Home > ELECTRICAL > SPECIALTY ELECTRICAL > ELECTRONICS > REMOTE CONTROLS
Choose a sub category:
WIRENUTS / CONNECTORS TERMINAL LUGS ELECTRICAL TAPE/DUCT SEAL
WIRE TERMINAL ENDS TUBING & WRAPS ANTI-OXIDANTS
SPLIT BOLT CONNECTORS SPLICER / REDUCERS CABLE STAPLES
CABLE TIES WIRE CLAMPS/CLIPS GLUES / CEMENTS
WIRE MANAGEMENT KITS ELECTRICAL BUSHINGS ELECTRICAL GROMMETS
MISC WIRING CONNECTORS
Sort By:
1
Halex 90211 Compression Connector Bell Raco 5173-2 Blank Weatherproof Device Cover Bell Raco 5173-1 Blank Weatherproof Device Cover
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated.
Halex 90221 Concrete Tight Compression Coupling Halex 90212 Concrete Tight Rain Tight Compression Connector Bell Raco 5173-7 Blank Weatherproof Device Cover
Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated.
Hubbell 5173-5 Blank Weatherproof Cover Hubbell 5173-6 Blank Weatherproof Cover Halex 90222 Concrete Tight Compression Coupling
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved.
Worldwide Sourcing PMB-001-3L Tissue Roller ROD HOLDER TOILET PAPER WHITE Mintcraft LBE02002-51-07 Tissue Rollers
Homebasix Toilet Paper Roller, Plastic, White Spring loaded, fits most toilet brackets, white finish. Mintcraft Toilet Paper Roller, Plastic, White
Halex 02110 Compression Connector Halex 90401 Offset Nipple Hubbell 5374-0 Blank Round Flat Weatherproof Cover
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. For use with 4" round splice boxes. Installation hardware, and gasket included. 4" diameter, shrink wrapped. UL Listed.
Halex 02210 Concrete Tight Compression Coupling Bell Raco 5175-1 Blank Weatherproof Device Cover Plumb Pak PP23535 Adjustable Toilet Paper Roller
Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". 3/8" ends.
Plumb Pak PP835-35 Adjustable Toilet Paper Roller Mintcraft CSC3L003 Tissue Rollers Halex 02905B Compression Conduit Elbow
3/8" ends. Mintcraft Toilet Paper Roller, Chrome Zinc die cast. Concrete-tight. Indoor or outdoor applications. Use to connect EMT conduit to a metal outlet box or enclosure where a 90 degree bend is required and a pipe bending tool is not used. UL, CSA Listed.
Decko 38040 Toothbrush and Tumbler Holder ROD HOLDER TOILET PAPER CHROME Arrow Hart S2962 Weatherproof Cover
Scratch and rust resistant. Easy to install. Hardware included. Chrome plated for durability. Spring-loaded replacement for toilet paper roller. Tough plastic construction, resistant to high impact and sunlight. Non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Self closing cover. Vertical only. UL Listed for wet locations with cover closed.
Hubbell 5175-5 Blank Weatherproof Cover Halex 90402 Offset Nipple Hubbell 5180-0 Weatherproof Device Cover
For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
Plumb Pak PP836-44 Adjustable Toilet Paper Roller Hubbell 5180-6 Weatherproof Device Cover Decko 38090 Toilet Tissue Holder
Plumb Pak Toilet Paper Roller, Adjustable, Chrome Plated, 3/8 in Roller Ends Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Chrome plated for durability. Scratch and rust resistant. Plastic roller. Easy to install. Hardware included.
Bell Raco 5175-0 Blank Weatherproof Device Cover Decko 38890 Toilet Tissue Holder Halex 02112 Compression Connector
For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". Chrome plated for durability. Scratch and rust resistant. Plastic roller. Easy to install. Hardware included. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved.
Hubbell 5320-0 Outlet Box Bell Raco 5320-1 Weatherproof Box Halex 90292 Concrete Tight Compression Short Radius Conduit Elbow
For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Zinc die cast. Concrete-tight. Indoor or outdoor applications. Use to connect EMT conduit to a metal outlet box or enclosure where a 90 degree bend is required and a pipe bending tool is not used. UL, CSA Listed.
