Home > PLUMBING > KITCHEN & BATH > FAUCET / SINK REPAIR > FAUCET HANDLES/ADAPTERS/REPAIR
Sort By:
1
SLIP JOINT WASHER 1-1/2 NO2B  World Wide Sourcing 24306 Faucet Coupling Nut Plumb Pak PP20955 Slip Joint Nut
1-1/2". O.D. X 1-1/4". I.D. X 3/16 H. Fits tube size 1-1/4 in. Use Ring #2. Forms a seal which helps prevent leaks. Easy to install. Includes 1 washer. Fits 1/2'' iron pipe faucet shanks. 2 per bag. Plumb Pak Slip Joint Nut, 1-1/2 in Size, PVC, White
Plumb Pak PP25519 Tailpiece Washers Plumb Pak PP20956 Slip Joint Nut TAPE ELECT VNYL BLK 3/4INX60FT
Plumb Pak Tailpiece Washer, Beveled, 1-1/2 in, Polyethylene, For Plastic Drainage Systems Plumb Pak Slip Joint Nut, 1-1/4 in, Plastic, White, For Plastic Drainage Systems Black vinyl electrical tape for common electrical uses. 7 mil., UL Approved.
Intertape 602 Electrical Tape World Wide Sourcing PMB-086 Drain Tailpiece Washers Gardner Bender GSE-15310 Service Entrance Staple
General purpose electrical insulating tape, good dielectric strength. 7 mils thick. UL Listed and CSA Certified. WORLDWIDE SOURCING Drain Tailpiece Washer, Polyethylene, 1-1/2 in ID Secures service entrance cable. Pointed offset legs drive in straight, will not split wood. High quality carbon steel for durability and easy nailing.
Plumb Pak PP25535 Tailpiece Washer World Wide Sourcing 24463 Drain Stoppers Calterm 49305 Electrical Tape 30 ft L x 7.5 mil T
Plumb Pak Poly Washer, Beveled, 1-1/4 in, Polyethylene, For Plastic Drainage Systems Watertight seal. White rubber. Black PVC electrical tape is UL Listed to 600 volt. 7.5 mil. thickness and a temperature rating up to 80 degrees Celsius/176 degrees Fahrenheit. Elongation of 200 percent allows tight wrapping and sealing.
WireGard 19-AWC Assortment Wire Connector Kit WireGard 19-001 Twist-On Wire Connector WireGard 19-002 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WireGard 19-003 Twist-On Wire Connector WireGard 19-004 Twist-On Wire Connector WireGard 19-006 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WingGard 19-084 Twist-On Wire Connector WingGard 19-086 Twist-On Wire Connector Hex-Lok 19-2H2 Hex Lock Wire Connector
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
WingGard 19-089 Twist-On Wire Connector GreenGard 19-095 Grounding Wire Connector Gardner Bender MS-1550T Cable Staple
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable.
Bell Raco 5173-2 Blank Weatherproof Device Cover Bell Raco 5173-1 Blank Weatherproof Device Cover World Wide Sourcing PMB-089 Slip Joint Washer
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Worldwide Sourcing Slip Joint Washer, 1-1/2 in Nominal, Rubber
Plumb Pak PP25515 Drain Tailpiece Washers LOCKNUT SHANK IPS FAUCET 1/2IN WASHER POLY SLIP 1-1/2IN O.D.
Plumb Pak Drain Tailpiece Washer, 1-1/2 in, Polyethylene, For Plastic Drainage Systems Plastic construction, universal design fits standard 1/2? IPS faucet shanks. Attaches to the faucet shanks from underneath the counter. Plastic. No brass friction ring needed.
STOPPER DRAIN RUBBER 1-1/8 WHT STOPPER DRAIN RUBBER 1IN WHITE Gardner Bender MS Cable Staple
Constructed of a stain-proof rubber. Split-type ring allows for bead-chain connection. Constructed of a stain-proof rubber. Split-type ring allows for bead-chain connection. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable.
