Home > ELECTRICAL > SPECIALTY ELECTRICAL > AUDIO & VIDEO SUPPLIES
Choose a sub category:
TV WIRE/CABLE TV WIRE/CABLE FITTINGS ANTENNAS
ANTENNA ACCESSORIES VIDEO ACCESSORIES AUDIO ACCESSORIES
Sort By:
1
Carlon E940D-CTN Standard Conduit Coupling Carlon E943D-CTN Terminal Adapter Halex 97521 Insulated Conduit Bushing
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Carlon E940E-CTN/CAR Standard Conduit Coupling Carlon E942DR-CTN Conduit Adapter Arrow Hart 2131 Standard Wall Plate
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Molded from non-flammable thermoset. Flush fitting, warp resistant design. Screw-catch feature holds mounting screws captive and simplifies installation. Matching screws provided. High gloss finish is soil resistant. Standard size - 2.75" x 4.50", boxed.
Arrow Hart 2131V-BOX Round Wall Plate Carlon E942ER-CTN Conduit Adapter Carlon E940FR-CTN Standard Conduit Coupling
Molded from non-flammable thermoset. Flush fitting, warp resistant design. Screw-catch feature holds mounting screws captive and simplifies installation. Matching screws provided. High gloss finish is soil resistant. Standard size - 2.75" x 4.50", boxed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E943E-CTN Terminal Adapter Halex 97522 Insulated Conduit Bushing Carlon E943FR-CTN Terminal Adapter
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance.
Halex 97525 Insulated Conduit Bushing Carlon E996DR-CTN Conduit Box Adapter Carlon E940GR-CTN Standard Conduit Coupling
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For PVC enclosures. cULus Listed. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Halex 96191 Rigid IMC Conduit Locknut Carlon E942FR-CTN Conduit Adapter Carlon UA9ADB-CTN Standard Radius Rigid Conduit Elbow
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Carlon E996ER-CTN Conduit Box Adapter Carlon UA9ADR-CTN Standard Radius Conduit Elbow Halex 97523 Insulated Conduit Bushing
For PVC enclosures. cULus Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Carlon E940HR-CTN Standard Conduit Coupling Halex 96071 Knock Out Seals Carlon E943GR-CTN Terminal Adapter
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance.
Carlon UA7ADB-CTN Standard Radius Conduit Elbow Carlon A240D-CAR 1-Piece Conduit Coupling Halex 96072 Knock Out Seals
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Cooper 1301-7B Framed Grounding Toggle Switch Cooper 1301-7V Framed Grounding Toggle Switch Cooper 1301-7W Framed Grounding Toggle Switch
Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed.
Cooper 270B Grounded  Duplex Receptacle Cooper 270V Grounded  Duplex Receptacle Cooper 270W Grounded  Duplex Receptacle
Built-in wire stripper for number 14 wire. Built-in wire looper for pre-looping conductors. Screw-catch feature eliminates need to hand-thread screw and possible cross-threading. Double wipe ground contacts. Split circuit break-off tab. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire only. 15 amp/125 volt. UL Listed, NOM certified, meets CSA requirements. Built-in wire stripper for number 14 wire. Built-in wire looper for pre-looping conductors. Screw-catch feature eliminates need to hand-thread screw and possible cross-threading. Double wipe ground contacts. Split circuit break-off tab. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire only. 15 amp/125 volt. UL Listed, NOM certified, meets CSA requirements. Built-in wire stripper for number 14 wire. Built-in wire looper for pre-looping conductors. Screw-catch feature eliminates need to hand-thread screw and possible cross-threading. Double wipe ground contacts. Split circuit break-off tab. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire only. 15 amp/125 volt. UL Listed, NOM certified, meets CSA requirements.
Carlon UA9AER-CTN Standard Radius Conduit Elbow Halex 96192 Rigid IMC Conduit Locknut RECEPTACLE DUPLEX 15A 125V LA
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Built-in wire stripper for number 14 wire. Built-in wire looper for pre-looping conductors. Screw-catch feature eliminates need to hand-thread screw and possible cross-threading. Double wipe ground contacts. Split circuit break-off tab. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire only. 15 amp/125 volt. UL Listed, NOM certified, meets CSA requirements.
