Home > ELECTRICAL > SPECIALTY ELECTRICAL > COMPUTER ACCESSORIES > DATA CABLE/WIRE & ACCESSORIES
Choose a sub category:
WALL CHANNEL- WIREMOLD
Sort By:
1
Halex 91530 Combination Coupling Halex 90510 Twin Screw Clamp Connector TAPE ELECT VNYL BLK 3/4INX60FT
Zinc die cast. Use to join EMT conduit to non-metallic sheathed cable. #14/2, #12/3 or 2 #14/2. Indoor use only. With UPC. UL Approved. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Black vinyl electrical tape for common electrical uses. 7 mil., UL Approved.
Intertape 602 Electrical Tape Halex 96510 2-Piece Butterfly Clamp Connector Calterm 49305 Electrical Tape 30 ft L x 7.5 mil T
General purpose electrical insulating tape, good dielectric strength. 7 mils thick. UL Listed and CSA Certified. Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required. Black PVC electrical tape is UL Listed to 600 volt. 7.5 mil. thickness and a temperature rating up to 80 degrees Celsius/176 degrees Fahrenheit. Elongation of 200 percent allows tight wrapping and sealing.
Halex 90512 Twin Screw Clamp Connector WireGard 19-AWC Assortment Wire Connector Kit WireGard 19-001 Twist-On Wire Connector
Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WireGard 19-002 Twist-On Wire Connector WireGard 19-003 Twist-On Wire Connector WireGard 19-004 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WireGard 19-006 Twist-On Wire Connector WingGard 19-084 Twist-On Wire Connector WingGard 19-086 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Hex-Lok 19-2H2 Hex Lock Wire Connector WingGard 19-089 Twist-On Wire Connector GreenGard 19-095 Grounding Wire Connector
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections.
Bell Raco 5173-2 Blank Weatherproof Device Cover Bell Raco 5173-1 Blank Weatherproof Device Cover Halex 27511 Hit Lock Cable Connectors
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified.
Cooper RKRD-W-BP Replacement Knob Cooper RKRD-V-BP Replacement Knob CordMate Legrand C Wireway Outside Elbow
CULus Listed, NOM certified. CULus Listed, NOM certified. Hides and organizes loose cords and wires.
CordMate Legrand C Wireway Inside Elbow CordMate Legrand C Wireway Flat Elbow Intertape 85828 Electrical Tape
Hides and organizes loose cords and wires. Hides and organizes loose cords and wire. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85827 Electrical Tape Intertape 85835 Electrical Tape Intertape 85830 Electrical Tape
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85832 Electrical Tape Intertape 85831 Electrical Tape CordMate Legrand C19 Channel Coupling
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. Joins channels that hide and organize loose cords and wires. UL Listed.
Halex 90513 Twin Screw Clamp Connector Bell Raco 5173-7 Blank Weatherproof Device Cover Hubbell 5173-5 Blank Weatherproof Cover
Fits non metallic cable number 14/2 to number 6/3 AWG or number 3/10/3 AWG or flex cord .450 to .730 inches diameter. With a 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated.
Hubbell 5173-6 Blank Weatherproof Cover Lutron Preset/Slide-to-Off Standard Replacement Knob Lutron Replacement Knob
Outdoor use, rugged metallic construction. Powder coat finish. Scratch resistant. Includes installation hardware, gasket, and multi-lingual instructions. C/UL/US UL Listed. NEMA 3R rated. Replacement knob for Skylark dimmers. Replacement knob for Skylark dimmers.
Halex 20511 Twin Screw Clamp Connector CordMate II Legrand C Wireway Flat Elbow Bell 5269-5 Closure Plug
Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Hides and organizes loose cords and wire. For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets.
Bell 5269-7 Closure Plug Bell 5269-6 Closure Plug CordMate II Legrand C Wireway Inside Elbow
For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. For making a 90 degree turn around an inside corner from wall-to-wall or wall-to-ceiling.