STRAINER SINK WASHER ASSORT   WASHER POLY SLIP 1-1/4IN O.D. Intertape 85828 Electrical Tape
Includes one rubber washer and one poly washer. 1-3/4" OD x 1-3/8" ID x 1/8 in thick. Universal design. Plastic. No brass friction ring needed. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85827 Electrical Tape Intertape 85835 Electrical Tape Intertape 85830 Electrical Tape
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85832 Electrical Tape Intertape 85831 Electrical Tape World Wide Sourcing PMB-111 Drain Stopper
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. Worldwide Sourcing Drain Stopper, 1-1/8  - 1-1/4 in Fits Size, Rubber, White
STOPPER DRAIN RUBBER 1-1/4 WHT NUT/WASHER SLIPJOINT 1-1/2 WHT STOPPER DRAIN RUBBER 1-3/8 WHT
Constructed of a stain-proof rubber. Split-type ring allows for bead-chain connection. Plastic. Includes washer and nut. No brass friction rings needed. Constructed of a stain-proof rubber. Split-type ring allows for bead-chain connection.
STOPPER DRAIN RUBBER 1-1/2 WHT Gardner Bender MS-1575T Cable Staple Bell Raco 5173-7 Blank Weatherproof Device Cover
Constructed of a stain-proof rubber. Split-type ring allows for bead-chain connection. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated.
Hubbell 5173-5 Blank Weatherproof Cover Hubbell 5173-6 Blank Weatherproof Cover TAILPIECE NUT 1/2IN IPS FAUCET
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Metal construction, 1/2" IPS thread on nut. Universal design fits most faucets.
World Wide Sourcing PMB-095 Faucet Coupling Nuts Erico ESB8 Split Bolt Connector NUT/WASHER SLIPJOINT 1-1/4 WHT
Chrome plated. 1/2" iron pipe size. Silicon bronze for copper to copper. UL Listed. Plastic. Includes washer and nut. No brass friction rings needed.
World Wide Sourcing PMB-105 Drain Stopper Gardner Bender MSI-1525T Insulated Cable Staple Erico ESB6 Blackburn Split Bolt Connectors
Worldwide Sourcing Drain Stopper, 1-1/4 in Fits Size, Rubber, White Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation. Silicon bronze for copper to copper. UL Listed.
Gardner Bender PSG Low Voltage Cable Staple STOPPER DRAIN RUBBER 1-5/8 WHT WASHER/NUT ROSETTE 1/2IN IPS
For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. Split-type ring. White. Plastic nut, 1/2" IPS thread on nut, metal rosette washer. Universal design.
Plumb Pak PP25516 Slip Joint Washer Gardner Bender MSI-50B Insulated Cable Staple World Wide Sourcing PMB-471 Drain Stoppers
Plumb Pak Slip Joint Washer, 1-1/4 in, Rubber, For Water Supplies Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation. Worldwide Sourcing Drain Stopper, 1-5/8 - 1-3/4 in Fits Size, Rubber, White
World Wide Sourcing PMB-110 Drain Stopper NUT/WASHER SLIPJOINT 1-1/2 WHT Gardner Bender PWS Low Voltage Kwik Mount Cable Staple
Worldwide Sourcing Drain Stopper, 1-3/4 in Fits Size, Rubber, White Plastic. Includes washer and nut. No brass friction rings needed. Quick fastening and guiding of wires. Wires easily snap in or out of two usable sides. Use to secure Christmas light sets, sound system wires, etc. Holds category 5 cable for datacom.
Gardner Bender PSB Cable Staple Gardner Bender MS-1555 Cable Staple Gardner Bender GSE-15410 Service Entrance Staple
For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Secures service entrance cable. Pointed offset legs drive in straight, will not split wood. High quality carbon steel for durability and easy nailing.
Gardner Bender GSE-402 Service Entrance Strap Gardner Bender MS Cable Staple Gardner Bender GSE-205 Service Entrance Strap
Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage.
Scotch 4218-BA-40 Electrical Tape Plumb Pak PP22006 Drain Stopper STAPLE METAL INSULATED 1/2IN
Commercial grade 7-mil polyvinyl chloride insulating tape, flame retardant and provides mechanical protection with minimum bulk. Excellent resistance to abrasion, moisture, acids, copper corrosion and varying weather conditions. UL Listed and CSA Certified. White Rubber Metal insulated staples secures and protects non-metallic (NM), BX, MC, AC and UF cable. Insulator made from durable polyethylene. Plastic insulator protects cables and helps prevent arc faults. Dimensions: 1/2"W x 1-1/2"L. Silver/red color.
