Home > PLUMBING > KITCHEN & BATH > WATER FILTERS > ICEMAKER WATER FILTERS
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Thomas & Betts BH122A-UPC Outlet Box Raco 8977 Electrical Box Supports Carlon B112HB Handy Box
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation.
Hubbell 8660 Utility Box Thomas & Betts B114R-UPC Switch Box Thomas & Betts B232A-UPC Outlet Box
Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4".
Hubbell 8192 Outlet Box Halex 26279 Switch Box Support Thomas & Betts B108B-UPC Outlet Box
Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. Use to suport attachment of an outlet box in drywall, paneling, etc., in the absence of a structure member. Installed in pairs. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed.
Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box Allied Moulded 1098-N Switch Box
Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4". Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box Allied Moulded P241 Switch Box
Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Residential thermoplastic switch or receptacle box. With angled nails. 3-9/16" depth x 2-1/4" width x 3-3/4" height. 24 cubic inch volume. Fire rating classification of 2 hours in wall and ceiling. UL Listed.
Raco 8190 Outlet Box Raco 8189 Ceiling Outlet Box Raco 7887RAC Old Work Cable Box
Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Allied Moulded 1099-N Switch Box Hubbell 8650 Welded Utility Box Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Raco 8196 Electrical Box Hubbell 8670 Welded Utility Box
Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed.
Raco 8197 Welded Electrical Box Thomas & Betts B120R Outlet Box Raco 662 Drawn Utility Box
Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches.
Raco 653 Utility Box Thomas & Betts BH235A Outlet Box Carlon A521DE ENT Flexible Raceway Outlet Box
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed.
Hubbell 665 Utility Box Extension Ring Carlon SC100A 1-Gang Low Voltage Mounting Bracket Hubbell 8663 Utility Box
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Raco 473 Gangable Switch Box Hubbell 8232 Outlet Box Carlon SC200RR Low Voltage Old Work Bracket
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed.
Raco 528 Gangable Switch Box Hubbell 8500 Gangable Switch Box Carlon B418A-UPC Shallow Outlet Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Thomas & Betts B225R-UPC Outlet Box Raco 661 Handy Box Raco 400 Gangable Switch Box
With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16" Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed.
Thomas & Betts B121ADJ Wall Box Thomas & Betts B344AB-UPC Outlet Box Hubbell 519 Gangable Switch Box
Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls.
Hubbell 8531 Gangable Switch Box Raco 404 Non-Gangable Shallow Switch Box Hubbell 471 Gangable Switch Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed.
Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box Allied Moulded 9318 Handy Box
Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed.
Raco 420 Gangable Switch Box Raco 560 Gangable Switch Box Raco 8355 Non-Gangable Switch Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed.
Raco 674 Handy Box Raco 8201 Extension Ring Outlet Box Raco 7488RAC Old Work Cable Box
For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed. For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed. Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity.
Allied Moulded 9363-EWK Old Work Switch Box Raco 920 Steel Bar Hangers Raco 567 Gangable Switch Box
Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Holding prong, box clip holds box in place for nailing. Design resists bending and twisting. With stud. Length 14-1/4" thru 22-1/2". With locking tabs to hold bar in position. UL Listed. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Hubbell 8203 Electrical Box Extension Ring Thomas & Betts B432A-UPC Outlet Box Raco 976 Extension Ring Switch Box
For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code.
Thomas & Betts BH353A Lightweight Outlet Box Thomas & Betts SC200DV Dual Voltage Outlet Box Allied Moulded 9361-ESK Old Work Switch Box
Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed.
Hubbell 518 Gangable Switch Box Thomas & Betts B232B-UPC Outlet Box Raco 223 Electrical Box
One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed.
Carlon Super Blue BH118R Old Work Outlet Box Raco 529 Gangable Switch Box Carlon A122 ENT Flexible Raceway Outlet Box
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth.
