Home > PLUMBING > KITCHEN & BATH > TOILET SEATS > TOILET SEATS - SOFT
Choose a sub category:
HOUSEHOLD EXTENSION CORDS EXTENSION CORDS WITH GFCI OUTDOOR EXTENSION CORDS
MULTI OUTLET EXTENSION CORDS FLAT EXTENSION CORDS/NON UL AIR CONDITIONER CORDS
RANGE/DRYER CORDS APPLIANCE REPLACEMENT CORDS GENERATOR CORDS
POWER ADAPTER CORDS POWER BLOCKS CORD STORAGE & ADAPTERS
CORD REELS CORD PROTECTORS
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Thomas & Betts BH122A-UPC Outlet Box Carlon B112HB Handy Box Hubbell 8660 Utility Box
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Thomas & Betts B114R-UPC Switch Box Thomas & Betts B232A-UPC Outlet Box Thomas & Betts B520A-UPC Ceiling Box
Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance.
Hubbell 8192 Outlet Box Thomas & Betts B108B-UPC Outlet Box Gardner Bender GSE-15310 Service Entrance Staple
Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Secures service entrance cable. Pointed offset legs drive in straight, will not split wood. High quality carbon steel for durability and easy nailing.
Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box Allied Moulded 1098-N Switch Box
Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4". Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box Raco 8190 Outlet Box
Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Raco 8189 Ceiling Outlet Box Gardner Bender MS-1550T Cable Staple Raco 7887RAC Old Work Cable Box
Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Allied Moulded 1099-N Switch Box Gardner Bender MS Cable Staple Hubbell 8650 Welded Utility Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed.
Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box Gardner Bender MS-1575T Cable Staple Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box
Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Carlon B518A-UPC Ceiling Box Raco 8196 Electrical Box Carlon A615DE-CAR Flexible Raceway Ceiling Box
With captive nails. 18 cubic inch volume. Listed for fixture support up to 50 lb. 3" diameter x 2-3/4" depth. Meets NEMA OS-2, UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Safe, non-conductive. Quick connect. 20.5 cubic inch capacity. Knockouts 1/2" x 3/4". 4" diameter x 2-1/8" depth.
Hubbell 8670 Welded Utility Box Thomas & Betts B120R Outlet Box Gardner Bender MSI-1525T Insulated Cable Staple
Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation.
Raco 662 Drawn Utility Box Gardner Bender PSG Low Voltage Cable Staple Thomas & Betts B618RR Ceiling Box
Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches. For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. Round old work box with 4 integral swing clamps. Three zip mount retainers. High temperature resistant. 4-1/4" diameter x 2-3/4" depth. UL Listed.
Raco 653 Utility Box Raco 8197 Welded Electrical Box Gardner Bender MSI-50B Insulated Cable Staple
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed. Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed. Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation.
Thomas & Betts BH235A Outlet Box Carlon B520P-UPC Ceiling Box Carlon A521DE ENT Flexible Raceway Outlet Box
PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall. Ceiling box with captive nails, ground lug and screw attached. Fixture spacing for 2-3/4" and 3-1/2". 6 integral clamps. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. UL Listed. Meets NEMA OS-2. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed.
Gardner Bender PWS Low Voltage Kwik Mount Cable Staple Gardner Bender PSB Cable Staple Gardner Bender MS-1555 Cable Staple
Quick fastening and guiding of wires. Wires easily snap in or out of two usable sides. Use to secure Christmas light sets, sound system wires, etc. Holds category 5 cable for datacom. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable.
Gardner Bender GSE-15410 Service Entrance Staple Gardner Bender GSE-402 Service Entrance Strap Gardner Bender MS Cable Staple
Secures service entrance cable. Pointed offset legs drive in straight, will not split wood. High quality carbon steel for durability and easy nailing. Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable.
