Home > PLUMBING > KITCHEN & BATH > GARBAGE DISPOSALS > SINK DISPOSAL PARTS/ACCESS.
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Thomas & Betts BH122A-UPC Outlet Box Carlon B112HB Handy Box Hubbell 8660 Utility Box
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Thomas & Betts B114R-UPC Switch Box Thomas & Betts B232A-UPC Outlet Box Thomas & Betts B520A-UPC Ceiling Box
Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance.
Hubbell 8192 Outlet Box Thomas & Betts B108B-UPC Outlet Box Thomas & Betts B108R-UPC Outlet Box
Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed.
Carlon B118B-UPC Switch Box Allied Moulded 1098-N Switch Box Carlon B1EXT-CRD Electrical Box
Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4". Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed.
Thomas & Betts SC100RR Low Voltage Box Allied Moulded P241 Switch Box Raco 8190 Outlet Box
For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Residential thermoplastic switch or receptacle box. With angled nails. 3-9/16" depth x 2-1/4" width x 3-3/4" height. 24 cubic inch volume. Fire rating classification of 2 hours in wall and ceiling. UL Listed. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Raco 8189 Ceiling Outlet Box Raco 7887RAC Old Work Cable Box Allied Moulded 1099-N Switch Box
Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
Hubbell 8650 Welded Utility Box Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box
Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Carlon B518A-UPC Ceiling Box Raco 8196 Electrical Box Carlon A615DE-CAR Flexible Raceway Ceiling Box
With captive nails. 18 cubic inch volume. Listed for fixture support up to 50 lb. 3" diameter x 2-3/4" depth. Meets NEMA OS-2, UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Safe, non-conductive. Quick connect. 20.5 cubic inch capacity. Knockouts 1/2" x 3/4". 4" diameter x 2-1/8" depth.
Hubbell 8670 Welded Utility Box Thomas & Betts B120R Outlet Box Raco 662 Drawn Utility Box
Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches.
Thomas & Betts B618RR Ceiling Box Raco 653 Utility Box Raco 8197 Welded Electrical Box
Round old work box with 4 integral swing clamps. Three zip mount retainers. High temperature resistant. 4-1/4" diameter x 2-3/4" depth. UL Listed. Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed. Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed.
Thomas & Betts BH235A Outlet Box Carlon B520P-UPC Ceiling Box Carlon A521DE ENT Flexible Raceway Outlet Box
PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall. Ceiling box with captive nails, ground lug and screw attached. Fixture spacing for 2-3/4" and 3-1/2". 6 integral clamps. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. UL Listed. Meets NEMA OS-2. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed.
Hubbell 665 Utility Box Extension Ring Carlon Super Blue BH525A-UPC Ceiling Box Carlon SC100A 1-Gang Low Voltage Mounting Bracket
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Rigid polycarbonate box used for decorative light fixtures or low voltage devices. Made of a heat resistant thermoplastic material that is lightweight, noncorrosive and nonconductive. Captive nails, 25 cubic inch, 3" deep, large capacity boxes are perfect for specialty lighting, track lighting, or smoke/security devices. Listed for fixture support up to 50 lb. Includes mounting hardware. UL Listed. Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32".
Hubbell 8663 Utility Box Raco 473 Gangable Switch Box Hubbell 8232 Outlet Box
Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed.
Carlon Super Blue BH614R Old Work Ceiling Fan Box Carlon SC200RR Low Voltage Old Work Bracket Raco 8292 Ceiling Pan Box
Spring metal mounting brackets. Fixture rating limit of 10 pounds. Heat resistant. 3-1/2" diameter round old/new work box base, ears and snap-in bracket. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed. Non-metallic sheathed cable wiring system. Clamps in bottom. Four cable knockouts, one 1/2" conduit. 3-1/2" diameter x 1/2" depth. UL Listed.
