Home > PLUMBING > KITCHEN & BATH > GARBAGE DISPOSALS
Choose a sub category:
FLASHLIGHTS SINK DISPOSALS BATTERIES
SINK DISPOSAL PARTS/ACCESS. TOOLS & TESTERS DOORBELLS & CHIMES
FIRE/HOME PROTECTION TELEPHONE & ACCESSORIES AUDIO & VIDEO SUPPLIES
COMPUTER ACCESSORIES ELECTRONICS
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Thomas & Betts BH122A-UPC Outlet Box Raco 8977 Electrical Box Supports Carlon B112HB Handy Box
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation.
Hubbell 8660 Utility Box Thomas & Betts B114R-UPC Switch Box Thomas & Betts B232A-UPC Outlet Box
Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4".
Thomas & Betts B520A-UPC Ceiling Box Hubbell 8192 Outlet Box Halex 26279 Switch Box Support
With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance. Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. Use to suport attachment of an outlet box in drywall, paneling, etc., in the absence of a structure member. Installed in pairs.
Thomas & Betts B108B-UPC Outlet Box Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box
New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4".
Allied Moulded 1098-N Switch Box Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05".
Raco 8190 Outlet Box Raco 8189 Ceiling Outlet Box Raco 7887RAC Old Work Cable Box
Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Allied Moulded 1099-N Switch Box GB PPR-1500 Insulated Clamp Gardner Bender PPC-1525 1-Hole Cable Clamp
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. GB Insulated Clamp, 3/8 in Opening, Steel, Black, Rubber Cushion Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F.
Gardner Bender PPC-1538 1-Hole Cable Clamp Gardner Bender PPC-1550 1-Hole Cable Clamp Gardner Bender PPC-1575 1-Hole Cable Clamp
Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F. Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F. Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F.
Gardner Bender PPC-1600 1-Hole Cable Clamp Hubbell 8650 Welded Utility Box Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box
Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Jandorf 61453 Cable Clamp Jandorf 61454 Cable Clamp Jandorf 61455 Cable Clamp
Secures cable, tubing and wires. Secures cable, tubing and wires. Secures cable, tubing and wires.
Jandorf 61457 Cable Clamp Jandorf 61461 Cable Clamp Jandorf 61464 Cable Clamp
Secures cable, tubing and wires. Secures cable, tubing and wires. Secures cable, tubing and wires.
Jandorf 61466 Cable Clamp Jandorf 61467 Cable Clamp Jandorf 61469 Cable Clamp
Secures cable, tubing and wires. Secures cable, tubing and wires. Secures cable, tubing and wires.
Jandorf 61471 Cable Clamp Jandorf 61472 Cable Clamp Jandorf 61456 Cable Clamp
Secures cable, tubing and wires. Secures cable, tubing and wires. Secures cable, tubing and wires.
Jandorf 61450 Cable Clamp Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Jandorf 61449 Cable Clamp
Secures cable, tubing and wires. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Secures cable, tubing and wires.
Jandorf 61452 Cable Clamp Jandorf 61447 Cable Clamp Carlon B518A-UPC Ceiling Box
Secures cable, tubing and wires. Secures cable, tubing and wires. With captive nails. 18 cubic inch volume. Listed for fixture support up to 50 lb. 3" diameter x 2-3/4" depth. Meets NEMA OS-2, UL Listed.
Raco 8196 Electrical Box Jandorf 61459 Cable Clamp Jandorf 61460 Cable Clamp
Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Secures cable, tubing and wires. Secures cable, tubing and wires.
Jandorf 61463 Cable Clamp Jandorf 61468 Cable Clamp Carlon A615DE-CAR Flexible Raceway Ceiling Box
Secures cable, tubing and wires. Secures cable, tubing and wires. Safe, non-conductive. Quick connect. 20.5 cubic inch capacity. Knockouts 1/2" x 3/4". 4" diameter x 2-1/8" depth.
Hubbell 8670 Welded Utility Box Thomas & Betts B120R Outlet Box Raco 662 Drawn Utility Box
Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches.