Gardner Bender GSE-205 Service Entrance Strap STAPLE METAL INSULATED 1/2IN  Hubbell 665 Utility Box Extension Ring
Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage. Metal insulated staples secures and protects non-metallic (NM), BX, MC, AC and UF cable. Insulator made from durable polyethylene. Plastic insulator protects cables and helps prevent arc faults. Dimensions: 1/2"W x 1-1/2"L. Silver/red color. Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Carlon Super Blue BH525A-UPC Ceiling Box Carlon SC100A 1-Gang Low Voltage Mounting Bracket Gardner Bender MSB Insulated Low Voltage Cable Staple
Rigid polycarbonate box used for decorative light fixtures or low voltage devices. Made of a heat resistant thermoplastic material that is lightweight, noncorrosive and nonconductive. Captive nails, 25 cubic inch, 3" deep, large capacity boxes are perfect for specialty lighting, track lighting, or smoke/security devices. Listed for fixture support up to 50 lb. Includes mounting hardware. UL Listed. Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". U-shaped staple fastens audio speaker and bell wire, insulated cradle protects wire.
Gardner Bender MSW Insulated Cable Staple Gardner Bender GSE-304 Service Entrance Strap Hubbell 8663 Utility Box
U-shaped staple fastens audio speaker and bell wire, insulated cradle protects wire. Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage. Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Raco 473 Gangable Switch Box Gardner Bender PS-50 Insulated Cable Staple Powerzone OR660606 SPT-2 Extension Cord
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed. For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only.
Powerzone OR670606 SPT-2 Extension Cord Hubbell 8232 Outlet Box Carlon Super Blue BH614R Old Work Ceiling Fan Box
Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed. Spring metal mounting brackets. Fixture rating limit of 10 pounds. Heat resistant. 3-1/2" diameter round old/new work box base, ears and snap-in bracket. UL Listed.
Carlon SC200RR Low Voltage Old Work Bracket Raco 8292 Ceiling Pan Box Gardner Bender GSE-105 Service Entrance Strap
For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed. Non-metallic sheathed cable wiring system. Clamps in bottom. Four cable knockouts, one 1/2" conduit. 3-1/2" diameter x 1/2" depth. UL Listed. Plastic insulated straps secure service entrance cable. Electro-zinc plated nails. Cradles constructed of polyethylene. Straps stabilized against UV rays and extreme cold, withstands deterioration and breakage.
Gardner Bender PSB Low Voltage Cable Staple Gardner Bender PMB-1525 Low Voltage Cable Strap Gardner Bender MS-1577 Cable Staple
For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable.
Gardner Bender PSW-1650T Cable Staple Gardner Bender PCC Low Voltage Clip-On Cable Staple GB-Gardner Bender MSI-1575 Cable Staples
For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. Used for indoor and outdoor applications. UV resistant polyethylene saddle. Zinc plated nails. Secures RG-49, RG-59 and RG-6 coaxial cables. With clip-on feature. Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation.
GB PTP-25T Category 3 and 5 Low Voltage Data Staple Raco 528 Gangable Switch Box Raco 161 Drawn Electrical Box
GB Data Staple, Category 3 and 5, Low Voltage, 1/4 in Crown, Polyethylene, Zinc Plated, Blue, Suitable For Use With: RJ-11, RJ-12, RJ-45, Category 3 and Category 5 Wire to Wood, 1/4 in Width, For Mounting to Wood Surfaces Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn metal 4" octagon box used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. Maximum recommended support load for a  static fixture is 50 lb. TS bracket for wood or metal studs features gauging tabs and recessed nailing spurs. 1-1/2" depth, 1/2" bracket setback, three 1/2" side knockouts, five 1/2" bottom knockouts. 15.5 cubic inch capacity. Combination screw heads allow for fast cover or fixture installation. Acceptable for use in 2-hour rated walls and ceilings. UL Listed.
Hubbell 8500 Gangable Switch Box Carlon B418A-UPC Shallow Outlet Box Thomas & Betts B225R-UPC Outlet Box
Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16"
Carlon Super Blue BH525P Ceiling Box Gardner Bender PS-75 Insulated Cable Staple Raco 661 Handy Box
Combination ceiling box, hard shell with captive nails and grounding lug. 3" depth. Listed for fixture support up to 50 lb. 4.062" diameter x 3" depth. UL Listed. For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed.
