Home > PLUMBING > KITCHEN & BATH > FIXTURES > BAR SINKS
Choose a sub category:
FISH TAPES CONDUIT BENDERS WIRE STRIPPERS & CRIMPING TOOL
CIRCUIT/VOLTAGE TESTERS FUSE PULLERS LIGHT BULB CHANGERS
ALLIGATOR CLIPS GREENLEE SPECIALTY TOOLS/ACCES MISC TOOLS & ACCESSORIES
Sort By:
1
Halex 97521 Insulated Conduit Bushing Halex 97522 Insulated Conduit Bushing Halex 97525 Insulated Conduit Bushing
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 96191 Rigid IMC Conduit Locknut Halex 96821 Rigid Reducing Conduit Washer Halex 97523 Insulated Conduit Bushing
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 96071 Knock Out Seals Halex 96831 Rigid Reducing Conduit Washer Halex 96832 Rigid Reducing Conduit Washer
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
Carlon A240D-CAR 1-Piece Conduit Coupling Halex 96072 Knock Out Seals Halex 96192 Rigid IMC Conduit Locknut
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 26190 Conduit Locknut Halex 97524 Insulated Conduit Bushing Halex 96193 Rigid Conduit Locknut
Halex Conduit Locknut, 1/2 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 90701 Conduit Chase Nipple Carlon A243D-CAR 1-Piece Snap-In Conduit Adapter Carlon A253E-CAR 1-Piece Snap-In Terminal Adapter
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Halex 96843 Rigid Reducing Conduit Washer Halex 91321 Reducing Conduit Bushing Carlon A253D-CAR 1-Piece Snap-In Terminal Adapter
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
WASHER RDUCNG RGD 1-1/4X1/2IN WASHER RDUCNG RGD 1-1/4X3/4IN Halex 96194 Rigid IMC Conduit Locknut
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Carlon A240E-CAR 1-Piece Conduit Coupling Halex 91641 Box Spacer Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
WASHER RDUCNG RGD 1-1/2X1/2IN WASHER RDUCING RGD 1-1/2X3/4IN Halex 96195 Rigid Conduit Locknut
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 91331 Reducing Conduit Bushing Halex 16405B Box Spacer Halex 91332 Reducing Conduit Bushing
Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved.
Bell Raco 5173-2 Blank Weatherproof Device Cover Bell Raco 5173-1 Blank Weatherproof Device Cover Halex 64005 Conduit Coupling
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 26071 Knock Out Seals Halex 97526 Insulated Conduit Bushing Halex 90702 Conduit Chase Nipple
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Bell Raco 5173-7 Blank Weatherproof Device Cover Hubbell 5173-5 Blank Weatherproof Cover Hubbell 5173-6 Blank Weatherproof Cover
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated.
Halex 96401 Conduit Coupling Halex 16407B Box Spacer Halex 96196 Rigid IMC Conduit Locknut
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
GB-Gardner Bender 14-075 Alligator Clips GB-Gardner Bender 14-077 Alligator Clips Halex 75225 Insulated Conduit Bushing
For home, auto and marine applications. For home and auto applications. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
GB-Gardner Bender 14-078 Alligator Clips Halex 01925B IMC Conduit Locknut Halex 96402 Conduit Coupling
For home, auto and marine applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Bulk packed. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Hubbell 5374-0 Blank Round Flat Weatherproof Cover Halex 90703 Conduit Chase Nipple Bell Raco 5175-1 Blank Weatherproof Device Cover
For use with 4" round splice boxes. Installation hardware, and gasket included. 4" diameter, shrink wrapped. UL Listed. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2".
Halex 75230 Insulated Conduit Bushing Halex 64010 Conduit Coupling Halex 26073 Knock Out Seals
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
GB-Gardner Bender 14-076 Alligator Clips Arrow Hart S2962 Weatherproof Cover Hubbell 5175-5 Blank Weatherproof Cover
For home, auto and marine applications. Tough plastic construction, resistant to high impact and sunlight. Non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Self closing cover. Vertical only. UL Listed for wet locations with cover closed. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2".