Raco 528 Gangable Switch Box Raco 161 Drawn Electrical Box Hubbell 8500 Gangable Switch Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn metal 4" octagon box used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. Maximum recommended support load for a  static fixture is 50 lb. TS bracket for wood or metal studs features gauging tabs and recessed nailing spurs. 1-1/2" depth, 1/2" bracket setback, three 1/2" side knockouts, five 1/2" bottom knockouts. 15.5 cubic inch capacity. Combination screw heads allow for fast cover or fixture installation. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B418A-UPC Shallow Outlet Box Thomas & Betts B225R-UPC Outlet Box Carlon Super Blue BH525P Ceiling Box
With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16" Combination ceiling box, hard shell with captive nails and grounding lug. 3" depth. Listed for fixture support up to 50 lb. 4.062" diameter x 3" depth. UL Listed.
Raco 661 Handy Box Raco 400 Gangable Switch Box Thomas & Betts B121ADJ Wall Box
Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C.
Hubbell 8293 Ceiling Pan Box Thomas & Betts B344AB-UPC Outlet Box Hubbell 519 Gangable Switch Box
Five 1/2" bottom conduit knockouts, 6 cubic inch capacity. Acceptable for use in 2-hour rated walls and ceilings. 4" diameter x 1/2" depth. UL Listed. With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls.
Hubbell 8531 Gangable Switch Box Raco 404 Non-Gangable Shallow Switch Box Hubbell 471 Gangable Switch Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed.
Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box Allied Moulded 9318 Handy Box
Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed.
Raco 420 Gangable Switch Box Plumb Pak PP820-12 Splash Guards Raco 560 Gangable Switch Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. Plumb Pak Splash Guard, Disposal, Suitable For Use With: In-Sink-Erator For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 8355 Non-Gangable Switch Box Raco 674 Handy Box Raco 8201 Extension Ring Outlet Box
Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed. For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed.
Raco 7488RAC Old Work Cable Box Allied Moulded 9363-EWK Old Work Switch Box Thomas & Betts B620KR-UPC Ceiling Box
Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Ceiling box with 14.38"-22.5" adjustable bar hanger. 4" diameter x 2-1/4" depth. Fixture spacing for 2-3/4" and 3-1/2". Integral clamps. Listed for fixture support up to 50 pounds. UL Listed.
Raco 567 Gangable Switch Box Hubbell 8203 Electrical Box Extension Ring Thomas & Betts B432A-UPC Outlet Box
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Raco 976 Extension Ring Switch Box Allied Moulded 9351-NK Outlet Box Thomas & Betts BH353A Lightweight Outlet Box
Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. Ceiling box with nails, speed clamps. 50 lb. fixture rated. 2 hour wall and ceiling fire rating classification. 4" diameter x 2-3/8" depth. UL Listed. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box.
Thomas & Betts SC200DV Dual Voltage Outlet Box Allied Moulded 9361-ESK Old Work Switch Box Raco 164 Electrical Box
Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Four cable pryouts and one 1/2" KO side, one - 1/2" KO bottom. Octagon boxes are used in the installation of ceiling or wall light fixtures. TS bracket features gauging tabs and recessed nailing spurs, for wood or metal studs. Acceptable for use in 2-hour fire rated walls and ceilings. 1-1/2" deep - 15.5 cubic inches. UL Listed. UPC bar code.
Hubbell 518 Gangable Switch Box Thomas & Betts B232B-UPC Outlet Box Raco 223 Electrical Box
One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed.
Carlon Super Blue BH118R Old Work Outlet Box Plumb Pak PP855-77 Garbage Disposal Gasket Raco 529 Gangable Switch Box
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed. For In-Sink-Erator disposal. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed.
Carlon A122 ENT Flexible Raceway Outlet Box Raco 545 Non-Gangable Old Work Switch Box Plumb Pak PP820-16 Disposer Splash Guard
Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth. Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Splash guard for garbage disposal. Carded.
