Home > ELECTRICAL > SPECIALTY ELECTRICAL > BATTERIES > WATCH BATTERY/BATTERIES
Sort By:
1
Raco 8977 Electrical Box Supports Carlon B112HB Handy Box Hubbell 8660 Utility Box
Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Hubbell 8192 Outlet Box Halex 26279 Switch Box Support Hubbell 127 Octagon Box
Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. Use to suport attachment of an outlet box in drywall, paneling, etc., in the absence of a structure member. Installed in pairs. Two 1/2" and two 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Jandorf 60313 Ceiling Fan/Lamp Pull Chains BOX OCTAGON 4IN 1-1/2IN DEEP  Raco 8190 Outlet Box
Turns lamp or ceiling fan on and off. 3' braided cord with end bell and connector. Four 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Raco 8189 Ceiling Outlet Box Jandorf 60301 Fan Blade Balancing Kits Hubbell 8650 Welded Utility Box
Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Balances ceiling fan blades to reduce wobble or shaking. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed.
Jandorf 60302 Ceiling Fan Screw Assortments Hubbell 8670 Welded Utility Box Hubbell 146 Octagon Box
Used for holding ceiling fan parts in place. Contains 5 each 8/32" x 1/2" knurled head machine screws - brass plated, 8/32" x 1/2" knurled head machine screws - antique brass plated, 10/24" x 1/2" phillips pan head machine screws - brass plated and 10/24" x 1/2" phillips pan head machine screws - antique brass plated. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. 50 pound maximum recommended static load. Not designed for ceiling fan support. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Coleman 95504 Low Voltage Light Bulb Coleman 95503 Low Voltage Light Bulb Raco 662 Drawn Utility Box
Clear replacement bulb. Clear replacement bulb. Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches.
Raco 653 Utility Box Hubbell 665 Utility Box Extension Ring Raco 110 Electrical Box
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed. Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Octagon box, 3-1/2" with four 1/2" side conduit knockouts and one 1/2" bottom conduit knockout. Drawn construction, can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Hubbell 8663 Utility Box Hubbell 8232 Outlet Box Hubbell 130 Octagon Box Extension Ring
Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed. Two 1/2" and two 3/4" conduit knockouts (sides). Extension rings provide a means for adding additional cubic capacity or as and outlet box for surface conduit.
Jandorf 60318 Ceiling Fan Pull Chains Jandorf 60319 Ceiling Fan Pull Chains Bussmann Fusetron NON-15 Cartridge
Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann Fusetron NON-25 Cartridge Raco 661 Handy Box Hubbell 167 Octagon Box
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed. Two 1/2" and two 3/4" conduit knockouts (sides). Three 3/4" and two 1/2" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Allied Moulded 9318 Handy Box Zero-Mercury A76 Miniature Alkaline Battery Bussmann NON Cartridge Low Voltage Fast Acting Fuse
Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed. Designed for electronic applications which may require high rate pulses. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell LR44, Energizer A76, Panasonic L44, Panasonic LR44, Rayovac 867, Rayovac RW51, and Varta V13GA. 11.6mm diameter x 5.4mm height. 150 MAH to .9 volt. 1.5 volt, carded. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann NON Cartridge Low Voltage Fast Acting Fuse Cooper Wiring BP331NP Socket Chain Raco 674 Handy Box
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Cooper Wiring Socket Chain, Suitable For Use With: Toggle Switch Plate, NO 6 Ball, 3 ft Length, Steel, Nickel Plated, Includes: End Bell and Connector For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed.
Raco 8201 Extension Ring Outlet Box Cooper BP331BB Carded Ball Lamp Chain Raco 920 Steel Bar Hangers
For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed. Beaded, with ball diameter of 1/8" and end bell and connector. Carded. Holding prong, box clip holds box in place for nailing. Design resists bending and twisting. With stud. Length 14-1/4" thru 22-1/2". With locking tabs to hold bar in position. UL Listed.
Hubbell 8203 Electrical Box Extension Ring Jandorf 60321 Ceiling Fan Pull Chains Raco 111 Extension Ring Ceiling Outlet Box
For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. Extension rings provide a means for adding 11.8 additional cubic capacity to a box or as an outlet box for surface conduit. Not designed for ceiling fan support. Four 1/2" conduit knockouts on the sides. 50 pound maximum recommended static load. Acceptable for use in 2-hour rated walls and ceilings. 1-1/2" deep x 11.8 cubic inches. UL Listed.
Raco 175 Ceiling Outlet Box Jandorf 60315 Ceiling Fan Pull Chains Hubbell 160 Octagon Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 2-1/8" deep, 21.5 cubic inch capacity. UL Listed. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed.