World Wide Sourcing PMB-104 Drain Stoppers Gardner Bender MSB Insulated Low Voltage Cable Staple Gardner Bender MSW Insulated Cable Staple
Worldwide Sourcing Drain Stopper, 1-1/2 in Fits Size, Rubber, White U-shaped staple fastens audio speaker and bell wire, insulated cradle protects wire. U-shaped staple fastens audio speaker and bell wire, insulated cradle protects wire.
Plumb Pak PP820-1 Drain Stoppers FAUCET HANDLE WHEEL ROUND 12PT Erico ESBP8 Split Bolt Connector Spacer
White Rubber Metal construction. 12pt. round broach. Metallic finish. Designed to fit hose bibb faucets, stopcocks and valves. With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper.
Jandorf 61423 Cord Protector Jandorf 61424 Cord Protector Gardner Bender GSE-304 Service Entrance Strap
Jandorf Cord Protector, Nylon, Black, UL Listed, For Indoor and Outdoor Use Jandorf Cord Protector, Nylon, Black, UL Listed, For Indoor and Outdoor Use Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage.
Jandorf 60935 Closed End Connector 22 - 18 AWG Gardner Bender PS-50 Insulated Cable Staple Calterm 73438 Heat Shrink Tubing Assortment
Jandorf Closed End Connector Series: 60935, 22 - 18 AWG Conductor, Fully Insulated Insulation, Vinyl Insulation, Clear, Tin Plated Copper, UL Listed For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Used to repair and cover torn wire insulation or to protect and insulate objects such as rope ends, plier handles or terminal connections. Wire identification by color. Shrinks up to half of its original diameter and is temperature rated to 221 degrees Fahrenheit and 600 volt maximum, Underwriters Recognized specification UL 224.
Gardner Bender 20-410 Crimp Sleeve Connector Calterm 61470 Assortment Wire Cap Set Jandorf 61415 Cord Protector
Zinc plated steel. Suitable for solid or stranded copper wire. Jandorf Cord Protector, Nylon, Black, UL Listed, For Indoor and Outdoor Use
Jandorf 61416 Cord Protector Danco 35646 Assorted Faucet Handle Screw Gardner Bender GSE-105 Service Entrance Strap
Jandorf Cord Protector, Nylon, Black, UL Listed, For Indoor and Outdoor Use Handle screws for American Standard, Gerber & Price Pfister handles. Includes oval and flat head screws, two No.35639 and two No.35646. Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage.
Gardner Bender PSB Low Voltage Cable Staple WireGard 25-002 Twist-On Wire Connector Gardner Bender PMB-1525 Low Voltage Cable Strap
For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed.
Gardner Bender MS-1577 Cable Staple Gardner Bender PSW-1650T Cable Staple Gardner Bender PCC Low Voltage Clip-On Cable Staple
Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. Used for indoor and outdoor applications. UV resistant polyethylene saddle. Zinc plated nails. Secures RG-49, RG-59 and RG-6 coaxial cables. With clip-on feature.
Jandorf 61417 Cord Protector GB-Gardner Bender MSI-1575 Cable Staples GB PTP-25T Category 3 and 5 Low Voltage Data Staple
Jandorf Cord Protector, Nylon, Black, UL Listed, For Indoor and Outdoor Use Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation. GB Data Staple, Category 3 and 5, Low Voltage, 1/4 in Crown, Polyethylene, Zinc Plated, Blue, Suitable For Use With: RJ-11, RJ-12, RJ-45, Category 3 and Category 5 Wire to Wood, 1/4 in Width, For Mounting to Wood Surfaces
STOPPER DRAIN RUBBER 1-3/4 WHT Gardner Bender GTF-300 Friction Tape WireGard 25-001 Twist-On Wire Connector
Constructed of a stain-proof rubber. Split-type ring allows for bead-chain connection. For use over electrical tape splices. Matted finish provides the best gripping surface available. Use to wrap grips on hand tools. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Plumb Pak PP25509 Slip Nut & Washer GB-Gardner Bender GTB-667P Electrical Tape GB-Gardner Bender GTW-667P Electrical Tape
Plumb Pak Slip Nut, 1-1/4 in, Die Cast, For Brass Drainage Systems Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2.
SLIP JOINT WASHER ASSORTMENT  NUT TAILPIECE 1/2IN IPS FAUCET Erico ESBP6 Split Bolt Connectors
Plastic. No brass friction ring needed. For use with hot or cold water. Connects water supply line to faucet. 1/2" IPS. 2 per card. With spacer bar silicon bronze, electro-tin plated. For aluminum to aluminum, copper to aluminum, copper to copper. Range for equal main and tap 1/16 copper.