Raco 8211 Outlet Box Allied Moulded 2300-NK Switch Box Raco 508 Non-Gangable Switch Box
Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed. Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed.
Hubbell 8257 Welded Outlet Box Raco 487 Gangable Old Work Switch Box Raco 8601 Gangable Switch Box
Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed.
Thomas & Betts B708-SHK Ceiling Pan Box STRAINER DISPOSAL MICROBAN BLK Raco TigerGrip 523 Gangable Old Work Switch Box
Shallow ceiling fan outlet box with mounting screws. 1 integral clamp. Non-conductive high impact lightweight PVC. 5 knock outs, 8 cubic inch capacity. For new work or renovations. Mounts ceiling fan securely to the ceiling joist. Rated for fans up to 35 pounds and fixture up to 50 pounds. 4" diameter x 5/8" depth. UL Listed. Durable plastic construction. Concave design. Helps prevent food and silverware from falling into the disposal. Fits many brands of garbage disposals. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded.
Carlon B620HG-UPC Ceiling Box Carlon Super Blue BH234R Old Work Outlet Box Thomas & Betts B355R Outlet Box
Non-metallic sheathed cable clamps. Ceiling box with 14 -1/4" - 23-1/2" adjustable bar hanger. Fixture spacing for 2-3/4" and 3-1/2". 4" diameter x 2-1/4" depth. Ground lug and screw. 6 integral clamps. Listed for fixture support up to 50 lb. UL Listed, meets NEMA OS-2. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed. Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed.
Raco 2011FBAR Vapor Barrier Box Danco 10428 Splash Guards Sliderbox SB Adjustable Switch/Receptacle Outlet Box
Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Danco Splash Guard, Disposal, Suitable For Use With: Garbage Disposals, Plastic, Black Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings.
Raco 8235 Electrical Box Plumb Pak PP820-15 Garbage Disposal Stopper Raco 295 Ceiling Fan Box
Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed. Fits most disposals. Ceiling fan 4" round pan, 1/2" deep, 6 cubic inches, 5 bottom 1/2" knockouts. Used for new work and renovations. Ceiling fan rated, used in the installation of heavy light fixtures or ceiling fans. Maximum 70 pound fan or 150 pound fixture. Includes nonmetallic sheathed cable connector, mounting hardware, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed.
Raco 605 Gangable Switch Box Plumb Pak PP855-78B Garbage Disposal Drain Elbow Plumb Pak PP855-78 Garbage Disposal Drain Elbow
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed. For In-Sink-Erator disposers. Hang tag For In-Sink-Erator disposers. Hang tag
Carlon B455A-UPC Outlet Box Carlon Super Blue BH525H Ceiling Box REPAIR KIT ISE DISPOSER
REPAIR KIT ISE DISPOSER
Our Price: $4.47
Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. 4" diameter x 2.95" depth. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and clamps to make installation faster. Listed for fixture support up to 50 lb. Hanger bar adjusts from 11-1/2" to 18-1/2". UL Listed. Replaces InSinkErator parts 1491, 1470 and 5490. Includes gasket, bolt, And flange. Designed for use with tailpiece elbow no. 88003. Repair kit for garbage disposals no. 333, 17, and 77.
Raco Romex 176 Electrical Box Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box Raco 8265 Ceiling Outlet Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed.
Thomas & Betts B234ADJ Wall Box Thomas & Betts B720R-SHK Ceiling Fan Box Thomas & Betts BH464A Rigid Outlet Box
Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Non-conductive high impact lightweight PVC. Full 20 cubic inch capacity. 6 integral clamps. 4" diameter x 2-1/4" depth. Used for new work or renovations. Rated for fans up to 35 pounds and fixture up to 50 pounds. Mounts fan to a cross member secured between ceiling joist. Mounting screws included. UL Listed. Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation.
