Home > PLUMBING > KITCHEN & BATH > FIXTURES > LAVATORIES
Sort By:
1
Halex 97521 Insulated Conduit Bushing Halex 97522 Insulated Conduit Bushing Halex 97525 Insulated Conduit Bushing
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 96191 Rigid IMC Conduit Locknut Halex 97523 Insulated Conduit Bushing Halex 96071 Knock Out Seals
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Carlon A240D-CAR 1-Piece Conduit Coupling Halex 96072 Knock Out Seals Halex 96192 Rigid IMC Conduit Locknut
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 26190 Conduit Locknut Halex 97524 Insulated Conduit Bushing Halex 96193 Rigid Conduit Locknut
Halex Conduit Locknut, 1/2 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 91211 Concrete Tight Set Screw Connector Halex 90701 Conduit Chase Nipple Carlon A243D-CAR 1-Piece Snap-In Conduit Adapter
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
Halex 91221 Concrete Tight Set Screw Coupling Carlon A253E-CAR 1-Piece Snap-In Terminal Adapter Halex 91530 Combination Coupling
Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Zinc die cast. Use to join EMT conduit to non-metallic sheathed cable. #14/2, #12/3 or 2 #14/2. Indoor use only. With UPC. UL Approved.
Halex 90510 Twin Screw Clamp Connector Halex 91321 Reducing Conduit Bushing Carlon A253D-CAR 1-Piece Snap-In Terminal Adapter
Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Halex 96194 Rigid IMC Conduit Locknut Halex 91212 Concrete Tight Set Screw Connector Carlon A240E-CAR 1-Piece Conduit Coupling
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Halex 91641 Box Spacer Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter Halex 91222 Concrete Tight Set Screw Coupling
Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT. Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved.
Halex 96510 2-Piece Butterfly Clamp Connector Halex 96195 Rigid Conduit Locknut Halex 91331 Reducing Conduit Bushing
Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved.
Halex 16405B Box Spacer Halex 12110 Concrete Tight Set Screw Connector Halex 90512 Twin Screw Clamp Connector
Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements.
Halex 91332 Reducing Conduit Bushing Halex 64005 Conduit Coupling Halex 26071 Knock Out Seals
Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Halex 27511 Hit Lock Cable Connectors Halex 97526 Insulated Conduit Bushing Halex 12210B Concrete Tight Set Screw Coupling
Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved.
Halex 90702 Conduit Chase Nipple Halex 90513 Twin Screw Clamp Connector Halex 20511 Twin Screw Clamp Connector
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Fits non metallic cable number 14/2 to number 6/3 AWG or number 3/10/3 AWG or flex cord .450 to .730 inches diameter. With a 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements.
Halex 96401 Conduit Coupling Halex 03705B Concrete Tight Set Screw Conduit Offset Halex 90371 Concrete Tight Set Screw Conduit Offset
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Zinc die cast. Use to connect EMT conduit to a metal outlet box or enclosure where an offset is desired. UL Approved. Zinc die cast. Use to connect EMT conduit to a metal outlet box or enclosure where an offset is desired. UL Approved.
Halex 16407B Box Spacer Halex 96196 Rigid IMC Conduit Locknut Halex 90514 Twin Screw Clamp Connector
Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Fits non metallic cable number 6/3 to number 2/3 AWG flex cord .800 to 1.350 inches diameter or SE cable 3 conductor or 3 number 1/0 minimum; 3 conductor or 3 number 2/0 maximum. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements.
Halex 75225 Insulated Conduit Bushing Halex 01925B IMC Conduit Locknut Halex 96402 Conduit Coupling
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Bulk packed. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 90661 Standard Water-Tight Connector Eveready 1235 Non-Rechargeable Super Battery Halex 12112 Concrete Tight Set Screw Connector
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Carbon-Zinc. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved.
Halex 21210 Concrete Tight Set Screw Connector Halex 90703 Conduit Chase Nipple Halex 03707B Concrete Tight Set Screw Conduit Offset
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Zinc die cast. Use to connect EMT conduit to a metal outlet box or enclosure where an offset is desired. UL Approved.