Jandorf 61448 Cable Clamp Jandorf 61451 Cable Clamp Jandorf 61462 Cable Clamp
Secures cable, tubing and wires. Secures cable, tubing and wires. Secures cable, tubing and wires.
Thomas & Betts B618RR Ceiling Box Raco 653 Utility Box Raco 8197 Welded Electrical Box
Round old work box with 4 integral swing clamps. Three zip mount retainers. High temperature resistant. 4-1/4" diameter x 2-3/4" depth. UL Listed. Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed. Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed.
Jandorf 61446 Cable Clamp Jandorf 61458 Cable Clamp Thomas & Betts BH235A Outlet Box
Secures cable, tubing and wires. Secures cable, tubing and wires. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall.
Gardner Bender PPC-1575UVB 1-Hole Cable Clamp Gardner Bender PPC-1525UVB 1-Hole Cable Clamp Gardner Bender PPC-1550UVB 1-Hole Cable Clamp
Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F. Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F. Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F.
Gardner Bender PPC-1538UVB 1-Hole Cable Clamp Carlon B520P-UPC Ceiling Box Carlon A521DE ENT Flexible Raceway Outlet Box
Flexible shape conforms to wires and cables. Holds harnesses, cables and tubing for construction, maintenance and assembly-line operations. Tough, durable, yet extremely lightweight with clean, smooth edges for easy handling. Working temperature range of -66 to 340 degrees F. Ceiling box with captive nails, ground lug and screw attached. Fixture spacing for 2-3/4" and 3-1/2". 6 integral clamps. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. UL Listed. Meets NEMA OS-2. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed.
Hubbell 665 Utility Box Extension Ring Carlon Super Blue BH525A-UPC Ceiling Box Carlon SC100A 1-Gang Low Voltage Mounting Bracket
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Rigid polycarbonate box used for decorative light fixtures or low voltage devices. Made of a heat resistant thermoplastic material that is lightweight, noncorrosive and nonconductive. Captive nails, 25 cubic inch, 3" deep, large capacity boxes for specialty lighting, track lighting, or smoke/security devices. Listed for fixture support up to 50 lbs. Includes mounting hardware. UL Listed. Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32".
Jandorf 61412 Cable Clip Hubbell 8663 Utility Box Raco 473 Gangable Switch Box
Jandorf Cable Clip, Series: 61412, 3/8 in Diameter, UL Listed, For Indoor Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed.
Jandorf 61406 Cable Clip Jandorf 61470 Cable Clamp Hubbell 8232 Outlet Box
Jandorf Cable Clip, Series: 61406, 1/2 in Diameter, White, UL Listed, For Indoor Secures cable, tubing and wires. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed.
Carlon Super Blue BH614R Old Work Ceiling Fan Box Carlon SC200RR Low Voltage Old Work Bracket Raco 8292 Ceiling Pan Box
Spring metal mounting brackets. Fixture rating limit of 10 pounds. Heat resistant. 3-1/2" diameter round old/new work box base, ears and snap-in bracket. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed. Non-metallic sheathed cable wiring system. Clamps in bottom. Four cable knockouts, one 1/2" conduit. 3-1/2" diameter x 1/2" depth. UL Listed.
Raco 528 Gangable Switch Box Raco 161 Drawn Electrical Box Hubbell 8500 Gangable Switch Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn metal 4" octagon box used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. Maximum recommended support load for a  static fixture is 50 lb. TS bracket for wood or metal studs features gauging tabs and recessed nailing spurs. 1-1/2" depth, 1/2" bracket setback, three 1/2" side knockouts, five 1/2" bottom knockouts. 15.5 cubic inch capacity. Combination screw heads allow for fast cover or fixture installation. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B418A-UPC Shallow Outlet Box Thomas & Betts B225R-UPC Outlet Box LOCK CORD S TYPE PLASTIC YEL
With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16" Locking system for keeping extension cord plug connections in place. S shape, constructed of heavy-duty plastic.