Halex 07012 Conduit Chase Nipple Hubbell 5180-0 Weatherproof Device Cover Halex 64405 Conduit Elbow
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Hubbell 5180-6 Weatherproof Device Cover LOCK NUT SEALER 1/2IN         Bell Raco 5175-0 Blank Weatherproof Device Cover
LOCK NUT SEALER 1/2IN
Our Price: $3.36
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2".
Halex 26074 Knock Out Seals Halex 64012 Conduit Coupling WASHER REDUCING 2X1IN
WASHER REDUCING 2X1IN
Our Price: $3.60
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
WASHER REDUCING 2X1-1/4IN     Bell Raco 5180-1 2-Hole Weatherproof Device Cover Halex 94105 Pull Conduit Elbow with Neoprene Gasket
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Bell Raco 5180-2 2-Hole Weatherproof Device Cover GLOWSTICK MINI LED WHITE      GLOWSTICK MINI LED BLUE
GLOWSTICK MINI LED BLUE
Our Price: $3.84
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Sleek design and a simple twist on/off function. Batteries last over 60 hours and can be easily replaced. Waterproof and equipped with a number 0 S-Biner. Waterproof, they float. 4x replaceable AG-3 batteries included. Sleek design and a simple twist on/off function. Batteries last over 60 hours and can be easily replaced. Waterproof and equipped with a number 0 S-Biner. Waterproof, they float. 4x replaceable AG-3 batteries included.
GLOWSTICK MINI LED RED        GLOWSTICK MINI LED GREEN      Hubbell 5180-5 Weatherproof Device Cover
GLOWSTICK MINI LED RED
Our Price: $3.84
Sleek design and a simple twist on/off function. Batteries last over 60 hours and can be easily replaced. Waterproof and equipped with a number 0 S-Biner. Waterproof, they float. 4x replaceable AG-3 batteries included. Sleek design and a simple twist on/off function. Batteries last over 60 hours and can be easily replaced. Waterproof and equipped with a number 0 S-Biner. Waterproof, they float. 4x replaceable AG-3 batteries included. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
Bell Raco 5180-7 2-Hole Weatherproof Device Cover Halex 26075 Knock Out Seals Gardner Bender 14-630 Battery Clamp
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. For battery, battery charger and testing equipment applications. Copper clad clamps. Handle grips are insulated and color-coded for positive (red) and negative (black) identification.
Halex 58305 Rigid Threaded Conduit Body with Cover and Gasket Halex 58405 Rigid Threaded Conduit Body with Cover and Gasket Halex 58605 Rigid Threaded Conduit Body with Cover and Gasket
Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved.
Bell Raco 5152-0 Weatherproof Device Cover Halex 58905 Rigid Threaded Conduit Body with Cover and Gasket Halex 64505 Conduit Elbow
State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Installation hardware, gasket, multi-lingual instructions included. For single 1.406" diameter receptacle. UL Listed for wet location with cover closed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. To connect EMT conduit together to allow for 45 degree bends.
Hubbell 5155-5 Single Device Cover Halex 64507 Conduit Elbow Bell Raco 5155-6 Round Opening Weatherproof Device Cover
With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated. To connect EMT conduit together to allow for 45 degree bends. With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated.
Halex 07015 Conduit Chase Nipple Arrow Hart S1962W-SP Weatherproof Cover Arrow Hart S1961 Weatherproof Cover
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2". Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations.
Arrow Hart S1962 Utility Halogen Low Profile Weatherproof Cover Halex 61820B IMC Sealer Locknut Arrow Hart S1961W-SP Weatherproof Cover
Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2". Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations.
Halex 59505 Service Entrance Elbow Gardner Bender GET-3100 Voltage Tester Gardner Bender RTL-108 Replacement Medium Test Lead
Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. Test for presence of voltage in live circuits. Tests AC/DC voltage from 80-250 volts. The neon indicator glows when voltage is present and brightens as voltage increases. Insulated housing and 2 inch test leads. Built in pocket clip. Tests DC motors, switches and outlets. With detailed user instructions. Replacement leads for Gardner Bender meters GMT-12A, GMT-18A. UL recognized. Tough ABS Plastic. Flexible cords for easy use.