Raco 112 Electrical Box Coleman 95529 Low Voltage Light Bulb BOX OCT 4IN 1-1/2DP NM CLAMP
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Octagon boxes can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls. Clear replacement bulb. With non-metallic sheathed cable clamps. With ear brackets. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 15.5 cubic inch capacity. Acceptable for use in 2-hour fire rated walls. UL Listed.
Jandorf 60316 Ceiling Fan Pull Chains Coleman 95527 Low Voltage Light Bulb Raco 8211 Outlet Box
Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. Clear replacement bulb. Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Hubbell 8257 Welded Outlet Box Jandorf 60323 Ceiling Fan Pull Chains Jandorf 60314 Ceiling Fan Pull Chains
Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length.
Energizer ECR1616BP Coin Cell Battery Coleman 95518 Low Voltage Halogen Lamp Coleman 95517 Low Voltage Halogen Lamp
Replaces all 1616 batteries. 16.0mm diameter x 1.6mm height. Lithium / Manganese Dioxide (Li/MnO2). 55 mAh (to 2.0 volts). Carded. UL Listed: MH12454. Landscape lighting clear replacement bulb. Landscape lighting T3 clear replacement bulb.
Coleman 95507 Low Voltage Halogen Lamp Coleman 95508 Low Voltage Halogen Lamp Bussmann Fusetron NON-45 Cartridge
Landscape lighting clear replacement bulb. Landscape lighting clear replacement bulb. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Jandorf 60312 Ceiling Fan Pull Chains Bussmann Fusetron NON-35 Cartridge Bussmann NON Cartridge Low Voltage Fast Acting Fuse
Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann NON Cartridge Low Voltage Fast Acting Fuse Bussmann NON Cartridge Low Voltage Fast Acting Fuse Jandorf 60304 Canopy Switch
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Jandorf Fan Switch, 1-Speed, 250 V, 3 A, Pull Chain Actuator, On-Off, 2-Wire Terminal, 122 Deg F, Brass, Standards: UL Listed
Jandorf 60303 Canopy Switch Raco 8265 Ceiling Outlet Box Jandorf 60320 Ceiling Fan Pull Chains
Jandorf Fan Switch, 3-Speed, 250 V, 3 A, Pull Chain Actuator, On-Off, 4-Wire Terminal, 122 Deg F, Black, Brass, For Affix Glass To Fixture Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length.
Jandorf 60311 Ceiling Fan Pull Chain Bussmann SC-20 Cartridge Low Voltage Time Delay Fuse Jandorf 60322 Ceiling Fan Pull Chains
Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length. High interrupting rating, current limiting. Rated at 277/480, 120/208 and 120/240 volt. UL Listed 100,000 AIR, RMS symmetrical AC (Glass G). .41 diameter fuse. Glass tube, nickel-plated brass endcaps. Beaded chain with decorative pull, for turning lamp or ceiling fan on and off. 12" length.
Energizer ECR1632BP Coin Cell Battery Jandorf 60306 Canopy Switch Energizer 2032BP-2 Coin Cell Battery
For electronics around the house, like keyless entry, electronic books and glucose monitors. Performs in extreme temperatures from -22 to 140 degrees F. Holds power for 8 years when not in use. Replacement for: BR1632, DL1632, ECR1632, KCR1632, KECR1632, KL1632, L1632. UL Listed. Jandorf Fan Switch, 3-Speed, 250 V, 3 A, Pull Chain Actuator, On-Off, 8-Wire Terminal, 122 Deg F, Black, For Replace Ceiling Fan Switches With 8 Wires Replaces Duracell DL2032, Energizer ECR2032, Panasonic CR2032, and Rayovac CR2032. 20.0mm diameter x 3.2mm height. Lithium / Manganese Dioxide (Li/MnO2). 240 mAh (to 2.0 volts). Carded. UL Listed: MH12454.
Energizer 2016BP-2 Button Cell Battery Coleman 95499 Low Voltage Halogen Lamp Coleman 11604 Low Voltage Connector
Replaces Energizer ECR2016. .08" diameter x .008" height. Lithium / Manganese Dioxide (Li/MnO2), 90 mAh (to 2.0 volts) typical capacity, 1.9 grams (0.07 oz.) typical weight. Carded. UL Listed: MH12454. Landscape lighting T3 clear replacement bulb. For connection of  low voltage cable for landscape lights.