Raco 400 Gangable Switch Box Thomas & Betts B121ADJ Wall Box Hubbell 8293 Ceiling Pan Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Five 1/2" bottom conduit knockouts, 6 cubic inch capacity. Acceptable for use in 2-hour rated walls and ceilings. 4" diameter x 1/2" depth. UL Listed.
Thomas & Betts B344AB-UPC Outlet Box Hubbell 519 Gangable Switch Box Hubbell 8531 Gangable Switch Box
With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed.
Raco 404 Non-Gangable Shallow Switch Box Culligan OR-34A Water Filter Accessories Hubbell 471 Gangable Switch Box
Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Use on comparable sized filter housing. Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed.
Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box Gardner Bender PS-1550T Insulated Cable Staple
Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening.
Allied Moulded 9318 Handy Box Raco 420 Gangable Switch Box Raco 560 Gangable Switch Box
Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed.
Gardner Bender PS-1575T2 Insulated Cable Staple Raco 8355 Non-Gangable Switch Box Raco 674 Handy Box
For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed.
Powerzone OR780609 SPT-2 Extension Cord Raco 8201 Extension Ring Outlet Box Raco 7488RAC Old Work Cable Box
Household cord, indoor only. 16/2 SPT-2. One outlet to three. For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed. Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity.
Gardner Bender MDI Insulated High Impact Cable Staple Allied Moulded 9363-EWK Old Work Switch Box Thomas & Betts B620KR-UPC Ceiling Box
Insulated staples protect and secure Romex, NM, BX and UF. PVC insulation protects cable from damage due to mis-hit and overdriving, prevents a short circuit if wire insulation is damaged. Highly visible color coded for size and application. Card/40. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Ceiling box with 14.38"-22.5" adjustable bar hanger. 4" diameter x 2-1/4" depth. Fixture spacing for 2-3/4" and 3-1/2". Integral clamps. Listed for fixture support up to 50 pounds. UL Listed.
Raco 567 Gangable Switch Box Gardner Bender PCS-1600T Low Voltage Masonry Staple Hubbell 8203 Electrical Box Extension Ring
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Hardened nails can penetrate cement block, mortar or plaster surfaces. For cable TV and other hard-surface installation. Plastic cradle provides added protection to cable jackets. Freeze resistant. UV protected. (Black). Secures RG-49, RG-59 and RG-6 coaxial cables. PCS-1600 has clip-on feature. For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed.
Thomas & Betts B432A-UPC Outlet Box Raco 976 Extension Ring Switch Box Allied Moulded 9351-NK Outlet Box
With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. Ceiling box with nails, speed clamps. 50 lb. fixture rated. 2 hour wall and ceiling fire rating classification. 4" diameter x 2-3/8" depth. UL Listed.
Thomas & Betts BH353A Lightweight Outlet Box Gardner Bender PSW Low Voltage Cable Staple Thomas & Betts SC200DV Dual Voltage Outlet Box
Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed. Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved.
Allied Moulded 9361-ESK Old Work Switch Box Powerzone OR670609 SPT-2 Extension Cord Powerzone OR660609 SPT-2 Extension Cord
Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only. Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only.
Gardner Bender MSI Insulated Cable Staple Gardner Bender PR Low Voltage Cable Staple Raco 164 Electrical Box
Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed. Four cable pryouts and one 1/2" KO side, one - 1/2" KO bottom. Octagon boxes are used in the installation of ceiling or wall light fixtures. TS bracket features gauging tabs and recessed nailing spurs, for wood or metal studs. Acceptable for use in 2-hour fire rated walls and ceilings. 1-1/2" deep - 15.5 cubic inches. UL Listed. UPC bar code.
Hubbell 518 Gangable Switch Box Thomas & Betts B232B-UPC Outlet Box Gardner Bender PSW Cable Staple
One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage.
Gardner Bender PSB Low Voltage Cable Staple Gardner Bender PDS Low Voltage Cable Staple Raco 223 Electrical Box
For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. UV resistant polyethylene saddles, zinc plated nails. Used for inside and outside applications. Clip-on feature enables hands-free installation. Secures multiple RG-59, RG-59. Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed.