Halex 12212 Concrete Tight Set Screw Coupling Zero-Mercury A76 Miniature Alkaline Battery Halex 75230 Insulated Conduit Bushing
Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved. Designed for electronic applications which may require high rate pulses. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell LR44, Energizer A76, Panasonic L44, Panasonic LR44, Rayovac 867, Rayovac RW51, and Varta V13GA. 11.6mm diameter x 5.4mm height. 150 MAH to .9 volt. 1.5 volt, carded. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 90662 Standard Water-Tight Connector Halex 64010 Conduit Coupling Energizer E91BP-2 Non-Rechargeable Alkaline Battery
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Halex 90372 Concrete Tight Set Screw Conduit Offset Halex 26073 Knock Out Seals Halex 27519 Hit Lock Cable Connectors
Zinc die cast. Use to connect EMT conduit to a metal outlet box or enclosure where an offset is desired. UL Approved. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified.
Quantum 66215 Alkaline Battery Eveready 1215 Non-Rechargeable Super Battery Halex 07012 Conduit Chase Nipple
Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex 64405 Conduit Elbow Halex 12215 Concrete Tight Set Screw Coupling Halex 14405 Pull Conduit Elbow
To connect EMT conduit together to allow for 90 degree bends. UL Approved. Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved. Zinc die cast. Removable steel cover facilitates wire pulling. Use to connect EMT conduit together at a 90 degree bend. Tray box.
LOCK NUT SEALER 1/2IN         Halex 26074 Knock Out Seals Halex 05115 Twin Screw Clamp Connector
LOCK NUT SEALER 1/2IN
Our Price: $3.36
Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Fits non metallic cable, flex cords, multi flex cords; fitting range .834 - 1.520 inches diameter SE cables 2 conductor 4/0. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed.
Halex 12115 Concrete Tight Set Screw Connector Halex 64012 Conduit Coupling Halex 07310 Compression Standard Water-Tight Connector
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Halex 94105 Pull Conduit Elbow with Neoprene Gasket Halex 21212 Concrete Tight Set Screw Connector Halex 26075 Knock Out Seals
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Energizer ECR1616BP Coin Cell Battery Halex 26512 2-Piece Butterfly Clamp Connector Halex 58305 Rigid Threaded Conduit Body with Cover and Gasket
Replaces all 1616 batteries. 16.0mm diameter x 1.6mm height. Lithium / Manganese Dioxide (Li/MnO2). 55 mAh (to 2.0 volts). Carded. UL Listed: MH12454. Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required. Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 58405 Rigid Threaded Conduit Body with Cover and Gasket Halex 58605 Rigid Threaded Conduit Body with Cover and Gasket Halex 12120 Concrete Tight Set Screw Connector
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved.
Halex 58905 Rigid Threaded Conduit Body with Cover and Gasket Halex 64505 Conduit Elbow Coppertop MN1500B4Z Non-Rechargeable Alkaline Battery
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. To connect EMT conduit together to allow for 45 degree bends. High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F.
Halex 64507 Conduit Elbow Eveready Gold A91BP-4 Alkaline Battery Halex 14407 Pull Conduit Elbow
To connect EMT conduit together to allow for 45 degree bends. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Zinc die cast. Removable steel cover facilitates wire pulling. Use to connect EMT conduit together at a 90 degree bend. Tray box.
Halex 58005 Standard Weatherhead Service Entrance Cap Halex 07015 Conduit Chase Nipple Halex 61820B IMC Sealer Locknut
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side.
Halex 12220 Concrete Tight Set Screw Coupling Halex 59505 Service Entrance Elbow Coppertop MN1400B2Z High Capacity Alkaline Battery
Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates.
Carlon E995GR Meter Offset Eveready Gold A93BP-2 Alkaline Battery Energizer E93 Alkaline Battery
For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Energizer E91BP-4 Non-Rechargeable Alkaline Battery Energizer L91BP-2 Non-Rechargeable Cylindrical Lithium Battery Halex 58007 Clamp On Weatherhead Service Entrance Cap
Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Shelf life of 15 years at 21 degrees C (90 percent of rated capacity). UL Listed: MH29980. Typical capacity: 3000 mAh (to 1.0 volt). Carded. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed.
Halex 05120 Twin Screw Clamp Connector Carlon E998E-CAR Service Entrance Cap Halex 04010 Offset Nipple
Fits non metallic cable, flex cords, multi flex cords fitting range 1.085 - 1.520 inches diameter. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Carlon E995J-CTN Meter Offset Halex 20510 Twin Screw Clamp Connector Halex 64407 Conduit Elbow
For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Halex 64015 Conduit Coupling Halex 58805 Rigid Threaded Conduit Body with Cover and Gasket Halex 94107 Pull Conduit Elbow
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Halex 21642 Box Spacer Halex 21222 Concrete Tight Set Screw Coupling Halex 60416 Light Duty Wire Holder
Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved. Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box.