Halex 04010 Offset Nipple Halex 64407 Conduit Elbow Eveready Economy 3151LBP Flashlight
Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Economy flashlight, anti-roll design, ribbed casing for strength and a non-slip grip. Contoured slide switch. Lifetime white LED never needs replacing. Operates for 40 hours using 1 Eveready super heavy duty D-size battery. 9 lumens with a beam distance of 57 meters. Typical weight of 62 grams without battery. 160mm length x 40mm diameter. Assembled in the USA. Red, blue green and orange colors. Do not specify color.
Halex 64015 Conduit Coupling Halex 58805 Rigid Threaded Conduit Body with Cover and Gasket Halex 94107 Pull Conduit Elbow
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Halex 21642 Box Spacer Bell Raco 5103-0 1-Hole Weatherproof Device Cover Bell Raco 5103-1 1-Hole Weatherproof Device Cover
GFCI VERT 1G COVER GRAY
Our Price: $4.88
Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped.
Bell Raco 5103-2 1-Hole Weatherproof Device Cover Halex 64105 Conduit Elbow Carlon E98TSCN-CAR Weatherproof Device Cover
Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Weatherproof cover for single toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified.
Bell Raco 5146-0 1-Hole Weatherproof Device Cover Halex 26076 Knock Out Seals Cooper BP914 Circuit Tester
Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. For testing electric circuits from 90 to 600 volt. Detects presence of power on either AC or DC circuits. Identifies circuit conductors.
Gardner Bender GET-3202 Low Voltage Voltage Tester Dorcy 41-2461 Flashlight With Battery Carlon E98DHGN-CAR Weatherproof Cover
Tests AC/DC voltage from 5-50 volt. Glows when voltage is present and brightens as voltage increases. Insulated alligator clip tests leads. UL Listed. Carded. LED deluxe flashlight, side barrel slide switch. 25 lumens, 10 hours, 50 meters beam distance. 6" length x 1" width. Red / blue colors. Uses 2 AA batteries, included. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed.
Halex 64320 Conduit Nipple Hubbell 5101-6 Weatherproof Device Cover Energizer ENL33AE Compact Pocket Flashlight
Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. LED bulb never needs replacing. Uses 3 AAA Energizer alkaline batteries, included. Compact to fit in pocket or purse, puts out 8 lumens of light for 60 hours.
Hubbell 5121-5 Weatherproof Device Cover Maglite ASXD026 Mounting Bracket Bell Raco 5146-5 Weatherproof Device Cover
For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. Brackets and mounting screws to hold D size Maglite. Made in the USA. Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated.
Halex 95212B Insulated Metallic Grounding Conduit Bushing with Lug Halex 58907 Rigid Threaded Conduit Body with Cover and Gasket Halex 04012 Offset Nipple
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Bell Raco 5101-2 1-Hole Weatherproof Device Cover Bell Raco 5101-1 1-Hole Weatherproof Device Cover Bell Raco 5101-0 1-Hole Weatherproof Device Cover
For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Halex 58607 Rigid Threaded Conduit Body with Cover and Gasket Bell Raco 5121-1 Weatherproof Switch Cover Toolbasix JL-SST-401183L Cable Crimper
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. Cuts and strip wires, crimps ignition terminals. Easy-to-read wire size markings.
Hubbell 5101-5 Weatherproof Device Cover Bell Raco 5101-7 1-Hole Weatherproof Device Cover FLASHLIGHT LED RUBBER 1D
For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. Super tough rubber construction. Water resistant. Uses 1 D cell battery (included).
Halex 58307 Rigid Threaded Conduit Body with Cover and Gasket Halex 58407 Rigid Threaded Conduit Body with Cover and Gasket Carlon E98GFCN-CAR Weatherproof Device Cover
Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. 2.63" high x 1.31" wide opening.