Carlon Super Blue BH525P Ceiling Box Jandorf 61536 Loom Clamp Raco 661 Handy Box
Combination ceiling box, hard shell with captive nails and grounding lug. 3" depth. Listed for fixture support up to 50 lb. 4.062" diameter x 3" depth. UL Listed. Coated wire clamps. Card of 2. Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed.
Raco 400 Gangable Switch Box Thomas & Betts B121ADJ Wall Box Hubbell 8293 Ceiling Pan Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Five 1/2" bottom conduit knockouts, 6 cubic inch capacity. Acceptable for use in 2-hour rated walls and ceilings. 4" diameter x 1/2" depth. UL Listed.
Thomas & Betts B344AB-UPC Outlet Box Jandorf 61538 Loom Clamp Hubbell 519 Gangable Switch Box
With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. Coated wire clamps. Card of 2. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls.
Hubbell 8531 Gangable Switch Box Raco 404 Non-Gangable Shallow Switch Box Culligan OR-34A Water Filter Accessories
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Use on comparable sized filter housing.
Hubbell 471 Gangable Switch Box Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box
Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed. Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length.
Allied Moulded 9318 Handy Box WINDER CORD PLASTIC BLACK     Raco 420 Gangable Switch Box
Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed. H-frame styled winder, with a leverage grip for easy winding. Holds up to 150 feet of 16/AWG cord. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed.
Jandorf 61407 Cable Clip Raco 560 Gangable Switch Box Jandorf 61408 Cable Clip
Jandorf Cable Clip, Series: 61407, 1/4 in Diameter, UL Listed, For Indoor For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed. Jandorf Cable Clip, Series: 61408, 1/4 in Diameter, UL Listed, For Indoor
Raco 8355 Non-Gangable Switch Box Jandorf 61535 Loom Clamp Jandorf 61537 Loom Clamp
Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. Coated wire clamps. Card of 2. Coated wire clamps. Card of 2.
Jandorf 61411 Cable Clip Jandorf 61531 Cushion Clamp Jandorf 61539 Loom Clamp
Jandorf Cable Clip, Series: 61411, 1/8 in Diameter, UL Listed, For Indoor Coated wire clamps. Card of 2. Coated wire clamps. Card of 2.
Jandorf 61540 Loom Clamp Jandorf 61547 Loom Clamp Raco 674 Handy Box
Coated wire clamps. Card of 2. Coated wire clamps. Card of 2. For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed.
Raco 8201 Extension Ring Outlet Box Raco 7488RAC Old Work Cable Box Allied Moulded 9363-EWK Old Work Switch Box
For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed. Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed.
Raco 920 Steel Bar Hangers Thomas & Betts B620KR-UPC Ceiling Box Jandorf 61525 Cushion Clamp
Holding prong, box clip holds box in place for nailing. Design resists bending and twisting. With stud. Length 14-1/4" thru 22-1/2". With locking tabs to hold bar in position. UL Listed. Ceiling box with 14.38"-22.5" adjustable bar hanger. 4" diameter x 2-1/4" depth. Fixture spacing for 2-3/4" and 3-1/2". Integral clamps. Listed for fixture support up to 50 pounds. UL Listed. Coated wire clamps. Card of 2.
Raco 567 Gangable Switch Box Hubbell 8203 Electrical Box Extension Ring Jandorf 61405 Cable Clip
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. Jandorf Cable Clip, Series: 61405, 1 in Diameter, UL Listed, For Indoor
Thomas & Betts B432A-UPC Outlet Box Raco 976 Extension Ring Switch Box Allied Moulded 9351-NK Outlet Box
With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. Ceiling box with nails, speed clamps. 50 lb. fixture rated. 2 hour wall and ceiling fire rating classification. 4" diameter x 2-3/8" depth. UL Listed.