Halex 20512 Twin Screw Clamp Connector Halex 64105 Conduit Elbow Energizer 1209 Super Lantern Battery
Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Carbon-Zinc battery. Plastic jacket. Coil spring terminal. 6 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 degrees F to 130 degrees F. Lower unit weight than alkaline. 11 AH to 0.8 volt.
Halex 14605 Inside Corner Pull Conduit Elbow Halex 26076 Knock Out Seals Halex 21211 Concrete Tight Set Screw Connector
Zinc die-cast. Removable steel cover facilitates wire pulling. Use to connect EMT conduit together at an inside corner. UL listed, CSA Approved. Tray boxed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved.
Carlon E998F-CAR Standard Weatherhead Service Entrance Cap Halex 08212B Compression Standard Water-Tight Connector Halex 64320 Conduit Nipple
Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed.
Energizer ECR1632BP Coin Cell Battery Quantum 66217 Alkaline Battery Energizer 2032BP-2 Coin Cell Battery
For electronics around the house, like keyless entry, electronic books and glucose monitors. Performs in extreme temperatures from -22 to 140 degrees F. Holds power for 8 years when not in use. Replacement for: BR1632, DL1632, ECR1632, KCR1632, KECR1632, KL1632, L1632. UL Listed. Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Replaces Duracell DL2032, Energizer ECR2032, Panasonic CR2032, and Rayovac CR2032. 20.0mm diameter x 3.2mm height. Lithium / Manganese Dioxide (Li/MnO2). 240 mAh (to 2.0 volts). Carded. UL Listed: MH12454.
Energizer 2016BP-2 Button Cell Battery Halex 21221 Concrete Tight Set Screw Coupling Carlon E998G-CAR Service Entrance Cap
Replaces Energizer ECR2016. .08" diameter x .008" height. Lithium / Manganese Dioxide (Li/MnO2), 90 mAh (to 2.0 volts) typical capacity, 1.9 grams (0.07 oz.) typical weight. Carded. UL Listed: MH12454. Zinc die cast. Use to join two lengths of EMT conduit together. UL Approved. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings.
Halex 95212B Insulated Metallic Grounding Conduit Bushing with Lug Halex 58907 Rigid Threaded Conduit Body with Cover and Gasket Halex 04012 Offset Nipple
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved.
Halex 58607 Rigid Threaded Conduit Body with Cover and Gasket Zero-Mercury 357BPZ-3 Non-Rechargeable Electronic Coin Cell Battery Energizer 2025BP-2 Coin Cell Battery
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell D357/303, Goldpeak 357, Kodak L1154, Maxell SR44W, Panasonic SP357, Rayovac 357, Renata 357, Sony SR44W, Toshiba SR44W, and Varta V357. 11.6mm diameter x 5.4mm height. 150 MAH to 1.3 volt. Replaces Duracell DL2025 and Rayovac CR2025. 20.0mm diameter x 2.5mm height. Lithium / Manganese Dioxide (Li/MnO2). 170 mAh to 2.0 volt. Carded. UL Listed: MH12454.
Halex 58307 Rigid Threaded Conduit Body with Cover and Gasket Halex 58407 Rigid Threaded Conduit Body with Cover and Gasket Halex 07020 Conduit Chase Nipple
Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex 58010 Clamp On Weatherhead Service Entrance Cap Halex 64107 Conduit Elbow Halex 59507 Service Entrance Elbow
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed.
Halex 64410 Conduit Elbow Halex 58807 Rigid Threaded Conduit Body with Cover and Gasket BUSHING GRND MTL INSUL 1-1/4IN
To connect EMT conduit together to allow for 90 degree bends. UL Approved. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Halex 14607 Inside Corner Pull Conduit Elbow Carlon E998H-CAR Standard Weatherhead Service Entrance Cap GE TC100P Rainproof Conduit Hub
Zinc die-cast. Removable steel cover facilitates wire pulling. Use to connect EMT conduit together at an inside corner. UL listed, CSA Approved. Tray boxed. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. For outdoor enclosures with removable closing caps.