CordMate II Legrand C Wireway Outside Elbow CordMate II Legrand C59 Joint Cover Channel Coupling CordMate II Legrand C 3-Way Standard T-Fitting
For making a 90 degree turn around an outside corner. Joins channels that hide and organize loose cords and wires. UL Listed. For installation requiring 3-way branching including 90-degree angle.
Scotch 4218-BA-40 Electrical Tape Halex 90514 Twin Screw Clamp Connector Jandorf 60935 Closed End Connector 22 - 18 AWG
Commercial grade 7-mil polyvinyl chloride insulating tape, flame retardant and provides mechanical protection with minimum bulk. Excellent resistance to abrasion, moisture, acids, copper corrosion and varying weather conditions. UL Listed and CSA Certified. Fits non metallic cable number 6/3 to number 2/3 AWG flex cord .800 to 1.350 inches diameter or SE cable 3 conductor or 3 number 1/0 minimum; 3 conductor or 3 number 2/0 maximum. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Jandorf Closed End Connector Series: 60935, 22 - 18 AWG Conductor, Fully Insulated Insulation, Vinyl Insulation, Clear, Tin Plated Copper, UL Listed
Bell 5269-0 Closure Plug Gardner Bender 20-410 Crimp Sleeve Connector Calterm 61470 Assortment Wire Cap Set
For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. Zinc plated steel. Suitable for solid or stranded copper wire.
Bell 5270-5 Closure Plug WireGard 25-002 Twist-On Wire Connector Gardner Bender GTF-300 Friction Tape
For use with weatherproof boxes, extension adapters, cluster covers and round splice boxes to seal off unused outlets. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. For use over electrical tape splices. Matted finish provides the best gripping surface available. Use to wrap grips on hand tools.
WireGard 25-001 Twist-On Wire Connector GB-Gardner Bender GTB-667P Electrical Tape GB-Gardner Bender GTW-667P Electrical Tape
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2.
Hex-Lok 19-1H1 Hex Lock Wire Connector Hubbell 5374-0 Blank Round Flat Weatherproof Cover Lutron Electronics RK-WH Replacement Knobs
Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs. For use with 4" round splice boxes. Installation hardware, and gasket included. 4" diameter, shrink wrapped. UL Listed. Replacement knob for Rotary dimmers.
Lutron RK-IV Standard Replacement Knob GB-Gardner Bender GTO-667P Electrical Tape TAPE ELECTRICAL 3/4INX12FT
Replacement knob for Rotary dimmers. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Quality electrical tape designed for general purpose electrical applications. Made from low-lead PVC material. For applications up to 600 V. Temperature rating up to 176 degrees F (80 degrees C). Assorted colors (red, white, blue, green and yellow).
Gardner Bender 20-411 Crimp Sleeve Connector WireGard 25-003 Twist-On Wire Connector Gardner Bender 20-089 Closed End Crimp Pigtail Connector
Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed.
Gardner Bender 20-090 Closed End Crimp Pigtail Connector Gardner Bender GMC-88M5 Modular Electrical Plug Bell Raco 5175-1 Blank Weatherproof Device Cover
Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed. Use with network/twisted pair cable CAT-5E, 8-position, 8-contact, rounded cable, solid wire. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2".
Legrand NM7 Nonmetallic Raceway Inside Elbow Legrand NM8 Nonmetallic Raceway Outside Elbow Wiremold NM910 Connection Cover
For making a 90 degree inside turn around a corner from wall-to-wall or wall-to-ceiling. For making a 90 degree outside turn around a corner. Mounting components for NMI wire channel, including screws and anchors, wire clips and joint cover.
CordMate Legrand NM Raceway Wireway Inside Elbow Legrand NMW910 Raceway Accessory Pack CordMate Legrand NM Raceway Wireway Outside Elbow
For making a 90 degree inside turn around a corner from wall-to-wall or wall-to-ceiling. Mounting components for NMI wire channel, including screws and anchors, wire clips and joint cover. For making a 90 degree outside turn around a corner.