Raco 545 Non-Gangable Old Work Switch Box Raco 8211 Outlet Box Allied Moulded 2300-NK Switch Box
Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed.
Raco 508 Non-Gangable Switch Box Hubbell 8257 Welded Outlet Box Raco 487 Gangable Old Work Switch Box
Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed. Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches.
Raco 8601 Gangable Switch Box Raco TigerGrip 523 Gangable Old Work Switch Box Carlon Super Blue BH234R Old Work Outlet Box
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed.
Thomas & Betts B355R Outlet Box Raco 2011FBAR Vapor Barrier Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box
Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings.
Raco 8235 Electrical Box Raco 605 Gangable Switch Box Carlon B455A-UPC Outlet Box
Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed. Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5".
Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box Raco 8265 Ceiling Outlet Box Thomas & Betts B234ADJ Wall Box
Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed. Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C.
Thomas & Betts BH464A Rigid Outlet Box Allied Moulded 9312-EWK Old Work Outlet Box Allied Moulded 3300-NK Outlet Box
Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed. Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed.
Tiger Grip 517 Gangable Switch Box Raco 680 Switch Box Raco 681 Switch Box
Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed. Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B468R Old Work Outlet Box Raco 8240 Electrical Box Raco 685 Switch Box
Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed.
Hubbell 683 Switch Box Raco 2002FBAR Vapor Barrier Box Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box
Drawn construction for surface mount applications. Conduit wiring system. Eight 1/2" and four 3/4" conduit knockouts (sides). Three 1/2" and two 3/4" conduit knockouts (bottom). 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed.
Sliderbox SB Adjustable Switch/Receptacle Outlet Box Raco 509 Old Work Switch Box Allied Moulded 9313-EWK Old Work Switch Box
Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 42 cubic inch volume, two 1/2" knockouts. Internal steel, stud/wood screws. 3-9/16" depth x 4" width x 3-3/4" height. UL listed for 2 hour fire resistive walls. Conduit wiring system. Gangable switch box offers the option of constructing a box to hold two or more devices. Adjustable plaster ears allow box to be used in old work applications. Provided old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Two 1/2" bottom knockouts and two 1/2" end knockouts. 2-1/2" deep - 12.5 cubic inches. UL Listed. Thermoset-fiberglass with ears, wing brackets, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" depth x 5-15/16" x 3-1/4". UL Listed.
Culligan Sales IC-100A Water Filter Icemaker Kit BOX 3GANG 1-5/8DEEP 1/2-3/4 KO Raco 686 Switch Box
Connects to back of refrigerator to provide better tasting water for ice cubes and beverages. Features conventional nylon fittings to attach to plastic or copper tubing, and granular activated carbon to reduce sediment, chlorine, unpleasant tastes and odors. Up to 12-month life depending on usage and water conditions. Used where a number of wiring devices are to be centrally located. Features 1/2" and 3/4" concentric knockouts for use with a wide variety wiring methods. 1-5/8" x 4.5" x 8.63". UL Listed. Welded construction. Conduit wiring system. Two 1/2" and two 3/4" knockouts (sides). Three 1/2" and three 3/4" knockouts (bottom). Six 1/2" and six 3/4" knockouts (end). FM type bracket for wood or metal studs. 2-1/2" deep - 47.8 cubic inches. UL Listed.
Raco 687 Switch Box Carlon SC300PRR Electrical Box Culligan IC-EZ-1 Ez-Change Icemaker/Refrigerator Dispensers
Conduit wiring system. Welded construction. FM bracket for wood or metal studs. Eight conduit knockouts (sides). Two conduit knockouts (end).  Four conduit knockouts (bottom). 63.5 cubic inch capacity. 7-19/32" wide x 2-1/2" deep. UL Listed. Nonmetallic ABS material is lightweight, paintable and easy to handle. Recessed low profile design provides ample room behind dry wall and between studs to accommodates cable bend requirements. Hides the wires, cables, cords and plug heads used with flat panel display installations. Has a two gang low voltage opening and a universal one gang opening for an outlet or switch box (boxes, devices, and plates not included). 4 swing out clamps lock the plate securely to the wall, horizontal or vertical mount. 2.72" depth x 5.25" width x 10.5" length. Kit includes filter head with built-in bracket, RC-EZ-1 level 1 replacement filter cartridge, mounting screws, and filter change reminder sticker. Features twist-on, twist off mechanism, and quick-connect fittings - double water shut-off. 3,000 gallon capacity. NSF certified. Reduces bad taste and odor, chlorine taste and odor, and particulate class III.
