Home > PLUMBING > KITCHEN & BATH > FIXTURES > VANITIES
Choose a sub category:
FULLY ASSEMBLED/PREASSEMBLED RTA/UNASSEMBLED
Sort By:
1
Halex 97521 Insulated Conduit Bushing Halex 97522 Insulated Conduit Bushing Halex 97525 Insulated Conduit Bushing
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 96191 Rigid IMC Conduit Locknut Halex 96821 Rigid Reducing Conduit Washer Halex 97523 Insulated Conduit Bushing
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 96071 Knock Out Seals Halex 96831 Rigid Reducing Conduit Washer Halex 96832 Rigid Reducing Conduit Washer
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
Carlon A240D-CAR 1-Piece Conduit Coupling Halex 96072 Knock Out Seals Halex 96192 Rigid IMC Conduit Locknut
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 26190 Conduit Locknut Halex 97524 Insulated Conduit Bushing Halex 96193 Rigid Conduit Locknut
Halex Conduit Locknut, 1/2 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 90701 Conduit Chase Nipple Carlon A243D-CAR 1-Piece Snap-In Conduit Adapter Carlon A253E-CAR 1-Piece Snap-In Terminal Adapter
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Halex 96843 Rigid Reducing Conduit Washer Halex 91530 Combination Coupling Halex 90510 Twin Screw Clamp Connector
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Zinc die cast. Use to join EMT conduit to non-metallic sheathed cable. #14/2, #12/3 or 2 #14/2. Indoor use only. With UPC. UL Approved. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements.
Halex 91321 Reducing Conduit Bushing Carlon A253D-CAR 1-Piece Snap-In Terminal Adapter WASHER RDUCNG RGD 1-1/4X1/2IN
Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
WASHER RDUCNG RGD 1-1/4X3/4IN Halex 96194 Rigid IMC Conduit Locknut Carlon A240E-CAR 1-Piece Conduit Coupling
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Duracell PX76A675PK Non-Rechargeable Cylindrical Alkaline Battery Halex 91641 Box Spacer Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter
Lasts longer in electronic devices. Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
Halex 96510 2-Piece Butterfly Clamp Connector WASHER RDUCNG RGD 1-1/2X1/2IN WASHER RDUCING RGD 1-1/2X3/4IN
Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
Halex 96195 Rigid Conduit Locknut Halex 91331 Reducing Conduit Bushing Halex 16405B Box Spacer
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed.
Halex 90512 Twin Screw Clamp Connector Halex 91332 Reducing Conduit Bushing Halex 64005 Conduit Coupling
Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 26071 Knock Out Seals Halex 27511 Hit Lock Cable Connectors Halex 97526 Insulated Conduit Bushing
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 90702 Conduit Chase Nipple Halex 90513 Twin Screw Clamp Connector Halex 20511 Twin Screw Clamp Connector
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Fits non metallic cable number 14/2 to number 6/3 AWG or number 3/10/3 AWG or flex cord .450 to .730 inches diameter. With a 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements.
Halex 96401 Conduit Coupling Halex 16407B Box Spacer Duracell MN27BPK Alkaline Battery
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed. Used mainly for security applications such as car remotes.
Halex 96196 Rigid IMC Conduit Locknut Halex 90514 Twin Screw Clamp Connector Halex 75225 Insulated Conduit Bushing
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Fits non metallic cable number 6/3 to number 2/3 AWG flex cord .800 to 1.350 inches diameter or SE cable 3 conductor or 3 number 1/0 minimum; 3 conductor or 3 number 2/0 maximum. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Eveready 1250 Non-Rechargeable Electronic Battery Halex 01925B IMC Conduit Locknut Halex 96402 Conduit Coupling
Carbon-Zinc. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Bulk packed. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 90661 Standard Water-Tight Connector Halex 90703 Conduit Chase Nipple Eveready 1222 Non-Rechargeable Super Battery
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Carbon Zinc, metal jacket, 25 mA continuous drain at rated capacity. Operating temperature 20 to 130 degrees F. Carded.