Jandorf 60820 Closed End Connector 12 - 10 AWG Hubbell 5193-0 3-Hole Cluster Lampholder Cover Bell Raco 5193-1 Round Cluster Cover
Jandorf Closed End Connector Series: 60820, 12 - 10 AWG Conductor, Insulated Insulation, Nylon Insulation, Clear, Tin Plated Copper, UL Listed For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed.
PushGard 19-PC2 2-Port Push-In Connector Halex 27519 Hit Lock Cable Connectors PushGard 19-PC3 3-Port Push-In Connector
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only.
Arrow Hart S2962 Weatherproof Cover Hubbell 5175-5 Blank Weatherproof Cover Hubbell 5186-0 1-Hole Cluster Lampholder Cover
Tough plastic construction, resistant to high impact and sunlight. Non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Self closing cover. Vertical only. UL Listed for wet locations with cover closed. For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". For wet locations. Gasket, screws and plugs included. Use 75-150 watt maximum, Par-38 lamps. Die cast zinc, powder coat finish provides maximum weatherability and scratch resistance. Includes installation hardware, gasket, and multi-lingual instructions. One 1/2" NPT hole. Underwriters Recognized Component CSA C22.2 No. 18 NEMA 3R Rated.
Hubbell 5180-0 Weatherproof Device Cover WingGard 25-084 Twist-On Wire Connector Bell Raco 5186 Rectangular Cluster Cover
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. For wet locations. Gasket, screws and plugs included. Use 75-150 watt maximum, Par-38 lamps. Die cast zinc, powder coat finish provides maximum weatherability and scratch resistance. Includes installation hardware, gasket, and multi-lingual instructions. One 1/2" NPT hole. Underwriters Recognized Component CSA C22.2 No. 18 NEMA 3R Rated.
Super 33+ 195NA Electrical Tape Bell Raco 5186-6 1-Hole Cluster Rectangular Weatherproof Cover Hubbell 5180-6 Weatherproof Device Cover
For insulating, repairing and protecting electrical wire. UL Listed. For wet locations. Gasket, screws and plugs included. Use 75-150 watt maximum, Par-38 lamps. Die cast zinc, powder coat finish provides maximum weatherability and scratch resistance. Includes installation hardware, gasket, and multi-lingual instructions. One 1/2" NPT hole. Underwriters Recognized Component CSA C22.2 No. 18 NEMA 3R Rated. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
PushGard 19-PC4 4-Port Push-In Connector WireGard 25-004 Twist-On Wire Connector Gardner Bender DS-110N Duct Seal Insulator
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Malleable non-conductive compound for sealing of electrical raceway connections from air, noise and moisture.
Bell Raco 5175-0 Blank Weatherproof Device Cover Gardner Bender TK-32 Assortment Wire Connector Kit Halex 05115 Twin Screw Clamp Connector
For use whenever weatherproof protection is required for a weatherproof box. Rugged die cast construction. Powder coat finish provides scratch resistance. Includes gasket and mounting hardware. Multi-lingual instructions in each package. UL Listed, NEMA 3R Rated. 4-1/2" x 4-1/2". Slide card kit with 32 assorted wire connectors: 10 GB #1 - minimum 3 #22 maximum 2 #16, 8 GB #2 - minimum 3 #22 maximum 3 #18 w/2 #20 6 GB #3 - minimum 3 #20 maximum 2 #14, 2 GB #4 - minimum 1 #14 maximum 4 #12, 4 crimp connector #1035 - 1 #20 w/1 #12 - 2 #14, 2 crimp connector #1034 - 4 #22 - 2 #16. Fits non metallic cable, flex cords, multi flex cords; fitting range .834 - 1.520 inches diameter SE cables 2 conductor 4/0. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed.
Decko 38120 Diamond Design Towel Bar Bell Raco 5193-7 3-Hole Cluster Lamp Holder Cover Bell Raco 5193-5 Round Cluster Cover
Special diamond design helps prevent towel slipping and snagging. Die-cast appearing mounting plates. Scratch and rust resistant. Easy to install. Hardware included. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed.
