Home > ELECTRICAL > SPECIALTY ELECTRICAL > BATTERIES
Choose a sub category:
AAA BATTERY/BATTERIES OUTLET BOXES OUTLET BOXES
AA BATTERY/BATTERIES PVC SWITCH BOXES PVC SWITCH BOXES
C BATTERY/BATTERIES UTILITY BOXES UTILITY BOXES
D BATTERY/BATTERIES OCTAGON BOXES OCTAGON BOXES
9 VOLT BATTERY/BATTERIES CEILING BOXES CEILING BOXES
6 VOLT BATTERY/BATTERIES BOX COVERS BOX COVERS
ELEC BOX SUPPORTS ELEC BOX SUPPORTS WATCH BATTERY/BATTERIES
SPECIALTY BATTERY/BATTERIES SPECIALTY BOXES SPECIALTY BOXES
RECHARGEABLE BATTERY/BATTERIES BATTERY CHARGERS
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Hubbell 860 Raised Blank Utility Box Cover Hubbell 864 Utility Box Cover Hubbell 865 Utility Box Cover
Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 8752 Square Flat Blank Electrical Box Cover Hubbell 722 Octagon Flat Blank Electrical Box Cover Carlon HB1BL Blank Handy Box Cover
Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed.
Carlon HB1GF Handy Outlet Box Cover Carlon HB1SW Handy Box Cover Carlon HB1DP Handy Box Cover
Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed.
Thomas & Betts BH122A-UPC Outlet Box Hubbell 863 Utility Box Cover Hubbell 861 Utility Box Cover
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 8753 Square Flat Electrical Box Cover Hubbell 724 Octagon Flat Electrical Box Cover Thomas & Betts B114R-UPC Switch Box
Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed. Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed.
Thomas & Betts B232A-UPC Outlet Box Hubbell 8772 Square Raised Device Box Cover Hubbell 703 Round Flat Ceiling Pan Cover
New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Carlon E460R-CAR Blank Round Outlet Box Cover Duracell PX76A675PK Non-Rechargeable Cylindrical Alkaline Battery Carlon A400R-CAR Square Blank Electrical Box Cover
High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed. Lasts longer in electronic devices. Two gang blank rise. Carlon blue color.
Raco 8768 Mud-Ring Raised Square Electrical Box Cover Carlon A420RR Raised Tubing Electrical Box Cover Thomas & Betts B108B-UPC Outlet Box
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Suitable for paneling masonry, plaster, sheetrock, tile and all wall coverings. Brilliant electric blue. UL Listed. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed.
Carlon A410R-CAR Square Electrical Box Cover Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box
Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed. Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4".
Hubbell 127 Octagon Box Raco 787 Mud-Ring Flat Square Electrical Box Cover Allied Moulded 1098-N Switch Box
Two 1/2" and two 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Steel box cover, used to mount switch or receptacle. UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
Raco 8756 Raised Square Open Electrical Box Cover Raco 871 Wall Plate BOX OCTAGON 4IN 1-1/2IN DEEP
Raised device cover. Used to hang light fixture from 4" square box. Not designed for ceiling fan support. Angled mounting slots allow for correction of box misalignment. Raised 5/8" - ears 2-3/4" - 4 cubic inches. UL Listed. UPC bar coded. Two device switch box cover. Made from unpainted, pregalvanized steel. Used with  2 toggle 2 gang switch boxes. UL 514-A Listed, File E195978 / CSA Listed, File LR-1082. Four 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Carlon A471RR Round Tubing Ceiling Box Extender with Round Cover Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box
Half inch raised round high impact lightweight PVC. Used with nonmetallic sheathed cable in octagon boxes. Supports 50 pounds. UL Listed. Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05".
Hubbell 731 Octagon Flat Electrical Box Cover Raco 727 Raised Octagon Open Electrical Box Cover Raco 832 Blank Flat Square Electrical Box Cover
Steel box cover for one duplex receptacle. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Used to hang light fixture from 4" octagon box or 4" round ceiling pan. Not designed for ceiling fan support. Key-hole mounting feature allows for installation of cover without removing box screws. Raised 5/8" - 3.8 cubic inch capacity. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. 4-11/16" square. UL Listed.