Saf-T-Cap 0105000 Outlet Ceiling Fan Box Allied Moulded 9312-EWK Old Work Outlet Box Carlon Super Blue BH525HP Ceiling Box
For new construction or applications where attic is accessible. Fits all ceiling fans. Maximum load rating for ceiling fans is 70 pounds. 100 pounds for fixtures. 8-32 threads for lightweight fixtures, 10-24 threads for ceiling fans. 3 knockouts for conduit or Romex. 2 Romex clamps. 1-1/2" deep, 15.5 cubic inch capacity. Includes SAF-T-CAP and mounting screws. UL Listed. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed. Ceiling box with hanger bar, adjusts from 11-1/2" to 18-1/2". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Listed for fixture support up to 50 lb. 4" diameter x 3" depth. UL Listed. Ground lug included.
Allied Moulded 3300-NK Outlet Box DISPOSAL BEND 1-1/2X8WHT WKING Danco 10429 Garbage Disposal Stopper
Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed. Designed for use in tubular sink garbage disposal drain applications. Slip-joint connection makes for an easy installation. 1-1/2" . Fits InSinkErator garbage disposals. Black Finish.
Raco 8325 Ceiling Outlet Box Tiger Grip 517 Gangable Switch Box Plumb Pak PP820-11 Garbage Disposal Stopper
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 pound maximum recommended support load. Furnished with 3/8"-18 NPS trade size fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. 1-1/2" deep - 15.5 cubic inches. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed. For In-Sink Erator.
Plumb Pak PP855-79 Garbage Disposal Drain Elbows Raco 680 Switch Box Raco 681 Switch Box
For Waste King disposers. Hang tag. Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B468R Old Work Outlet Box Raco 8326 Ceiling Outlet Box Thomas & Betts BH525L Ceiling Fan Box
Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 lb. maximum recommended support load. Furnished with 3/8"-18 NPS fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. New work ceiling fan box with nails and metal brace for stud finishing. Rated for fans up to 35 pounds and fixtures up to 50 pounds. 4.062" diameter x 3.06" depth. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wire capacity, and comes with molded-in nailing flanges. UL Listed.
Raco 8240 Electrical Box Raco 685 Switch Box Raco 2027-FBAR Round Vapor Barrier Box
Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, 4" round flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Used independently of vapor barrier hats.
Hubbell 683 Switch Box Raco 2002FBAR Vapor Barrier Box Danco 10426 Drain Stopper
Drawn construction for surface mount applications. Conduit wiring system. Eight 1/2" and four 3/4" conduit knockouts (sides). Three 1/2" and two 3/4" conduit knockouts (bottom). 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Black/chrome.
Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box Raco 7120 Ceiling Fan Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box
Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Round polycarbonate, 4" diameter, 12.5 cubic inch black non-metallic ceiling fan support saddle box, used in new work to mount a ceiling fan or heavy light fixture. Supports a 70  pound fan, or 210 pound fixture. Saddle design straddles standard joist. Hands free installation. 1/2" setback. Two 1/2" knock outs on the side. 4 cable clamps, mounting hardware, instructions, and high strength, hardened screws included. 2-hour fire rating, UL Orange Book. UL Listed. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 42 cubic inch volume, two 1/2" knockouts. Internal steel, stud/wood screws. 3-9/16" depth x 4" width x 3-3/4" height. UL listed for 2 hour fire resistive walls.
Raco 296 Ceiling Fan Box Allied Moulded 9313-EWK Old Work Switch Box Allied Moulded 9350-BHK Ceiling Box
Ceiling fan box, 4" octagon, 1-1/2" deep. 3 bottom 1/2" knockouts. Used in new work and renovations. Ceiling fan rated octagon boxes can be used in the installation of heavy light fixtures or ceiling fans. Recommended support load for ceiling fan is 70 pounds, for fixtures is 150 pounds. Includes non-metallic sheathed cable connector, mounting hardware, high strength hardened screws, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Thermoset-fiberglass with ears, wing brackets, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" depth x 5-15/16" x 3-1/4". UL Listed. Four inch round ceiling box with universal bar hanger, adjustable bar assembly from 16" to 24". 4" diameter x 2-7/16" depth. Speed clamps, 50 lb. fixture rated. 2 hour wall and ceiling fire rated,  UL Listed.