Halex 90291 Concrete Tight Compression Short Radius Conduit Elbow Mintcraft BE02006-07-SOU Tissue Roller Bell Raco 5180-1 2-Hole Weatherproof Device Cover
Zinc die cast. Concrete-tight. Indoor or outdoor applications. Use to connect EMT conduit to a metal outlet box or enclosure where a 90 degree bend is required and a pipe bending tool is not used. UL, CSA Listed. Mintcraft Toilet Paper Roller, Brushed Nickel Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
Bell Raco 5180-2 2-Hole Weatherproof Device Cover Hubbell 5180-5 Weatherproof Device Cover Bell Raco 5180-7 2-Hole Weatherproof Device Cover
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
Mintcraft BE02006-35-07-SOU Tissue Roller Halex 02212 Concrete Tight Compression Coupling Cooper 7500-Box Decorative Standard Rocker Switch
Mintcraft Toilet Paper Roller, Venetian Bronze Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved. Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements.
Cooper 7500-Box Decorative Standard Rocker Switch Bell Raco 5152-0 Weatherproof Device Cover Hubbell 5320-6 Outlet Box
Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Installation hardware, gasket, multi-lingual instructions included. For single 1.406" diameter receptacle. UL Listed for wet location with cover closed. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Hubbell 5155-5 Single Device Cover Bell Raco 5155-6 Round Opening Weatherproof Device Cover Bell Raco 5406-0 Weatherproof Extension Box
With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated. With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated. Used to provide additional capacity. Die cast aluminum construction. Installation hardware, gasket, and ground screw provided. 9.5 cubic inch capacity. 4-1/2" x 2-3/4" x 1" deep. UL Listed, CSA, NEMA 3R Rated.
Bell Raco 5320-2 Weatherproof Box Arrow Hart S1962W-SP Weatherproof Cover Arrow Hart S1961 Weatherproof Cover
For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2". Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations.
Arrow Hart S1962 Utility Halogen Low Profile Weatherproof Cover Arrow Hart S1961W-SP Weatherproof Cover GB-Gardner Bender GSW-24 Canopy Switches
Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2". Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations. Maintained contact switch family utilized in applications requiring continuous continuity contacts. Number 18 AWG, 6" stripped wire leads. Mounting nut included.
Hubbell 5324-0 Outlet Box Cooper C1303-7V Framed Grounded Toggle Switch Cooper 1301-7 Framed Grounded Toggle Switch
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Three threaded 3/4" outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed.
Gardner Bender GSW Standard Toggle Switch Gardner Bender GSW Standard Toggle Switch Halex 02115 Compression Connector
Medium-duty bat handle-screw type terminal. 6" wire leads. Smaller toggle switch for limited space applications. Frame and support are steel with zinc chromate. On/off sequence, has an on/off faceplate. Heavy-duty terminal. On-Off operation. Motor rated. 20 amp at 125 volts AC, 10 amp at 277 volts AC. 1/2" mounting hole. UL Listed. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved.
Halex 20210 Concrete Tight Compression Connector Hubbell 5321-0 Outlet Box Gardner Bender GSW-32 Pull Chain Switch
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Mounts in 13/32" diameter hole. Two position, 2 wire. (GSW-35 mounts in 1/2" diameter hole). number 18 AWG, 6" stripped wire leads.
GB-Gardner Bender GSW-25 Canopy Switches Bell Raco 5103-0 1-Hole Weatherproof Device Cover Bell Raco 5103-1 1-Hole Weatherproof Device Cover
GFCI VERT 1G COVER GRAY
Our Price: $4.88
Maintained contact switch family utilized in applications requiring continuous continuity contacts. Number 18 AWG, 6" stripped wire leads. Mounting nut included. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped.
Bell Raco 5103-2 1-Hole Weatherproof Device Cover Bell Raco 5320-7 Weatherproof Outlet Box Bell Raco 5320-5 Outlet Box
Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Carlon E98TSCN-CAR Weatherproof Device Cover Bell Raco 5146-0 1-Hole Weatherproof Device Cover Jandorf 61224 Single Circuit Push Button Switch
Weatherproof cover for single toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified. Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated. Jandorf Push Button Switch, Single Circuit, Series: 61224, 125 V, 1 A, 1 Poles, Contact Configuration: SPST, On/Off, 2-Wire Terminal, Brass, UL Listed, Brass Canopy
Jandorf 61155 Toggle Switch Nut Gardner Bender GSW-12 Toggle Switch Gardner Bender GSW-120 Toggle Switch
Thread size M12x1-6H. Thickness 2.5mm O.D. 14mm. Heavy-duty screw type terminal. Brass terminals, frame and support are steel with zinc chromate, case is black phenolic plastic, external parts are brass/bright nickel. Motor rated. Heavy-duty spade type terminal. Versatile toggle switch family with multiple position configurations. Ideal for industrial equipment, automotive or emergency lighting. 1/2" mounting hole required. All switches must be installed with a hex nut (provided) behind panel to prevent damage during installation.