Toolbasix PF8101A Kitchen Faucet Toolbasix PF8111A Kitchen Faucet Culligan 1000-R Easy Change Water Filter Cartridges
8" centers. Single ABS lever handle, ABS construction, plastic waterways, washerless cartridge, 1/2" 14NPSM inlet, IAMPO & NSF certified. Carded. 8" centers. Single ABS lever handle, ABS construction, plastic waterways, washerless cartridge, 1/2" 14NPSM inlet, IAMPO & NSF certified. Carded. No-hassle, no-mess design for cartridge replacement. Simply twists off and on No.IC-1000 icemaker/water dispenser filter with no tools and virtually no spillage of water to reduce lead, Cryptosporidium, Giardia, Lindane, Atrazine, sediment, chlorine and unpleasant tastes and odors. Up to 6-month/500-gallon life depending on usage and water conditions.
FAUCET KITCHEN 8IN LEVER CHRM Culligan IC-EZ-3 Ez-Change Icemaker/Refrigerator Dispensers FAUCET KITCHEN 8IN LEVER CHRM
Chrome, metal lever handle, durable metal construction, hybrid waterway, stainless steel ball valve, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi. Kit includes filter head with built-in bracket, RC-EZ-3 level 3 replacement filter cartridge, mounting screws, and filter change reminder sticker. Features twist-on, twist-off mechanism, and quick-connect fittings - double water shut-off. 500 gallon capacity. NSF certified. Reduces bad taste and odor, chlorine taste and odor, sediment, lead, cysts such as cryptosporidium and giardia, turbidity, atrazine, lindane, and particulate class I. Chrome, metal lever handle, durable metal construction, hybrid waterway, stainless steel ball valve, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi.
FAUCET KITCHEN 8IN LEVER CHRM Peerless P188200LF Kitchen Faucet Mintcraft 67534-1001 Kitchen Faucets
With white hose spray on deck, chrome, metal lever handle, durable metal construction, hybrid waterway, stainless steel ball valve, 1/2in 14NPSM inlet, 8in centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi. 3-hole sink application, washerless ball valve, spout swivels 360 degrees for added convenience, ADA Compliant, 9" spout length. With matching finish side spray, metal lever handle, durable metal construction, hybrid waterway, ceramic cartridge, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi.
Peerless P188500LF Kitchen Faucet Moen Adler Kitchen Faucet Delta 100-DST Kitchen Faucet
4-hole, 8" sink application,washerless ball valve, spout swivels 360 degrees for added convenience, ADA Compliant. Spout length: 9", Flow Rate: 1.8 gpm @ 60 psi, 6.8 L/min @414 kPa 4" center. 12550 ceramic disc cartridge design. Water/energy saving aerator. Hook-up supplies included. 1/2" IPS inlets. Inlet shanks will accept 3/8" ball nose connections. Third party certified to ASME A112.18.1/CSA B125.1, ICC A117.1 and all applicable requirements referenced therein, certified to ANSI/NSF 61/9. Complies with California Proposition 65 and with the Federal Safe Water Drinking Act. 1.5 gpm. Three hole , 8" installation, 8" swing spout. 1/2" IPS inlets
Moen Adler Kitchen Faucet Moen Adler Kitchen Faucet American Standard Jocelyn Kitchen Faucet
Chrome finish, Duralock quick connect system, complies with ADA specifications. 3-hole, 3/8" compression connection, 1255 Duralast cartridge. 1.5 gpm. 4" center. 12550 ceramic disc cartridge design. Water/energy saving aerator. Hook-up supplies included. 1/2" IPS inlets. Inlet shanks will accept 3/8" ball nose connections. Third party certified to ASME A112.18.1/CSA B125.1, ICC A117.1 and all applicable requirements referenced therein, certified to ANSI/NSF 61/9. Complies with California Proposition 65 and with the Federal Safe Water Drinking Act. 1.5 gpm. Cast brass 8-1/2" swivel spout, washerless 40mm ceramic disc valve cartridge, cast brass waterway with 1/2" male inlet shanks, metal escutcheon plate (10-5/16"H x 2-3/8"W). 1.8 gpm. Lifetime Warranty.