Jandorf 61527 Cushion Clamp Thomas & Betts BH353A Lightweight Outlet Box Jandorf 61410 Cable Clip
Coated wire clamps. Card of 2. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. Jandorf Cable Clip, Series: 61410, 1/8 in Diameter, UL Listed, For Indoor
Jandorf 61533 Cushion Clamp Thomas & Betts SC200DV Dual Voltage Outlet Box Allied Moulded 9361-ESK Old Work Switch Box
Coated wire clamps. Card of 2. Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed.
Gardner Bender GWC-1510 Stick-On Wire Clip Jandorf 61534 Loom Clamp Raco 164 Electrical Box
Fastens bell, speaker, telephone and other small wires securely along walls, baseboards. Peel off backing. Coated wire clamps. Card of 2. Four cable pryouts and one 1/2" KO side, one - 1/2" KO bottom. Octagon boxes are used in the installation of ceiling or wall light fixtures. TS bracket features gauging tabs and recessed nailing spurs, for wood or metal studs. Acceptable for use in 2-hour fire rated walls and ceilings. 1-1/2" deep - 15.5 cubic inches. UL Listed. UPC bar code.
Hubbell 518 Gangable Switch Box Jandorf 61530 Cushion Clamp Thomas & Betts B232B-UPC Outlet Box
One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. Coated wire clamps. Card of 2. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3".
Raco 223 Electrical Box Carlon Super Blue BH118R Old Work Outlet Box Plumb Pak PP820-12 Splash Guards
Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed. Plumb Pak Splash Guard, Disposal, Suitable For Use With: In-Sink-Erator
Raco 529 Gangable Switch Box Kwik Klips GKK-1575 Adjustable Ratcheting Cable Holder Kwik Klips GKK-1538 Cable Holder Clip
Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Mounts bundles, cables, cords, tools, etc. to drywall, wood and painted surfaces. Ratcheting/releasable feature allows adjustment to range of bundle diameters. Made of tough 6/6 nylon material. Mounts bundles, cables, cords, tools, etc. to drywall, wood and painted surfaces. Ratcheting/releasable feature allows adjustment to range of bundle diameters. Made of tough 6/6 nylon material.
Kwik Klips GKK-1550 Cable Holder Clip Carlon A122 ENT Flexible Raceway Outlet Box Raco 545 Non-Gangable Old Work Switch Box
Mounts bundles, cables, cords, tools, etc. to drywall, wood and painted surfaces. Ratcheting/releasable feature allows adjustment to range of bundle diameters. Made of tough 6/6 nylon material. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth. Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 8211 Outlet Box Allied Moulded 2300-NK Switch Box Jandorf 61526 Cushion Clamp
Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed. Coated wire clamps. Card of 2.
Raco 508 Non-Gangable Switch Box Hubbell 8257 Welded Outlet Box Raco 487 Gangable Old Work Switch Box
Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed. Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches.
Raco 8601 Gangable Switch Box Thomas & Betts B708-SHK Ceiling Pan Box Raco TigerGrip 523 Gangable Old Work Switch Box
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed. Shallow ceiling fan outlet box with mounting screws. 1 integral clamp. Non-conductive high impact lightweight PVC. 5 knock outs, 8 cubic inch capacity. For new work or renovations. Mounts ceiling fan securely to the ceiling joist. Rated for fans up to 35 pounds and fixture up to 50 pounds. 4" diameter x 5/8" depth. UL Listed. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded.
Carlon B620HG-UPC Ceiling Box Coleman 2803 H-Frame Extension Cord Caddy with Handle Carlon Super Blue BH234R Old Work Outlet Box
Non-metallic sheathed cable clamps. Ceiling box with 14 -1/4" - 23-1/2" adjustable bar hanger. Fixture spacing for 2-3/4" and 3-1/2". 4" diameter x 2-1/4" depth. Ground lug and screw. 6 integral clamps. Listed for fixture support up to 50 lb. UL Listed, meets NEMA OS-2. Stores extension cords, trouble lights, coaxial cable, TV antenna wire, speaker wire, rope, holiday lights and much more. Heavier duty than most H-frame cord storage devices.  Built-in carry handle, one-piece construction, hole on side for wall mounting. Clip secures tail end of cord. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed.