Raco 7887RAC Old Work Cable Box Raco 791 Mud-Ring Flat Square Electrical Box Cover Hubbell 8778 Square Raised Device Box Cover
Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed. Steel box cover, 4", used to mount two switches or receptacles. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Allied Moulded 1099-N Switch Box MUD RING 4SQ SINGLE RAISED 3/4 Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Raco 8769 Mud-Ring Raised Square Electrical Box Cover Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Raco 8196 Electrical Box
Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed.
Hubbell 907C Square Exposed Work Cover Thomas & Betts B120R Outlet Box Hubbell 146 Octagon Box
Used to mount two duplex receptacles on a box in surface mount application. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. 50 pound maximum recommended static load. Not designed for ceiling fan support. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Coleman 95504 Low Voltage Light Bulb Coleman 95503 Low Voltage Light Bulb Raco 729 Flat Octagon Electrical Box Cover
Clear replacement bulb. Clear replacement bulb. Steel box cover for single toggle switch. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Raco 8197 Welded Electrical Box Duracell MN27BPK Alkaline Battery Thomas & Betts BH235A Outlet Box
Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed. Used mainly for security applications such as car remotes. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall.
Carlon A521DE ENT Flexible Raceway Outlet Box Hubbell 902C Square Raised Exposed Work Cover Raco 8779 Mud-Ring Raised Square Electrical Box Cover
Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed. For one duplex receptacle. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Carlon SC100A 1-Gang Low Voltage Mounting Bracket Raco 110 Electrical Box Hubbell 833 Square Flat Electrical Box Cover
Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". Octagon box, 3-1/2" with four 1/2" side conduit knockouts and one 1/2" bottom conduit knockout. Drawn construction, can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Steel box cover with single 1/2" knockout in the center. 4-11/16" square. UL Listed.
Hubbell 803C Square Exposed Work Cover Raco 800C Raised Square Exposed Work Cover Raco 473 Gangable Switch Box
Raised 1/2". For two toggle switches. 6-1/2 cubic inch capacity. UL Listed. Used to mount one toggle switch on box in surface mount applications. Raised 1/2". 6-1/2 cubic inch capacity. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed.
Carlon E980CN-CAR Blank Weatherproof Cover Raco 915C Raised Square Exposed Work Cover Raco 809C Raised Square Exposed Work Cover
Fits Carlon single gang FS boxes. Paintable surface with textured finish to hide scratches. Stainless steel mounting screws and gasket included. UL, CSA Listed. For one GFCI receptacle and one duplex receptacle. 6.5 cubic inch capacity. UL Listed, CSA Listed. For two GFCI receptacles. 6.5 cubic inch capacity. UL Listed, CSA Listed.
Hubbell 130 Octagon Box Extension Ring Raco 906C Surface Mount Exposed Work Cover Carlon SC200RR Low Voltage Old Work Bracket
Two 1/2" and two 3/4" conduit knockouts (sides). Extension rings provide a means for adding additional cubic capacity or as and outlet box for surface conduit. For one each duplex receptacle and toggle switch. 4" square. Raised 1/2". 6.5 cubic inch capacity. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed.
Raco 528 Gangable Switch Box Hubbell 8500 Gangable Switch Box Carlon B418A-UPC Shallow Outlet Box
Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Thomas & Betts B225R-UPC Outlet Box Eveready 1250 Non-Rechargeable Electronic Battery Eveready 1235 Non-Rechargeable Super Battery
With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16" Carbon-Zinc. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carbon-Zinc. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F.
Raco 400 Gangable Switch Box Thomas & Betts B121ADJ Wall Box Thomas & Betts B344AB-UPC Outlet Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Carlon CPC4WH Blank Round Flat Outlet Box Cover Hubbell 519 Gangable Switch Box Hubbell 8531 Gangable Switch Box
Non-metallic white ceiling box cover, flat and blank. 4" diameter. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed.
Raco 404 Non-Gangable Shallow Switch Box Raco 808C Raised Square Exposed Work Cover Hubbell 471 Gangable Switch Box
Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Raised 1/2". Used to support switches or receptacles independent of the box (box must still be used). 6.5 cubic inches. UL Listed. Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed.
Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box Hubbell 167 Octagon Box
Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. Two 1/2" and two 3/4" conduit knockouts (sides). Three 3/4" and two 1/2" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Zero-Mercury A76 Miniature Alkaline Battery Raco 420 Gangable Switch Box Eveready 1222 Non-Rechargeable Super Battery
Designed for electronic applications which may require high rate pulses. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell LR44, Energizer A76, Panasonic L44, Panasonic LR44, Rayovac 867, Rayovac RW51, and Varta V13GA. 11.6mm diameter x 5.4mm height. 150 MAH to .9 volt. 1.5 volt, carded. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. Carbon Zinc, metal jacket, 25 mA continuous drain at rated capacity. Operating temperature 20 to 130 degrees F. Carded.
Raco 810C Raised Square Exposed Work Cover Raco 560 Gangable Switch Box Jandorf 60492 Lampholder Fixture Socket
Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle, 2.141" diameter. 6-1/2 cubic inch capacity. 4" square. UL Listed. For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed. Jandorf Lamp Socket, 660 W Lamp, 600 V, Fluorescent Lamp, Medium Bi-Pin Base
Raco 8355 Non-Gangable Switch Box Energizer E91BP-2 Non-Rechargeable Alkaline Battery Energizer E92BP-2 Non-Rechargeable Alkaline Battery
Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Raco 7488RAC Old Work Cable Box Allied Moulded 9363-EWK Old Work Switch Box Carlon E365C-CAR Blank Round Weatherproof Cover
Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Round non-metallic gray weatherproof cover. Fits T boxes.
Raco 567 Gangable Switch Box Arrow Hart 2507W-BOX Slimline Lampholder Thomas & Betts B432A-UPC Outlet Box
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. White slimline lampholders. For replacement use in fluorescent lighting fixtures as well as enclosed outdoor signs. Molded of white thermoset plastic for appearance and durability. UL Listed. Temperature rating of -40 to 65 degrees C. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Raco 976 Extension Ring Switch Box Duracell DL2450BPK Coin Cell Battery Jandorf 60496 Lampholder Fixture Socket
Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. Primary usage is for keyless entry. Lasts longer than alkaline. Jandorf Lamp Socket, 660 W Lamp, 600 V, Fluorescent Lamp, Medium Bi-Pin Base
Raco 111 Extension Ring Ceiling Outlet Box Thomas & Betts BH353A Lightweight Outlet Box Carlon E9802CN-CAR Blank Square Weatherproof Cover
Extension rings provide a means for adding 11.8 additional cubic capacity to a box or as an outlet box for surface conduit. Not designed for ceiling fan support. Four 1/2" conduit knockouts on the sides. 50 pound maximum recommended static load. Acceptable for use in 2-hour rated walls and ceilings. 1-1/2" deep x 11.8 cubic inches. UL Listed. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. UV resistant, suitable for outdoor use. For use in wet or damp locations, UL Marine Listed. Non-metallic, non-corrosive, will not rust or fade. Fits two gang metallic and non metallic boxes. Includes stainless steel mounting screws and gasket. UL Listed.
Raco 175 Ceiling Outlet Box Quantum 66215 Alkaline Battery Quantum 66248 Alkaline Battery
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 2-1/8" deep, 21.5 cubic inch capacity. UL Listed. Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check.
Thomas & Betts SC200DV Dual Voltage Outlet Box Eveready 1215 Non-Rechargeable Super Battery Allied Moulded 9361-ESK Old Work Switch Box
Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed.
Eveready 1212 Non-Rechargeable Super Battery Raco 780 Mud-Ring Raised Square Electrical Box Cover Hubbell 518 Gangable Switch Box
Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded.
Hubbell 160 Octagon Box Thomas & Betts B232B-UPC Outlet Box Raco 112 Electrical Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Octagon boxes can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls.
Raco 223 Electrical Box Coleman 95529 Low Voltage Light Bulb Carlon Super Blue BH118R Old Work Outlet Box
Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Clear replacement bulb. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed.
BOX OCT 4IN 1-1/2DP NM CLAMP  Raco 529 Gangable Switch Box Carlon A122 ENT Flexible Raceway Outlet Box
With non-metallic sheathed cable clamps. With ear brackets. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 15.5 cubic inch capacity. Acceptable for use in 2-hour fire rated walls. UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth.
Raco 545 Non-Gangable Old Work Switch Box Coleman 95527 Low Voltage Light Bulb Allied Moulded 2300-NK Switch Box
Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Clear replacement bulb. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed.
Raco 508 Non-Gangable Switch Box Raco 487 Gangable Old Work Switch Box Raco 8601 Gangable Switch Box
Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed.