Carlon E98SSCN-CAR Weatherproof Cover Carlon E98GDRN-CAR Weatherproof Device Cover Carlon E98G5FN-CAR Weatherproof Cover
Non-conductive. Suitable for wet locations. Gaskets and screws included. UL Listed. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. For 50 amp twist lock single receptacles under 2.250" diameter. For exposed applications. Will not rust or corrode. Gaskets and screws included. UL Listed.
Wire-Aide 79-006N Non-Toxic Wire Pulling Lubricant Halex 07020 Conduit Chase Nipple Milwaukee Clipper GS-40 Adjustable Wire Cutter/Stripper
Heavy cream-like paste. Slides on smoothly and clings throughout the pull. Excellent abrasion protection and cling ability, repels water to some extent. Modified wax base formula dries to a slippery film. Greaseless, non-toxic, will not stain skin, clothing or construction trim; cleans up with soap and hot water. Withstands normal temperature extremes and will not dry out in the container. Remains stable with 3 freeze-thaw cycles. Non-combustible, non-conductive and non-corrosive. Will not damage conduit or insulation. Suitable for fiber-optic wire. Yellow color. In a squeeze bottle. UL Listed. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Includes spring return and lock. Adjustable, hardened spring steel. Strips 10-24 gauge wire.
Halex 64107 Conduit Elbow Halex 59507 Service Entrance Elbow Arrow Hart S3966W-SP Decorative Weatherproof Cover
Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. For GFCI/Decorator receptacle used in wet locations. Gaskets provided to seal cover edges as well as device openings. Stainless steel mounting screws included. Horizontal flush or surface mount. UL Listed.
Eveready 1251L Industrial Flashlight Halex 64410 Conduit Elbow Arrow Hart S2966W-SP Decorative Weatherproof Cover
LED bulb never needs to be replaced. Impact-resistant housing. Built-in hanger ring. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Plastic, impact and sunlight resistant. Gaskets provided to seal cover edges as well as device openings. Self closing cover. Stainless steel mounting screws furnished. Vertical, flush or surface mount. UL Listed.
Arrow Hart S2966 Decorative Weatherproof Cover Arrow Hart S3966 Decorative Weatherproof Cover RECPTCL/CVR DPLX HRZ WP GRY 1G
Plastic, impact and sunlight resistant. Gaskets provided to seal cover edges as well as device openings. Self closing cover. Stainless steel mounting screws furnished. Vertical, flush or surface mount. UL Listed. For GFCI/Decorator receptacle used in wet locations. Gaskets provided to seal cover edges as well as device openings. Stainless steel mounting screws included. Horizontal flush or surface mount. UL Listed. Used where weatherproof protection is required for an outdoor receptacle. Self-closing lids. Powder coat finish. Size 4-1/2" width x 2-3/4" length. Includes gasket and mounting hardware. UL Listed, NEMA 3R Rated.
Carlon E98SRCN-CAR Weatherproof Cover FLASHLIGHT LED GEL-BRITE 2AA  Eveready Economy 3151L2S Flashlight
For 15 amp or other single receptacles under 1.375" diameter. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. Rubber flashlight. 40 hour run time, 50 meter beam distance, uses 2 AA batteries, included. 6.20" L x 1.14" W, 3.1 oz. Push button switch. Blue, red, purple and green colors. Economy flashlight, anti-roll design, ribbed casing for strength and a non-slip grip. Contoured slide switch. Lifetime white LED never needs replacing. Operates for 40 hours using 1 Eveready super heavy duty D-size battery. 9 lumens with a beam distance of 57 meters. Typical weight of 62 grams without battery. 160mm length x 40mm diameter. Assembled in the USA. Red, blue green and orange colors. Do not specify color.
Halex 58807 Rigid Threaded Conduit Body with Cover and Gasket BUSHING GRND MTL INSUL 1-1/4IN Gardner Bender GTPS-3100 Cable Stripper
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Strips UTP and STP cable up to .24" (6.2mm) OD. Tension release lever, compact design. For use on CAT 3 and CAT 5 cable. Carded.