FAUCET KIT PULOUT SNGL LEV CHR Moen Adler Kitchen Faucet Mintcraft 67534-1004 Kitchen Faucet
Metal lever handle, durable metal construction, lead free brass waterway, ceramic cartridge, 1/2in 14NPSM inlet, 8in centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi, pull-out dual sprayer. Lever-style handle. 1/2" IPS connections will accept standard ball nose connection for 3/8" tubing. 9" sprout reach, 4 hole application. Aerator is limited to 1.5 gpm max. 1255 cartridge design, nonmetallic, nonferrous and stainless steel materials. Complies with requirements of CSA B-125, ASME A112.18.1M, ANSI A117.1, and ADA. Certified to ANSI/NSF61/9. Compliant with California Proposition 65 and with the Federal Safe Water Drinking Act. 1/2" IPS connectors. With matching finish side spray, metal lever handle, durable metal construction, hybrid waterway, ceramic cartridge, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi.
Delta Classic Kitchen Faucet Raco 692 Non-Gangable Old Work Switch Box Moen Banbury Kitchen Faucet
8" installation. Diamond seal valve, 2.2gpm at 60psi, 8" long spout swings 360 degrees for added convenience, ADA compliant. Welded construction. Rectangular shape fits square cuts in block. Device ears inside the box, preventing mortar from getting in the device hole. Use a standard wall plate cover. Concentric knockouts, 6 end, 3 bottom and 4 sides. Nongangable. 47.8 cubic inches. 5-19/32" wide x 2-1/2" deep. Used in 4" block walls. UL Listed. Low arc kitchen faucet with side spray, four hole application, one function sprayer, 1/2 IPS connection, 1255 ceramic cartridge, deckplate included Chrome finish. 1.5 gpm.
BOX SW 2-1/2DP TS-BRKT MC-CLMP Delta Classic Kitchen Faucet FAUCET KIT W/PULL DOWN SPRY
One 1/2" bottom and two 1/2" end conduit knockouts and four cable knockouts. With armored cable/metal clad/flex clamps. TS brackets for wood or metal studs, with 1/2" setback. Gauging tabs and recessed nailing spur, less ears. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. 8" installation. Diamond seal valve, 2.2gpm at 60psi, 8" long spout swings 360 degrees for added convenience, ADA compliant. Zinc diecast body with brass swivel spout and metal lever handle, pull-down spray with 4 function spray with pause that offers stream, spray,mist and jetsprays.The metal soap dispenser and deck plate dispenser allow installation on sinks with 1 to 4 faucet holes and the Re-Trax Pulll-Down System allows the spray head to retract completely. adjustable spray pattern and push button activation, metal reinforced hose, washerless 40mm ceramic disc valve cartridge, complete with two integral check valves, braided flexible supply hoses with 3/8" compression connectors.  1.8 gpm.Lifetime Warranty.