GB-Gardner Bender GSW-20 Toggle Switch Covers GB-Gardner Bender GSW-39 Canopy Switches GB-Gardner Bender GSW-22 Momentary Switches
Tough EDPM rubber covers protects switches from moisture, dust and dirt. Built-in hex nut base screws onto all GB toggle switches. Momentary action. Variable speed and two-circuit brass plated pull chain switches for multifunction applications. Push-in connections for #18 AWG wire. Recommended mounting hole .406 diameter. 4 position 3 wire. Wire lead terminal type. Basic pushbutton screw type terminal switch family utilized in applications requiring intermittent continuity contacts. Mounts in standard 1/2" diameter hole. Mounting nut included. () Indicates momentary action.
Carlon E98DHGN-CAR Weatherproof Cover Hubbell 5101-6 Weatherproof Device Cover Jandorf 61202 Canopy Switch
Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. Jandorf Pull Chain Switch, 2-Speed, 125 V, 3 A, 1 Poles, 2 Circuits, Off/On/On, 3-Push Terminal, Brass, Standards: UL Listed
Jandorf 61157 Toggle Switch Plate Gardner Bender GSW Toggle Switch Hubbell 5121-5 Weatherproof Device Cover
On/off markings. Heavy-duty, screw type terminal. Double insulated for moisture protection in all environments. Internal "O" ring design for moisture and dust resistance. Perfect for marine/recreational equipment and weather resistant applications. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated.
Bell Raco 5321-2 Weatherproof Box Bell Raco 5321-1 Weatherproof Box Gardner Bender GSW Toggle Switch
Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Medium-duty bat handle-screw type terminal. S.P.S.T. smaller constructed toggle switches for limited space applications. Frame and support are steel with zinc chromate. Brass terminals. On/Off sequence also has an On/Off faceplate.
Gardner Bender GSW Toggle Switch Arrow Hart CSB GRD Pro Toggle Switch Arrow Hart CSB GRD Pro Toggle Switch
Heavy-duty terminal. On-Off operation. Motor rated. 20 amp at 125 volts AC, 10 amp at 277 volts AC. 1/2" mounting hole. UL Listed. Small toggle switch blends with standard grade toggles. Larger contacts, backwire clamps on the side terminals. Side wire terminals accept up to number 10 solid wire. Back wire terminal accepts 12 or 14 gauge wire. Heavy duty cam action mechanism. Long, broad steel mounting strap, zinc-plated for corrosion resistance. Built-in wire stripper for number 12 and number 14 wire. Ground screw terminal, stippled line and ground contacts standard. Tri-Combo head mounting and terminal screws. 15 amp, 120/277 volt. cULus Listed, NOM certified. Small toggle switch blends with standard grade toggles. Larger contacts, backwire clamps on the side terminals. Side wire terminals accept up to number 10 solid wire. Back wire terminal accepts 12 or 14 gauge wire. Heavy duty cam action mechanism. Long, broad steel mounting strap, zinc-plated for corrosion resistance. Built-in wire stripper for number 12 and number 14 wire. Ground screw terminal, stippled line and ground contacts standard. Tri-Combo head mounting and terminal screws. 15 amp, 120/277 volt. cULus Listed, NOM certified.
Bell Raco 5146-5 Weatherproof Device Cover Halex 02120 Compression Connector Bell Raco 5322-0 Weatherproof Box
Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated. Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Weatherproof box, with lugs. Five 1/2" threaded outlets. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth x 4-1/2" length x 2-3/4" width. 18.3 cubic inch capacity. UL Listed. CSA 22.2 No. 18 NEMA 3R Rated.
Halex 02215 Concrete Tight Compression Coupling Bell Raco 5321-5 Weatherproof Outlet Box Hubbell 5361-0 Splice Box
Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed.
Gardner Bender GSW Canopy Toggle Switch GB-Gardner Bender GSW-21 Canopy Switches Mintcraft L760-26-03 Freedom Collection Towel Ring
Plastic case and switch. Heavy-duty spade type terminal. Double insulated for moisture protection in all environments, internal "O" ring design for moisture and dust resistance. Momentary contact in either direction. Use for marine/recreational equipment or any weather-resistant application. UL/CSA Rated. Maintained pushbutton switch. Push On-Push Off. #18 AWG, 6' stripped wire leads. Mounting nut included. Zinc alloy, with aluminum ring. Bagged.