Gardner Bender GRT-3500 Outlet Tester Bell Raco 5141-0 Weatherproof Switch Cover GB CR-1000 Cable Ripper
Tests standard receptacles and extension cords to ensure proper wiring. Neon indicators give positive indication of circuit status. Compact unit simply plugs into any standard 3-wire/grounded receptacle or extension cord (110 /125 volt circuits). Tests for six circuit conditions: open ground, open neutral, open hot, hot/ground reverse, hot/neutral reverse and correct wiring. Yellow and red lights provides indication of circuit status or specifies wiring errors. Weatherproof protection for an "on-off" type switch. Vertical, mounted to device. Rugged die cast construction, powder coat finish. Self-closing lid assures weatherproof protection when not in use. Supplied with a switch - no need to purchase separate components. Switch is unassembled to the cover. UL, CSA and NEMA 3R rated. Shrink wrapped. GB Cable Ripper, Premium, 14 - 6 AWG Cable/Wire, 4 in Overall Length, cULus Listed, For Use to Cut Off Cable Jacket
Gardner Bender GET-213HV High Visibility Dual Indicator Voltage Tester Halex 99526 Insulated Metallic Grounding Conduit Bushing with Lug Arrow Hart S992 Weatherproof Cover
Large, dual, neon indicators acknowledge presence of voltage. Individual indicators for each voltage range assures reliability of testing. Probes snap on bottom of housing for single hand testing of outlets. Insulated leads and housing. Tests from 100 to 300 volt AC/DC. UL Listed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. For single devices, take either single receptacle or switch. Corrosion resistant materials suitable for exposure to weather. Gaskets provided to seal cover edges and openings. Mount on flush or surface single gang boxes. Gray color. UL Listed. Polybagged.
Bell Raco 5141-5 3-Way Weatherproof Cover Gardner Bender GET-3213 3-Range Voltage Tester Energizer PLED23AEH Penlight
For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. Three-way live circuit tester indicates 120, 240 and 277 volt AC. UL Listed. Aluminum silver body, push button tail switch for one handed operation and a sturdy clip. One super bright lifetime LED, 6 lumens and over 100 hours run time with 2 AAA alkaline batteries, included. Typical weight is 1.5 oz. with batteries. 5.720" x 0.659".
Halex 64020 Conduit Coupling GB-Gardner Bender CT6101 Continuity Testers GB-Gardner Bender SK-632T Electrician Screw Kits
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Tests for breaks in non-energized wires or cords. 360 degree visual indication. Durable, heavy-duty tip. Flexible lead with insulated alligator clip. Pocket clip. Operates from 2 AAA batteries (included). Contains assorted sizes and lengths of commonly used electrical screws. Screws are #6 - 32, ranging from 3/4" to 3" in length.
Carlon E9G2SSNR Weatherproof Cover Carlon Code Keeper Red Dot CKNM-NG Weatherproof Cover Halex 04015 Offset Nipple
Weather resistant cover for double toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified. Accepts GFCI, duplex, switch and up to 1-3/8" round devices. Nonconductive, noncorrosive, and impact resistant. Won't rust or fade. Scratch resistant. For use in wet/damp locations. Keyhole mounts, loosen the existing device screws and slide the cover over. Comes with adapter plates and pre-adhered gaskets. Wasp guard included to keep out unwanted pests. Lockable for security. UL Listed. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Gardner Bender ET6204 4-Range High Visibility Voltage Tester Arrow Hart S989-SP Weatherproof Cover FLASHLIGHT 9 LED NOBREAK 3AAA
Compact ergonomic design. Hi-impact ABS housing. Visual voltage indication. Snap-in leads are spaced to fit a standard outlet for easy, hands-free testing. Tests for voltage at 120 volt, 240 volt, 277 volt and 480 volt. With pocket clip. cULus Listed. Corrosion resistant materials suitable for exposure to weather. Gaskets provided to seal cover edges and openings. Corrosion resistant mounting screws included. Mount on flush or surface single gang boxes. UL Listed. Industrial 9 LED flashlight. 42 lumens, 15 hours, 32 meters. Uses 3 AAA batteries, (Included). Plastic. 4.04" L x 1.06" W, .5lb. Push button tail cap. Weather resistant, carabiner hang ring. Shatterproof construction, lanyard.