American Standard Jocelyn Kitchen Faucet FAUCET KIT PULOUT SNGL LEV NIC FAUCET KTN PULL-DN CNTMPRY CHM
Cast brass 8-1/2" swivel spout, washerless 40mm ceramic disc valve cartridge, cast brass waterway with 1/2" male inlet shanks, metal escutcheon plate (10-5/16"H x 2-3/8"W). 1.8 gpm. Lifetime Warranty. Metal lever handle, durable metal construction, lead free brass waterway, ceramic cartridge, 1/2in 14NPSM inlet, 8in centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi, pull-out dual sprayer.
Moen Lindley Kitchen Faucet Delta 440-DST Collins Kitchen Faucet Peerless P18550LF-SD Pull Out Kitchen Faucet With Soap Dispenser
Chrome finish, side spray, Hydrolock quick connect system, four hole installation, 1/2" IPS connection, 1.5 gpm max, ADA compliant. 8" center, 9" swivel spout with single lever handle. Quick Snap vegetable sprayer hose with matching finish sprayhead. 45" long hose. Requires 4-hole installation. Supplied with universal fittings to accept 3/8" copper sweat, 3/8" compression, includes adapters to accept 1/2" iron pipe. Single lever control for ease of operation with one hand, integrated pull-out sprayer for easy pot filling and clean up, 2 or 4-hole sink applications using optional escutcheon, matching soap dispenser included for added convenience.
FAUCET KITCHEN PULLDOWN CHROME Moen Lindley Kitchen Faucet Moen Muirfield Kitchen Faucet
Metal lever handle, durable metal construction, lead free brass waterway, ceramic cartridge, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi, pull-down dual sprayer, supply lines included. Low arc, chrome finish, Duralock quick connect system for easy installation, complies with American with Disabilities Act specifications. 1255 Duralast cartridge, flexible supply lines with 3/8" compression fittings.1.5 gpm. Low arc faucet with one-function side spray, 4-hole mounting, 1/2" IPS connection, 1255 ceramic cartridge, deckplate included. Classic Chrome finish. 1.5 gpm.
Moen Torrance Kitchen Faucet FAUCET KTN PULL-DN CONTMPRY BN Moen Chateau Kitchen Faucet
Metal construction. Inlet shanks will accept 3/8" ball nose connections. Includes Protege side spray. Lever style handle. Pull-on/push-off. Operates with less than 5 lbs. of force. Aerator is limited to 1.5 gpm max. Third party certified to CSA B125, ASME A112.18.1M, ANSI A117.1 and all applicable requirements referenced therein. Certified to ANSI/NSF 61/9. Complies with California Proposition 65 and with the Federal Safe Water Drinking Act. ADA compliant. One solid lever handle. Energy saving flow-rator, aerator. Includes Protege side spray. ADA compliant.
American Standard McKenzie Pull-Down Kitchen Faucet Moen Renzo Pull-Out Kitchen Faucet Moen Renzo Pull-Out Kitchen Faucet
Zinc diecast body with brass swivel spout and metal lever handle, pull-down spray with adjustable spray pattern and push button activation, metal reinforced hose, washerless 40mm ceramic disc valve cartridge, complete with two integral check valves, braided flexible supply hoses with 3/8" compression connectors. Compatible with 1-hole or 2-hole sinks 1.8 gpm.Lifetime Warranty. Metal construction with Hydrolock quick connect installation. Pullout spray with 68" braided hose. 1/2" IPS connections will accept standard ball nose connection for 3/8" tubing. Lever-style handle. Temperature controlled by 120 degree arc of handle travel. Spout receptor rotation is 120 degrees. Operates with less than 5 Ibs. of force.  Operates in stream or spray mode in the pullout or retracted position. Flow is limited to 1.5 gpm max. Designed to install thru 1 or 3 holes 1-1/4" (32mm) min. Third party certified to CSA B-125, ASME A112.18.1M, NSF 61 Section 9, California Proposition 65, ANSI A117.1 and all applicable requirements referenced therein. ADA compliant. The backflow protection system in this device consists of two independently operating check valves, a primary and a secondary which prevent backflow. Metal construction with Hydrolock quick connect installation. Pullout spray with 68" braided hose. 1/2" IPS connections will accept standard ball nose connection for 3/8" tubing. Lever-style handle. Temperature controlled by 120 degree arc of handle travel. Spout receptor rotation is 120 degrees. Operates with less than 5 Ibs. of force.  Operates in stream or spray mode in the pullout or retracted position. Flow is limited to 1.5 gpm max. Designed to install thru 1 or 3 holes 1-1/4" (32mm) min. Third party certified to CSA B-125, ASME A112.18.1M, NSF 61 Section 9, California Proposition 65, ANSI A117.1 and all applicable requirements referenced therein. ADA compliant. The backflow protection system in this device consists of two independently operating check valves, a primary and a secondary which prevent backflow.