GE TC125P Rainproof Conduit Hub GE TC150P Rainproof Conduit Hub GE TC200P Rainproof Conduit Hub
For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps.
Siemens EC38599 Type RX Conduit Hub Siemens EC38597 Type RX Conduit Hub Siemens EC38598 Type RX Conduit Hub
For use on all Siemans and Murry single position meter sockets. For use on all Siemans and Murry single position meter sockets. For use on all Siemans and Murry single position meter sockets.
Halex 58012 Clamp On Weatherhead Service Entrance Cap Halex 99526 Insulated Metallic Grounding Conduit Bushing with Lug Powerzone LR6-16P Alkaline Battery
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Mercury and cadmium free.
Halex 57499 Oval Standard Service Cable Cap IMC Powerzone OR802013 Surge Protector Strip Halex 64020 Conduit Coupling
Copper-free aluminum die cast. Indoor or outdoor applications. Use in overhead services that utilize SEU cable. Tray boxed. Household use surge protector. Straight plug. Full, 3-line protection against surges through hot, neutral or ground lines, built-in circuit breaker switches to protect against overloads. Superior joule ratings and clamping voltage ratings. Rated 400 joule, 15 amp, 125 volt, 1875 watts. UL listed. Carded. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Coppertop MN15B8ZTSS Alkaline Battery Halex 04015 Offset Nipple Halex 58610 Rigid Threaded Conduit Body with Cover and Gasket
High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved.
Halex 60222 Wire Holder Halex 58705 EMT Set Screw Conduit Body with Cover and Gasket Halex 95215B Insulated Metallic Grounding Conduit Bushing with Lug
Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved.
Halex 64412 Conduit Elbow SURGE APPL 1080J 1-OUTLET GRY Energizer E91MP-8 Non-Rechargeable Alkaline Battery
To connect EMT conduit together to allow for 90 degree bends. UL Approved. Protects appliances from power surges. When the unit is no longer protecting, it will sound an alarm. 1080 Joules, 15 Amp/120 VAC. 60 Hz, 1800 watts. Max surge: 6000V, max spike: 45000A, response: <1ns. LED indicator, overload protection. Indoor use only. Tri-lingual package, (English/French/Spanish). cULus Listed. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Halex 95220B Insulated Metallic Grounding Conduit Bushing with Lug Coppertop MN1400R4ZX Alkaline Battery Eveready Gold A91BP-8 Alkaline Battery
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Siemens ECHS125 Type HS Conduit Hub LOCK NUT SEALER 2IN           TAP SURGE 5-OUT 900J WHT/GRAY
LOCK NUT SEALER 2IN
Our Price: $8.40
For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Tap surge 5-outlets, protected and grounded indicator lights, 2 wide-spaced outlets for transformer plug.
Siemens ECHS150 Type HS Conduit Hub Energizer L91BP-4 Non-Rechargeable Cylindrical Lithium Battery Energizer E93BP-4 Alkaline Battery
For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225. Shelf life of 15 years at 21 degrees C (90 percent of rated capacity). UL Listed: MH29980. Typical capacity: 3000 mAh (to 1.0 volt). Carded. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
HUB METER SKT TYPE RX 2-1/2IN Halex 59510 Service Entrance Elbow Eaton DS125H1P Rainproof Conduit Hub
For use on all Siemans and Murry single position meter sockets. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. For use with MLO and MCB loadcenters and circuit breaker enclosures.
Eaton DS150H1P Rainproof Conduit Hub Eveready Gold A93BP-4 Alkaline Battery Powerzone OR802105 Surge Protector Tap
For use with MLO and MCB loadcenters and circuit breaker enclosures. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Single outlet, 900 joule surge tap, white. Rated 15 amp, 125 volt and 1875 watts. Built-in circuit breaker to protect against overloads. Protected and grounded indicator lights.
Halex 64110 Conduit Elbow Eaton ARP00004CH12 Type A Hub Closure Plate Eaton ARP00005CH15 Type A Hub Closure Plate
Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. For use on Cutler Hammer meter sockets. For use on Cutler Hammer meter sockets.
Halex 58015 Clamp On Weatherhead Service Entrance Cap Halex 29523 Insulated Metallic Grounding Conduit Bushing with Lug Mintcraft OR802124 Surge Protector
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Straight plug. Outlet safety covers. 3 foot power cord. 15A/125V/1875W.