GB SK-832T Electrician's Screw Kit Halex 58610 Rigid Threaded Conduit Body with Cover and Gasket Halex 95215B Insulated Metallic Grounding Conduit Bushing with Lug
GB Screw Kit, Electrician's, 120 Pieces, Includes: (20) 2/3 in, (20) 7/8 in, (20) 1 in, (20) 1-1/4 in, (20) 1-5/8 in and  (20) 2 in  Phillips Head Screws, NO 8-32 Phillips Round Head, For Switches, Receptacles and Outlet Applications Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Halex 64412 Conduit Elbow Energizer FNL2BU1CS Trim Flexible Neck Light FLASHLIGHT LED TRAFFIC CONE 2D
To connect EMT conduit together to allow for 90 degree bends. UL Approved. White LED. Hands free multi-position flexible neck, slide switch, 30 hour runtime on two CR2032 lithium coin cells, included. Large spring clip. On/off switch. Features a durable safety cone attachment. With safety cone. 30 lumen, 24 hour run time, 32 foot beam distance, uses 2 D batteries, not included. 13.77"L x 2.35"W.
Gardner Bender GFI-3501 Manual Outlet Tester Bell Rayntite 5034-0 Weatherproof Device Cover Halex 95220B Insulated Metallic Grounding Conduit Bushing with Lug
Tests ground fault breakers by overloading circuit and tripping GFCI. Plug tester into any ground fault receptacle (110-125 volt AC) and press black button to overload circuit. Tests for seven conditions; ground fault interruption, open ground, open neutral, open hot, hot/ground reverse, hot/neutral reverse and correct wiring. Yellow and red lights provide indication of circuit status or specify which wire is defective. Carded. For weatherproof 30-50 amp receptacles and wet locations. 2.625" diameter. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when the receptacle is not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated. Shrink wrapped. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
LOCK NUT SEALER 2IN           Solitaire K3A116 Water Resistant Flashlight Solitaire K3A016 Water Resistant Flashlight
LOCK NUT SEALER 2IN
Our Price: $8.40
Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Constructed of high-strength aluminum exterior components. Adjusts  from a diffused to a pinpoint light. Spare bulb in the tail cap. With key lead accessory. Single cell AAA premium alkaline battery included. Constructed of high-strength aluminum exterior components. Adjusts  from a diffused to a pinpoint light. Spare bulb in the tail cap. With key lead accessory. Single cell AAA premium alkaline battery included.
Solitaire K3A036 Water Resistant Flashlight FLASHLIGHT 6 LED 3AA          Gardner Bender GS-366 Cable Crimper/Stripper
Constructed of high-strength aluminum exterior components. Adjusts  from a diffused to a pinpoint light. Spare bulb in the tail cap. With key lead accessory. Single cell AAA premium alkaline battery included. Weather resistant. Tail cap push button switch. 135 lumens, 2 hour run time, uses 3 AAA batteries, included. Plastic, 3.93" L x 1.32" W, .20lb. black/blue/green/orange colors. Strips cable, 10-22 AWG wire, crimps terminals and cuts bolts. Easy-to-read wire size markings.
Halex 59510 Service Entrance Elbow FLASHLIGHT SMALL 150LUMEN     Gardner Bender GCT-3304 Low Voltage Twin Probe  Continuity Tester
Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. LED Flashlight. Economy continuity tester, tests continuity in nonenergized circuits. Features 36" insulated lead with alligator clip end. Fully shielded indicator bulb lights to indicate continuity, Uses 2 AA batteries, not included.