Raco 509 Old Work Switch Box Raco 294 Ceiling Fan Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box
Conduit wiring system. Gangable switch box offers the option of constructing a box to hold two or more devices. Adjustable plaster ears allow box to be used in old work applications. Provided old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Two 1/2" bottom knockouts and two 1/2" end knockouts. 2-1/2" deep - 12.5 cubic inches. UL Listed. Ceiling fan box, 4" octagon, 1 bottom 1/2" TKO knockout. 2-1/8" depth, 22.3 cubic inches. Used in new work and renovations. Features FA bracket for wood studs or joists, which allows box to be securely mounted flush. Ceiling fan rated, can be used in the installation of heavy light fixtures or ceiling fans. Recommended support load for ceiling fan is 70 pounds, for fixtures is 150 pounds. Includes non-metallic sheathed cable connector, mounting hardware, high strength hardened screws, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability. 4" diameter x 2-3/4" width, 25 cubic inch volume, two 1/2" knockouts. Internal steel, stud/wood screws. Fixture rating 50 pounds. UL Listed for 2 hour fire resistive walls and ceilings.
Plumb Pak PP335W Sink Disposal Kits Raco 926 Ceiling Fan Box In-sink-erator 08305 Disposer Service Wrench
10"-15".  For In-Sink-Erator. Ceiling fan box with brace, 1-1/2" deep, 15.8 cubic inch box, for new work, to hang ceiling fans and light fixtures between joists or structural members safely and securely. Drawn construction. Maximum 70 pound fan or 90 pound fixture. Brace is adjustable form 16" to 24". Includes 2 end 1/2" knock outs. Acceptable for use in 2-hour fire rated walls and ceilings. UL Listed. A quick, effective tool to help free simple jams. Insert the hex wrench into the center hole in the bottom of the disposer and turn back and forth to free the jam. Works only on InSinkErator manufactured disposers.
Waste King 1025 Splash Guard and Stopper In-sink-erator 08302 Disposer Sound Baffle FLANGE/STOPPER GARB DISPO BLK
For use with any EZ mount disposal. Specifically designed to muffle disposer noise while preventing water and food particles from splashing up. Installs in seconds with no tools and is easily removed for cleaning. For use on Badger products only. (Orgill skus: 944.2096, 465.9652 and 378.5417). Brass garbage disposal flange and stopper. Fits GE, ISE, Kenmore, and Kitchen Aid. Black finish.
Sta-Rite FRC1-D12-S06 Omnifilter Water Filter Cartridge In-sink-erator 09963 Standard Disposer Mount Gasket Culligan Sales IC-100A Water Filter Icemaker Kit
Use in OmniFilter No.F1 faucet-mount water filter to filters rust, sediment, bad taste and odor, and to provide unlimited, fresh filtered water instantly (30 nominal micron rating). Installs in seconds. 0.5 GPM, 3-month/400-gallon life. Usage and incoming water quality may altar life. Replacement sink gasket designed specifically for use on the following InSinkErator models: Badger1, Badger5, Badger5XP, 444, Pro 333, and Septic Disposer. Connects to back of refrigerator to provide better tasting water for ice cubes and beverages. Features conventional nylon fittings to attach to plastic or copper tubing, and granular activated carbon to reduce sediment, chlorine, unpleasant tastes and odors. Up to 12-month life depending on usage and water conditions.