Halex 26190 Conduit Locknut Halex 97524 Insulated Conduit Bushing Halex 96193 Rigid Conduit Locknut
Halex Conduit Locknut, 1/2 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Carlon UA7ADR-CAR Standard Radius Conduit Elbow Carlon E943HR-CTN Terminal Adapter Carlon UA9AEB-CTN Standard Radius Rigid Conduit Elbow
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Carlon E942GR-CTN Conduit Adapter Thomas & Betts E950ED-CTN Reducing Bushing WALLPLATE RCPT LT ALMOND 1G
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. Virtually unbreakable, with high structural rigidity, long-term form retention and impact and abrasion resistance. Screw-catch feature holds mounting screws captive. Matching screws provided. High gloss finish is soil resistant. Mid-size - 3.125" x 4.875".
Carlon A243D-CAR 1-Piece Snap-In Conduit Adapter Carlon A253E-CAR 1-Piece Snap-In Terminal Adapter Carlon UA7AER-CAR Standard Radius Conduit Elbow
Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Carlon E940JR-CTN Standard Conduit Coupling Carlon E942HR Conduit Adapter Carlon UA7AEB-CTN Standard Radius Conduit Elbow
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Carlon A253D-CAR 1-Piece Snap-In Terminal Adapter Halex 96194 Rigid IMC Conduit Locknut Carlon A240E-CAR 1-Piece Conduit Coupling
Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Carlon UA9AFR-CTN Standard Radius Conduit Elbow Carlon E943JRR Terminal Adapter Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
Carlon E942JR Conduit Adapter Carlon UA7AFR-CAR Standard Radius Conduit Elbow Carlon UA9AFB-CTN Standard Radius Conduit Elbow
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Halex 96195 Rigid Conduit Locknut Cooper TR270W  Tamper Resistant Duplex Receptacle Cooper TR270V  Tamper Resistant Duplex Receptacle
Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. UL, cULus Listed. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. UL, cULus Listed.
Carlon UA7AFB-CTN Standard Radius Conduit Elbow Thomas & Betts E994DR-CTN Conduit Offset Cooper TR270V Tamper Resistant Duplex Receptacle
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Non-conductive. Will not rust or corrode. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. UL, cULus Listed.
Cooper TR270W Tamper Resistant Duplex Receptacle RECEPTACLE DUPLEX LIGHT ALMOND Halex 26071 Knock Out Seals
Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. UL, cULus Listed. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. UL, cULus Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Halex 97526 Insulated Conduit Bushing Carlon E950FD-CAR Reducing Conduit Bushing Carlon UA9AGR-CTN Standard Radius Conduit Elbow
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon UA7AGR-CAR Standard Radius Conduit Elbow Carlon E940K-CTN Conduit Coupling Cooper 1172V Type F Wall Jack
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. For use with cable ready TV's, VCR's and outdoor antennas. For use with 75 ohm cable. Self-extinguishing, high impact thermoplastic meets UL 94V-O flame retardancy rating. Mounting and assembly hardware included.
Cooper 1172W Type F Wall Jack Arrow Hart CR15W  Duplex Receptacle Thomas & Betts E950FE-CTN Reducing Bushing
For use with cable ready TV's, VCR's and outdoor antennas. For use with 75 ohm cable. Self-extinguishing, high impact thermoplastic meets UL 94V-O flame retardancy rating. Mounting and assembly hardware included. Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Cooper 736B-BOX  Duplex Receptacle Cooper 736V-BOX  Duplex Receptacle Cooper 736W-BOX  Duplex Receptacle
Standard contacts. Side wire terminals accept up to #12 wire. Terminal screws backed out, ready for wiring. 15 amp/125 volt. UL Listed. Standard contacts. Side wire terminals accept up to #12 wire. Terminal screws backed out, ready for wiring. 15 amp/125 volt. UL Listed. Standard contacts. Side wire terminals accept up to #12 wire. Terminal screws backed out, ready for wiring. 15 amp/125 volt. UL Listed.