Bell Raco 5193-6 Round Cluster Cover Hubbell 5197-0 3-Hole Cluster Lampholder Cover Bell Raco 5197-2 Round Cluster Cover
For wet locations. Gasket, screws and plugs included. 4" cluster cover. Use 75-150 watt maximum, Die cast zinc. One 1/2" NPT hole. UL Listed. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed.
Bell Raco 5189 Rectangular Cluster Cover Bell Raco 5189 Rectangular Cluster Cover Hubbell 5189-0 3-Hole Cluster Lampholder Cover
Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant. Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant. Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant.
Bell Raco 5197-1 Round Cluster Cover WingGard 25-086 Twist-On Wire Connector Gardner Bender GTP-307WD All Weather Electrical Tape
For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit.
Bell Raco 5180-1 2-Hole Weatherproof Device Cover Bell Raco 5180-2 2-Hole Weatherproof Device Cover Legrand NM11 T-Fitting
Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. For branching wire channel in two directions at 90 degree angles.
CordMate Legrand NMW11 3-Way T-Fitting Bell Raco 5606 Lampholder Bell Raco 5606 Lampholder
For branching wire channel in two directions at 90 degree angles. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed.
Hubbell 5606 Adjustable Weatherproof Lampholder Hubbell 5180-5 Weatherproof Device Cover Bell Raco 5180-7 2-Hole Weatherproof Device Cover
Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated. Horizontal device mount. Weatherproof covers for protection of outdoor receptacles. State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" x 2-3/4". UL 514-A listed, File E195978 CSA C22.2 No. 18 NEMA 3R Rated.
Gardner Bender RTP-3422 Self-Sealing Electrical Tape Legrand NM6 Nonmetallic Raceway Flat Elbow CordMate Legrand NM Raceway Wireway Flat Elbow
Insulates and seals surfaces. Fuses to itself during application to stay watertight. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. For making 90 degree right or left turns on a flat surface. For making 90 degree right or left turns on a flat surface.
3M 10414 Electrical Tape Halex 26512 2-Piece Butterfly Clamp Connector Decko 38110 Diamond Design Towel Bar
Resists water, oils, alkalies, acids, weather, ultraviolet rays, abrasion, corrosion and moisture. Use as a primary insulation for wide cable splices up to 600 volt, for fixture and wire splices up to 1000 volt and to maintain electrical and high temperature integrity of electrical systems. 7 mil, UL Approved and CSA Certified. Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required. Special diamond design helps prevent towel slipping and snagging. Die-cast appearing mounting plates. Scratch and rust resistant. Easy to install. Hardware included.
Bell Raco 5189 Rectangular Cluster Cover Bell Raco 5197-5 Round Cluster Cover Hubbell 5189-6 3-Hole Cluster Lampholder Cover
Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Includes installation hardware, gasket, and multi-lingual instructions. 3 hole covers are supplied with two closure plugs. Die cast zinc construction. Three 1/2" NPT holes. UR - Underwrites recognized component CSA C22.2 No. 18 compliant.
Hubbell 5197-6 3-Hole Cluster Lampholder Cover Bell Raco 5197-7 3-Hole Cluster Round Weatherproof Cover DryConn 20101 Low Voltage Wire Connector
For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. For wet locations. Gasket, screws and plugs included. 4" cluster cover. Die cast zinc. Three 1/2" NPT holes. UL Listed. Suitable for all low voltage applications. For use in lighting, irrigation, and underground wiring. No junction box required. Filled with petroleum based sealant. 30 volt/10 amps maximum. 13/16" x 19/16".
Bell Raco 5152-0 Weatherproof Device Cover DryConn 62310 Safety Sealed Waterproof Wire Connector Hubbell 5155-5 Single Device Cover
State-of-the-art powder coat finish provides maximum weatherability and scratch resistance. Self-closing lids assure weatherproof protection when the receptacle is not in use. Installation hardware, gasket, multi-lingual instructions included. For single 1.406" diameter receptacle. UL Listed for wet location with cover closed. Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL Listed. With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated.