Bell Raco 5101-2 1-Hole Weatherproof Device Cover Bell Raco 5101-1 1-Hole Weatherproof Device Cover Bell Raco 5101-0 1-Hole Weatherproof Device Cover
For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Spot-Gro 5330-0 Weatherproof Box Bell Raco 5324-5 Outlet Box Bell Raco 5121-1 Weatherproof Switch Cover
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Powder coat finish. 16.5 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. Shrink wrapped. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Three threaded 3/4" outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated.
Gardner Bender GSW-23 Push Button Switch Hubbell 5101-5 Weatherproof Device Cover Bell Raco 5101-7 1-Hole Weatherproof Device Cover
Basic pushbutton screw type terminal switch family utilized in applications requiring intermittent continuity contacts. Mounts in standard 1/2" diameter hole. Mounting nut included. () Indicates momentary action. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Jandorf 61149 Double Circuit Toggle Switch Legrand Despard ACD3I Special Purpose Toggle Switch Carlon E98GFCN-CAR Weatherproof Device Cover
Jandorf Toggle Switch, Double Circuit, Series: 61149, 120 V, 10 A, On/Off, Contact Configuration: SPST, 1 Poles, 2-Screw Terminal, UL Listed Older style device with a rounded shape that is slightly flattened top and bottom. Flexible, smaller than a standard device, fits in a smaller opening. Used in locations with limited space or restricted options. UL Listed, conforms to NEMA specifications. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. 2.63" high x 1.31" wide opening.
Carlon E98SSCN-CAR Weatherproof Cover Carlon E98GDRN-CAR Weatherproof Device Cover Thomas & Betts E381DR Type T Weatherproof Switch Box
Non-conductive. Suitable for wet locations. Gaskets and screws included. UL Listed. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. Weatherproof, for use with nonmetalic wiring systems. Nonconductive, noncorrosive, and impact resistant for a safe, long, service-free life in exposed applications. Install in accordance with NEC and local codes. Three 1/2" threaded ports, one on each end and one in the back. UL Listed.
Jandorf 61200 Canopy Switch Jandorf 61208 Canopy Switch Carlon E98G5FN-CAR Weatherproof Cover
Jandorf Pull Chain Switch, 125 V, 3 A, 2 Poles, 4 Positions, 2 Circuits, Off/L1/L2/L1-2, 3-Wire Terminal, Brass, Standards: UL Listed Jandorf Pull Chain Switch, 125 V, 3 A, 1 Poles, 1 Circuits, On-Off, 2-Wire Terminal, Nickel, Standards: UL Listed For 50 amp twist lock single receptacles under 2.250" diameter. For exposed applications. Will not rust or corrode. Gaskets and screws included. UL Listed.
Arrow Hart CS Compact Toggle Switch Arrow Hart CS Grounded Compact Toggle Switch Arrow Hart CS Grounded Compact Toggle Switch
Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896.
Hubbell 5361-6 Splice Box Gardner Bender GSW-34 3-Speed Pull Chain Switch Halex 20221 Concrete Tight Compression Coupling
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Variable speed and two-circuit brass plated pull chain switches for multifunction applications. Push-in connections for #18 AWG wire. Mounts in 13/32" diameter hole. Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved.
Gardner Bender Professional GSW-14 Toggle Switch Arrow Hart S3966W-SP Decorative Weatherproof Cover Arrow Hart S2966W-SP Decorative Weatherproof Cover
Heavy-duty screw type terminal. Versatile toggle switch family with multiple position configurations. Ideal for industrial equipment, automotive or emergency lighting. 1/2" mounting hole required. All switches must be installed with a hex nut (provided) behind panel to prevent damage during installation. For GFCI/Decorator receptacle used in wet locations. Gaskets provided to seal cover edges as well as device openings. Stainless steel mounting screws included. Horizontal flush or surface mount. UL Listed. Plastic, impact and sunlight resistant. Gaskets provided to seal cover edges as well as device openings. Self closing cover. Stainless steel mounting screws furnished. Vertical, flush or surface mount. UL Listed.