Carlon Super Blue BH118R Old Work Outlet Box Gardner Bender PSW Low Voltage Cable Staple AmerTac Zenith VM1020NAW Coaxial Staple
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed. For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage. Attaches coax cable to a wall. .5" height x .25" width x .25" depth.
Raco 529 Gangable Switch Box Carlon A122 ENT Flexible Raceway Outlet Box Raco 545 Non-Gangable Old Work Switch Box
Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth. Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 8211 Outlet Box Allied Moulded 2300-NK Switch Box Gardner Bender GSE-310 Service Entrance Staple
Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed. Secures service entrance cable. Pointed offset legs drive in straight, will not split wood. High quality carbon steel for durability and easy nailing.
STAPLE PLAS MASONRY CLIP 1/2IN King 70112 Insulated Cable Staple Raco 508 Non-Gangable Switch Box
Secures Romex, UF and other type-NM cable. Hardened nails can penetrate cement block, mortar or plaster surfaces. Smooth saddle prevents damage to cable insulation. Made of 12 gauge carbon steel, insulated with high-impact, hot-melt PVC bonded to the top of the staple, tumble deburred and with rust inhibitor applied. Reduces risk of electrical fire and prevents a short circuit if the insulation is cut. Color coded for size and application and highly visible. Used with BX or Romex 3 conductor, #14, #12, and #10 WG or 2 stacked oval Romex #14 and #12 WG. Rated for up to 2500 volt. Dielectric rating per ETL Test 525777. Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed.
Hubbell 8257 Welded Outlet Box Raco 487 Gangable Old Work Switch Box Raco 8601 Gangable Switch Box
Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed.
Thomas & Betts B708-SHK Ceiling Pan Box Raco TigerGrip 523 Gangable Old Work Switch Box Carlon B620HG-UPC Ceiling Box
Shallow ceiling fan outlet box with mounting screws. 1 integral clamp. Non-conductive high impact lightweight PVC. 5 knock outs, 8 cubic inch capacity. For new work or renovations. Mounts ceiling fan securely to the ceiling joist. Rated for fans up to 35 pounds and fixture up to 50 pounds. 4" diameter x 5/8" depth. UL Listed. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded. Non-metallic sheathed cable clamps. Ceiling box with 14 -1/4" - 23-1/2" adjustable bar hanger. Fixture spacing for 2-3/4" and 3-1/2". 4" diameter x 2-1/4" depth. Ground lug and screw. 6 integral clamps. Listed for fixture support up to 50 lb. UL Listed, meets NEMA OS-2.
Carlon Super Blue BH234R Old Work Outlet Box Thomas & Betts B355R Outlet Box Gardner Bender PMW Low Voltage Cable Staple
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed. Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed. For securing speaker, telephone, bell and other low-volt wire. Polyethylene saddle won't rust, rot or deteriorate. Zinc-plated nail resists rust and corrosion. 1 nail per staple. Dives in with a hammer. UL Listed.
Omnifilter RS14 Water Filter Cartridge Raco 2011FBAR Vapor Barrier Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box
Poly spun cartridge for whole house water filters U25, OB1, and OB5 series. 10 micron rating. 60 days/10,000 gallon life capacity. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings.
Raco 8235 Electrical Box Raco 295 Ceiling Fan Box GB-Gardner Bender MSI-75 Cable Staples
Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed. Ceiling fan 4" round pan, 1/2" deep, 6 cubic inches, 5 bottom 1/2" knockouts. Used for new work and renovations. Ceiling fan rated, used in the installation of heavy light fixtures or ceiling fans. Maximum 70 pound fan or 150 pound fixture. Includes nonmetallic sheathed cable connector, mounting hardware, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Use on NM, BX, UF and other electrical cables. Made from high carbon steel. Cable protected by polyethylene insulation.
Powerzone OR670612 SPT-2 Extension Cord Powerzone OR660612 SPT-2 Extension Cord Raco 605 Gangable Switch Box
Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only. Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed.