Bell Raco 5155-6 Round Opening Weatherproof Device Cover Bell Raco 5606 Adjustable Lampholder Legrand B-8 Metal Raceway Outside Elbow
With powder coat finish for weatherability and scratch resistance. For use whenever weatherproof protection is required for an outdoor receptacle. Self-closing lid for weatherproof protection when the receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. Size: 4-1/2" length x 2-3/4" width x 1.406" depth. UL Listed, Meets Standard 514A, C22.2 No. 18, (5103 series) NEMA 3R rated. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. Used to make a 90 degree outside turn around a corner.
Bell Raco 5606 Lampholder Hubbell 5606 Adjustable Weatherproof Lampholder Arrow Hart S1962W-SP Weatherproof Cover
Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. Die cast zinc with porcelain socket. For wet locations. Use 75-150 watt maximum, Par-38 lamps. Includes gaskets and locknuts. UL Listed. Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2".
Arrow Hart S1961 Weatherproof Cover Mintcraft CP-323L Wire Cap Set Arrow Hart S1962 Utility Halogen Low Profile Weatherproof Cover
Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations. Thirty two piece, for AWG #24 to AWG #10 solid or standard copper wire. Contains: 10 pc wire joint 22-16  300 volt, 2/#22 - 2/#16. 8 piece wire joint 22-14 300 volt 3/#22 - 3/#16. 6 pc wire joint 22-14 600 volt 2/#18 - 4/#16. 2 piece wire joint 18-12 600 volt 1/#18 + #14 - 1 and 2/#14 + 3/#16. 4 piece closed end pigtail 16-14 2/#22 - 2/#14. 2 piece closed end pigtail 12-10 2/#18 - 2/#10. Tough plastic construction, resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. UL Listed for damp locations. Stay open lids. Size 2-3/4" x 4-1/2".
Gardner Bender GMC-88C6 Modular Electrical Plug CONNCTOR WIRE IND/OTD AQUA/ORG CONNCTOR WIRE IND/OTD AQUA/RED
Use with network/twisted pair cable CAT-6, 8-position, 8-contact, rounded cable, solid wire. Aqua/Orange. No. 12 to No. 22 awg wire range, 600/1000 volts. Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL listed. Aqua/Blue. No 8 to No. 22 awg wire range, 600/1000 volts. Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL listed.
Arrow Hart S1961W-SP Weatherproof Cover Scotch Super 33+ 6132 Electrical Tape Decko 38170 Diamond Design Towel Bar
Resistant to high impact and sunlight. Non-metallic, non-corrosive and non-conductive. Gasket provided seals both device openings and edges. Lid stays open in use. UL Listed for damp locations. Resists water, oils, alkalies, acids, weather, ultraviolet rays, abrasion, corrosion and moisture. Use as a primary insulation for wide cable splices up to 600 volt, for fixture and wire splices up to 1000 volt and to maintain electrical and high temperature integrity of electrical systems. 7 mil, UL Approved and CSA Certified. Special diamond design helps prevent towel slipping and snagging. Die-cast appearing mounting plates. Scratch and rust resistant. Easy to install. Hardware included.
Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape
Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified.
Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape DryConn 10600 Twist-On Underground Wire Connector
Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Rated for all underground direct bury applications. Use on all lighting, irrigation, and underground wiring. Additional sealant for long term service. No junction box needed. 600 volt maximum with building wire, 1000 volt in fixtures and signs. #8 to #22 wire range. UL Listed.
Legrand B-6 Metal Raceway Flat Elbow Legrand B-7 Metal Raceway Inside Elbow WireGard 25-AWC Assortment Wire Connector Kit
Used to make a 90 degree right or left turn on a flat surface. Used to make a 90 degree inside turn around a corner, from wall-to-wall or wall-to-ceiling. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Bell Raco 5611-0 Replacement Outer Gasket WireGard 25-006 Twist-On Wire Connector Mintcraft 618S26-03 Freedom
Replacement gasket for Bell lampholders. UL Standard CSA Certified. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Bright chrome finish. Bagged.