Raco 686 Switch Box Danco 10051 Garbage Stopper Disposal Genie BOX 3GANG 1-5/8DEEP 1/2-3/4 KO
Welded construction. Conduit wiring system. Two 1/2" and two 3/4" knockouts (sides). Three 1/2" and three 3/4" knockouts (bottom). Six 1/2" and six 3/4" knockouts (end). FM type bracket for wood or metal studs. 2-1/2" deep - 47.8 cubic inches. UL Listed. Allows food to flow into the garbage disposal while keeping silverware and other items out. Contains convenient scraper for cleaning sink and scraping food into the disposal. Made of ABS plastic. Used where a number of wiring devices are to be centrally located. Features 1/2" and 3/4" concentric knockouts for use with a wide variety wiring methods. 1-5/8" x 4.5" x 8.63". UL Listed.
In-sink-erator 08300 Garbage Disposer Stopper In-sink-erator 09008 Garbage Disposer Power Cord Raco 936 Ceiling Fan Box with Support
For use on all InSinkErator manufactured disposers. Easy to install,  includes  three-foot UL Listed cord, strain relief clamp, wire connectors and installation instructions. Once installed, disposer plugs directly into a standard wall outlet.  Meets Underwriter Laboratories Inc. SPT-3 category for insulation thickness and moisture resistance. Ceiling fan box with brace, 1-1/2" deep, 15.8 cubic inch capacity. Used to hang ceiling fans and light fixtures between joists or structural members safely and securely in old work applications where access is limited. Brace allows simple expansion, adjustable form 16" to 24". Recommended support load for ceiling fan is 35 pounds, for fixtures is 50 pounds. 4 half inch side, three bottom knock outs. Mounting hardware with high strength, hardened screws and instructions included. Acceptable for use in 2-hour rated walls and ceilings. UL Listed.
Swift SGF-F1 Refrigerator Water Filter Swift SGF-W80 Refrigerator Water Filter Swift SGF-F2 Refrigerator Water Filter
Replacement for Frigidaire WFCB. Replacement for Whirlpool 4396508. Replacement for Frigidaire WF1CB.
Saf-T-Brace 0101000 Brace Ceiling Fan Box Raco 687 Switch Box Culligan FM-25R Water Filter Cartridges
For remodel or new construction. Applications fits 16" to 24" ceiling joists, fits all ceiling fans, and installs without going into the attic. Includes a heavy duty 15.5 cubic inch 1-1/2" deep dual mount box and mounting hardware. Maximum load rating for ceiling fans: 70 pounds, fixtures 100 pounds. Support fan brace has locking screws and teeth. Each end screws into joist independently, with 4 teeth and single screw on each end. 8-32 threads for lightweight fixtures, 10-24 threads for ceiling fans. Six 1/2" Romex or conduit knockouts. UL Listed. Conduit wiring system. Welded construction. FM bracket for wood or metal studs. Eight conduit knockouts (sides). Two conduit knockouts (end).  Four conduit knockouts (bottom). 63.5 cubic inch capacity. 7-19/32" wide x 2-1/2" deep. UL Listed. Replacement cartridge for FM-25R (Orgill sku 568.3081). Polished chrome finish, 2 month or 200 gallon cartridge life.
Square D L211N Safety Switches Carlon SC300PRR Electrical Box Clorox 42401 Brita Water Filter Cartridges
Single phase, 2 pole, 3 wire, solid neutral, 120/240 volt AC. Rated 3 HP at 240 volt AC, with metallic enclosure. Typical uses include workshop or hobby room, water heater, furnace, garage or well pump disconnect. 10,000 AIC (short circuit rating) with plug fuses. Padlock attachment for lock off. 5.00" x 7.63" x 4.00". UL Listed, meets NEMA standard KS1. Nonmetallic ABS material is lightweight, paintable and easy to handle. Recessed low profile design provides ample room behind dry wall and between studs to accommodates cable bend requirements. Hides the wires, cables, cords and plug heads used with flat panel display installations. Has a two gang low voltage opening and a universal one gang opening for an outlet or switch box (boxes, devices, and plates not included). 4 swing out clamps lock the plate securely to the wall, horizontal or vertical mount. 2.72" depth x 5.25" width x 10.5" length. Filters up to 100 gallons of water, and should last about 4 months (for the average family). The FR-200 cartridge does not remove Fluoride. Fits Brita models FF-100/42201 (754.0545) and OPFF-100, and any other model that uses the 'On-Tap' replacement filter cartridge.