Arrow Hart S2966 Decorative Weatherproof Cover Arrow Hart S3966 Decorative Weatherproof Cover RECPTCL/CVR DPLX HRZ WP GRY 1G
Plastic, impact and sunlight resistant. Gaskets provided to seal cover edges as well as device openings. Self closing cover. Stainless steel mounting screws furnished. Vertical, flush or surface mount. UL Listed. For GFCI/Decorator receptacle used in wet locations. Gaskets provided to seal cover edges as well as device openings. Stainless steel mounting screws included. Horizontal flush or surface mount. UL Listed. Used where weatherproof protection is required for an outdoor receptacle. Self-closing lids. Powder coat finish. Size 4-1/2" width x 2-3/4" length. Includes gasket and mounting hardware. UL Listed, NEMA 3R Rated.
Carlon E98SRCN-CAR Weatherproof Cover Bell Raco 5331-0 Weatherproof Box Jandorf 61166 Single Circuit Toggle Switch
For 15 amp or other single receptacles under 1.375" diameter. Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Five 3/4" threaded outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed, CSA Approved and NEMA 3R Rated. Jandorf Toggle Switch, Single Circuit, Series: 61166, 125 V, 10 A, On/Off/On, Contact Configuration: SPDT, 1 Poles, 3-Screw Terminal, UL Listed
Halex 20212 Concrete Tight Compression Connector Gardner Bender Professional GSW-16 Toggle Switch Halex 02220 Concrete Tight Compression Coupling
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Heavy-duty screw type terminal. Versatile toggle switch family with multiple position configurations. Ideal for industrial equipment, automotive or emergency lighting. 1/2" mounting hole required. All switches must be installed with a hex nut (provided) behind panel to prevent damage during installation. Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved.
Mintcraft CSC 8534-3L Manhattan  Toothbrush/Tumbler Holders Bell Raco 5141-0 Weatherproof Switch Cover Mintcraft L3657C-51-07 Manhattan
MintCraft Toothbrush/Tumbler Holder, Series: Manhattan Collection, Rectangular Shape, Concealed Screw Mounting, Chrome Weatherproof protection for an "on-off" type switch. Vertical, mounted to device. Rugged die cast construction, powder coat finish. Self-closing lid assures weatherproof protection when not in use. Supplied with a switch - no need to purchase separate components. Switch is unassembled to the cover. UL, CSA and NEMA 3R rated. Shrink wrapped. MintCraft Toothbrush/Tumbler Holder, Series: Manhattan Collection, Rectangular Shape, Concealed Screw, Wall Mounting, White
Mintcraft 3657C-07-SOU Toothbrush/Tumbler Holders Hubbell 5323-0 Outlet Box Core Aspire 9503DS Rocker Switch
MintCraft Toothbrush/Tumbler Holder, Rectangular Shape, 4.6 in Length, 1.9 in Width, 3.4 in Height, Bronze, Brushed Nickel With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCIs. 5 reinforced 1/2" threaded connector outlets. Powder coat finish. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. 2" depth x 4-1/2" length x 2-3/4" width. 18.3 cubic inch capacity. UL Listed. Curved profile rocker, accented by the color and texture of its surrounding frame, with two-tone elegance. Virtually unbreakable, ultrasonically welded top and backbody; extra-long, extra-wide mounting straps; #14 push-in terminals; backwire clamps on side terminals; easy-access ground screws and built-in wire strippers. 15 amp, 120/277 volt.