Carlon E943K-CTN Terminal Adapter Carlon UA7AGB-CAR Standard Radius Conduit Elbow Halex 96196 Rigid IMC Conduit Locknut
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Arrow Hart CR15B  Duplex Receptacle Arrow Hart CR15V  Duplex Receptacle Thomas & Betts E994ER-CTN Conduit Offset
Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed. Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed. Non-conductive. Will not rust or corrode.
Carlon UA9AH-CAR Standard Radius Conduit Elbow Halex 75225 Insulated Conduit Bushing Carlon UA7AHR-CTN Standard Radius Conduit Elbow
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Carlon E985D-CTN Rigid Conduit Body Carlon E984D-CTN Rigid Conduit Body Halex 01925B IMC Conduit Locknut
For easy access and pulling of wires through conduit run. Textured lid, foam-in-place gasket. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Bulk packed.
Carlon UB9AD-CAR Standard Radius Conduit Elbow Thomas & Betts E986D-CTN Type LB Rigid/IMC Conduit Body Cooper 1107V Decorator  Duplex Receptacle
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for number 14 and number 12 wire and wire looper for pre-looping. Combination slot/Phillips head mounting and terminal screws for installation with power screwdrivers. Terminal screws backed out - ready for wiring. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire. Temperature range of -40 to 65 degrees C. Meets all UL 498 requirements, (file no. E15058), Fed. Specs. WC-596G, NOM Certified, CSA Certified, C22.2 no.42. Standard Grade: (file no.6914) (6233-01). Meets flammability requirements per UL94, V2 rated. 15 amp, 125 volt.
Cooper 1107W Grounded  Duplex Receptacle RECEPTACLE DECOR 2P 3W 15A LA Carlon E940LR/CTN Conduit Coupling
Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for number 14 and number 12 wire and wire looper for pre-looping. Combination slot/Phillips head mounting and terminal screws for installation with power screwdrivers. Terminal screws backed out - ready for wiring. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire. Temperature range of -40 to 65 degrees C. Meets all UL 498 requirements, (file no. E15058), Fed. Specs. WC-596G, NOM Certified, CSA Certified, C22.2 no.42. Standard Grade: (file no.6914) (6233-01). Meets flammability requirements per UL94, V2 rated. 15 amp, 125 volt. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for number 14 and number 12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to number 10 solid or stranded wire. Push in terminals accept number 14 solid wire. Screw-catch feature speeds wall plate installation. 15 amp, 125 volt. NEMA 5-15R. UL, cULus Listed. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E950GE-CAR Reducing Conduit Bushing Thomas & Betts E950GF-CTN Reducing Bushing Carlon UA9AGB-CTN Standard Radius Conduit Elbow
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Carlon E987D-CTN Rigid Conduit Body RECEPTACLE BULK LT ALMOND 20A Cooper 7500-Box Decorative Standard Rocker Switch
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed. Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements.
Cooper 7500-Box Decorative Standard Rocker Switch Halex 75230 Insulated Conduit Bushing SWITCH/ROCKER 1P LA
SWITCH/ROCKER 1P LA
Our Price: $2.69
Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements.
Arrow Hart CR20W Grounded Duplex Receptacle Arrow Hart CR20V Grounded Duplex Receptacle Arrow Hart CR20B Grounded Duplex Receptacle
Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed. Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed. Triple wipe line contacts provide long-term plug retention. Double wipe ground contacts. 0.050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Side wire terminals accept up to #10 solid or stranded wire. Meets all UL 498 requirements UL Listed.
Carlon UA7AHB-CAR Standard Radius Conduit Elbow Carlon E983D-CTN Rigid IMC Conduit Body Spot-Gro C270V Duplex  Electrical Receptacle
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. Built-in wire stripper for number 14 wire. Built-in wire looper for pre-looping conductors. Screw-catch feature eliminates need to hand-thread screw and possible cross-threading. Double wipe ground contacts. Split circuit break-off tab. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire only. 15 amp/125 volt. UL Listed, NOM certified, meets CSA requirements.