Hex-Lok 19-1H1 Hex Lock Wire Connector Gardner Bender PS-75 Insulated Cable Staple Hubbell 5374-0 Blank Round Flat Weatherproof Cover
Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs. For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. For use with 4" round splice boxes. Installation hardware, and gasket included. 4" diameter, shrink wrapped. UL Listed.
Jandorf 61422 Cord Protector Gardner Bender FLX-5007 Corrugated Spilt Flexible Tube GB-Gardner Bender GTO-667P Electrical Tape
Jandorf Cord Protector, Nylon, Black Protects hoses, wire and cables from cuts, abrasions and UV wear. Corrugated for added flexibility. Split down the center for wire breakout where needed. Black. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2.
Calterm 73457 Flexible Tube Gardner Bender 20-411 Crimp Sleeve Connector Danco 88356 Assorted Faucet Handle Screw
Quickly installed over entire length of wire run. Excellent for under hood and trailer wiring. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed. Includes oval and flat head screws, two No.35639, two No.35652, No.35646 No. 35658, and No.35659.
Plumb Pak PP25511 Slip Nuts and Washers Danco 96723 Faucet O-Ring Danco 96724 Faucet O-Ring
Plumb Pak Slip Nut, 1-1/2 in, Die Cast, For Water Supplies #6 - Fits:  Central, Wallaceburg, Kohler, Cuthbert, Mueller, Sloan, Crane, Speakman, Sterling, Waltec, Indiana. 7/16" O.D. x 5/16" I.D. x 1/16" wall. #7 - Fits American Standard, Kohler, Mueller, Powers, Waltec, Watrous, Universal Rundle, Sayco, Michigan Bass, Sears Harmony. 1/2"O.D. x 3/8" I.D. x 1/16" wall.
Plumb Pak PP25517 Slip Joint Washers WireGard 25-003 Twist-On Wire Connector Gardner Bender 20-089 Closed End Crimp Pigtail Connector
Plumb Pak Slip Joint Washer, 1-1/2 in, Rubber, For Water Supplies Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed.
Gardner Bender 20-090 Closed End Crimp Pigtail Connector Gardner Bender PS-1550T Insulated Cable Staple World Wide Sourcing PMB-100-3L Tub Stoppers
Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed. For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Bagged.
Bell Raco 5175-1 Blank Weatherproof Device Cover Plumb Pak PP25535-20 Slip Joint Washer STOPPER FLAT SINK 5IN WHITE
For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". Plumb Pak Slip Joint Washer, Beveled, 1-1/4 in, Polyethylene Rubber. 5" diameter fits most sinks.
Calterm 73458 Flexible Tube Gardner Bender PS-1575T2 Insulated Cable Staple GB-Gardner Bender HST-187R Heat Shrink Tubes
Quickly installed over entire length of wire run. Excellent for under hood and trailer wiring. For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long.
GB-Gardner Bender HST-250R Heat Shrink Tubes GB-Gardner Bender HST-375R Heat Shrink Tubes GB-Gardner Bender HST-500R Heat Shrink Tubes
For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long. For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long. For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long.
GB-Gardner Bender HST-187W Heat Shrink Tubes GB-Gardner Bender HST-250W Heat Shrink Tubes GB-Gardner Bender HST-375W Heat Shrink Tubes
For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long. For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long. For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long.
GB-Gardner Bender HST-500W Heat Shrink Tubes Plumb Pak PP22003 Drain Stopper World Wide Sourcing PMB-102-3L Sink Stoppers
For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long. White Rubber 5". Fits all drains.
Jandorf 61414 Cord Protector GB-Gardner Bender HST-125W Heat Shrink Tubes TUBING H SHRK 3/32-3/64X3 WHT
Jandorf Cord Protector, Nylon, Black, UL Listed, For Indoor and Outdoor Use For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long. For cable insulation, marking and bundling, with superior mechanical, abrasion and moisture protection. Flame retardant, meets UL 224 VW-1. Resists common fluids and solvents. 2:1 shrink ratio. 3 inches long.
