Home > ELECTRICAL > SPECIALTY ELECTRICAL > FLASHLIGHTS > FLASHLIGHT / LANTERN BULBS
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Thomas & Betts BH122A-UPC Outlet Box Carlon B112HB Handy Box Hubbell 8660 Utility Box
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Thomas & Betts B114R-UPC Switch Box Thomas & Betts B232A-UPC Outlet Box Hubbell 8192 Outlet Box
Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code.
Thomas & Betts B108B-UPC Outlet Box Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box
New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4".
Allied Moulded 1098-N Switch Box Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05".
Raco 8190 Outlet Box Raco 8189 Ceiling Outlet Box Raco 7887RAC Old Work Cable Box
Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Allied Moulded 1099-N Switch Box Hubbell 8650 Welded Utility Box Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box
Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Raco 8196 Electrical Box Hubbell 8670 Welded Utility Box
Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed.
Thomas & Betts B120R Outlet Box Raco 662 Drawn Utility Box Raco 653 Utility Box
With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches. Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed.
Raco 8197 Welded Electrical Box Thomas & Betts BH235A Outlet Box Carlon A521DE ENT Flexible Raceway Outlet Box
Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed.
Hubbell 665 Utility Box Extension Ring Carlon SC100A 1-Gang Low Voltage Mounting Bracket Hubbell 8663 Utility Box
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed.
Raco 473 Gangable Switch Box Hubbell 8232 Outlet Box Carlon SC200RR Low Voltage Old Work Bracket
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed.
Dorcy 411663 Replacement Krypton Lamp Dorcy 411664 Krypton Lamp Dorcy 411661 Replacement Krypton Lamp
Replacement bulb with tungsten filament wires, glass tubes and copper stems. Replacement bulb with tungsten filament wires, glass tubes and copper stems. Replacement bulb with tungsten filament wires, glass tubes and copper stems.
Dorcy 411660 Replacement Krypton Lamp Dorcy 411662 Replacement Krypton Lamp Raco 528 Gangable Switch Box
Replacement bulb with tungsten filament wires, glass tubes and copper stems. Replacement bulb with tungsten filament wires, glass tubes and copper stems. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Hubbell 8500 Gangable Switch Box Carlon B418A-UPC Shallow Outlet Box Thomas & Betts B225R-UPC Outlet Box
Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16"
Eveready 1250 Non-Rechargeable Electronic Battery Raco 661 Handy Box Eveready 1235 Non-Rechargeable Super Battery
Carbon-Zinc. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed. Carbon-Zinc. Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F.
Raco 400 Gangable Switch Box Thomas & Betts B121ADJ Wall Box Thomas & Betts B344AB-UPC Outlet Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Hubbell 519 Gangable Switch Box Hubbell 8531 Gangable Switch Box Raco 404 Non-Gangable Shallow Switch Box
Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed.
Hubbell 471 Gangable Switch Box Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box
Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed. Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length.
Allied Moulded 9318 Handy Box Raco 420 Gangable Switch Box Raco 560 Gangable Switch Box
Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 8355 Non-Gangable Switch Box Mag-Lite LM2A001 Replacement Xenon Lamp Mag-Lite LK3A001 Replacement High Intensity Lamp
Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Bi-pin, vacuum-sealed and extremely bright for its size. Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Bi-Pin, vacuum-sealed and extremely bright for its size. For single cell AAA Solitaire flashlight.
Raco 674 Handy Box Raco 8201 Extension Ring Outlet Box Energizer E91BP-2 Non-Rechargeable Alkaline Battery
For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed. For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Raco 7488RAC Old Work Cable Box Allied Moulded 9363-EWK Old Work Switch Box Raco 567 Gangable Switch Box
Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Hubbell 8203 Electrical Box Extension Ring Thomas & Betts B432A-UPC Outlet Box Raco 976 Extension Ring Switch Box
For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code.
Thomas & Betts BH353A Lightweight Outlet Box Quantum 66215 Alkaline Battery Thomas & Betts SC200DV Dual Voltage Outlet Box
Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved.
Eveready 1215 Non-Rechargeable Super Battery Allied Moulded 9361-ESK Old Work Switch Box Hubbell 518 Gangable Switch Box
Metal jacket, 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded.