Cooper C270W  Duplex Receptacle Thomas & Betts E950HGR Reducing Bushing Halex 26073 Knock Out Seals
Built-in wire stripper for number 14 wire. Built-in wire looper for pre-looping conductors. Screw-catch feature eliminates need to hand-thread screw and possible cross-threading. Double wipe ground contacts. Split circuit break-off tab. Side wire terminals accept up to number 10 solid or stranded wire. Push-in terminals accept number 14 solid wire only. 15 amp/125 volt. UL Listed, NOM certified, meets CSA requirements. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Carlon UA9AHB-CTN Standard Radius Rigid Conduit Elbow RECEPTACLE DECO AG LT ALMOND  Carlon E942K-CAR Conduit Adapter
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Terminal screws backed out-ready for wiring. Push-in terminals accept number 14 solid wire. Side wire terminals accept up to number 10 solid or stranded wire. Longer, wider strap provides 40 percent more contact area to wall board. Combination slot/Phillips head mounting and terminal screws ease installation with power screwdrivers. Virtually eliminates floating installations. Built-in wire stripper for number 14 and number 12 wire to speed installation. Built-in wire looper for pre-looping. Temperature range of -40 to 65 degrees C. Meets all UL 498 requirements, (file no.E15058), Fed.Specs.WC-596G, NOM Certified, CSA Certified, C22.2 no.42. Standard Grade: (file no.6914) (6233-01). Meets flammability requirements per UL94, V2 rated. 15 amp, 125 volt. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Carlon E943L-CAR Terminal Adapter Carlon UB9AE-CAR Standard Radius Conduit Elbow Cooper 1107-9BK Decorator  Duplex Receptacle
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Terminal screws backed out-ready for wiring. Push-in terminals accept number 14 solid wire. Side wire terminals accept up to number 10 solid or stranded wire. Longer, wider strap provides 40 percent more contact area to wall board. Combination slot/Phillips head mounting and terminal screws ease installation with power screwdrivers. Virtually eliminates floating installations. Built-in wire stripper for number 14 and number 12 wire to speed installation. Built-in wire looper for pre-looping. Temperature range of -40 to 65 degrees C. Meets all UL 498 requirements, (file no.E15058), Fed.Specs.WC-596G, NOM Certified, CSA Certified, C22.2 no.42. Standard Grade: (file no.6914) (6233-01). Meets flammability requirements per UL94, V2 rated. 15 amp, 125 volt.
Carlon E950JHR Reducing Conduit Bushing Arrow Hart BR15V  Duplex Receptacle Arrow Hart BR15W  Duplex Receptacle
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. High impact-resistant thermoplastic face. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. .050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Easy access split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Back and side wire terminals accept #14, #12 and #10 solid or stranded wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Federal specifications WC-596. Bulk Pak. UL Listed. High impact-resistant thermoplastic face. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. .050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Easy access split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Back and side wire terminals accept #14, #12 and #10 solid or stranded wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Federal specifications WC-596. Bulk Pak. UL Listed.
AmerTac 935DAL Wall Plate Arrow Hart 93111-BOX Standard Wall Plate Arrow Hart 93091-BOX Standard Wall Plate
With screws. 5" height x 2-3/4" width x 1/4" depth. Made of Type 304 stainless steel alloy for superior non-magnetic corrosion-resistant properties. Plates are 0.032" thick. Brushed satin finish resists fingerprints. Matching stainless steel mounting screws provided. Standard size - 2.75" x 4.50", with 1.594" hole. Made of Type 304 stainless steel alloy for superior non-magnetic corrosion-resistant properties. Plates are 0.032" thick. Brushed satin finish resists fingerprints. Matching stainless steel mounting screws provided. Standard size - 2.75" x 4.50", with 1.406" hole, boxed.