Delta 340-DST Collins Kitchen Faucet Delta Faucet 4453-DST Kitchen Faucet FAUCET KITCHN PULLDWN STAINLES
Single handle kitchen deck faucet for exposed mounting on three hole sinks. Solid brass fabricated body. 9-1/16" long spout swings 360 degrees. Lever handle returns to neutral position when faucet is turned off. Red and blue button on handle. Control mechanism is of rotating stainless steel ball type with replaceable non-metallic seats operating in stainless steel lined sockets. 3/8" O.D. straight, staggered copper supply tubes - 5-7/8" and 7-1/4" long supplied with 1/2"-14 NPSM adapters. Spray attachment has anti-siphon device as integral part of valve body. Includes Quick Snap vegetable sprayer hose with matching finish sprayhead. 45" long hose. Complies with ASME A112.18.1, CSA B125, IAPMO listed, CSA certified, and City of L.A. approved. ADA compliant. Tall arc spout, Diamond Seal valve, 2 or 4-hole 8" installation. 9-13/16" spout. 10-1/2" escutcheon included. Metal lever handle, durable metal construction, lead free brass waterway, ceramic cartridge, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi, pull-down dual sprayer, supply lines included.
FAUCET KTN SPRING PULL-DWN CHM FAUCET PULLDOWN SS W/SOAP DISP Delta 440-SS-DST Collins Kitchen Faucet
Zinc diecast body with brass swivel spout and metal lever handle, pull-down spray with adjustable spray pattern and push button activation, metal reinforced hose, washerless 40mm ceramic disc valve cartridge, complete with two integral check valves, braided flexible supply hoses with 3/8" compression connectors. Compatible with 1-hole, 3-hole or 4 -hole sinks 1.8 gpm.Lifetime Warranty. 4-hole 8" centers, 9-3/16" spout swings 180 degrees, diamond coated ceramic cartridge, 3/8" compression gasket fittings.
FAUCET KIT PULDWN SNGL LEV CHR Moen Wetherly Kitchen Faucet FAUCET KITCHEN PULLDOWN V-BRNZ
Metal lever handle, durable metal construction, lead free brass waterway, ceramic cartridge, 1/2 in 14NPSM inlet, 8 in centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi, pull-down dual sprayer, supply lines included. Side spray, conventional deck mounting, 2 or 4 hole application, 3/8" compression connection, 7.87" spout height, 1.5 gpm. Metal lever handle, durable metal construction, lead free brass waterway, ceramic cartridge, 1/2" 14NPSM inlet, 8" centers, IAMPO and NSF certified, max 1.8 Gpm at 60 psi, pull-down dual sprayer, supply lines included.