Clorox 42617 Brita Square D L111N Fusible Light Duty Safety Switch Culligan FM-15RA Replacement Faucet Mount Water Filter Cartridge
Fits in Brita faucet filtration systems. One filter. Single phase, 1 pole, 2 wire, solid neutral, 120/240 volt AC. Rated 2 HP at 120 volt AC, with metallic enclosure. Typical loads include workshop or hobby room, water heater, furnace, garage or well pump disconnect. 10,000 AIC (short circuit rating) with plug fuses. Padlock attachment for lock off. UL Listed, meets NEMA standard KS1. 5.00" x 7.63" x 4.00". For Culligan No.FM-15R faucet-mount water filter to provide cleaner, better tasting drinking and cooking water from faucet taps by reducing lindane and atrazine, cysts, chlorine taste and odor, bad tastes and odors, and sediment, and by removing more than 99.95% Cryptosporidium and Giardia cysts, 98.9% lead (0.5 micron rating). Up to 2-month/200-gallon life. NSF tested and certified.
In-sink-erator 72376 Disposer Quicklock Mount Assembly Swift SGF-G9 Refrigerator Water Filter Swift SGF-LA22 Refrigerator Water Filter
Twist-On, Twist-Off Quick-Lock design helps ensure fast and easy replacement of existing disposer mounts, polished stainless steel. Replacement for GE MWF also Fits Amana. Replacement for LG 5231JA2002A /LT500.
Swift SGF-W10 Refrigerator Water Filter Swift SGF-M07 Refrigerator Water Filter Swift SGF-W01 Refrigerator Water Filter
Replacement for Whirlpool 4396701. Replacement filter for Maytag UKF-7003. Replacement for Whirlpool 4396510.
Swift SGF-DSB30 Refrigerator Water Filter Swift SGF-W31 Refrigerator Water Filter Swift SGF-W41 Refrigerator Water Filter
Replacement for Samsung DA29-00003B. Replacement for Whirlpool 8171413. Replacement for Whirlpool 8171414.
Plumb Pak PP5417 Garbage Disposal Collars Culligan IC-EZ-1 Ez-Change Icemaker/Refrigerator Dispensers Swift SGF-M9 Refrigerator Water Filter
Plumb Pak Flange and Stopper, Disposal, Suitable For Use With: ISE, GE, Kenmore and Kitchen Aid Disposals, Polished Chrome Kit includes filter head with built-in bracket, RC-EZ-1 level 1 replacement filter cartridge, mounting screws, and filter change reminder sticker. Features twist-on, twist off mechanism, and quick-connect fittings - double water shut-off. 3,000 gallon capacity. NSF certified. Reduces bad taste and odor, chlorine taste and odor, and particulate class III. Replacement for Maytag UKF-8001.
Cutler-Hammer DP221NGB Safety Switches Swift SGF-DSA21 Refrigerator Water Filter Clorox 42201 Brita Water Filters
Steel enclosure. 2 pole, 3 wire, general duty safety switch, plug fuse type, (Type S, T, OR W) fusible with neutral NEMA 1. 120/240 volt rating. 1/2 HP at 120 volt, 1-1/2 HP at 240 volt. Does not have an interlock to prevent opening when switch is in the on position. UL Listed. Replacement for Samsung DA29-00012A. Eliminates 98.5 percent of the Lead and by filtering out Sediment, Chlorine (taste and odor) and also reducing chemicals that may be linked to cancer risk (TTHM, benzene, TCE, toxaphene). Attaches easily in minutes without using tools, fits all standard faucets with quick and easy filter replacement (054.2340). Features a 2-Stage Filter which has an added layer to trap sediment; easy to switch from filtered to unfiltered water. Indicator that flashes red when the filter should be replaced. Change filter every 100 gallons or every 4 months (this may vary depending on water conditions). Compatible with all standard faucets.