Raco 680 Switch Box Zero-Mercury 357BPZ-3 Non-Rechargeable Electronic Coin Cell Battery Jandorf 60305 Canopy Switch
Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell D357/303, Goldpeak 357, Kodak L1154, Maxell SR44W, Panasonic SP357, Rayovac 357, Renata 357, Sony SR44W, Toshiba SR44W, and Varta V357. 11.6mm diameter x 5.4mm height. 150 MAH to 1.3 volt. Jandorf Fan Switch, 3-Way, 250 V, 3 A, Pull Chain Actuator, On-Off, 3-Wire Terminal, 122 Deg F, Brass
Toolbasix JL-SST-401183L Cable Crimper Energizer 2025BP-2 Coin Cell Battery Hubbell 683 Switch Box
Cuts and strip wires, crimps ignition terminals. Easy-to-read wire size markings. Replaces Duracell DL2025 and Rayovac CR2025. 20.0mm diameter x 2.5mm height. Lithium / Manganese Dioxide (Li/MnO2). 170 mAh to 2.0 volt. Carded. UL Listed: MH12454. Drawn construction for surface mount applications. Conduit wiring system. Eight 1/2" and four 3/4" conduit knockouts (sides). Three 1/2" and two 3/4" conduit knockouts (bottom). 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Milwaukee Clipper GS-40 Adjustable Wire Cutter/Stripper Coleman Cable 95028 Outdoor Solar Lights Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Includes spring return and lock. Adjustable, hardened spring steel. Strips 10-24 gauge wire. Powered by the sun, no wiring required. Durable plastic construction. White LED provides downlighting effect. Installs with included screws. Rechargeable NiCd battery included. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Gardner Bender GTPS-3100 Cable Stripper GB CR-1000 Cable Ripper
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Strips UTP and STP cable up to .24" (6.2mm) OD. Tension release lever, compact design. For use on CAT 3 and CAT 5 cable. Carded. GB Cable Ripper, Premium, 14 - 6 AWG Cable/Wire, 4 in Overall Length, cULus Listed, For Use to Cut Off Cable Jacket
Raco 509 Old Work Switch Box Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Conduit wiring system. Gangable switch box offers the option of constructing a box to hold two or more devices. Adjustable plaster ears allow box to be used in old work applications. Provided old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Two 1/2" bottom knockouts and two 1/2" end knockouts. 2-1/2" deep - 12.5 cubic inches. UL Listed. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Y-ADAPTER ACCESSORY           Cooper Wiring NO.263 Fuse Reducer Gardner Bender GS-386 Diagonal Cutting Plier
Y-ADAPTER ACCESSORY
Our Price: $7.92
Y-Adaptor accessory allows 2 low voltage heads to be connected at 1 quick connect location. Fuse reducers allow a smaller size fuse to be installed in a fuse block intended for a larger fuse. A No.263 reducer installed on a 30 amp fuse permits it to be installed in a 60 amp fuse block. Reducers are particularly useful when equipment is being converted. Proper protection can be maintained without the expense of replacing the fuse block. Tapered nose allows cutting in tight locations. Dual cutting edge and high-leverage comfort grip handle design for optimal cutting performance. Precision-machined and induction-hardened knives strengthen cutters and provide consistent performance when cutting aluminum, copper and medium-hard steel wire.
Bussmann Fusetron NON-100 Cartridge EXTENSION CORD ACCESSORY 10FT Bussmann Fusetron NON-100 Cartridge
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Extension cord accessory for system lead. 10 Ft. Increases the gap between the transformer and the low voltage heads. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Gardner Bender GS-366 Cable Crimper/Stripper FUSE FNM MIDGET T-DELAY 20AMP FUSE FNM MIDGET T-DELAY 30AMP
Strips cable, 10-22 AWG wire, crimps terminals and cuts bolts. Easy-to-read wire size markings. Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2". Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2".
FUSE FNM MIDGET T-DELAY 10AMP Bussmann FNM-15 Cartridge Low Voltage Midget Time Delay Fuse Westinghouse 7703700 Smooth Ceiling Medallion
Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2". Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2". Lightweight, durable, easy-to-install. Use above the canopy of a ceiling fan to add a decorative element. Install unfinished or finished in a number of ways including painting or staining.
Gardner Bender GS-385 Multi-Function Long Nose Plier Westinghouse Lighting 7702700 Ceiling Medallions Mintcraft CP-C8153L Multi Function Wire Stripper
Multi-function long nose pliers cut, strip and crimp. Use needle nose to form wire or grip small parts. Strips number 14 - number 16 AWG solid or stranded wire. Crimps insulated terminals up to number 10 AWG. Cuts solid or stranded wire. Serrated jaw and cushioned grips. Lightweight, durable, easy-to-install. Use above the canopy of a ceiling fan to add a decorative element. Install unfinished or finished in a number of ways including painting or staining. Center opening 4.5". Rust-resistant steel with cushioned vinyl grip. Easy-to-read wire size markings.