Halex 75230 Insulated Conduit Bushing Halex 90662 Standard Water-Tight Connector Halex 64010 Conduit Coupling
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 26073 Knock Out Seals Duracell DL2450BPK Coin Cell Battery Halex 27519 Hit Lock Cable Connectors
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Primary usage is for keyless entry. Lasts longer than alkaline. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified.
Halex 07012 Conduit Chase Nipple Halex 64405 Conduit Elbow LOCK NUT SEALER 1/2IN
LOCK NUT SEALER 1/2IN
Our Price: $3.36
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side.
Halex 26074 Knock Out Seals Halex 05115 Twin Screw Clamp Connector Halex 64012 Conduit Coupling
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Fits non metallic cable, flex cords, multi flex cords; fitting range .834 - 1.520 inches diameter SE cables 2 conductor 4/0. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
WASHER REDUCING 2X1IN         WASHER REDUCING 2X1-1/4IN     Halex 07310 Compression Standard Water-Tight Connector
WASHER REDUCING 2X1IN
Our Price: $3.60
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Halex 94105 Pull Conduit Elbow with Neoprene Gasket Halex 26075 Knock Out Seals Halex 26512 2-Piece Butterfly Clamp Connector
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required.
Halex 58305 Rigid Threaded Conduit Body with Cover and Gasket Halex 58405 Rigid Threaded Conduit Body with Cover and Gasket Halex 58605 Rigid Threaded Conduit Body with Cover and Gasket
Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved.
Halex 58905 Rigid Threaded Conduit Body with Cover and Gasket Halex 64505 Conduit Elbow Halex 64507 Conduit Elbow
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. To connect EMT conduit together to allow for 45 degree bends. To connect EMT conduit together to allow for 45 degree bends.
Halex 58005 Standard Weatherhead Service Entrance Cap Halex 07015 Conduit Chase Nipple Halex 61820B IMC Sealer Locknut
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side.
Energizer A23 Miniature Alkaline Battery Halex 59505 Service Entrance Elbow Coppertop MN1300B2Z Non-Rechargeable Alkaline Battery
Designed for electronic applications which may require high rate pulses such as remotes and cameras. Cell is eight No. LR932 batteries in series in a battery stack. 65 mAH. Carded. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates.
Coppertop MN1604B1Z Alkaline Battery Carlon E995GR Meter Offset Eveready Gold A522 Alkaline Battery
High energy density, capable of performance at high discharge rates. For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. Rated capacity at 25 mA continuous drain. 0 to 130 degrees F operating temperature. Up to 80 percent capacity remaining after 5 years of storage. 565 MAH.
Energizer E95 Alkaline Battery Halex 58007 Clamp On Weatherhead Service Entrance Cap Duracell DL1/3NBBPK Lithium Battery
Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Lasts longer than alkaline in electronic devices.
Halex 05120 Twin Screw Clamp Connector Carlon E998E-CAR Service Entrance Cap Halex 04010 Offset Nipple
Fits non metallic cable, flex cords, multi flex cords fitting range 1.085 - 1.520 inches diameter. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Carlon E995J-CTN Meter Offset Halex 20510 Twin Screw Clamp Connector Halex 64407 Conduit Elbow
For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Halex 64015 Conduit Coupling Halex 58805 Rigid Threaded Conduit Body with Cover and Gasket Halex 94107 Pull Conduit Elbow
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Halex 21642 Box Spacer Halex 60416 Light Duty Wire Holder Energizer E90 Specialty Alkaline Battery
Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box. Plastic label jacket. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. 1,000 mAH. Carded.