PushGard 19-PC8 8-Port Push-In Connector Halex 05120 Twin Screw Clamp Connector Super 33+ 200 Electrical Tape
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Fits non metallic cable, flex cords, multi flex cords fitting range 1.085 - 1.520 inches diameter. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed. Vinyl electrical tape, black, 7 mil thick with PVC backing, provides protective jacketing for high-voltage cables and wire harnesses, and primary electrical insulation for splices up to 600 volt. Abrasion, corrosion, and UV resistant, resists alkalis and acids, and is flame-retardant. All-weather performance in cold to 0 degrees F or heat to 220 degrees F. UL Listed and CSA Certified.
Halex 20510 Twin Screw Clamp Connector Decko 38190 3-Arm Towel Rack Gardner Bender GSW-32 Pull Chain Switch
Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Triple drying action. Arms hinged in sturdy back plate. Scratch and rust resistant. Easy to install. Hardware included. Mounts in 13/32" diameter hole. Two position, 2 wire. (GSW-35 mounts in 1/2" diameter hole). number 18 AWG, 6" stripped wire leads.
Scotch 03407 Friction Tape Bell Raco 5103-0 1-Hole Weatherproof Device Cover Bell Raco 5103-1 1-Hole Weatherproof Device Cover
GFCI VERT 1G COVER GRAY
Our Price: $4.88
Good abrasion resistance, used for protection for electrical tape splices and connectors. Made in the USA. UL Approved. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped.
Bell Raco 5103-2 1-Hole Weatherproof Device Cover Halex 20512 Twin Screw Clamp Connector CordMate Legrand C10 Wire Channel
Includes installation hardware, gasket, and multi-lingual instructions. Weatherproof protection for outdoor receptacle. Powder coat finish for weather. Scratch resistance. Self-closing lid protects receptacle when not in use. C/UL/US NEMA 3R rated. Shrink wrapped. Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Hides and organizes low voltage loose cords and wires. UL Listed. 1/2" height x 3/8" width x 5' length.
Carlon E98TSCN-CAR Weatherproof Device Cover WireGard 10-001 Twist-On Wire Connector Scotch 88 Cold Weather Electrical Tape
Weatherproof cover for single toggle switch applications. Vertical mount. UV resistant, suitable for outdoor use. Nonmetallic/noncorrosive, won't rust or fade, paintable. UL Marine Listed, CSA Certified. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Thick 8.5 mil. Recommended for low temperature applications because of its superior cold weather handling features. Flexible for use on small wires. Inside or outside. Resists cold, ultraviolet rays, moisture, alkalies, acids and corrosion.
Bell Raco 5146-0 1-Hole Weatherproof Device Cover GreenGard 25-095 Grounding Wire Connector GB-Gardner Bender GSW-39 Canopy Switches
Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated. Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections. Momentary action. Variable speed and two-circuit brass plated pull chain switches for multifunction applications. Push-in connections for #18 AWG wire. Recommended mounting hole .406 diameter. 4 position 3 wire. Wire lead terminal type.
Carlon E98DHGN-CAR Weatherproof Cover WireGard 10-002 Twist-On Wire Connector Hex-Lok 25-2H2 Hex Lock Wire Connector
Non-conductive, corrosion resistant, and paintable for safe installation and operation in wet or damp locations. NEMA 3R rated and UL Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Hex-Lok 25-1H1 Hex Lock Wire Connector Intertape 5517 Electrical Tape Hubbell 5101-6 Weatherproof Device Cover
Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs. Semi-cured rubber for low voltage electrical insulation, 30 mil. Self-vulcanizing and water resistant. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Jandorf 61202 Canopy Switch AmerTac Zenith PN10075EB CAT5E Network Cable Hubbell 5121-5 Weatherproof Device Cover
Jandorf Pull Chain Switch, 2-Speed, 125 V, 3 A, 1 Poles, 2 Circuits, Off/On/On, 3-Push Terminal, Brass, Standards: UL Listed Connects computer to hub or RJ45 wall jack. Black cable. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated.