Bussmann Edison ECSR30 Time Delay Fuse Gardner Bender GS-45 Adjustable Wire Cutter/Stripper FUSE MIDGET 15 AMP
Same size as ordinary fuses. 10 second minimum time lag at 500 percent rated current prevents shutdowns caused by starting currents or other harmless overloads. Guards motor against burnout from overloads or single phasing. Operates cooler than other fuse types, reduces heating in switches and panels. 13/16" diameter x 5" length. Class RK5, 600 volt maximum. UL Listed, CSA Certified. Strips solid or stranded wire. Compact, adjusts to eight wire sizes. Hardened spring steel. Looping hole bends, loops wire for termination on screws. Also includes spring return for easy handling. High interrupting rating, current limiting. Rated at 277/480, 120/208 and 120/240 volt. UL Listed 100,000 AIR, RMS symmetrical AC (Glass G). .41 diameter fuse. Glass tube, nickel-plated brass endcaps.
Gardner Bender TT-10B Electrician 3-In-1 Tapping and Rethreading Tool FUSE MIDGET 20 AMP            FUSE FNM MIDGET TIMEDELAY 5AMP
Top grade Rockwell 60 steel. Fits tap sizes 6-32, 8-32 and 10-24. Unclogs screw holes, retaps stripped holes. High interrupting rating, current limiting. Rated at 277/480, 120/208 and 120/240 volt. UL Listed 100,000 AIR, RMS symmetrical AC (Glass G). .41 diameter fuse. Glass tube, nickel-plated brass endcaps. Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2".
Bussmann SC-30 Cartridge Low Voltage Time Delay Fuse POST CAP FENCE SLR W/ADPTR WHT POST CAP FENCE SLR W/ADPTR BRZ
High interrupting rating, current limiting. Rated at 277/480, 120/208 and 120/240 volt. UL Listed 100,000 AIR, RMS symmetrical AC (Glass G). .41 diameter fuse. Glass tube, nickel-plated brass endcaps. Solar Fence Post Cap, with Adapter Solar Fence Post Cap, with Adapter
POST CAP FENCE SLR W/ADPT BLK Bussmann Fusetron NOS Cartridge Bussmann SC-25 Auto Cartridge Low Voltage Time Delay Fuse
Solar Fence Post Cap, with Adapter General-purpose application. Non-current limiting. 600 volt maximum. High interrupting rating, current limiting. Rated at 277/480, 120/208 and 120/240 volt. UL Listed 100,000 AIR, RMS symmetrical AC (Glass G). .41 diameter fuse. Glass tube, nickel-plated brass endcaps.
Gardner Bender GS-389 Cable Cutter/Crimper Gardner Bender GS-89 Cable Cutter/Crimper FUSE FNM MIDGET T-DELAY 12AMP
For high-leverage. Cuts up to 3/8" diameter cable. Crimps RG-58, RG-59 and RG-6 F-style connecters. Cushioned grips. For high-leverage. Cuts up to 3/8" diameter cable. Crimps RG-58, RG-59 and RG-6 F-style connecters. Cushioned grips. Provides supplemental protection to industrial, commercial, agricultural, heating, ventilating and air conditioning equipment. Used to protect internal components such as control circuit wiring, motor control transformers and small motors. 250 volt maximum, 13/32" x 1-1/2".
BOX 3GANG 1-5/8DEEP 1/2-3/4 KO Calterm 66212 Streamline Wire Stripper Bussmann Fusetron NON-30 Cartridge
Used where a number of wiring devices are to be centrally located. Features 1/2" and 3/4" concentric knockouts for use with a wide variety wiring methods. 1-5/8" x 4.5" x 8.63". UL Listed. Cushion grip wire handles. Strips and cuts. Plier nose for pulling and looping wire. Spring return and safety lock. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann Fusetron NON-25 Cartridge Gardner Bender GS-355 Wire Stripper Bussmann Fusetron NON-20 Cartridge
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Strips solid or stranded wire 10 - 20 AWG. Precision stripping stations. Laser-etched markings. Pliers nose and curved cutting blade aid in pulling and cutting wire. Spring-loaded action returns handles to open position. Curved high-leverage handles for added comfort. Looping hole forms wire to fit on screw terminal. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann Fusetron NON-15 Cartridge Gardner Bender GS-360 Wire Stripper with Lock Bussmann NON-EK Emergency Non-Cartridge Fuse Kit
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. Strips solid or stranded wire. Laser-etched markings. Pliers nose and curved cutting blade aid in pulling and cutting wire. Power spring return reduces hand fatigue. Looping hole forms wire to fit on screw terminal.  Wire gauge #10 - #20 AWG. NON fuses with fuse tester. Contains one NON-20, two NON-30, one NON-40, two NON-60, and a fuse tester.
Hunter Fan 26019 Ceiling Fan Downrod Hunter Fan 25136 Ceiling Fan Downrod Gardner Bender PDTL-3110 Non-Impact Punch Down Tool
Provides stability and wobble-free performance. 3/4" diameter pipe. Provides stability and wobble-free performance. 3/4" diameter pipe. Non-impact punch-down, non-cut 110-style blade used in CAT 3 and CAT 5 terminations.