Gardner Bender PS-150Z Insulated Cable Staple Coleman 2235 SPT-2 Extension Cord Carlon B455A-UPC Outlet Box
For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Indoor only, household cord. Thin male plug keeps cord close to wall. Plug does not block other outlets. 13 amp/125 volt. UL Listed. Sleeved. Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5".
Gardner Bender PS-150 Insulated Cable Staple Carlon Super Blue BH525H Ceiling Box Gardner Bender GSE-410 Service Entrance Staple
For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. 4" diameter x 2.95" depth. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and clamps to make installation faster. Listed for fixture support up to 50 lb. Hanger bar adjusts from 11-1/2" to 18-1/2". UL Listed. Secures service entrance cable. Pointed offset legs drive in straight, will not split wood. High quality carbon steel for durability and easy nailing.
Gardner Bender PS-175ZN Insulated Cable Staple Star Rite OK25 Replacement Filter Housing O-Ring Sta-Rite RS12 Omnifilter Water Filter Cartridges
For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. For use with No.U25 Omni whole house water filter. String wound cartridge for whole hose water filters U25, OB1, and OB5 series. 20 micron rating. 30-day/5,000 gallon life capacity.
Raco Romex 176 Electrical Box Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box Raco 8265 Ceiling Outlet Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed.
Sta-Rite K4-M6-S06 O-ring Powerzone OR670615 SPT-2 Extension Cord Powerzone OR780615 SPT-2 Extension Cord
For use with Omni whole house filters Nos.OB1, OB5, R12, and R14; and Omni under-sink water filters Nos.CBF20, SFM2, UC2. CBF1, CBF3, OT32, OB3, and RO2000. Will also fit Nos.BC1, TC3, UC2, U400. U500, U600, U700, Omni Super, and Total 2. If your unit uses blue o-ring, replaces Total Plus, Omni Regular and Omni Deluxe o-rings. Bagged. Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only. Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only.
Powerzone OR660615 SPT-2 Extension Cord Thomas & Betts B234ADJ Wall Box GB PSW-160 Low Voltage Cable Staple
Three polarized outlets in a solid molded plug for convenient use indoors. Includes an attached safety cover for unused outlets. 13 amp/125 volt/1625 watts. UL, cULus Listed for indoor use only. Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. GB Cable Staple, Low Voltage, 3/16 in Crown, Polyethylene, Zinc Plated, White, For Inside and Outside Applications
Thomas & Betts B720R-SHK Ceiling Fan Box Thomas & Betts BH464A Rigid Outlet Box Saf-T-Cap 0105000 Outlet Ceiling Fan Box
Non-conductive high impact lightweight PVC. Full 20 cubic inch capacity. 6 integral clamps. 4" diameter x 2-1/4" depth. Used for new work or renovations. Rated for fans up to 35 pounds and fixture up to 50 pounds. Mounts fan to a cross member secured between ceiling joist. Mounting screws included. UL Listed. Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. For new construction or applications where attic is accessible. Fits all ceiling fans. Maximum load rating for ceiling fans is 70 pounds. 100 pounds for fixtures. 8-32 threads for lightweight fixtures, 10-24 threads for ceiling fans. 3 knockouts for conduit or Romex. 2 Romex clamps. 1-1/2" deep, 15.5 cubic inch capacity. Includes SAF-T-CAP and mounting screws. UL Listed.
Allied Moulded 9312-EWK Old Work Outlet Box Powerzone OR920607 SPT-2 Extension Cord Gardner Bender PSB Low Voltage Cable Staple
Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed. Ultra thin 1/2" thick plug converts one outlet into three. Includes safety covers for unused outlets. UL, cULus Listed for indoor use only. For metallic and non-metallic cording and cable. Constructed of high-grade injection molded polyethylene cradles and zinc-plated nails. Provides toughness, high dielectric strength and longevity. Smooth saddles hold wire securely while preventing damage.
Carlon Super Blue BH525HP Ceiling Box Allied Moulded 3300-NK Outlet Box Gardner Bender PEC-31525 Coaxial Cable Clamp
Ceiling box with hanger bar, adjusts from 11-1/2" to 18-1/2". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Listed for fixture support up to 50 lb. 4" diameter x 3" depth. UL Listed. Ground lug included. Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed. Secures RG-59, RG-6 coaxial. Combo screw for safer installs. Screw-in depth of 1/2".