Jandorf 61028 Plunger Single Circuit Push Button Switch Gardner Bender GSW Toggle Switch Mintcraft 3657C-35-07-SOU Toothbrush/Tumbler Holder
Jandorf Push Button Switch, Plunger Single Circuit, Series: 61028, 125 V, 2 A, 1 Poles, Contact Configuration: SPST, Normally OFF, Momentary Snap Operation, Round Shape, 2-Tab Terminal, UL Listed Heavy-duty screw type terminal. Versatile toggle switch family with multiple position configurations. Ideal for industrial equipment, automotive or emergency lighting. 1/2" mounting hole required. All switches must be installed with a hex nut (provided) behind panel to prevent damage during installation. MintCraft Toothbrush/Tumbler Holder, Rectangular Shape, 4.6 in Length, 1.9 in Width, 3.4 in Height, Venetian Bronze
Bell Raco 5361-2 Splice Box Bell Raco 5361-1 Single Ended Splice Box Jandorf 61132 Double Circuit Toggle Switch
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Jandorf Toggle Switch, Double Circuit, Series: 61132, 125 V, 10 A, On/Off, Contact Configuration: SPST, 1 Poles, 2-Screw Terminal, UL Listed
Core Aspire 9503SG Rocker Switch Core Aspire 9503WS Rocker Switch Mintcraft 3660-07-SOU Towel Ring
Curved profile rocker, accented by the color and texture of its surrounding frame, with two-tone elegance. Virtually unbreakable, ultrasonically welded top and backbody; extra-long, extra-wide mounting straps; #14 push-in terminals; backwire clamps on side terminals; easy-access ground screws and built-in wire strippers. 15 amp, 120/277 volt. Curved profile rocker, accented by the color and texture of its surrounding frame, with two-tone elegance. Virtually unbreakable, ultrasonically welded top and backbody; extra-long, extra-wide mounting straps; #14 push-in terminals; backwire clamps on side terminals; easy-access ground screws and built-in wire strippers. 15 amp, 120/277 volt. Mintcraft Towel Ring, Brushed Nickel
Arrow Hart S992 Weatherproof Cover Bell Raco 5141-5 3-Way Weatherproof Cover Jandorf 61156 Toggle Switch Plate
For single devices, take either single receptacle or switch. Corrosion resistant materials suitable for exposure to weather. Gaskets provided to seal cover edges and openings. Mount on flush or surface single gang boxes. Gray color. UL Listed. Polybagged. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. On/off markings.
Jandorf 61212 Single Circuit Push Button Switch Jandorf 61140 Single Circuit Toggle Switch Bell Raco 5361-7 Splice Box
Jandorf Push Button Switch, Single Circuit, Series: 61212, 125 V, 3 A, 1 Poles, Contact Configuration: SPST, On/Off, NIC Operation, 2-Wire Terminal, Nickel Plated, UL Listed Jandorf Toggle Switch, Single Circuit, Series: 61140, 125 V, 15 A, On/Off/On, Contact Configuration: SPDT, 1 Poles, 3-Tab Terminal, UL Listed For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed.
Raco 5372-0 Weatherproof Splice Box Hubbell 5361-5 Splice Box Mintcraft 3660-35-07-SOU Towel Ring
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 4" diameter x 1-1/2" depth. UL Listed. NEMA 3R Rated. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Mintcraft Towel Ring, Venetian Bronze
Jandorf 61018 Snap-In Toggle Switch Jandorf 61148 Double Circuit Toggle Switch Halex 20222 Concrete Tight Compression Coupling
Jandorf Toggle Switch, Snap-In, Series: 61018, 125 V, 10 A, On/Off, Contact Configuration: SPST, 1 Poles, 2 Positions, 2-Screw Terminal, White, UL Listed Jandorf Toggle Switch, Series: 61148, 125 V, 10 A, On/Off, Contact Configuration: SPST, 1 Poles, 2-Tab Terminal, Double Insulation, UL Listed Use to join two lengths of EMT conduit together. Zinc. UL, CSA Approved.
Jandorf 61135 Double Circuit Toggle Switch Carlon E9G2SSNR Weatherproof Cover Mintcraft L3660-51-07 Manhattan
Jandorf Toggle Switch, Double Circuit, Series: 61135, 125 V, 4 A, On/Off, Contact Configuration: SPST, 1 Poles, 2-Wire Terminal, UL Listed Weather resistant cover for double toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified. Mintcraft Towel Ring, Series: Manhattan Collection, Concealed Screw Mounting, Aluminum, White Coral
Carlon Code Keeper Red Dot CKNM-NG Weatherproof Cover Arrow Hart S989-SP Weatherproof Cover Jandorf 61306 Double Circuit Push Button Switch
Accepts GFCI, duplex, switch and up to 1-3/8" round devices. Nonconductive, noncorrosive, and impact resistant. Won't rust or fade. Scratch resistant. For use in wet/damp locations. Keyhole mounts, loosen the existing device screws and slide the cover over. Comes with adapter plates and pre-adhered gaskets. Wasp guard included to keep out unwanted pests. Lockable for security. UL Listed. Corrosion resistant materials suitable for exposure to weather. Gaskets provided to seal cover edges and openings. Corrosion resistant mounting screws included. Mount on flush or surface single gang boxes. UL Listed. Jandorf Push Button Switch, Double Circuit, Series: 61306, 120 V, 3 A, 1 Poles, Contact Configuration: SPST, Normally Off, Momentary Operation, 2-Screw Terminal, UL Listed, Black Canopy
Thomas & Betts E365DR Type T Switch Box Arrow Hart Eagle CS Toggle Switch Arrow Hart CS Compact Toggle Switch
Nonmetallic threaded switch box with five 1/2" threaded holes, for exposed applications with nonmetallic wiring systems only. Mounting feet included. 4" diameter. 13.5 cubic inch capacity. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. .050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. 20 amp, 120/277 volt. Meets all UL 20 requirements, Federal Specifications WS 896. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. .050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. 20 amp, 120/277 volt. Meets all UL 20 requirements, Federal Specifications WS 896.