Raco TigerGrip 523 Gangable Old Work Switch Box Jandorf 60490 Lampholder Fixture Socket Carlon Super Blue BH234R Old Work Outlet Box
One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded. Jandorf Lamp Socket, 660 W Lamp, 1000 V, Fluorescent Lamp, Single Pin Base Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed.
Energizer ECR1616BP Coin Cell Battery Thomas & Betts B355R Outlet Box Raco 2011FBAR Vapor Barrier Box
Replaces all 1616 batteries. 16.0mm diameter x 1.6mm height. Lithium / Manganese Dioxide (Li/MnO2). 55 mAh (to 2.0 volts). Carded. UL Listed: MH12454. Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs.
Coleman 95518 Low Voltage Halogen Lamp Coleman 95517 Low Voltage Halogen Lamp Coleman 95507 Low Voltage Halogen Lamp
Landscape lighting clear replacement bulb. Landscape lighting T3 clear replacement bulb. Landscape lighting clear replacement bulb.
Coleman 95508 Low Voltage Halogen Lamp Sliderbox SB Adjustable Switch/Receptacle Outlet Box Raco 8235 Electrical Box
Landscape lighting clear replacement bulb. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings. Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed.
MOUNT PLATE 4IN STRIP LIGHT   Coppertop MN2400B4Z AAA Alkaline Battery Coppertop MN1500B4Z Non-Rechargeable Alkaline Battery
Junction box cover plate. 4 inch. High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F. High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F.
Eveready Gold A92 Alkaline Battery Eveready Gold A91BP-4 Alkaline Battery Raco 605 Gangable Switch Box
Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed.
Energizer A23 Miniature Alkaline Battery Jandorf 60493 Lampholder Fixture Socket Carlon B455A-UPC Outlet Box
Designed for electronic applications which may require high rate pulses such as remotes and cameras. Cell is eight No. LR932 batteries in series in a battery stack. 65 mAH. Carded. Jandorf Lamp Socket, 660 W Lamp, 1000 V, Fluorescent Lamp, Single Pin Base, Plunger Terminal Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5".
Coppertop MN1300B2Z Non-Rechargeable Alkaline Battery Coppertop MN1400B2Z High Capacity Alkaline Battery Coppertop MN1604B1Z Alkaline Battery
Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. High energy density, capable of performance at high discharge rates.
Eveready Gold A522 Alkaline Battery Eveready Gold A93BP-2 Alkaline Battery Energizer E93 Alkaline Battery
Rated capacity at 25 mA continuous drain. 0 to 130 degrees F operating temperature. Up to 80 percent capacity remaining after 5 years of storage. 565 MAH. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Energizer E95 Alkaline Battery Energizer E92BP-4 Non-Rechargeable Alkaline Battery Energizer E91BP-4 Non-Rechargeable Alkaline Battery
Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Energizer L91BP-2 Non-Rechargeable Cylindrical Lithium Battery Energizer L92 Cylindrical Electronic Ultimate Lithium Battery Duracell DL1/3NBBPK Lithium Battery
Shelf life of 15 years at 21 degrees C (90 percent of rated capacity). UL Listed: MH29980. Typical capacity: 3000 mAh (to 1.0 volt). Carded. Shelf life of 15 years at 21 degrees C (90 percent of rated capacity). UL Listed: MH29980. Typical capacity: 3000 mAh (to 1.0 volt). Carded. Lasts longer than alkaline in electronic devices.
Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box Thomas & Betts B234ADJ Wall Box Jandorf 60497 Lampholder Fixture Socket
Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Jandorf Lamp Socket, 660 W Lamp, 600 V, Fluorescent Lamp, Medium Bi-Pin Base
Thomas & Betts BH464A Rigid Outlet Box Energizer E90 Specialty Alkaline Battery Allied Moulded 9312-EWK Old Work Outlet Box
Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. Plastic label jacket. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. 1,000 mAH. Carded. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed.
Energizer 1209 Super Lantern Battery Eveready Gold A95BP-2 Alkaline Battery Allied Moulded 3300-NK Outlet Box
Carbon-Zinc battery. Plastic jacket. Coil spring terminal. 6 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 degrees F to 130 degrees F. Lower unit weight than alkaline. 11 AH to 0.8 volt. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed.