Swift SGF-LA50 Refrigerator Water Filter Swift SGF-LA07 Refrigerator Water Filter Culligan FM-15A Replacement Faucet Mount Water Filter Cartridge
Replacement for LG 5231JA2006A / LT600A. Replacement for LG ADQ36006101/ LT700P. Compact, mounts directly onto existing faucets with no tools in seconds. Switches easily from unfiltered to filtered water, simply pull diverter valve stem to provide cleaner, better tasting drinking and cooking water from faucet taps by reducing lead, lindane and atrazine, cysts, chlorine taste and odor, bad tastes and odors, and sediment. Removes more than 99.95% Cryptosporidium and Giardia cysts, 98.9% lead. Use in homes, cottages, boats, or RVs. Includes faucet adapters and No.FM-15R filter cartridge. Up to 200-gallon life. NSF tested and certified.
Swift SGF-LB60 Refrigerator Water Filter Swift SGF-DA20B Refrigerator Water Filter Swift SGF-G23 Refrigerator Water Filter
Replacement for LG 5231JA2006B/ LT600B. Replacement for SAMSUNG DA29-0020B. Replacement for GE MSWF.
Swift SGF-BO90 Refrigerator Water Filter Swift SGF-G22 Refrigerator Water Filter Swift SGF-BO52 Refrigerator Water Filter
Replacement for BOSCH 644845 (9000 ULTRA CLARITY). Replacement for GE GSWF. Replacement for BOSCH 640565 (CUNO CS-52).
Swift SGF-G11 Refrigerator Water Filter Square D D211NCP Safety Switches Square D L221N Safety Switches
Replacement for GE MXRC. Single phase, 2 pole, 3 wire, 2 blades and fuseholders, factory installed solid neutral, 120/240 volt AC. With metallic enclosure for indoor use. Designed to open or close an electrical circuit in general duty applications. Rated 1-1/2 HP. For residential or commercial applications. For PK3GTA-1 field installable service ground bar kit. With plug type fuse protection. Lugs suitable for aluminum or copper conductors. Spring reinforced plated copper fuse clips. ANSI Certified and UL Listed. Single phase, 2 pole, 3 wire (2 blades, fuseholders and 1 neutral), 120/240 volt AC. Rated 3 HP at 240 volt AC, with metallic enclosure. 10,000 AIC (short circuit rating) with class H cartridge fuses. NEMA type 1 enclosure. Terminal lug data: (1) #12 - 6 Al or #14 - 6 Cu. wire. Service ground bar kit PKGTA1 sold separately. Padlock attachment for lock off. UL Listed, meets NEMA standard KS1.
Plumb Pak PP5417VB Garbage Disposal Collars Plumb Pak PP5417DSBN Garbage Disposal Collars Siemens Energy LF211NU Safety Switches
Plumb Pak Flange and Stopper, Disposal, Suitable For Use With: ISE, GE, Kenmore and Kitchen Aid Disposals, Venetian Bronze Plumb Pak Flange and Stopper, Disposal, Suitable For Use With: ISE, GE, Kenmore and Kitchen Aid Disposals, Brushed Nickel Single phase, 2 pole, 3 wire, solid neutral, 120/240 volt. 10,000 AIC with plug fuses (not included). Metallic enclosure. Rated 1-1/2 HP standard/3 HP maximum. Compact size, quick-make, quick-break mechanism. Suitable for use as service entrance equipment. Cover interlock. Bottom cable entry and exit only, no hub provision supplied. Padlocking provision to lock cover closed or to lock in off position. Lugs suitable for copper or aluminum. Silver plated copper conductors. #14-6 AWG line, #14-8 load lug wire ranges. 5-1/2" x 8-1/4" x 5-13