Cooper TR1107W Decorative Tamper Resistant Duplex Receptacle Cooper TR1107V Decorative Tamper Resistant Duplex Receptacle Halex 64405 Conduit Elbow
Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for number 14 and number 12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to number 10 solid or stranded wire. Push in terminals accept number 14 solid wire. Screw-catch feature speeds wall plate installation. 15 amp, 125 volt. NEMA 5-15R. UL, cULus Listed. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for number 14 and number 12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to number 10 solid or stranded wire. Push in terminals accept number 14 solid wire. Screw-catch feature speeds wall plate installation. 15 amp, 125 volt. NEMA 5-15R. UL, cULus Listed. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Carlon E983E-CTN Rigid IMC Conduit Body Carlon UB9AF-CAR Standard Radius Conduit Elbow Thomas & Betts E986E-CTN Type LB Rigid/IMC Conduit Body
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Cooper TR1107V Decorator Tamper Resistant Duplex Receptacle Cooper TR1107W Decorator Tamper Resistant Duplex Receptacle Carlon E985E-CTN Rigid Conduit Body
Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for number 14 and number 12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to number 10 solid or stranded wire. Push in terminals accept number 14 solid wire. Screw-catch feature speeds wall plate installation. 15 amp, 125 volt. NEMA 5-15R. UL, cULus Listed. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for number 14 and number 12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to number 10 solid or stranded wire. Push in terminals accept number 14 solid wire. Screw-catch feature speeds wall plate installation. 15 amp, 125 volt. NEMA 5-15R. UL, cULus Listed. For easy access and pulling of wires through conduit run. Textured lid, foam-in-place gasket. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Carlon E984E-CTN Rigid Conduit Body Thomas & Betts E986F-CTN Type LB Rigid/IMC Conduit Body Arrow Hart CSB GRD Pro Toggle Switch
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Small toggle switch blends with standard grade toggles. Larger contacts, backwire clamps on the side terminals. Side wire terminals accept up to number 10 solid wire. Back wire terminal accepts 12 or 14 gauge wire. Heavy duty cam action mechanism. Long, broad steel mounting strap, zinc-plated for corrosion resistance. Built-in wire stripper for number 12 and number 14 wire. Ground screw terminal, stippled line and ground contacts standard. Tri-Combo head mounting and terminal screws. 15 amp, 120/277 volt. cULus Listed, NOM certified.
Arrow Hart CSB GRD Pro Toggle Switch LOCK NUT SEALER 1/2IN         SWITCH AC QUIET LT ALMOND
LOCK NUT SEALER 1/2IN
Our Price: $3.36
Small toggle switch blends with standard grade toggles. Larger contacts, backwire clamps on the side terminals. Side wire terminals accept up to number 10 solid wire. Back wire terminal accepts 12 or 14 gauge wire. Heavy duty cam action mechanism. Long, broad steel mounting strap, zinc-plated for corrosion resistance. Built-in wire stripper for number 12 and number 14 wire. Ground screw terminal, stippled line and ground contacts standard. Tri-Combo head mounting and terminal screws. 15 amp, 120/277 volt. cULus Listed, NOM certified. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896.
Arrow Hart CS Compact Toggle Switch Arrow Hart CS Compact Toggle Switch Arrow Hart Eagle CS Lighted Toggle Switch
Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896. Side wire terminals accept up to number 10 solid or stranded wire. Rated for fluorescent lighting fixtures typical in commercial applications. 0.050" thick steel mounting strap zinc-plated for corrosion resistance. Ground screw terminal standard. Meets all UL 20 requirements, Federal specifications WS896.
Halex 26074 Knock Out Seals Zenith VA1002RG6CR Type F Coaxial Connector Zenith VA1002RG6FT Type F Coaxial Connector
Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Connects to RG6 coax cable. Crimping tool required. .87" height x .5" width x .5" depth. Connects two coaxial cables. .75" height x .5" width x .5" depth.
Carlon UA7AJ-CAR Standard Radius Conduit Elbow AmerTac 935DW Wall Plate Cooper 1301-7 Framed Grounded Toggle Switch
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. With screws. 5" height x 2-3/4" width x 1/4" depth. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed.