Gardner Bender MDI Insulated High Impact Cable Staple Danco 88355 Assorted Faucet Handle Screw Plumb Pak PP20965 Slip Joint Washer
Insulated staples protect and secure Romex, NM, BX and UF. PVC insulation protects cable from damage due to mis-hit and overdriving, prevents a short circuit if wire insulation is damaged. Highly visible color coded for size and application. Card/40. Handle screws for Central, Sayco and Sterling handles. Includes oval head screws, two No.35636, two No.35657 and No.35141. Contains 1 each 1-1/2" x 1-1/2" and 1-1/2" x 1-1/4". Bagged.
Gardner Bender PCS-1600T Low Voltage Masonry Staple Plumb Pak PP25519-20 Slip Joint Washer Jandorf 60820 Closed End Connector 12 - 10 AWG
Hardened nails can penetrate cement block, mortar or plaster surfaces. For cable TV and other hard-surface installation. Plastic cradle provides added protection to cable jackets. Freeze resistant. UV protected. (Black). Secures RG-49, RG-59 and RG-6 coaxial cables. PCS-1600 has clip-on feature. Plumb Pak Slip Joint Washer, Beveled, 1-1/2 in, Polyethylene Jandorf Closed End Connector Series: 60820, 12 - 10 AWG Conductor, Insulated Insulation, Nylon Insulation, Clear, Tin Plated Copper, UL Listed
Danco 80654 Faucet Handle Adapter PushGard 19-PC2 2-Port Push-In Connector Gardner Bender HST-750 Thin Wall Heat Shrink Tubing
Specially designed insert with unique three-point contact provides superior locking to all stems, regardless of size, configuration or damaged condition. Includes Allen wrench. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements.
Danco 35711B Faucet O-Ring Danco 35714B Faucet O-Ring Danco 35719B Faucet O-Ring
#83 - Fits Gerber, American Standard. 1-2"OD x 5/16"ID x 3/32" wall. Individual UPC Bagged. #80 - Fits American Standard, Valley Faucet. 51/64"OD x 41/64"ID x 5/64" wall. Individual UPC Bagged. #74 - Fits Streamway. 39/64"OD x 3/8"ID x 7/64" wall. Individual UPC Bagged.
Gardner Bender FLX-3810 Corrugated Spilt Flexible Tube Gardner Bender HST-093 Thin Wall Heat Shrink Tubing Gardner Bender HST-125 Thin Wall Heat Shrink Tubing
Protects hoses, wire and cables from cuts, abrasions and UV wear. Corrugated for added flexibility. Split down the center for wire breakout where needed. Black. Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements. Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements.
Gardner Bender HST-187 Thin Wall Heat Shrink Tubing Gardner Bender HST-250 Thin Wall Heat Shrink Tubing Gardner Bender HST-375 Thin Wall Heat Shrink Tubing
Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements. Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements. Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements.
Gardner Bender HST-500 Thin Wall Heat Shrink Tubing Gardner Bender HST-999 Thin Wall Heat Shrink Tubing Gardner Bender HST-AST Thin Wall Heat Shrink Tubing Assortment
Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements. Tubing shrinks under heat application to insulate wiring up to half its diameter (finished). Also useful for repairing cords and covering tool handles. Flame retardant. Resists common fluids and solvents. Shrink temperature: 250 degrees F. 2 to 1 shrink ratio. 4" length. UL Listed, meets CSA requirements. Used to repair and cover torn wire insulation or to protect and insulate objects. Includes total of 8 pieces in sizes of 1/8", 3/16" and 1/4" inside diameter before shrinking.
Plumb Pak PP820-3 Drain Stoppers Danco 80788 O-Ring Assortments Danco 35785B Faucet O-Ring
White Rubber Assortment contains: 14 pieces, two each: No.35721, 35724, 35725, 35726, 35728 and 35729. One each: No.35739 and 35748. #72 - Fits Streamway. 19/32"OD x 3/8"ID x 7/64" wall. Individual UPC Bagged.
Danco 35871B Faucet O-Ring Danco 35873B Faucet O-Ring Gardner Bender PSW Low Voltage Cable Staple
#91 - Fits Crane, Kohler. 11/16"OD x 7/16"ID x 1/8" wall. Individual UPC Bagged. #93 - Fits Various. 13/16"OD x 9/16"ID x 1/8" wall. Individual UPC Bagged. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed.