Arrow Hart CS Compact Toggle Switch GB-Gardner Bender GSW-33 Canopy Switches Bell 5400-0 Extension Adapter
Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. .050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. 20 amp, 120/277 volt. Meets all UL 20 requirements, Federal Specifications WS 896. Variable speed and two-circuit brass plated pull chain switches for multifunction applications. Push-in connections for #18 AWG wire. Mounts in 13/32" diameter hole. Used to provide additional capacity needed for NEC box fill requirements. Die cast aluminum construction. 6 threaded 1/2" outlets. Installation hardware gasket and 1/2" closure plugs included. Ground screw is provided. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded 1/2" fittings and threaded conduit. 5-1/4" length x 3-1/2" width x 1-1/2" depth. UL Listed. NEMA 3R Rated.
Jandorf 61029 Plunger Single Circuit Push Button Switch Bell Rayntite 5034-0 Weatherproof Device Cover Jandorf 61112 Double Circuit Toggle Switch
Jandorf Push Button Switch, Plunger Single Circuit, Series: 61029, 125 V, 0.75 A, 1 Poles, Contact Configuration: SPST, Normally On, Momentary Operation, Round Shape, 2-Tab Terminal, UL Listed For weatherproof 30-50 amp receptacles and wet locations. 2.625" diameter. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when the receptacle is not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL listed 514-A , File E 195978 CSA C22.2 No. 18 NEMA 3R rated. Shrink wrapped. Jandorf Toggle Switch, Double Circuit, Series: 61112, 12 V, 20 A, On/Off, Contact Configuration: SPST, 1 Poles, 2-Tab Terminal, Black, UL Listed
Jandorf 61118 Toggle Switch Cooper 5223-7 Grounded Standard Toggle Switch Cooper 5223-7 Standard Toggle Switch
Jandorf Toggle Switch, Series: 61118, 12 V, 20 A, On/On, Contact Configuration: SPDT, 1 Poles, 3-Tab Terminal, Black, UL Listed Meets all UL 20 requirements. For direct connection to aluminum or copper wire. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Industrial design cam action mechanism insures quiet switch action. Side wire terminals accept up to #10 solid or stranded wire. Terminal screws are backed out-ready for wiring. Combination slot/Phillips head mounting and terminal screws. 15 amp, 120 volt. UL Listed. Meets all UL 20 requirements. For direct connection to aluminum or copper wire. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Industrial design cam action mechanism insures quiet switch action. Side wire terminals accept up to #10 solid or stranded wire. Terminal screws are backed out-ready for wiring. Combination slot/Phillips head mounting and terminal screws. 15 amp, 120 volt. UL Listed.
Jandorf 61221 Single Circuit Push Button Switch Jandorf 61310 Toggle Switch Mintcraft CSC 8586-3L Manhattan
Jandorf Push Button Switch, Single Circuit, Series: 61221, 125 V, 1.5 A, 1 Poles, Contact Configuration: SPST, Normally Off, Momentary Operation, 2-Wire Terminal, UL Listed, For Industrial Controlling Circuits Single pole, single throw, off/terminate. Rated: 21A-14VDC Mintcraft Towel Ring, Series: Manhattan Collection, Sleek Design, Concealed Screw Mounting, Aluminum, Chrome
Jandorf 61168 Ball Double Circuit Toggle Switch Jandorf 61161 Toggle Switch Boot Jandorf 61110 Single Circuit LED Toggle Switch
Jandorf Toggle Switch, Ball Double Circuit, Series: 61168, 125 V, 3 A, On/Off, Contact Configuration: SPST, 1 Poles, 2-Wire Terminal Protects toggle switch. Thread Size 15/32-32NS-2B. Jandorf LED Toggle Switch, Single Circuit, Series: 61110, 12 V, 20 A, Off/On, Contact Configuration: SPST, 1 Poles, 3-Tab Terminal, UL Listed
GB-Gardner Bender GSW-35 Canopy Switches TOGGLE DPDT MOMEN 20A O/OFF/O Arrow Hart TR274 Duplex Combination Switch/Receptacle
Mounts in 13/32" diameter hole. Two position, all angle, 2 wire, mounts in 1/2" diameter hole. #18 AWG, 6" stripped wire leads. Screw terminal, momentary action. (ON)-OFF-(ON). Shutter designed to prevent the insertion of foreign objects. Neon pilot light which is on when switch is on. Switch is horsepower rated for motor loads per UL 20. Thermoplastic toggle, top and backbody. Ultrasonic welding and integrated construction of the strap and body. Tri-combo screw heads. Backwire clamps on side terminals for installation of #12 and #14 AWG wire. Single pole - 15 amp switch, 2-pole, 3-wire tamper resistant receptacle. UL listed, NEMA 5-15.