Cooper 1301-7 Framed Grounded Toggle Switch Carlon E983FR-CTN Rigid IMC Conduit Body Arrow Hart BR20V  Duplex Receptacle
Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. High impact-resistant thermoplastic face. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. .050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Easy access split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Back and side wire terminals accept #14, #12 and #10 solid or stranded wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Federal specifications WC-596. Bulk Pak. UL Listed.
Arrow Hart BR20W  Duplex Receptacle Zenith VA1002RG6TW Type F Coaxial Connector Arrow Hart BR20A  Duplex Receptacle
High impact-resistant thermoplastic face. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. .050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Easy access split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Back and side wire terminals accept #14, #12 and #10 solid or stranded wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Federal specifications WC-596. Bulk Pak. UL Listed. Connects to coax cable without tools. .75" height x .5" width x .5" depth. High impact-resistant thermoplastic face. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. .050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Easy access split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Back and side wire terminals accept #14, #12 and #10 solid or stranded wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Federal specifications WC-596. Bulk Pak. UL Listed.
Carlon E987E-CTN Rigid Conduit Body Carlon UA7AJB-CAR Standard Radius Conduit Elbow Carlon E942L-CAR Conduit Adapter
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Carlon E990DR-CAR Access Pull Standard Radius Conduit Elbow Halex 26075 Knock Out Seals Carlon UA9AJ-CAR Standard Radius Conduit Elbow
Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon UA9AJB-CAR Standard Radius Conduit Elbow American Tack and Hdwe VM1002RG6BU Zenith Coaxial Bushings Carlon E987F-CAR Rigid Conduit Body
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Allows coax cable to feed through wall an internal or external wall. 1.17" height x 1.17" width x 1.17" depth. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed.
Cooper 7500-Box Decorative Standard Rocker Switch Cooper 7500-Box Decorative Standard Rocker Switch Arrow Hart 39CH-BOX Wall Plate
Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements. Ultrasonic welding and integrated construction of the strap and body. Backwire clamps on the side terminals for installation of #12 and #14 wire. Thermoplastic rocker, top and backbody are virtually unbreakable. Screws accept slotted, Phillips and Robertson head tools for installation in both the U.S. and Canada. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Built-in wire stripper for #12 and #14 wire. Stippled ground screw standard. 15 amp, 120/277 volt AC rating for fluorescent lighting fixtures typical in commercial applications. Push in terminals accept #14 solid wire only. Temperature rating of -20 to 60 degrees C. Meets flammability requirements per UL 94, 6504, V2 rated, VO rated. UL and cUL Listed, Meets all UL20 requirements. Full gauge and size beveled-edge; furnished with mounting screws. Fit 1253, 1254 and 1263 flush receptacles. Standard size - 2.75" x 4.50", boxed.
Halex 64505 Conduit Elbow Arrow Hart Eagle 69-BOX Standard Wall Plate Halex 64507 Conduit Elbow
To connect EMT conduit together to allow for 45 degree bends. Fits 1257 and 1258 flush receptacles. To connect EMT conduit together to allow for 45 degree bends.
RECEPTACLE COMM LT ALMOND 20A Cooper 5270  Standard Duplex Receptacle Cooper 5270  Standard Duplex Receptacle
High impact-resistant thermoplastic face. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. .050" thick steel wrap-around mounting strap zinc-plated for corrosion resistance. Easy access split circuit break-off tab. Automatic grounding system eliminates need for bonding jumper in grounded metal enclosure. Back and side wire terminals accept #14, #12 and #10 solid or stranded wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Federal specifications WC-596. Bulk Pak. UL Listed. Meets all UL 498 and 1567 requirements. Longer, wider strap provides 40 percent more contact area. Side wire terminals accept up to #10 solid or standard copper or aluminum wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws ease installation with power screwdrivers. 15 amp, 125 volt. Bulk pack. Meets all UL 498 and 1567 requirements. Longer, wider strap provides 40 percent more contact area. Side wire terminals accept up to #10 solid or standard copper or aluminum wire. Terminal screws backed out. Combination slot/Phillips head mounting and terminal screws ease installation with power screwdrivers. 15 amp, 125 volt. Bulk pack.