Halex 20512 Twin Screw Clamp Connector Halex 64105 Conduit Elbow Eveready Gold A95BP-2 Alkaline Battery
Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Halex 26076 Knock Out Seals Carlon E998F-CAR Standard Weatherhead Service Entrance Cap Energizer 522 Alkaline Battery
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Metal jacket. Up to 80 percent capacity remaining after 5 years of storage. 9 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. 625 MAH. Carded.
Zero-Mercury A544BPZ Miniature Alkaline Battery Halex 08212B Compression Standard Water-Tight Connector Halex 64320 Conduit Nipple
Size replaces 544, PX28A, 4LR44 and V4034PX. 6 volt,  150 mAh. Cell is four No. A76 batteries in series with a metal jacket. 150 mAH. Carded. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed.
Carlon E998G-CAR Service Entrance Cap Halex 95212B Insulated Metallic Grounding Conduit Bushing with Lug Halex 58907 Rigid Threaded Conduit Body with Cover and Gasket
Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 04012 Offset Nipple Halex 58607 Rigid Threaded Conduit Body with Cover and Gasket Toolbasix JL-SST-401183L Cable Crimper
Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Cuts and strip wires, crimps ignition terminals. Easy-to-read wire size markings.
Halex 58307 Rigid Threaded Conduit Body with Cover and Gasket Halex 58407 Rigid Threaded Conduit Body with Cover and Gasket Halex 07020 Conduit Chase Nipple
Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Milwaukee Clipper GS-40 Adjustable Wire Cutter/Stripper Halex 58010 Clamp On Weatherhead Service Entrance Cap Halex 64107 Conduit Elbow
Includes spring return and lock. Adjustable, hardened spring steel. Strips 10-24 gauge wire. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed.
Halex 59507 Service Entrance Elbow Halex 64410 Conduit Elbow Halex 58807 Rigid Threaded Conduit Body with Cover and Gasket
Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed.
BUSHING GRND MTL INSUL 1-1/4IN Gardner Bender GTPS-3100 Cable Stripper Carlon E998H-CAR Standard Weatherhead Service Entrance Cap
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Strips UTP and STP cable up to .24" (6.2mm) OD. Tension release lever, compact design. For use on CAT 3 and CAT 5 cable. Carded. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings.
GB CR-1000 Cable Ripper GE TC100P Rainproof Conduit Hub GE TC125P Rainproof Conduit Hub
GB Cable Ripper, Premium, 14 - 6 AWG Cable/Wire, 4 in Overall Length, cULus Listed, For Use to Cut Off Cable Jacket For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps.
GE TC150P Rainproof Conduit Hub GE TC200P Rainproof Conduit Hub Siemens EC38599 Type RX Conduit Hub
For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps. For use on all Siemans and Murry single position meter sockets.
Siemens EC38597 Type RX Conduit Hub Siemens EC38598 Type RX Conduit Hub Halex 58012 Clamp On Weatherhead Service Entrance Cap
For use on all Siemans and Murry single position meter sockets. For use on all Siemans and Murry single position meter sockets. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed.
Halex 99526 Insulated Metallic Grounding Conduit Bushing with Lug Halex 57499 Oval Standard Service Cable Cap IMC Halex 64020 Conduit Coupling
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Copper-free aluminum die cast. Indoor or outdoor applications. Use in overhead services that utilize SEU cable. Tray boxed. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Energizer EL123AP Lithium Battery Halex 04015 Offset Nipple Energizer EL1CR2 E2 Lithium Battery
Operating temperature -40 to 140 degrees F. Contains a Positive Temperature Coefficient (PTC) safety device to limit current during short circuit conditions. Replaces DL123A. Typical capacity: 1500 mAh (to 2.0 volt). Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Temperature range from -40 to 140 degrees F. Contains a Positive Temperature Coefficient (PTC) safety device to limit current during short circuit conditions. 800 mAH to 2.0 volt.