Thomas & Betts B355R Outlet Box Raco 2011FBAR Vapor Barrier Box Danco 10428 Splash Guards
Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Danco Splash Guard, Disposal, Suitable For Use With: Garbage Disposals, Plastic, Black
Sliderbox SB Adjustable Switch/Receptacle Outlet Box GB PAC-1525 EZ Clip Raco 8235 Electrical Box
Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings. GB EZ Clip, 1/4 in Opening, Aluminum, For Data/Com Cable Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed.
Raco 295 Ceiling Fan Box Jandorf 61532 Cushion Clamp Raco 605 Gangable Switch Box
Ceiling fan 4" round pan, 1/2" deep, 6 cubic inches, 5 bottom 1/2" knockouts. Used for new work and renovations. Ceiling fan rated, used in the installation of heavy light fixtures or ceiling fans. Maximum 70 pound fan or 150 pound fixture. Includes nonmetallic sheathed cable connector, mounting hardware, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Coated wire clamps. Card of 2. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed.
Jandorf 61529 Cushion Clamp Carlon B455A-UPC Outlet Box Carlon Super Blue BH525H Ceiling Box
Coated wire clamps. Card of 2. Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. 4" diameter x 2.95" depth. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and clamps to make installation faster. Listed for fixture support up to 50 lb. Hanger bar adjusts from 11-1/2" to 18-1/2". UL Listed.
Jandorf 61404 Cable Clip Powerzone OR501608 SJTW Round Extension Cord Jandorf 61528 Cushion Clamp
Jandorf Cable Clip, Series: 61404, 0.563 in Diameter, UL Listed, For Indoor Rated for 300 volt, grounded. Manufactured with copper conductors and solid molded plugs and two layers of insulation, one around each conductor and a second outer jacket that won't mark floors or walls and resists deterioration from moisture and abrasion. UL, cULus  Listed, meets OSHA specifications. Sleeved. Coated wire clamps. Card of 2.
Plumb Pak PP855-77 Garbage Disposal Gasket Star Rite OK25 Replacement Filter Housing O-Ring Raco Romex 176 Electrical Box
For In-Sink-Erator disposal. For use with No.U25 Omni whole house water filter. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed.
STRAINER DISPOSAL MICROBAN BLK Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box Raco 8265 Ceiling Outlet Box
Durable plastic construction. Concave design. Helps prevent food and silverware from falling into the disposal. Fits many brands of garbage disposals. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed.
Plumb Pak PP820-16 Disposer Splash Guard Sta-Rite K4-M6-S06 O-ring CLIP ELECTRICAL ASSORTMNT 28PC
Splash guard for garbage disposal. Carded. For use with Omni whole house filters Nos.OB1, OB5, R12, and R14; and Omni under-sink water filters Nos.CBF20, SFM2, UC2. CBF1, CBF3, OT32, OB3, and RO2000. Will also fit Nos.BC1, TC3, UC2, U400. U500, U600, U700, Omni Super, and Total 2. If your unit uses blue o-ring, replaces Total Plus, Omni Regular and Omni Deluxe o-rings. Bagged. Spring clips have PVC insulation, equal numbers of black & red, can be used to repair broken leads on test equipment & chargers. Neatly organized PVC storage case with lid.
Thomas & Betts B234ADJ Wall Box REPAIR KIT ISE DISPOSER       Thomas & Betts B720R-SHK Ceiling Fan Box
REPAIR KIT ISE DISPOSER
Our Price: $4.80
Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Replaces InSinkErator parts 1491, 1470 and 5490. Includes gasket, bolt, And flange. Designed for use with tailpiece elbow no. 88003. Repair kit for garbage disposals no. 333, 17, and 77. Non-conductive high impact lightweight PVC. Full 20 cubic inch capacity. 6 integral clamps. 4" diameter x 2-1/4" depth. Used for new work or renovations. Rated for fans up to 35 pounds and fixture up to 50 pounds. Mounts fan to a cross member secured between ceiling joist. Mounting screws included. UL Listed.
