 3/8" IPS ballcock supply and laundry trays.
Danco 52513B Sink Clips Danco 36668B Cone Washer Danco 38805B Cone Washer
Bagged. 1-piece, 13/32"H for applications including 1/2" IPS for threaded basin supply. Used with stops having corrugated supplies. Bagged. 3/8"H for applications including 3/8"OD tubing into lavatory or sink fixtures. Use with 45/64"OD x 25/64"ID x 3/64" thick No.36617 friction ring. Bagged.
Danco 38809B Cone Washer PushGard 19-PC8 8-Port Push-In Connector Erico ESB2 Blackburn Split Bolt Connectors
3/8"H for applications including 3/8"OD tubing into ballcock. Use with 13/16"OD x 13/32"ID x 3/64" thick No.36618 friction ring. Bagged. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Silicon bronze for copper to copper. UL Listed.
Erico ESBP1/0 Split Bolt Connectors Scotch 88 Cold Weather Electrical Tape Plumb Pak PP855-10 Slip Nut & Washer
With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper. Thick 8.5 mil. Recommended for low temperature applications because of its superior cold weather handling features. Flexible for use on small wires. Inside or outside. Resists cold, ultraviolet rays, moisture, alkalies, acids and corrosion. Die cast with washers.
Danco 52512B Sink Clips Danco 36660B Slip Joint Washer COVER SINK HOLE 1-3/4IN SS
Bagged. Molded in one piece from first-grade polyethylene and beveled for a sure grip and positive fit. Impervious to all acids, detergents, minerals and pipe cleaning chemicals. No brass friction rings needed.
WireGard 10-001 Twist-On Wire Connector Danco 38806B Cone Washer Danco 38807B Cone Washer
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. 5/16"H for applications including 3/8"OD tubing into ballcocks. Use with 13/16"OD x 13/32"ID x 3/64" thick No.36618 friction ring. Bagged. 3/8"H for applications including 1/2"OD tubing into ballcocks. Use with 13/16"OD x 17/32"ID x 3/64" thick No.36618 friction ring. Bagged.
Plumb Pak PP826-81 Sink/Basin Hangers CONNECTOR WIRE ASSORTMNT 158PC Erico ESB2/0 Blackburn Split Bolt Connectors
3.75"h x 2.625"w Cone shaped springs pull wire into the connectors for a firm & secure grip. Pretwisting wires is not required. Maximum rated voltage: Grey, blue, & orange: 300 Volts; Yellow & red: 600 Volts. Neatly organized PVC storage case. Silicon bronze for copper to copper. UL Listed.
GreenGard 25-095 Grounding Wire Connector Danco 52509B Sink Clip Screws Danco 38802B Cone Washer
Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections. Bagged. 1/2"H. For applications including 1/2" nut, 7/16" or 3/8"OD tube for basin Speedy connector. Use with 45/64"OD x 25/64"ID x 3/64" thick No.36617 friction ring. Bagged.
Danco 38804B Cone Washer Scotch 35 Color Coding Electrical Tape WireGard 10-002 Twist-On Wire Connector
1/4"H for applications including 1/2" IPS shallow nuts, 7/16" or 3/8"OD tubing. Use with 23/32"OD x 9/16"ID x 1/32" thick No.36614 friction ring. Bagged. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Hex-Lok 25-2H2 Hex Lock Wire Connector Hex-Lok 25-1H1 Hex Lock Wire Connector Intertape 5517 Electrical Tape
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs. Semi-cured rubber for low voltage electrical insulation, 30 mil. Self-vulcanizing and water resistant.
Danco 73113B Faucet Shank Locknut Danco 36662B Slip Joint Washer Erico ESB1/0 Split Bolt Connector
White plastic. Bagged. Molded in one piece from first-grade polyethylene and beveled for a sure grip and positive fit. Impervious to all acids, detergents, minerals and pipe cleaning chemicals. No brass friction rings needed. Silicon bronze for copper to copper. UL Listed.