Klein Tools 11045 Wire Cutter/Stripper FUSE TIME DELAY CART 10 AMP   Channellock 958 Wire Cutter/Stripper
Wire gauge markings on both sides, cuts, strips, and loops wire. Wide handles with cushion ridges designed for comfort. Spring-loaded action returns handles to open position. Narrow nose fits into tight places. Made of hardened steel with precision-ground stripping holes. Black oxide finish. No. 11045 strips solid wire AWG. No. 11046 strips stranded wire. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Strips insulation, with no damage to wire. Cuts copper wire cleanly. Scissor type blades are precision ground. Lean plier nose pulls, loops wire ends. Highly visible AWG and mm wire gauge sizes embossed in the metal. Comfort grips.
Amertac VM1001RG6ST Cable Stripper Klein 74007 Adjustable Wire Stripper Klein Tools 11046 Wire Cutter/Stripper
Strips insulation from coax cable. 3.87" height x 1.25" width x .75" depth. Adjusts from 12 - 24 AWG (2.5 - .25 mm?). Gets into tight areas. Wire gauge dial sets stripping dies to proper size, helps prevent nicked wire. Spring-loaded design opens automatically after each action. Yellow handle, 5-1/2" length. Wire gauge markings on both sides, cuts, strips, and loops wire. Wide handles with cushion ridges designed for comfort. Spring-loaded action returns handles to open position. Narrow nose fits into tight places. Made of hardened steel with precision-ground stripping holes. Black oxide finish. No. 11045 strips solid wire AWG. No. 11046 strips stranded wire.
Coleman 95757 Low Voltage Recessed Deck Light Gardner Bender GS-359 Cable Stripper Zero-Mercury 371BPZ Battery
Accent light for use on decks and stairways. 10 watt bulb included. Uses replacement bulb # 95527. Cuts and strips RG-59 and RG-6 coaxial cable, multiple size stripping stations strip both the outer jacket and inner conductor. Can be used with both standard and quad shield cable. Hex shaped slot helps push "F" connectors on to cable. Curved cutting blade, spring return. Replaces 370, SR920SW/W, TR920SW. 9.5mm diameter x 2.1mm height. 34 MAH to 1.3 volt. 1.55 volt, carded.
Bussmann Fusetron FRNR-40 Cartridge Current Limiting Low Voltage Cooper Bussmann Fusetron FRN-R Non-Indicating Time Delay Fuse Fusetron FRN-R Cartridge Low Voltage Time Delay Fuse
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Cooper Bussmann Time Delay Fuse, Energy Efficient, Non-Indicating, Series: Fusetron, FRN-R, 50 A, 250 VAC/125 VDC, 200 kA at 250 VAC, 20 kA at 125 VDC Interrupt, Class: RK5, 10 sec at 500% Response, Ferrule, Cylindrical, Rejection Body, Dual Element, Fiberglass, 13/16 in Diameter, 3 in Length, Fuse Holder Code: K, CE, CSA Certified, UL Listed Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Fusetron FRN-R Cartridge Low Voltage Time Delay Fuse Bussmann Fusetron FRNR-60 Cartridge Current Limiting Low Voltage Zero-Mercury 395BPZ Non-Rechargeable Electronic Battery
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Designed for use on continuous low drain. Replaces 399, SR27SW/W, TR927W; Duracell D395, Maxell SR927SW, Panasonic SP395, Sony SR927SW, Timex LA, Toshiba SR927SW, and Varta V395. 9.5mm diameter x 2.7mm height. 52 MAH to 1.3 volt. 1.55 volt, carded.
Zero-Mercury 389BPZ Battery Fusetron FRN-R Cartridge Low Voltage Time Delay Fuse Bussmann Fusetron FRN-R-15 Cartridge Current Limiting Low Voltage
Designed for use on continuous low drain. Replaces 390, 189, LR1130, SR1130SW/W; Duracell D389, D391, and D393; Maxell SR1130W; Panasonic SP389; Sony SR1130W; Toshiba SR1130W; and Varta V389. 11.6mm diameter x 3.0mm height. 85 MAH to 1.3 volt. 1.55 volt, carded. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified.
Bussmann Fusetron FRN-R-25 Cartridge Current Limiting Low Voltage Gardner Bender GS-370 Multi Tool Wire Stripper Gardner Bender GS-359D Cable Cutter/Stripper
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Curved cutting blade, strips and cuts copper and aluminum wire, solid or stranded, 10-22 AWG. Precision ground-stripping stations prevent nicking conductor while stripping. Cuts and rethreads bolt sizes 4-40, 5-40, 6-32, 8-32, 10-24 and 10-32. Pliers nose for pulling and looping wire. Crimps insulated and non-insulated terminals. Crimps coaxial F connectors. Curved blade cuts and strips RG-59 and RG-6 coaxial cable. Can be used with both standard and quad shield cable. Multiple size stripping stations strip both the outer jacket and inner conductor. Hex-shaped slot helps push "F" connectors onto cable.