Sta-Rite OW30-S6-S06 Tank Wrench GB PSR-25 Low Voltage Coaxial Roofing Staple Coleman 0814 SPT-2 3-Outlet Power Tap Extension Cord
For use with Omnir filters Nos. CBF1, SFM2, USF1,  CBF3, USF3, SFM2, USM2, OCT2, US30, US32, RO2050, and RO2000. Carded. GB Coaxial Roofing Staple, Low Voltage, 1/4 in Crown, Plastic, Black, Suitable For Use With: RG-59 and RG-6 Coaxial Cable into Roofing Shingles, For Inside and Outside Applications Solid molded power taps, the convenience of 3 outlets in a compact design. Sleeved.
Culligan OR-100 Water Filter Accessories Raco 8325 Ceiling Outlet Box Tiger Grip 517 Gangable Switch Box
Use on comparable sized filter housing. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 pound maximum recommended support load. Furnished with 3/8"-18 NPS trade size fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. 1-1/2" deep - 15.5 cubic inches. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed.
Culligan 01019187 Water Filter Accessories Gardner Bender MS-500J Cable Staple Culligan SW-2A Water Filter Accessories
Single housing bracket is a "U" shaped mounting bracket for 3/4" inlet/outlet standard whole house housings. The UB-1 mounts standard whole house water filter housings and helps support the weight of the water filter. Screws are included with the UB-1 mounting bracket for securing the water filter housing to the wall. Use with: Culligan HF-150 (883.4442) and Culligan HF-360 (306.9820) Water Filter Housings. Two-wire staples fasten 2 and 3 conductor non-metallic cable. SIZE: 1/2" x 1" - For 2 conductor (No. 12 and No. 14) NM cable. SIZE: 9/16" x 1-1/4" - For 3 conductor (No. 10 and No. 12) NM, BX, UF and other cable. Use on comparable sized filter housing to replace filter cartridge.
Raco 680 Switch Box Culligan SW-1 Small Filter Housing Wrench Raco 681 Switch Box
Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Use on comparable sized filter housing to replace filter cartridge. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Gardner Bender PS-175 Insulated Cable Staple Carlon B468R Old Work Outlet Box Raco 8326 Ceiling Outlet Box
For metallic and non-metallic cording and cable. Easy to install; drive both zinc plated nails together without splitting wood. Recessed nail heads for minimum exposure. Smooth saddle (3/8" width) prevents damage to insulation. High grade, injection molded polypropylene resists rot, rust, deterioration and effects of extreme temperature; non-conductive for safe and secure cable fastening. Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 lb. maximum recommended support load. Furnished with 3/8"-18 NPS fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Thomas & Betts BH525L Ceiling Fan Box Raco 8240 Electrical Box Raco 685 Switch Box
New work ceiling fan box with nails and metal brace for stud finishing. Rated for fans up to 35 pounds and fixtures up to 50 pounds. 4.062" diameter x 3.06" depth. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wire capacity, and comes with molded-in nailing flanges. UL Listed. Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed.
Coleman 2236 SPT-2 Extension Cord Coleman 2239 SPT-2 Extension Cord Raco 2027-FBAR Round Vapor Barrier Box
Indoor only, household cord. Thin male plug keeps cord close to wall. Plug does not block other outlets. 13 amp/125 volt. UL Listed. Sleeved. Indoor only, household cord. Thin male plug keeps cord close to wall. Plug does not block other outlets. 13 amp/125 volt. UL Listed. Sleeved. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, 4" round flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Used independently of vapor barrier hats.
Hubbell 683 Switch Box Raco 2002FBAR Vapor Barrier Box Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box
Drawn construction for surface mount applications. Conduit wiring system. Eight 1/2" and four 3/4" conduit knockouts (sides). Three 1/2" and two 3/4" conduit knockouts (bottom). 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed.
Raco 7120 Ceiling Fan Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box Raco 296 Ceiling Fan Box