Danco 35750B Faucet O-Ring Danco 35754B Faucet O-Ring Danco 35755B Faucet O-Ring
#36 - Fits American Standard B/C Plunger, Speakman Self-Closing Faucets, Kohler B/C, Waltec. 5/16"OD x 3/16"ID x 1/6" wall. Individual UPC Bagged. #40 - Fits Crane, American Standard, Symmons. 3/4"OD x 5/8"ID x 1/16" wall. Individual UPC Bagged. #41 - Fits Price Pfister, Kohler, Wallaceburg, Waltec. 9/16"OD x 7/16"ID x 1/16" wall. Individual UPC Bagged.
Danco 35761B Faucet O-Ring Danco 35771B Faucet O-Ring Danco 35775B Faucet O-Ring
#47 - Fits Kohler, Flush Valve, Waltec. 11/32"OD x 7/32"ID x 1/16" wall. Individual UPC Bagged. #57 - Fits Crane, Spout, Valley Single Lever, Cuthbert. 1"OD x 13/16"ID x 3/32" wall. Individual UPC Bagged. #61 - Fits Thrush Valves. 9/32"OD x 5/32"ID x 1/16" wall. Individual UPC Bagged.
Danco 35713B Faucet O-Ring Danco 35721B Faucet O-Ring Danco 35722B Faucet O-Ring
#81 - Fits Woodford, Symmons. 1-1/8"OD x 1"ID x 1/16" wall. Individual UPC Bagged. #1 - Fits Western, Crane, Dial-Ese, Kohler, Barnes. 21/32"OD x 13/32"ID x 1/8" wall. Individual UPC Bagged #5 - Fits Cuthbert, Sloan, Speakman, Waltec, Calco, Crane, Kohler, Drinking Fountain, Acme, Schaible, Tracy, Dishmaster. 3/8"OD x 1/4"ID x 1/6" wall. Individual UPC Bagged.
Danco 35724B Faucet O-Ring Danco 35742B Faucet O-Ring Danco 35745B Faucet O-Ring
#7 - Fits American Standard, Kohler, Mueller, Powers, Waltec, Watrous, Universal Rundle, Sayco, Michigan Bass, Sears Harmony. 1/2"OD x 3/8"ID x 1/16" wall. Individual UPC Bagged. #28 - Fits Delta Diverter Assembly, Cuthbert, Kohler. 5/8"OD x 1/2"ID x 1/16" wall. Individual UPC Bagged. #31 - Fits Crane Magic-Close, Eljer, Delta (Delex). 9/16"OD x 5/16"ID x 1/8" wall. Individual UPC Bagged.
Danco 35743B Flat Water Resistant Faucet O-Ring PushGard 19-PC3 3-Port Push-In Connector Arrow Hart S2962 Weatherproof Cover
#29 - Fits Delta Cam Assembly, Symmons. 1-1/4"OD x 1-1/8"ID x 1/16" wall. Individual UPC Bagged. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Tough plastic construction, resistant to high impact and sunlight. Non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Self closing cover. Vertical only. UL Listed for wet locations with cover closed.
Hubbell 5175-5 Blank Weatherproof Cover Hubbell 5180-0 Weatherproof Device Cover Plumb Pak PP22004 Tub Stopper With Plated Ring
For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. White rubber with plated ring.
WingGard 25-084 Twist-On Wire Connector Gardner Bender MSI Insulated Cable Staple Gardner Bender PR Low Voltage Cable Staple
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed.
Danco 35770B Faucet O-Ring Danco 35870B Faucet O-Ring Danco 35872B Faucet O-Ring
#56 - Fits Valley Single Lever, Jameco, Waltec. 1-1/2"OD x 1-3/8"ID x 1/16" wall. Individual UPC Bagged. #90 - Fits Streamway. 1/2"OD x 1/4"ID x 1/8" wall. Individual UPC Bagged. #92 - Fits Various. 3/4"OD x 1/2"ID x 1/8" wall. Individual UPC Bagged.
Danco 35874B Faucet O-Ring Danco 35875B Faucet O-Ring Danco 35748B Faucet O-Ring
#94 - Fits Moen, Various. 7/8"OD x 5/8"ID x 1/8" wall. Individual UPC Bagged. #95 - Fits Various. 15/16"OD x 11/16"ID x 1/8" wall. Individual UPC Bagged. #34 - Fits Moen 42E, Delta, Sloan, Symmons. 1-1/2"OD x 1-1/4"ID x 1/8" wall. Individual UPC Bagged.