Halex 94110 Pull Conduit Elbow with Neoprene Gasket Eaton DS900AP Rainproof Type DS Hub Adapter Kit Carlon E998J-CAR Service Entrance Cap
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. Small hub to large opening. Permits installation of group 1 hubs on 200 Amp type general-duty, heavy-duty and double throw switches. NEMA 3R. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings.
Halex 09215 Compression Standard Water-Tight Connector Powerzone LR6-24P Alkaline Battery Halex 10220 Standard Water-Tight Connector
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Mercury and cadmium free. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub.
Halex 58810 Rigid Threaded Conduit Body with Cover and Gasket Halex 77920 Service Entrance Cap Eaton ARP00006CH2 Type A Hub Closure Plate
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Indoor or outdoor applications. Use in an overhead service entrance. Cap mounts on top of PVC, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. Bulk packed. For use on Cutler Hammer meter sockets.
Quantum 66225 Alkaline Battery SURGE ELECTRNCS 1000J 3OUT GRY Eaton RH150P Rainproof Type H Conduit Hub
Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Phone cradle, safety covers, wire wrap and easy pull design. 1000 Joules, 15 Amp/120 VAC. 60 Hz, 1800 watts. Max surge: 6000V, Max spike: 30,000A, response: <1ns. Overload protection. Indoor use only. Tri-lingual package, (English/French/Spanish). cULus Listed. For load centers No. PL0724R and Challenger No, S3100RN; commonly used on WNB breakers.
TAP 1-OUT 150J 1-PORT 2.4A USB Halex 64415 Conduit Elbow Halex 59512 Service Entrance Elbow
USB charger, folding plug, Compact design perfect for travel. 20-percent faster USB charging. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed.
Zenith AS110024C Speaker Wire Halex 60525 Adjustable Wire Holder Coppertop MN15RT12Z Reclosable Alkaline Battery
Used for stereos and hi-fi systems, home theater sound systems. Connects speaker to receiver, tuner/amplifier. Porcelain and steel. Used to secure the incoming service entrance wires. Mounts below the overhead service entrance cap. Tray boxed. High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F.
Energizer CHVCWB2 Value Plug-In Battery Charger Duracell MN908 Non-Rechargeable Lantern Alkaline Battery Siemens ECHS200 Type HS Conduit Hub
Charges 2 or 4 AA and/or AAA NiMH batteries at a time. Two green LEDs indicate when batteries are charging. Reverse polarity protection prevents damage from incorrectly installed batteries. Charges NiMH batteries in 8 to 16 hours, depending on type and number. Batteries must be charged in pairs. No shutoff mechanism, typical weight 5.9 oz. Fold-out plug. 120 volt, 60 Hz. 57 mm width x 70 mm length x 132 mm height. Provides power and long life. For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225.
Halex 04020 Offset Nipple Halex 64025 Conduit Coupling SNAKE MINI CABLE 15FT
SNAKE MINI CABLE 15FT
Our Price: $11.79
Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Innovative, ultra-compact fish tape. Feed under carpets, over drop ceilings and down walls. Ideal for short runs, installing speakers, home networks, cable and other common electrical uses. Durable, high-impact housing resists breaking. Low memory tape does not curl during extension; ideal for non-conduit situations. Compact, rugged design can be stored in tool box or belt. Weighs 0.5 lbs.
Zenith AS105018C Speaker Wire CHARGER USB 3.4A 2-OUT 450J   Eaton DS200H2P Rainproof Conduit Hub
Used for stereos and hi-fi systems, home theater sound systems. Connects speaker to receiver, tuner/amplifier. Compact design perfect for travel, Red and green charging indicator lights. Slim style surge tap. 20-percent faster charging. For use with MLO and MCB loadcenters and circuit breaker enclosures.
Halex 10420B Compression Standard Water-Tight Connector CONNECTOR WATER TITE 2IN      Energizer 529 Lantern Battery
CONNECTOR WATER TITE 2IN
Our Price: $12.16
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Metal jacket, operating temperature of 0 to 130 degrees F. 26,000 mAH to 0.8 volt.
Halex 64112 Conduit Elbow Halex 21220 Concrete Tight Set Screw Coupling Halex 12207B Concrete Tight Set Screw Coupling