Cooper 1303-7LT Lighted Grounded Toggle Switch Jandorf 61136 Double Circuit Toggle Switch Hubbell 5148-5 Weatherproof Device Cover
Meets all UL 20 requirements. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14  wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips head mounting and terminal screws. Jandorf Toggle Switch, Double Circuit, Series: 61136, 125 V, 15 A, On/Off/On, Contact Configuration: DPDT, 2 Poles, 6-Screw Terminal, UL Listed Waterproof protection for outside receptacle. Self-closing lids. Installation hardware, gasket, and multi-lingual instructions included. Size: 4-1/2" width x 4-1/2" length. C/UL/US UL 514-A listed, CSA and NEMA 3R rated.
Jandorf 61213 Double Circuit Push Button Switch Bell Rayntite 5030-0 Weatherproof Cover InterDesign Classico Over Tank Tissue Holder
Jandorf Push Button Switch, Double Circuit, Series: 61213, 125 V, 3 A, 1 Poles, 4 Positions, Contact Configuration: 3-Way, Off/On/On/On, 3-Wire Terminal, Brass, UL Listed, L1/L2/L1-2/Off, For Commercial and Industrial For 30-50 amp receptacles, 2.150" diameter. Die cast aluminum construction, powder coat finish. Scratch resistant. Self-closing lid assures protection when not in use. Padlockable. May be mounted to box or device. Includes installation hardware, gasket, and multi-lingual instructions. UL listed NEMA 3R rated. Chrome finish. Increases bathroom storage options limited by pedestal sinks. Rust-resistant chrome. Over the tank design for installation in seconds. Dispenses one roll and stores a second roll.
Bell Raco 5148-0 Weatherproof Device Cover Jandorf 61131 Double Circuit Toggle Switch Jandorf 61036 Single Circuit Push Button Switch
Waterproof protection for outside receptacle. Self-closing lids. Installation hardware, gasket, and multi-lingual instructions included. Size: 4-1/2" width x 4-1/2" length. C/UL/US UL 514-A listed, CSA and NEMA 3R rated. Jandorf Toggle Switch, Double Circuit Heavy Duty, Series: 61131, 125 V, 15 A, On/Off, Contact Configuration: DPST, 2 Poles, 4-Tab Terminal, UL Listed Jandorf Push Button Switch, Single Circuit, Series: 61036, 125 V, 5 A, 1 Poles, Contact Configuration: SPST, On/Off, 2-Wire Terminal, Nickel Plated, UL Listed
Jandorf 61123 Single Circuit Push Button Switch Mintcraft L752-26-03 Freedom Arrow Hart 1113-SP 3-Hole Weatherproof Outlet Box
Jandorf Push Button Switch, Single Circuit, Series: 61123, 125 V, 10 A, 1 Poles, Contact Configuration: SPST, Normally Off, Momentary Operation, 2-Screw Terminal, UL Listed Zinc alloy with roller. Bagged Electrostatically painted with a baked, weather-resistant powder finish. Accept single gang weatherproof covers and standard FS covers. Mounting lugs provide strength and durability on any mounting surface. Raised knockout studs on back of box provide alternative means for wall mounting. Strike desired studs with sharp hammer blow for clean mounting holes. Ground screw hole located inside back wall of box. Threaded outlets for conduit and connectors. Two closure plugs and mounting lugs furnished. Three holes, one at each end and one on the back. 2" depth x 2.812" width x 4.562" length. UL Listed. Carded.
Cooper C1303-7LTV-L Lighted Grounding Toggle Switch Cooper C1303-7LTW-L Lighted Grounding Toggle Switch Jandorf 61130 Double Circuit Toggle Switch