Danco 35749B Faucet O-Ring Danco 35756B Faucet O-Ring Danco 35759B Faucet O-Ring
#35 - Fits American Standard Single Control (Push/Pull), Harcraft, Sayco, Waltec. 11/16"OD x 9/16"ID x 1/16" wall. Individual UPC Bagged. #42 - Fits Gyro, Moen (Hard Compound). 11/16"OD x 1/2"ID x 3/32" wall. Individual UPC Bagged. #45 - Fits Sloan, Delta (Delex). 1-3/8"OD x 1-3/16"ID x 3/32" wall. Individual UPC Bagged.
Danco 35762B Faucet O-Ring Danco 35767B Faucet O-Ring Danco 35768B Faucet O-Ring
#48 - Fits Steamway. 5/8"OD x 3/8"ID x 1/8" wall. Individual UPC Bagged. #53 - Fits American Standard Push/Pull Lavatory, Cuthbert. 3/4"OD x 5/8"ID x 3/64" wall. Individual UPC Bagged. #54 - Fits American Standard Push/Pull Bath. 11/16"OD x 9/16"ID x 1/16" wall. Individual UPC Bagged.
Danco 35774B Faucet O-Ring Danco 35715B Faucet O-Ring Danco 35731B Faucet O-Ring
#60 - Fits Minneapolis-Honeywell Control. 1/4"OD x 1/8"ID x 1/16" wall. Individual UPC Bagged. #78 - Fits Carefree, Universal Rundle, Streamway. 7/16"OD x 1/4"ID x 3/32" wall. Individual UPC Bagged. #14 - Fits Union Brass, Youngstown, Indiana, Kohler, American Standard, McDonald, Speakman, Wm. Harvey, Sayco, Gopher, Gerber, Cuthbert, Valley. 15/16"OD x 3/4"ID x 3/32" wall. Individual UPC Bagged.
Danco 35732B Faucet O-Ring Danco 35733B Faucet O-Ring Danco 35734B Faucet O-Ring
#15 - Fits Crane. 1"OD x 3/4"ID x 1/8" wall. Individual UPC Bagged. #16 - Fits Moen, American Kitchens, Crosley, Youngstown, Eljer, Gyro, and Hotpoint. 1-1/16"OD x 13/16"ID x 1/8" wall. Individual UPC Bagged. #17 - Fits Youngstown, American Kitchens, Alamark, Crosley, American Standard, Speakman, Sterling, Schaible. 1-1/16"OD x 7/8"ID x 3/32" wall. Individual UPC Bagged.
Danco 35736B Faucet O-Ring Danco 35737B Faucet O-Ring Super 33+ 195NA Electrical Tape
#19 - Fits Speakman Groen, Zum. 1-1/4"OD x 1"OD x 1/8" wall. Individual UPC Bagged. #20 -Fits  American Standard, Static-Seal for Aqua-Seal, Alamark, Eljer, Jameco, Speakman, Teck. 1-3/16"OD x 1"ID x 3/32" wall. Individual UPC Bagged. For insulating, repairing and protecting electrical wire. UL Listed.
Danco 35741B Faucet O-Ring Danco 35740B Faucet O-Ring Danco 35739B Faucet O-Ring
#27 - Fits Tracy, Moen 42E, Alamark, Harcraft, Repcal, Sterling Faucet, Delta (Delex). 1-1/8"OD x 7/8"ID x 1/8" wall. Individual UPC Bagged. #26 - Fits American Standard, Schaible, Youngstown, Single Lever, Cuthbert, Waltec. 1-3/16"OD x 1-1/16"ID x 1/16" wall. Individual UPC Bagged. #25 - Fits Delta, Single, Lever, Valley. 1-1/2"OD x 1-5/16"ID x 3/32" wall. Individual UPC Bagged.
Danco 35744B Faucet O-Ring Danco 35747B Faucet O-Ring Hubbell 5180-6 Weatherproof Device Cover
#30 - Fits Kohler, American Standard, Speakman, Symmons, Waltec, Teck. 7/8"OD x 3/4"ID x 1/16" wall. Individual UPC Bagged. #33 - Fits Kohler, American Standard, Single Control Push/Pull) Sayco, Harcraft, Speakman, Symmons. 1-1/16"OD x 15/16"ID x 1/16" wall. Individual UPC Bagged. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
PushGard 19-PC4 4-Port Push-In Connector