FAUCET KTN SPRING PULL-DN BNKL Moen Renzo Pull-Out Kitchen Faucet Moen Wetherly Kitchen Faucet
Metal construction with Hydrolock quick connect installation. Pullout spray with 68" braided hose. 1/2" IPS connections will accept standard ball nose connection for 3/8" tubing. Lever-style handle. Temperature controlled by 120 degree arc of handle travel. Spout receptor rotation is 120 degrees. Operates with less than 5 Ibs. of force.  Operates in stream or spray mode in the pullout or retracted position. Flow is limited to 1.5 gpm max. Designed to install thru 1 or 3 holes 1-1/4" (32mm) min. Third party certified to CSA B-125, ASME A112.18.1M, NSF 61 Section 9, California Proposition 65, ANSI A117.1 and all applicable requirements referenced therein. ADA compliant. The backflow protection system in this device consists of two independently operating check valves, a primary and a secondary which prevent backflow. Side spray, conventional deck mounting, 2 or 4 hole application, 3/8" compression connection, 7.87" spout height, 1.5 gpm.
Moen Anabelle Pull-Out Kitchen Faucet Delta Signature Pull-Out Kitchen Faucet Delta Classic Pull-Out Kitchen Faucet
High arc pull-down kitchen faucet, one to four hole application, 1/2" IPS connection, 4000 ceramic cartridge,  three-function spray (aerated, pause, rinse), includes soap/lotion dispenser, 66" hose. Deckplate included. 1.5 gpm. Pull-out spray wand provides 38" reach, high-arc spout provides 9" of reach and 8" of height, swings 120 degrees for added convenience, center mount or 8" centers, includes 10-3/4" escutcheon/base. Kitchen pull-out faucet. Flow rate: 2.2 gpm. ADA compliant. Includes soap dispenser.
KINZEL FAUCET KTN CHRM 1 HNDLE Moen Kinzel Pull Out Kitchen Faucet With Soap/Lotion Dispenser Moen Caprillo Pull-Out Kitchen Faucet
Chrome finish, equipped with the Reflex(TM) system for smooth operation, easy movement and secure docking of the pulldown/pullout spray head, features Duralock quick connect system for easy installation, soap/lotion dispenser included for fully coordinated convenience, single hole mount creates a cleaner look against custom countertops, complies with Americans with Disabilities Act (ADA) specifications. Stainless steel, soap dispenser included, single hole mount, Duralock quick connect system, complies with ADA specifications, pullout spray with 68" braided hose, flexible supply lines with 3/8" compression fittings, 1255 Duralast cartridge. 1.5 gpm. Low arc pullout kitchen faucet, one or three hole application, two function sprayer (aerated, rinse), 1/2" IPS connection, 1255 one-piece washerless cartridge, 68" hose, deckplate included.1.5 gpm.
FAUCET KITCHEN ELEC EYE CHROME Delta Pilar Kitchen Faucet Delta Signature Pull-Out Kitchen Faucet
Single-hole installation, Integrated check valve, KliK connection, Neoperl aerator, cover plate for 8" c/c pre-drilled kitchen sink included, Swivel pull-down spout with pause button, push-button diverter and 65? braided nylon flexible hose, 4 AA batteries up to a 2 year lifespan (not included), infrared sensor (with 2.5? - 6.5 cm range) will activate / deactivate flow with hand movement, hand spray will automatically be activated when pulled from its housing, manual override possible for regular handle use, safety timer will automatically close water after 3 minutes of no activity., Maximum flow of 8.3 L/min (2.2 gpm) at 60 psi, Brass body, 3/8" (9/16-24 UNEF) connections with flexible stainless steel braided connectors. High arc faucet. 3- hole 6-16" installation, Diamond Seal valve, 2.5 gpm flow rate at 80psi. Front trigger sprayer activation. Features a stop that allows the spout to swing only 180 degrees allowing ample flexibility to move out of the way while preventing interference with backsplash. Single or three hole installation. Single lever handle with red/blue indicators. Easy side-to-side activated aerated stream or full adjustable spray. Long adjustable pullout spray spout. Straight, staggered supply tubes 6-5/8"& 8" long. Stainless steel vacuum breaker ball. 60" long hose with 38" reach. Maximum 2-1/2" thick deck installation. Standard with 1/2" adapters. Aerate/spray toggle and spray face color, gray. Includes optional 10-3/4" escutcheon/base.
   
 
1