Arrow Hart Eagle 68-BOX Standard Wall Plate Cooper 5221-7 Grounded Standard Toggle Switch Eagle 5221-7 Grounded Standard Toggle Switch
Standard size two gang metal wallplate for power devices using a 2.1563" single opening. Meets all UL 20 requirements. For direct connection to aluminum or copper wire. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Industrial design cam action mechanism insures quiet switch action. Side wire terminals accept up to #10 solid or stranded wire. Terminal screws are backed out-ready for wiring. Combination slot/Phillips head mounting and terminal screws. 15 amp, 120 volt. UL Listed. Meets all UL 20 requirements. For direct connection to aluminum or copper wire. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Industrial design cam action mechanism insures quiet switch action. Side wire terminals accept up to #10 solid or stranded wire. Terminal screws are backed out-ready for wiring. Combination slot/Phillips head mounting and terminal screws. 15 amp, 120 volt. UL Listed.
Carlon E990ER-CAR Access Pull Standard Radius Conduit Elbow Halex 61820B IMC Sealer Locknut Carlon UB9AG-CAR Standard Radius Conduit Elbow
Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Zenith VA1001RG6QP Type F Coaxial Adapter Zenith VA1001RG6RA Type F Coaxial Connector Cooper 827 Duplex Receptacle
Allows quick connect and disconnect of coax cable. .87" height x .5" width x .5" depth. For use in hard to reach spaces. Repositions cable jack for easy access. Plug and play. .87" height x .67" width x .37" depth. Meets all UL 498 requirements. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. 0.50" thick steel wrap-around mounting strap galvanized for corrosion resistance. Easy access split circuit break-off tab (except dual voltage). Side wire terminals accept up to #10 solid or stranded wire. Terminal screws backed out; ready for wiring. Combination slot/Phillips head mounting and terminal screws.
Cooper 827 Duplex Receptacle Cooper 827 Duplex Receptacle Thomas & Betts E986GR Type LB Rigid/IMC Conduit Body
Meets all UL 498 requirements. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. 0.50" thick steel wrap-around mounting strap galvanized for corrosion resistance. Easy access split circuit break-off tab (except dual voltage). Side wire terminals accept up to #10 solid or stranded wire. Terminal screws backed out; ready for wiring. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. 0.50" thick steel wrap-around mounting strap galvanized for corrosion resistance. Easy access split circuit break-off tab (except dual voltage). Side wire terminals accept up to #10 solid or stranded wire. Terminal screws backed out; ready for wiring. Combination slot/Phillips head mounting and terminal screws. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Cooper TWR270W Tamper Resistant Weatherproof Duplex Receptacle Cooper TWR270V Tamper Resistant Weatherproof Duplex Receptacle Cooper C1303-7V Framed Grounded Toggle Switch
Receptacle is residential grade, duplex, tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. TR and WR designations provide visual identification. UL, cULus listed. 15 amp, 125 volt. Receptacle is residential grade, duplex, tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for #14 and #12 wire, extra long and wide mounting straps and tri-combo screws that accept slotted, Phillips and Robertson-head tools. Terminal screws are backed out and ready to wire. Side-wire terminals accept up to #10 solid or stranded wire. Push in terminals accept #14 solid wire. Screw-catch feature speeds wall plate installation. TR and WR designations provide visual identification. UL, cULus listed. 15 amp, 125 volt. Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed.
Cooper 1301-7 Framed Grounded Toggle Switch AmerTac 161D Square Corner Wall Plate AmerTac 163DBR Square Corner Wall Plate
Longer, wider strap provides 40 percent more contact area to wall board. Virtually eliminates floating installations. Unbreakable top and bottom housing. Industrial design cam action mechanism insures quiet switch action. Built-in wire stripper for number 14 and number 12 wire. Built-in wire looper for pre-looping. Double riveted switch. Three way switches feature additional push-in common termination for feed-through tapping. Push-in terminals accept number 14 solid wire only. Side wire terminals accept up to number 10 solid or stranded wire. Combination slot/Phillips and Robertson-head terminal screws. 15 amp, 120 volt. Meets all UL 20 requirements. UL Listed. Traditional square corner design. With screws. 5" height x 2-7/8" width x 1/4" depth. Traditional square corner design. With screws. 5" height x 2-7/8" width x 1/4" depth.