Halex 58610 Rigid Threaded Conduit Body with Cover and Gasket Halex 60222 Wire Holder Halex 95215B Insulated Metallic Grounding Conduit Bushing with Lug
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Halex 64412 Conduit Elbow Duracell PX28LBPK Lithium Battery Energizer NH15BP-2 Rechargeable Battery
To connect EMT conduit together to allow for 90 degree bends. UL Approved. Lasts longer than alkaline in electronic devices. Plastic label jacket, 1.2 volt. For high drain devices such as digital cameras, CD players, toys and games. High energy, comes charged from the factory, ready to use. Recharges up to 700 times. Carded.
Energizer NH12BP-2 Rechargeable Battery Ultra DLCR2BPK Lithium Battery Halex 95220B Insulated Metallic Grounding Conduit Bushing with Lug
Plastic label jacket, 1.2 volt. For high drain devices such as digital cameras, CD players, toys and games. High energy, comes charged from the factory, ready to use. Recharges up to 700 times. Carded. Lasts longer than alkaline in electronic devices. Light in weight and compact, high energy density, excellent shelf life, long-term reliability, and high rate capability over a broad temperature range. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Coppertop MN1300R4Z Alkaline Battery Coppertop MN1604B2Z Alkaline Battery Siemens ECHS125 Type HS Conduit Hub
Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. High energy density, capable of performance at high discharge rates. For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225.
LOCK NUT SEALER 2IN           Siemens ECHS150 Type HS Conduit Hub Energizer E95BP-4 Non-Rechargeable Alkaline Battery
LOCK NUT SEALER 2IN
Our Price: $8.40
Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Energizer 522BP-2 Alkaline Battery Eveready Gold A522BP Alkaline Battery HUB METER SKT TYPE RX 2-1/2IN
Metal jacket. Up to 80 percent capacity remaining after 5 years of storage. 9 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. 625 MAH. Carded. Rated capacity at 25 mA continuous drain. 0 to 130 degrees F operating temperature. Up to 80 percent capacity remaining after 5 years of storage. 565 MAH. For use on all Siemans and Murry single position meter sockets.
Gardner Bender GS-366 Cable Crimper/Stripper Halex 59510 Service Entrance Elbow Eaton DS125H1P Rainproof Conduit Hub
Strips cable, 10-22 AWG wire, crimps terminals and cuts bolts. Easy-to-read wire size markings. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. For use with MLO and MCB loadcenters and circuit breaker enclosures.
Eaton DS150H1P Rainproof Conduit Hub Halex 64110 Conduit Elbow Eaton ARP00004CH12 Type A Hub Closure Plate
For use with MLO and MCB loadcenters and circuit breaker enclosures. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. For use on Cutler Hammer meter sockets.
Eaton ARP00005CH15 Type A Hub Closure Plate Halex 58015 Clamp On Weatherhead Service Entrance Cap Halex 29523 Insulated Metallic Grounding Conduit Bushing with Lug
For use on Cutler Hammer meter sockets. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Duracell 66158 Rechargeable Battery Duracell 66153 Rechargeable Battery Halex 94110 Pull Conduit Elbow with Neoprene Gasket
Precharged, staycharged, rechargeable batteries. Rechargeable up to 400 times. Precharged, staycharged, rechargeable batteries. Rechargeable up to 400 times. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Eaton DS900AP Rainproof Type DS Hub Adapter Kit Carlon E998J-CAR Service Entrance Cap Energizer LA522 Advanced Lithium Battery
Small hub to large opening. Permits installation of group 1 hubs on 200 Amp type general-duty, heavy-duty and double throw switches. NEMA 3R. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Longer service and lighter, especially in moderate to heavy drain applications. Higher operating voltage and flatter discharge curve with good leakage resistance. No added mercury, cadmium, or lead. Plastic label, miniature snap terminal. 10 year shelf life. 49 mm height x 26.5 mm length x 17.5 mm width.