Danco 36598B Cone Washer Danco 36590B Cone Washer WING NUT SJ 1 1/2 X1 1/2 SPLIT
5/16'h. Application: 7/16" O.D. tube into 1/2 IPS nuts. 5/16H. Application: basin and 1/2" ballcock supply. White polypropylene slip joint split nut and washer.
WING NUT SJ 1 1/4 X1 1/4 SPLIT 3M 10457 Assortment Colored Electrical Tape Kit 3M DBO/B-6 Underground Splice Kit
White polypropylene slip joint split nut and washer. Insulates and protects against abrasion, weather, water, solvent splashes and chemicals. Stretchy, vinyl plastic. Applications include home, marine, auto, trailers and tools. Flame retardant. Pack of 5 colors. Designed to connect and moisture seal electrical connection for direct bury applications, 18-10 AWG, rated up to 600 volts. Combines the quick, reliable connection of a spring connector O/B with the moisture resistance of a high-impact, UV-resistant tube prefilled with moisture-resistant grease. For use with irrigation systems on golf courses, around business and for outdoor lighting systems. Application temperature range 32 - 120 degrees Fahrenheit. EU RoHS Compliant. Flame retardant. UL listed for direct bury.
Sterling 1150001 Sink Clip WingGard 25-089 Twist-On Wire Connector Gardner Bender HTP-1010 Self-Sealing Tape
Used to install rolled rim stainless sinks. For use on model No.114014NA, 114024NA, 147074NA, 147084NA,114044NA, and 114054NA. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Self-sealing silicone repair tape. Stretch, wrap, and protect or repair everything from leaky hoses, pipe insulation, electrical connections, tool handles, air ducts and cord/rope ends. Non-adhesive formula leaves no sticky residue. Waterproof and insulate with no extra equipment or heat required. Stretches up to 300 percent of its original length with 60 ppi tear strength. Begins to bond immediately on contact with itself. Repositioning is not recommended after 2 minutes of contact, and the bond is permanent within 24 hours. Operates and remains flexible from -60 degreesF (-51 degreesC) to 500 degreesF (260 degreesC).
Danco 52511B Sink Clip Screws WingGard 17-084 Twist-On Wire Connector Erico ESB4/0 Blackburn Split Bolt Connectors
Bagged. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Silicon bronze for copper to copper. UL Listed.
WireGard 10-003 Twist-On Wire Connector Danco 36593B Cone Washer Danco 52517B Sink Clips
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. 3/8" H. Application: rubber-nose closet supplies, upper bath, ballcock supply, 7/16" tubing. Bagged.
Danco 73106B Faucet Locknut CONNECTOR ELEC ASSORTMNT 308PC Shurtech 442055 Electrical Tape
Danco Faucet Locknut, 1/2 in IPS, Metal Tin plated copper constructed terminals & connectors provide a secure connection between two wires without soldering. Nylon cable clamps can be used for securing & organizing cables, wires, tubings, & rods. UL Listed 100% polyolefin constructed heat-shrink tubings provide an insulated and flame retardant covering for wrapping wire harnesses. Self-fusing 20 mil tape, watertight seal for plumbing, auto, marine and general purpose applications.
WingGard 17-086 Twist-On Wire Connector GB-Gardner Bender GSBC-8 Split Bolt Connectors Danco 73114B Faucet Tailpiece Nut
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. For use with copper to copper conductors only. 600 volt copper only. Bagged.
Erico ESBP2/0 Split Bolt Connectors WireGard 16-003 Twist-On Wire Connector Gardner Bender LTR-400 Electrical Tape
With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Liquid coating used to insulate and protect electrical splices and connections. Waterproof, will not unravel or deteriorate like traditional tape. Indoor/outdoor, for home, auto/marine and electrical applications. Brush-on applicator included. 4 oz. can, carded.