CONNECTOR WIRE ASSORTMNT 158PC Diva D-600RH-DK Turn-To-On Rotary Dimmer Legrand NMW17 Raceway Conduit Connector
Cone shaped springs pull wire into the connectors for a firm & secure grip. Pretwisting wires is not required. Maximum rated voltage: Grey, blue, & orange: 300 Volts; Yellow & red: 600 Volts. Neatly organized PVC storage case. Includes 2 changeable control knobs, one ivory and one white to match either color wall plate, (wall plate sold separately). Rotate to select light level, rotary on/off. Rated at 120 volt, 60Hz, works with 120 volt incandescents and halogens. 600 watt maximum capacity. UL/CSA Listed. For transitioning from nonmetallic raceway to conduit. Hides and organizes loose cords and wires.
Wiremold Raceway On-Wall Mount Conduit Connector Mintcraft 624S26-03 Freedom Bell Raco 5146-5 Weatherproof Device Cover
For transitioning from nonmetallic raceway to conduit. Hides and organizes loose cords and wires. Bright chrome finish. Bagged. Waterproof protection for outside receptacle. Metallic construction, powder coat finish. Scratch resistant. Self-closing lid when not in use. Includes installation hardware, gasket, and multi-lingual instructions.  4-1/2" length x 2-3/4" width. C/UL/US UL 514-A listed, File E195978 (5132-5146) CSA C22.2 No. 18 (5132-5146) NEMA 3R rated.
Diva Traditional D-600PH-DK Push-On Rotary Dimmer 3M DBO/B-6 Underground Splice Kit WingGard 25-089 Twist-On Wire Connector
Includes 2 changeable control knobs, one ivory and one white to match either color wall plate, (wall plate sold separately). Rotate to select light level, push on/off. 3-way dimmers require 3-way switches. Rated at 120 volt AC, 60Hz, works with 120 volt incandescents and halogens. 600 watt maximum capacity. UL and CSA Listed. Designed to connect and moisture seal electrical connection for direct bury applications, 18-10 AWG, rated up to 600 volts. Combines the quick, reliable connection of a spring connector O/B with the moisture resistance of a high-impact, UV-resistant tube prefilled with moisture-resistant grease. For use with irrigation systems on golf courses, around business and for outdoor lighting systems. Application temperature range 32 - 120 degrees Fahrenheit. EU RoHS Compliant. Flame retardant. UL listed for direct bury. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Decko 38140 Twin and Diamond Design Towel Bar Bell Raco 5101-2 1-Hole Weatherproof Device Cover Bell Raco 5101-1 1-Hole Weatherproof Device Cover
Chrome plated for durability. Diamond bar design helps prevent towel slipping and snagging. Die-cast appearing mounting plates. Scratch and rust resistant. Easy to install. Hardware included. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Bell Raco 5101-0 1-Hole Weatherproof Device Cover Bell Raco 5121-1 Weatherproof Switch Cover Hubbell 5101-5 Weatherproof Device Cover
For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated. For use whenever weatherproof protection is required for an "on/off" type switch. Powder coat finish. Supplied with a switch unassembled to the cover - no need to purchase separate components. Includes installation hardware and multi-lingual instructions. Size 4-1/2" length x 2-3/4" width. UL Listed, CSA, NEMA 3R Rated. For outdoor horizontal use. Powder coat finish. Scratch resistant. Self-closing lid assures protection when receptacle is not in use. Includes installation hardware, gasket, and multi-lingual instructions. UL 514-A listed, File E 195978 C/UL CSA C22.2 No. 18  NEMA 3R rated.
Gardner Bender HTP-1010 Self-Sealing Tape Bell Raco 5101-7 1-Hole Weatherproof Device Cover 3M 10457 Assortment Colored Electrical Tape Kit