Gardner Bender GS-394 Wire Crimper/Stripper Zero-Mercury 377BPZ Non-Rechargeable Battery Zero-Mercury 364BPZ Button Cell Battery
Automatic action jaw-loaded stripper grips insulation, strips and cuts solid or stranded 10 to 24 AWG wire cleanly, with one squeeze. Crimps insulated, non-insulated terminals and auto 7-8 mm ignition terminals. Metric and AWG. Strips 10-26 gauge wire. Replaces 376, SR626SW/W, TR626W; Duracell 377 and D377, Energizer 377, Maxell SR626SW, Panasonic SP377, Renata 377, Sony SR626SW, Timex BA, Toshiba SR626SW, and Varta V377. 6.8mm diameter x 2.6mm height. 26 MAH to 1.3 volt. 1.55 volt, carded. Replaces SR/TR621SW; Duracell D364, Maxell SR621SW, Panasonic SP364, Sony SR621SW, Toshiba SR621SW, and Varta V364. 6.8mm diameter x 2.15mm height. 1.55 volt, carded.
Zero-Mercury 392BPZ Battery Zero-Mercury 379BPZ Battery King Safety 46515 Wire Stripper with Handle Lock
Designed for use on continuous low drain. Replaces LR41, 192, 384, SR41SW/W; Duracell D392, Energizer 392, Goldpeak 392, Maxell SR41W, Panasonic SP392, Rayovac 392, Renata 392, Sony SR41W, Timex K, Toshiba SR41W, and Varta V392. 7.9mm diameter x 3.6mm height. 41 MAH to 1.3 volt. 1.55 volt, carded. Designed for use on continuous low drain. Replaces SR521SW/W, TR521W; Duracell D301, D350, D357, D361, D364, D366, D371, D377, D381, D384, D386, D389, D390, D391, D392, D393, D394, D395, D396, D397, D399, DL2016; Energizer 379; Goldpeak 379; Maxell SR521SW; Rayovac 379, RW30, RW311, RW313, RW315, RW317, RW320, RW329, RW33, RW36, RW37, RW40, RW410, RW411, RW413, RW42, RW44, RW442, RW47, RW48, RW49; Renata 379; Sony SR521SW; Timex JA; Toshiba SR521SW; and Varta V379. 5.8mm diameter x 2.15mm height. 14.5 MAH to 1.3 volt. 1.55 volt, carded. Plier nose for pulling and looping wire. Scissor-type cutting blade. Ergonomic-shaped handles. Cuts and strips both solid and stranded wire. Spring automatically spreads handles. Slide lock. Wire sizes embossed in metal. Dimensions 6"/152 mm, minimum/maximum strip AWG 20-10, 0.8-2.6 mm.
Vise Grip 2078309 Multi-Tool Cable Stripper/Crimper/Cutter Gardner Bender GS-361 Wire Stripper Westinghouse Victorian 7702800 Ceiling Medallion
Multi-tool strips and cuts wire from 10-22 AWG. Pliers style nose allows pulling and looping wire. Bolt cutter leaves perfect lead thread. Induction hardened cutting edge. Wire crimper for insulated and non-insulated terminals. Meets or exceeds all ANSI standards. Strips solid or stranded wire. Laser-etched markings. Pliers nose and curved cutting blade for pulling and cutting wire. Power spring return reduces hand fatigue. Deluxe cushion grip. Looping hole forms wire to fit on screw terminal. Wire gauge number 16 - 30 AWG. 6-1/4" total length. Lightweight, durable, easy-to-install. Use above the canopy of a ceiling fan to add a decorative element. Install unfinished or finished in a number of ways including painting or staining. Center opening 4.5".
Fusetron FRN-R Cartridge Low Voltage Time Delay Fuse Gardner Bender GK-15N Crimper/Stripper Kit Bussmann Fusetron NON-200 Cartridge
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the ampere rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Kit includes sleek multi-use stripper-crimper, 100 assorted insulated terminals in a convenient 11 compartment reclosable storage and carrying case. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Gardner Bender GCP-3400 High Leverage Linemans Crimping Tool Bussmann Fusetron FRNR-30ID Cartridge Current Limiting Low Voltage Bussmann Fusetron FRNR-20ID Cartridge Current Limiting Low Voltage
High-leverage tool with comfort grip handles, crimping die and side cutters. UL approved when used with GB #310, 410, and 411 crimp connectors for permanent connections. Fusetron dual element time-delay current limiting class RK5 fuse 250 volt maximum. Drop-in replacement upgrade for one-time and renewable fuses to aid in locating the open fuse when the power goes out. Time-delay - 10 seconds (minimum) at 500 percent rated current. Indicator on the side turns black when the fuse opens. Fits existing RK1, RK5, K5 H 30 and 60 amp fuse blocks and holders. UL Listed. Fusetron dual element time-delay current limiting class RK5 fuse 250 volt maximum. Drop-in replacement upgrade for one-time and renewable fuses to aid in locating the open fuse when the power goes out. Time-delay - 10 seconds (minimum) at 500 percent rated current. Indicator on the side turns black when the fuse opens. Fits existing RK1, RK5, K5 H 30 and 60 amp fuse blocks and holders. UL Listed.