Energizer E96 Non-Rechargeable E2 Alkaline Battery Energizer 522 Alkaline Battery Zero-Mercury A544BPZ Miniature Alkaline Battery
Plastic label jacket. Delivers longer-lasting, more powerful performance for demanding, high-tech devices such as MP3 players, portable CD players, digital cameras, hand-held electronic games, and other digital devices. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. 625 MAH. Carded. Metal jacket. Up to 80 percent capacity remaining after 5 years of storage. 9 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. 625 MAH. Carded. Size replaces 544, PX28A, 4LR44 and V4034PX. 6 volt,  150 mAh. Cell is four No. A76 batteries in series with a metal jacket. 150 mAH. Carded.
Energizer ECR1632BP Coin Cell Battery SOCKET NON SHUNTED 4 PACK     Jandorf 60491 Lampholder Fixture Socket
For electronics around the house, like keyless entry, electronic books and glucose monitors. Performs in extreme temperatures from -22 to 140 degrees F. Holds power for 8 years when not in use. Replacement for: BR1632, DL1632, ECR1632, KCR1632, KECR1632, KL1632, L1632. UL Listed. Universal non shunted bi-pin T8/T12 tombstone and U-shape tombstone replacement sockets. Jandorf Lamp Socket, Low Profile, 660 W Lamp, 1000 V, Fluorescent Lamp
Jandorf 60494 Lampholder Fixture Socket Quantum 66217 Alkaline Battery Quantum 66249 Alkaline Battery
Jandorf Lamp Socket, Low Profile, 660 W Lamp, 1000 V, Fluorescent Lamp, Plunger Terminal Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check.
Tiger Grip 517 Gangable Switch Box Energizer 2032BP-2 Coin Cell Battery Energizer 2016BP-2 Button Cell Battery
Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed. Replaces Duracell DL2032, Energizer ECR2032, Panasonic CR2032, and Rayovac CR2032. 20.0mm diameter x 3.2mm height. Lithium / Manganese Dioxide (Li/MnO2). 240 mAh (to 2.0 volts). Carded. UL Listed: MH12454. Replaces Energizer ECR2016. .08" diameter x .008" height. Lithium / Manganese Dioxide (Li/MnO2), 90 mAh (to 2.0 volts) typical capacity, 1.9 grams (0.07 oz.) typical weight. Carded. UL Listed: MH12454.
Coleman 95499 Low Voltage Halogen Lamp Coleman 11604 Low Voltage Connector Raco 878 Utility Exposed Work Cover
Landscape lighting T3 clear replacement bulb. For connection of  low voltage cable for landscape lights. Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle 2.141" diameter. 10.3 cubic inch capacity. UL Listed.
Raco 681 Switch Box Zero-Mercury 357BPZ-3 Non-Rechargeable Electronic Coin Cell Battery Carlon B468R Old Work Outlet Box
Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Replaces AG13, LR1154, EPX76, A76, LR44, SR44SW/W; Duracell D357/303, Goldpeak 357, Kodak L1154, Maxell SR44W, Panasonic SP357, Rayovac 357, Renata 357, Sony SR44W, Toshiba SR44W, and Varta V357. 11.6mm diameter x 5.4mm height. 150 MAH to 1.3 volt. Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89".
Energizer 2025BP-2 Coin Cell Battery Raco 8240 Electrical Box Raco 685 Switch Box
Replaces Duracell DL2025 and Rayovac CR2025. 20.0mm diameter x 2.5mm height. Lithium / Manganese Dioxide (Li/MnO2). 170 mAh to 2.0 volt. Carded. UL Listed: MH12454. Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed.
Raco 2002FBAR Vapor Barrier Box Raco 888 Raised Square Exposed Work Cover Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box
Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Used to mount switch or receptacle on box in surface mount applications. Raised 1/2". For one 30-60 amp, single receptacle 2.625" diameter. 10.3 cubic inches. UL Listed. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed.
Sliderbox SB Adjustable Switch/Receptacle Outlet Box Jandorf 60488 Lampholder Fixture Socket Jandorf 60487 Lampholder Fixture Socket
Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 42 cubic inch volume, two 1/2" knockouts. Internal steel, stud/wood screws. 3-9/16" depth x 4" width x 3-3/4" height. UL listed for 2 hour fire resistive walls. Jandorf Lamp Socket, 660 W Lamp, 600 V, Fluorescent Lamp, Medium Bi-Pin Base Jandorf Lamp Socket, 660 W Lamp, 600 V, Fluorescent Lamp, Medium Bi-Pin Base