Halex 64110 Conduit Elbow Solitaire K3AMW6 Water Resistant Flashlight Gardner Bender GCV-3206 Low Voltage Twin Probe Continuity Tester
Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. With National Breast Cancer Foundation (NBCF) logo, pink, with pink key lead and 1-AAA battery in blister packaging. Can be seen for 20 meters. Battery lasts 3 hours and 45 minutes. Weather resistant, 1 meter drop resistant. For key chains and handbags. A USA manufacturer. Test continuity without wire probes on non-energized circuits. Tests AC/DC voltage from 12 to 250 volts on energized circuits. Glows when voltage or continuity exists. Uses 2 button batteries, included. UL Listed. Carded.
Hubbell 5148-5 Weatherproof Device Cover Eveready EVINL25S Industrial Flashlight Halex 29523 Insulated Metallic Grounding Conduit Bushing with Lug
Waterproof protection for outside receptacle. Self-closing lids. Installation hardware, gasket, and multi-lingual instructions included. Size: 4-1/2" width x 4-1/2" length. C/UL/US UL 514-A listed, CSA and NEMA 3R rated. Constructed from non-conductive material, making it ideal for wet areas. Built-in hanger ring. Light and compact, it fits easily in any toolbox. An impact-resistant housing reduces the chance of breakage from dropping and abuse and the chemical-resistant polypropylene body protects it from staining and corrosion. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Bell Rayntite 5030-0 Weatherproof Cover Bell Raco 5148-0 Weatherproof Device Cover Dorcy 41-2350 Work Light with Battery
For 30-50 amp receptacles, 2.150" diameter. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL listed NEMA 3R rated. Waterproof protection for outside receptacle. Self-closing lids. Installation hardware, gasket, and multi-lingual instructions included. Size: 4-1/2" width x 4-1/2" length. C/UL/US UL 514-A listed, CSA and NEMA 3R rated. Weather resistant, made with high impact resins, rubberized push button switch, head and tail cap. Super bright LED. Springless design system. Batteries included.
Halex 94110 Pull Conduit Elbow with Neoprene Gasket Rayntite 5028-5 Weatherproof Device Cover Bell Rayntite 5028-6 Weatherproof Weatherproof Device Cover
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. For outdoor GFCI receptacles and wet locations. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. 4-1/2" length x 2-3/4" width. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated. For outdoor GFCI receptacles and wet locations. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. 4-1/2" length x 2-3/4" width. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated.
Carlon E9G2DSN-CAR Weatherproof Device Cover Bell 5145-0 Weatherproof Cover 4-1/2 in L x 4-9/16 in W Gardner Bender GS-385 Multi-Function Long Nose Plier
For two gang duplex receptacles and weatherproof toggle switch applications. Cast cover for use whenever weatherproof protection is required for an outdoor receptacle. Heavy duty metallic construction will last the life of the installation. Self closing lids assure weatherproof protection when the receptacle is not in use. Comes with installation instructions, gasket and hardware. UL, CSA Compliant. Multi-function long nose pliers cut, strip and crimp. Use needle nose to form wire or grip small parts. Strips number 14 - number 16 AWG solid or stranded wire. Crimps insulated terminals up to number 10 AWG. Cuts solid or stranded wire. Serrated jaw and cushioned grips.
Powerzone FT-ORG12 Flashlight Bell Raco 5157-0 Round Weatherproof Device Cover Fulcrum MultiFlex Read/Task Light
LED never needs replacing, has low power consumption for longer battery life. Eveready heavy-duty batteries included. Powder coat finish and scratch resistant. Weatherproof protection for outdoor receptacles. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. 2 single, 1.406" diameter receptacle openings. C/UL/US UL 514-A listed, CSA C22.2 No. 18, NEMA 3R Rated. Shrink pack. LED light, multiflex series. Metal flex neck. Uses 3 AAA batteries, not included. For clamps or stands, hands free solution.
Mintcraft CP-C8153L Multi Function Wire Stripper Halex 58810 Rigid Threaded Conduit Body with Cover and Gasket