Gardner Bender LTB-400 Electrical Tape Danco 88532 Ball Rod Assembly TAPE LIQUID 4OZ BOTTLE WHITE
Liquid coating used to insulate and protect electrical splices and connections. Waterproof, will not unravel or deteriorate like traditional tape. Indoor/outdoor, for home, auto/marine and electrical applications. Brush-on applicator included. 4 oz. can, carded. 6" brass rod replaces most existing lavatory ball rod assemblies. Includes 1 rod, 3 various-sized balls, and 2 cone washers. Carded. Liquid coating used to insulate and protect electrical splices and connections. Waterproof, will not unravel or deteriorate like traditional tape. Indoor/outdoor, for home, auto/marine and electrical applications. Brush-on applicator included. 4 oz. can, carded.
Scotch 2242 Linerless Electrical Tape WingGard 10-084 Twist-On Wire Connector WireGard 10-004 Twist-On Wire Connector
Economical, general purpose, rubber, highly conformable, linerless Ethylene Propylene based electrical insulating tape. Weather Resistant. Uniform tape unwind, small roll size (OD). Five year shelf life. Stable over wide application and temperature range, temperature rating of 194 degrees F continuous, 266 degrees F short-term. Designed for all-voltage splicing, jacketing, and general insulating use in splicing and terminating wires and cables. Flame retardant, physical and electrical properties unaffected by degree of stretch. Provides immediate moisture seals and void free buildup. 30 mils thick, 250 psi tensile strength, 1000 percent ultimate elongation. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
SINK CLIP TILE COUNTER ADJUST Gardner Bender GTP-307 Electrical Tape Worldwide Sourcing TW0911-3L Po Plug Drains
Metal construction. Includes four adjustable sink clips. General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. One piece solid brass construction. Chrome finish with chain and stopper.
Plumb Pak PP815-1BN Faucet Hole Cover GB-Gardner Bender GSBC-6 Split Bolt Connectors World Wide Sourcing TW0914 Po Plug Drain
1-3/4" diameter. For use with copper to copper conductors only. 600 volt copper only. One piece solid brass construction. Chrome finish with chain and stopper.
Gardner Bender 10-411 Crimp Sleeve Connector WireGard 16-002 Twist-On Wire Connector Plastidip LET14Z03 Electrical Tape
Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. A rubber insulation coating that exhibits excellent acid, alkaline, abrasion protection and seals out moisture and salt permanently. Liquid Tape has the strongest dielectric protection; 1,400 v\mil, 5-7 mils per coat. Will not harden, unravel or become brittle in extreme weather. Use to insulate cables, electronics, outdoor lighting, underground wiring, alarms, security systems, utility trailers, takes the place of electrical tape.
GB-Gardner Bender GAK-2 Split Bolt Connectors Plumb Pak PP9256W Slip Joint Nut WingGard 16-084 Twist-On Wire Connector
Constructed of high-strength aluminum with oxide-displacing jaws to prevent galvanic corrosion. UL Listed. Plumb Pak Slip Joint Nut, 1-1/4 in, PVC, White Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Gardner Bender GTP-607 All Weather Electrical Tape Gardner Bender 10-410 Crimp Sleeve Connector Gardner Bender 10-410C Crimp Sleeve Connector
General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed.
Hex-Lok 10-2H2 Hex Lock Wire Connector WireGard 10-006 Twist-On Wire Connector Plumb Pak PP20551
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Stainless steel rim. Lift 'n Lok top. 1-1/4" x 5" size.
Plumb Pak PP20219 Po Plug Drains PushGard 10-PC3 3-Port Push-In Connector WingGard 10-086 Twist-On Wire Connector
Complete assembly with stopper and chain. 1-1/4" x 5". Chrome plated. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
GB-Gardner Bender GSBC-1/0 Split Bolt Connectors Plumb Pak PP55-1 Po Plug Drain PushGard 10-PC4 4-Port Push-In Connector
For use with copper to copper conductors only. 600 volt copper only. 1-1/4" x 5". Stainless steel rim. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only.
Hex-Lok 10-1H1 Hex Lock Wire Connector