Thomas & Betts B232B-UPC Outlet Box Raco 223 Electrical Box Carlon Super Blue BH118R Old Work Outlet Box
With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed.
Cutler Hammer BRFPP Filler Plate Raco 529 Gangable Switch Box Carlon A122 ENT Flexible Raceway Outlet Box
Plastic (snap-in) for type BR 1" space. May also be used with 400 amp and 600 amp load centers. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth.
Raco 545 Non-Gangable Old Work Switch Box Raco 8211 Outlet Box Allied Moulded 2300-NK Switch Box
Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed.
GROUND BAR 7 HOLE CONSUMER PK Raco 508 Non-Gangable Switch Box Hubbell 8257 Welded Outlet Box
For grounding copper or aluminum terminals in a GE load center. Offers 4 small holes for 14 - 8 AWG copper or 12 - 8 AWG aluminum terminals and 3 large holes for 14 - 4 AWG copper or 12 - 4 AWG aluminum terminals. UL Listed and ANSI Certified. 6.875" height x 2.875" width x 0.5" depth, .105 lb. Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed. Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed.
Raco 487 Gangable Old Work Switch Box Raco 8601 Gangable Switch Box Raco TigerGrip 523 Gangable Old Work Switch Box
Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded.
Carlon Super Blue BH234R Old Work Outlet Box Thomas & Betts B355R Outlet Box Raco 2011FBAR Vapor Barrier Box
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed. Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs.
Sliderbox SB Adjustable Switch/Receptacle Outlet Box Raco 8235 Electrical Box Coppertop MN1500B4Z Non-Rechargeable Alkaline Battery
Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings. Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed. High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F.
Eveready Gold A91BP-4 Alkaline Battery Gardner Bender GSW-61 Rotary Switch Raco 605 Gangable Switch Box
Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Brass terminals, #18 AWG, 6" stripped wire leads. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed.
Carlon B455A-UPC Outlet Box GE THFILLER Rectangle Filler Plate Coppertop MN1300B2Z Non-Rechargeable Alkaline Battery
Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5". Covers circuit breaker knock outs that have been removed in error.  Two 1" and two 1/2" plates. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates.
Coppertop MN1400B2Z High Capacity Alkaline Battery Eveready Gold A93BP-2 Alkaline Battery Energizer E93 Alkaline Battery
Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Energizer E95 Alkaline Battery Mag-num Star LMSA401 Replacement Xenon Lamp Mag-num Star LMSA601 Replacement Xenon Lamp
Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Works with C or D battery flashlights. Bulbs sold one per card. Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Works with C or D battery flashlights. Bulbs sold one per card.
Mag-num Star LMSA201 Replacement Xenon Lamp Mag-num Star LMSA301 Replacement Xenon Lamp Mag-num Star LMSA501 Replacement Xenon Lamp
Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Works with C or D battery flashlights. Bulbs sold one per card. Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Works with C or D battery flashlights. Bulbs sold one per card. Specifically designed to deliver the brightest, whitest, far-reaching light beam without compromising battery life. Works with C or D battery flashlights. Bulbs sold one per card.
Energizer E91BP-4 Non-Rechargeable Alkaline Battery LUG KIT NO6-2/0 NEUTRAL/GROUND Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box
Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. For use with wire range 6-2/0. Can be mounted on any neutral or ground position by simply removing the termination screw. UL Listed. 2.875" height x .75" width x  6.875" depth, .07 lb. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed.
Raco 8265 Ceiling Outlet Box Thomas & Betts B234ADJ Wall Box Square D QO70AN Auxiliary Neutral Lug Kit
Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed. Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Made for QO load centers. Field installed for number 12 - 2 Al or number 14 - 4 Cu wire. QO accessories can only be used with QO load centers.
Schneider PK3GTA-1CP Ground Bar Kit Thomas & Betts BH464A Rigid Outlet Box Allied Moulded 9312-EWK Old Work Outlet Box
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed.
Gardner Bender GSW-69 Rotary Switch Eveready Gold A95BP-2 Alkaline Battery Square D QOFPCP Filler Plate
Black plastic, .516",  brass terminals, #18 AWG, 6" stripped wire leads. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Fills opening in covers if twistout is removed in error. QOFPCP are used only in QO load centers, filling the spaces where no circuit is attached. CHOMFPCP are for use only in Homeline load centers. UL Listed and ANSI Certified.