Thomas & Betts BH464A Rigid Outlet Box Allied Moulded 9312-EWK Old Work Outlet Box Carlon Super Blue BH525HP Ceiling Box
Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed. Ceiling box with hanger bar, adjusts from 11-1/2" to 18-1/2". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Listed for fixture support up to 50 lb. 4" diameter x 3" depth. UL Listed. Ground lug included.
Allied Moulded 3300-NK Outlet Box Jandorf 61413 Cable Clip DISPOSAL BEND 1-1/2X8WHT WKING
Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed. Jandorf Cable Clip, Series: 61413, 5/16 in Diameter, UL Listed, For Indoor Designed for use in tubular sink garbage disposal drain applications. Slip-joint connection makes for an easy installation. 1-1/2" .
CORD EXT OTD ORG SJTW 16/2 8FT Plumb Pak PP820-15 Garbage Disposal Stopper Danco 10429 Garbage Disposal Stopper
Orange Outdoor Extension Cord. Heavy Duty. 16 Gauge with 2 Conductors. Fits most disposals. Fits InSinkErator garbage disposals. Black Finish.
Sta-Rite OW30-S6-S06 Tank Wrench Culligan OR-100 Water Filter Accessories Raco 8325 Ceiling Outlet Box
For use with Omnir filters Nos. CBF1, SFM2, USF1,  CBF3, USF3, SFM2, USM2, OCT2, US30, US32, RO2050, and RO2000. Carded. Use on comparable sized filter housing. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 pound maximum recommended support load. Furnished with 3/8"-18 NPS trade size fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. 1-1/2" deep - 15.5 cubic inches.
Tiger Grip 517 Gangable Switch Box Plumb Pak PP855-78B Garbage Disposal Drain Elbow Plumb Pak PP855-78 Garbage Disposal Drain Elbow
Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed. For In-Sink-Erator disposers. Hang tag For In-Sink-Erator disposers. Hang tag
Culligan 01019187 Water Filter Accessories Saf-T-Cap 0105000 Outlet Ceiling Fan Box Culligan SW-2A Water Filter Accessories
Single housing bracket is a "U" shaped mounting bracket for 3/4" inlet/outlet standard whole house housings. The UB-1 mounts standard whole house water filter housings and helps support the weight of the water filter. Screws are included with the UB-1 mounting bracket for securing the water filter housing to the wall. Use with: Culligan HF-150 (883.4442) and Culligan HF-360 (306.9820) Water Filter Housings. For new construction or applications where attic is accessible. Fits all ceiling fans. Maximum load rating for ceiling fans is 70 pounds. 100 pounds for fixtures. 8-32 threads for lightweight fixtures, 10-24 threads for ceiling fans. 3 knockouts for conduit or Romex. 2 Romex clamps. 1-1/2" deep, 15.5 cubic inch capacity. Includes SAF-T-CAP and mounting screws. UL Listed. Use on comparable sized filter housing to replace filter cartridge.
Raco 680 Switch Box Culligan SW-1 Small Filter Housing Wrench Raco 681 Switch Box
Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Use on comparable sized filter housing to replace filter cartridge. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B468R Old Work Outlet Box Raco 8326 Ceiling Outlet Box Thomas & Betts BH525L Ceiling Fan Box
Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 lb. maximum recommended support load. Furnished with 3/8"-18 NPS fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. New work ceiling fan box with nails and metal brace for stud finishing. Rated for fans up to 35 pounds and fixtures up to 50 pounds. 4.062" diameter x 3.06" depth. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wire capacity, and comes with molded-in nailing flanges. UL Listed.
Raco 8240 Electrical Box Raco 685 Switch Box Raco 2027-FBAR Round Vapor Barrier Box
Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-ho