Carlon E990DER-CAR Pull Elbow With Reducer Bushing Halex 64407 Conduit Elbow Cooper 877 Grounded Duplex Receptacle
Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Meets all UL 498 requirements. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. 0.50" thick steel wrap-around mounting strap galvanized for corrosion resistance. Easy access split circuit break-off tab (except dual voltage). Side wire terminals accept up to #10 solid or stranded wire. Terminal screws backed out; ready for wiring. Combination slot/Phillips head mounting and terminal screws.
Cooper 877 Grounded Duplex Receptacle Cooper 877 Grounded Duplex Receptacle Cooper A12 869-BOX  Duplex Receptacle
Meets all UL 498 requirements. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. 0.50" thick steel wrap-around mounting strap galvanized for corrosion resistance. Easy access split circuit break-off tab (except dual voltage). Side wire terminals accept up to #10 solid or stranded wire. Terminal screws backed out; ready for wiring. Combination slot/Phillips head mounting and terminal screws. Meets all UL 498 requirements. Triple wipe line contacts for long-term plug retention. Double wipe ground contacts for ground retention. 0.50" thick steel wrap-around mounting strap galvanized for corrosion resistance. Easy access split circuit break-off tab (except dual voltage). Side wire terminals accept up to #10 solid or stranded wire. Terminal screws backed out; ready for wiring. Combination slot/Phillips head mounting and terminal screws. Commercial specification grade straight blade receptacle on 4" galvanized steel cover. Back and side wire. 15 amp 125 volt. 5-15R NEMA. Temperature rating of -20 to 60 degrees C. UL Listed, meets all CSA requirements, NOM Certified.
Aspire 9505 Duplex Recessed Tamper Resistant Electrical Receptacle Aspire 9505 Duplex Recessed Tamper Resistant Electrical Receptacle RECEPT DUPLEX RB 15A 125V 2P3W
Receptacle is residential grade, duplex, tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. An oversized strap provides a solid base for mounting and virtually eliminates "floating" installations. Thermoplastic construction ultrasonically welded top and backbody; extra-long, extra-wide mounting straps; number 12 and number 14 push-in terminals; backwire clamps on side terminals; easy-access ground screws; built-in wire strippers. Meets all UL 498 requirements, (file no. E15058); CSA Certified, C22.2 no. 42 (file no. 6914 (6233-01); NOM Certified. Flammability rating: V2 per UL 94. temperature rating: -40 degrees C to 65 degrees C. TR designations provides visual identification. UL, cULus Listed. 15 amp, 125 volt. Receptacle is residential grade, duplex, tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. An oversized strap provides a solid base for mounting and virtually eliminates "floating" installations. Thermoplastic construction ultrasonically welded top and backbody; extra-long, extra-wide mounting straps; number 12 and number 14 push-in terminals; backwire clamps on side terminals; easy-access ground screws; built-in wire strippers. Meets all UL 498 requirements, (file no. E15058); CSA Certified, C22.2 no. 42 (file no. 6914 (6233-01); NOM Certified. Flammability rating: V2 per UL 94. temperature rating: -40 degrees C to 65 degrees C. TR designations provides visual identification. UL, cULus Listed. 15 amp, 125 volt. Receptacle is tamper resistant with a UL Listed shutter system and impact-resistant thermoplastic face and back body that is virtually unbreakable. The 2008 National Electrical Code (NEC) states that "Effective January 1, 2008, all receptacles installed in new dwelling units must be tamper-resistant." Features a wire stripper for number 14 and number 12 wire, extra long and wide mounting straps and tri-combo