King Safety 46522 UP Front Wire Crimper/Stripper Channellock 957 Wire Stripper Klein-Kurve Romex GRX-3224 Dual Cable Stripper
Wire sizes embossed in metal. Anvil-type wire cutter. Bolt cutting capabilities. Air pocket cushioned grip. Weight 8 oz/227g, dimensions 7.5"/190mm, minimum/maximum AWG 22-10, crimps AWG insulated/non-insulated 22-10/12-10, bolt cutter insulated 4-40/6-32/8-32/10-32/10-24. Designed to cut copper wire. Precision holes for wire stripping. Lean plier nose pulls and loops wire. Scissor-type blades are precision ground and heat treated to hold their edge. Highly visible AWG solid and AWG stranded wire gauge sizes embossed in the metal. Comfort grips. Strips AWG solid wire sizes: 10, 12, 14, 16, and 18 and strips AWG strainded wire sizes: 12, 14, 16, 18, and 20. Strips outer sheath of 12/2 or 14/2 cable, strips single conductor 12 or 14 AWG. Cuts and rethreads bolt sizes 6-32 and 8-32. Curved cutting blade, pliers nose, wire looping hole. Locking handle and power spring return.
Gardner Bender GPS-3228 Diagonal Cutting Plier Mintcraft SE-923L Wire Stripper Bussmann Fusetron FRNR-40ID Cartridge Current Limiting Low Voltage
Angled head allows cutting in tight locations. Dual cutting edge and high-leverage flared handle design for optimum gripping and cutting performance. Precision machined and induction hardened knives strengthen cutters and provide consistent performance when cutting aluminum, copper and medium-hard steel wire. Automatic action stripper grips wire, cuts insulation cleanly, and strips solid or stranded wire with one squeeze. AWG size clearly marked at each cutting station. Adjustable guide provides consistent, uniform strip length. Fusetron dual element time-delay current limiting class RK5 fuse 250 volt maximum. Drop-in replacement upgrade for one-time and renewable fuses to aid in locating the open fuse when the power goes out. Time-delay - 10 seconds (minimum) at 500 percent rated current. Indicator on the side turns black when the fuse opens. Fits existing RK1, RK5, K5 H 30 and 60 amp fuse blocks and holders. UL Listed.
Bussmann Fusetron FRNR-60ID Cartridge Current Limiting Low Voltage Channellock 908 Wire Stripper Mintcraft KY-665T3L Wire Stripper
Fusetron dual element time-delay current limiting class RK5 fuse 250 volt maximum. Drop-in replacement upgrade for one-time and renewable fuses to aid in locating the open fuse when the power goes out. Time-delay - 10 seconds (minimum) at 500 percent rated current. Indicator on the side turns black when the fuse opens. Fits existing RK1, RK5, K5 H 30 and 60 amp fuse blocks and holders. UL Listed. Strips wire without damage to conductor. Cuts AWG 10-22 wire, bolts 10-24, 6-32, 8-32, 10-32 and 4-40. Crimps coax cable and 7-8 mm ignition cables. Channellock blue comfort grips.Easy-to-read wire size markings. Crimps both insulated and non-insulated wire. Strips 10-24 AWG copper or aluminum wire, solid or stranded, cuts wire (HRC 40-50), crimps 10-22 AWG insulated, 4-22 AWG non-insulated and 7-8mm ignition terminals. Micro adjustable knob allows wire smaller than 24 AWG to be stripped. Easy-to-read wire size markings.
Klein Tools 2100-7 Electrician Scissor Hunter Fan 26041 Ceiling Fan Downrod Hunter Fan 26020 Ceiling Fan Downrod
For telecom and electrical applications. Strong, tough tempered steel with nickel-plated finish. Upper blade has notches for stripping 19 AWG and 23 AWG wire. Scraper and file on outside of both blades. Serrated lower blade reduces slippage. 5-1/4'' length, .20 pounds. Provides stability and wobble-free performance. 3/4" diameter pipe. Provides stability and wobble-free performance. 3/4" diameter pipe.