Halex 09215 Compression Standard Water-Tight Connector Gardner Bender GS-385 Multi-Function Long Nose Plier Halex 10220 Standard Water-Tight Connector
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Multi-function long nose pliers cut, strip and crimp. Use needle nose to form wire or grip small parts. Strips number 14 - number 16 AWG solid or stranded wire. Crimps insulated terminals up to number 10 AWG. Cuts solid or stranded wire. Serrated jaw and cushioned grips. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Mintcraft CP-C8153L Multi Function Wire Stripper Halex 58810 Rigid Threaded Conduit Body with Cover and Gasket Eveready Gold A95BP-4 Alkaline Battery
Rust-resistant steel with cushioned vinyl grip. Easy-to-read wire size markings. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Halex 77920 Service Entrance Cap Eaton ARP00006CH2 Type A Hub Closure Plate Gardner Bender GS-45 Adjustable Wire Cutter/Stripper
Indoor or outdoor applications. Use in an overhead service entrance. Cap mounts on top of PVC, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. Bulk packed. For use on Cutler Hammer meter sockets. Strips solid or stranded wire. Compact, adjusts to eight wire sizes. Hardened spring steel. Looping hole bends, loops wire for termination on screws. Also includes spring return for easy handling.
Eaton RH150P Rainproof Type H Conduit Hub Halex 64415 Conduit Elbow Gardner Bender TT-10B Electrician 3-In-1 Tapping and Rethreading Tool
For load centers No. PL0724R and Challenger No, S3100RN; commonly used on WNB breakers. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Top grade Rockwell 60 steel. Fits tap sizes 6-32, 8-32 and 10-24. Unclogs screw holes, retaps stripped holes.
Halex 59512 Service Entrance Elbow Halex 60525 Adjustable Wire Holder Siemens ECHS200 Type HS Conduit Hub
Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. Porcelain and steel. Used to secure the incoming service entrance wires. Mounts below the overhead service entrance cap. Tray boxed. For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225.
Halex 04020 Offset Nipple Halex 64025 Conduit Coupling Energizer NH22 Rechargeable Battery
Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. NiMH leading-edge technology for high-drain devices - digital cameras, personal digital assistant (PDAs), hand-held games, portable CD players and palmtop computers. Recharges up to 1,000 times. Carded.
Energizer NH35 Rechargeable Battery Energizer NH50 Rechargeable Battery Ultra DL123AB2PK Lithium Battery
NiMH round cell batteries' leading-edge technology makes them ideal for the most advanced, high-drain devices - digital cameras, personal digital assistant (PDAs), hand-held games, portable CD players and palmtop computers. Recharges up to 1,000 times. Batteries use universal charger CHM4FC/CHFCV, Orgill SKU 603.5752. Carded. NiMH round cell batteries' leading-edge technology makes them ideal for the most advanced, high-drain devices - digital cameras, personal digital assistant (PDAs), hand-held games, portable CD players and palmtop computers. Recharges up to 1,000 times. Batteries use universal charger CHM4FC/CHFCV, Orgill SKU 603.5752. Carded. Designed for photo use, such as in digital cameras. Light in weight and compact, high energy density, excellent shelf life, long-term reliability, and high rate capability over a broad temperature range.
SNAKE MINI CABLE 15FT         TOOL CRIMPING COAX            Eaton DS200H2P Rainproof Conduit Hub
SNAKE MINI CABLE 15FT
Our Price: $11.79
TOOL CRIMPING COAX
Our Price: $11.80
Innovative, ultra-compact fish tape. Feed under carpets, over drop ceilings and down walls. Ideal for short runs, installing speakers, home networks, cable and other common electrical uses. Durable, high-impact housing resists breaking. Low memory tape does not curl during extension; ideal for non-conduit situations. Compact, rugged design can be stored in tool box or belt. Weighs 0.5 lbs. Coax crimping tool attaches connectors to F-type RG6 and RG59 coaxial cable. For use with MLO and MCB loadcenters and circuit breaker enclosures.