Gardner Bender GRX-122 Cable Stripper Strip-Easy SE SE-92 Adjustable Wire Stripper FUSE T-DELAY CART EASY ID 15A
Strips outer sheathing of NM cable. Pliers nose, curved cutting blade, curved spring action handles with air pocket cushion grips, wire looping holes. Laser etched markings for high visibility. Handles 12/2 NM cable and 12 AWG single conductor wire. Automatic action, grips wire, cuts insulation cleanly, and strips solid or stranded wire with one squeeze. 8 to 22 AWG. Fusetron dual element time-delay current limiting class RK5 fuse 250 volt maximum. Drop-in replacement upgrade for one-time and renewable fuses to aid in locating the open fuse when the power goes out. Time-delay - 10 seconds (minimum) at 500 percent rated current. Indicator on the side turns black when the fuse opens. Fits existing RK1, RK5, K5 H 30 and 60 amp fuse blocks and holders. UL Listed.
Bussmann Fusetron FRN-R Cartridge Current Limiting Low Voltage Bussmann Fusetron FRN-R-100 Cartridge Current Limiting Low Voltage Hunter Fan 26021 Ceiling Fan Downrod
Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the amp rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides motor overload, ground fault and short-circuit protection. Helps protect motors against burnout from overloads and single phasing on three phase systems. Will hold an overload which is five times greater than the amp rating of the fuse for a minimum of ten seconds. 250 volt maximum. UL Listed, CSA Certified. Provides stability and wobble-free performance. 3/4" diameter pipe.
Hunter Fan 25138 Ceiling Fan Downrod Coleman Cable 91241 Inglenook Outdoor Solar Lights Gardner Bender EFT-50B Economy Fish Tape
Provides stability and wobble-free performance. 3/4" diameter pipe. Powered by the sun, no wiring required. Plastic frame construction, stained glass lens. Warm white LED never needs replacing. Wide angle beam. Installs in minutes with included screws. Will fit standard size 4" x 4" wooden fence posts. Rechargeable batteries included. Standard steel tape. View port in reel to view amount of tape used. Reel diameter 7". 50' x 1/8 x .045".
Gardner Bender PDB-66110 Combination Punch Down Blade Coleman 09501 Low Voltage Electrical Cable Bussmann Fusetron NON-60 Cartridge
Cut Style blade, 110-style used in CAT 3 and CAT 5 terminations (Cut), 66-style used to terminate phone wiring (Cut). For use with outdoor low voltage lighting systems operating at 30 volts or less. Put light fixtures where you want or expand a set. UL Listed. Made in the USA. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Bussmann Fusetron NON-50 Cartridge Bussmann Fusetron NON-40 Cartridge Bussmann Fusetron NON-35 Cartridge
For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed. For general purpose circuits, protects lighting, heating and other circuits not subject to temporary surges and where available short-circuit currents are relatively low. Does not have any appreciable degree of time delay and should not be specified in circuits where large transients or motor overloads occur. Single element type. The counterpart of type W plug fuses. Use in non-motor circuits. 50,000 AIR. 250 volt maximum. UL Listed.
Gardner Bender SE SE-398 Cable Cutter/Stripper BigBen BH-75 Conduit Bender Handle Energizer ECR2025BP Non-Rechargeable Coin Cell Battery
Cuts and strips RG-58, RG-59, RG-6, and RG-6 quad coaxial cable. Adjusts to various cable thickness. Pre-threaded for easy assembly and labeled with an informative guide for efficient conduit bending. Fits aluminum bender numbers 910, 911, 930, 931, 940, 941; iron bender numbers 920, and 921. Replaces Duracell DL2025 and Rayovac CR2025. 20.0mm diameter x 2.5mm height. Lithium / Manganese Dioxide (Li/MnO2). 170 mAh to 2.0 volt. Carded. UL Listed: MH12454.
Energizer ECR2032BP Non-Rechargeable Coin Cell Battery Energizer ECR2016BP Non-Rechargeable Coin Cell Battery Zero-Mercury 357BPZ Non-Rechargeable Electronic Coin Cell Battery
Replaces Duracell DL2032, Energizer ECR2032, Panasonic CR2032, and Rayovac CR2032. 20.0mm diameter x 3.2mm height. Lithium / Manganese Dioxide (Li/MnO2). 240 mAh (to 2.0 volts). Carded. UL Listed: MH12454. Replaces Energizer ECR2016. .08" diameter x .008" height. Lithium / Manganese Dioxide (Li/MnO2), 90 mAh (to 2.0 volts) typical capacity, 1.9 grams (0.07 oz.) typical weight. Carded. UL Listed: MH12454. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell D357/303, Goldpeak 357, Kodak L1154, Maxell SR44W, Panasonic SP357, Rayovac 357, Renata 357, Sony SR44W, Toshiba SR44W, and Varta V357. 11.6mm diameter x 5.4mm height. 150 MAH to 1.3 volt.
Hunter Fan 26042 Ceiling Fan Downrods Gardner Bender SE SE-98 Adjustable Cable Cutter/Stripper Channellock 909 Crimping Plier