Gardner Bender GS-389 Cable Cutter/Crimper Gardner Bender GS-89 Cable Cutter/Crimper Halex 10420B Compression Standard Water-Tight Connector
For high-leverage. Cuts up to 3/8" diameter cable. Crimps RG-58, RG-59 and RG-6 F-style connecters. Cushioned grips. For high-leverage. Cuts up to 3/8" diameter cable. Crimps RG-58, RG-59 and RG-6 F-style connecters. Cushioned grips. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
CONNECTOR WATER TITE 2IN      Calterm 66212 Streamline Wire Stripper Halex 64112 Conduit Elbow
CONNECTOR WATER TITE 2IN
Our Price: $12.16
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Cushion grip wire handles. Strips and cuts. Plier nose for pulling and looping wire. Spring return and safety lock. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed.
Energizer EL123AP Cylindrical Lithium Battery Gardner Bender GS-355 Wire Stripper Halex 58020 Clamp On Weatherhead Service Entrance Cap
Operating temperature -40 to 140 degrees F. Contains a Positive Temperature Coefficient (PTC) safety device to limit current during short circuit conditions. Replaces DL123A. Typical capacity: 1500 mAh (to 2.0 volt). Strips solid or stranded wire 10 - 20 AWG. Precision stripping stations. Laser-etched markings. Pliers nose and curved cutting blade aid in pulling and cutting wire. Spring-loaded action returns handles to open position. Curved high-leverage handles for added comfort. Looping hole forms wire to fit on screw terminal. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed.
Square D B150 Rainproof Bolt On Type B Conduit Hub Square D B100 Rainproof Bolt On Type B Conduit Hub Square D B125 Rainproof Bolt On Type B Conduit Hub
Aluminum, for use on NEMA 3R (outdoor) enclosures. Off-center conduit threaded opening and elongated mounting holes reduce the need for conduit offsets and bends while allowing for adjustments. Type B size and is UL and CSA safety listed. Aluminum, for use on NEMA 3R (outdoor) enclosures. Off-center conduit threaded opening and elongated mounting holes reduce the need for conduit offsets and bends while allowing for adjustments. Type B size and is UL and CSA safety listed. Aluminum, for use on NEMA 3R (outdoor) enclosures. Off-center conduit threaded opening and elongated mounting holes reduce the need for conduit offsets and bends while allowing for adjustments. Type B size and is UL and CSA safety listed.
Gardner Bender GS-360 Wire Stripper with Lock Halex 58612 Rigid Threaded Conduit Body with Cover and Gasket Gardner Bender PDTL-3110 Non-Impact Punch Down Tool
Strips solid or stranded wire. Laser-etched markings. Pliers nose and curved cutting blade aid in pulling and cutting wire. Power spring return reduces hand fatigue. Looping hole forms wire to fit on screw terminal.  Wire gauge #10 - #20 AWG. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Non-impact punch-down, non-cut 110-style blade used in CAT 3 and CAT 5 terminations.
Klein Tools 11045 Wire Cutter/Stripper Eaton RH200P Rainproof Type H Conduit Hub Square D B200 Rainproof Bolt On Type B Conduit Hub
Wire gauge markings on both sides, cuts, strips, and loops wire. Wide handles with cushion ridges designed for comfort. Spring-loaded action returns handles to open position. Narrow nose fits into tight places. Made of hardened steel with precision-ground stripping holes. Black oxide finish. No. 11045 strips solid wire AWG. No. 11046 strips stranded wire. For load centers No. PL0724R and Challenger No, S3100RN; commonly used on WNB breakers. Aluminum, for use on NEMA 3R (outdoor) enclosures. Off-center conduit threaded opening and elongated mounting holes reduce the need for conduit offsets and bends while allowing for adjustments. Type B size and is UL and CSA safety listed.
Energizer EL223 Lithium Battery Energizer EL2CR5 Lithium Battery