Allied Moulded 3300-NK Outlet Box BULB CONVERSION LED 2CELL     BULB CONVERSION LED 3/4CELL
Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed. Conversion bulb operates with any 2 cell AA, C, or D flashlight. 10 year bulb, 100,000 hours of use. 30 lumen 3 volt replacement. Conversion bulb operates with any 3 cell, 4 cell, or 6V lantern or flashlight. 100,000 hours of use. 40 lumen, 4.5 volt.
Jandorf 61216 Single Circuit Rotary Switch Jandorf 61217 Single Circuit Rotary Switch Gardner Bender GSW-62 Rotary Switch
Jandorf Rotary Switch, Single Circuit, Series: 61216, 125 V, 1 A, Contact Configuration: SPST, On/Off, 1 Poles, 2-Wire Terminal, Black Hat Canopy, UL Listed Jandorf Rotary Switch, Single Circuit, Series: 61217, 125 V, 1 A, Contact Configuration: SPST, On/Off, 1 Poles, 2-Wire Terminal, White Hat Canopy, UL Listed Brass terminals, #18 AWG, 6" stripped wire leads. .406" mounting hole. CSA Listed.
Square D PK4GTACP Ground Bar Kits Quantum 66217 Alkaline Battery Square D PK7GTACP Ground Bar Kits
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Tiger Grip 517 Gangable Switch Box Square D HOMFPCP Filler Plate Jandorf 61220 Single Circuit Rotary Switch
Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed. Fills opening in covers if twistout is removed in error. QOFPCP are used only in QO load centers, filling the spaces where no circuit is attached. CHOMFPCP are for use only in Homeline load centers. UL Listed and ANSI Certified. Jandorf Rotary Switch, Single Circuit, Series: 61220, 125 V, 1 A, Contact Configuration: SPST, On/Off, 1 Poles, 2-Wire Terminal, Brass Knob, UL Listed
GROUND BAR 24 HOLE PM-GOLD PK Raco 680 Switch Box Raco 681 Switch Box
Used for additional grounding as required by local code. Compatible with most load center enclosures. Fits solid or stranded 4 - 14 copper wire and 10 - 12 aluminum wire. Includes mounting screws. UL Listed and ANSI Certified. 11" height x 3.5" width x 0.5" depth, .304 lb. Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B468R Old Work Outlet Box Square D HOM100AN Neutral Lug Kit Raco 8240 Electrical Box
Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". Breaker box neutral lug is designed for Homeline load centers. It works with number 1 - 1/0 copper and aluminum wire. UL Listed, ANSI Certified. Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 685 Switch Box Jandorf 61215 3-Way Double Circuit Rotary Switch Hubbell 683 Switch Box
Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed. Jandorf Rotary Switch, 3-Way Double Circuit, Series: 61215, 125 V, 3 A, Off/On/On/On, 2 Poles, 4 Positions, 3-Wire Terminal, Brass Knob, UL Listed Drawn construction for surface mount applications. Conduit wiring system. Eight 1/2" and four 3/4" conduit knockouts (sides). Three 1/2" and two 3/4" conduit knockouts (bottom). 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 2002FBAR Vapor Barrier Box Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box
Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 42 cubic inch volume, two 1/2" knockouts. Internal steel, stud/wood screws. 3-9/16" depth x 4" width x 3-3/4" height. UL listed for 2 hour fire resistive walls.
Allied Moulded 9313-EWK Old Work Switch Box Schneider PK9GTACP Ground Bar Kit Square D ACPCP Closing Plate
Thermoset-fiberglass with ears, wing brackets, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" depth x 5-15/16" x 3-1/4". UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Used for sealing off a hub opening when a service feed originates underground. The plate is compatible with A-type openings and can be used on outdoor devices that utilize a 4-hole mounting pattern. Use for A-size hub opening for Square D metering equipment. UL and CSA Listed.
Mag-Lite LR00001 Replacement Halogen Lamp Siemens EC2GB152 Ground Bar Kit With Terminal 2/0 Lug Powerzone LR6-16P Alkaline Battery
Fits RE1019 rechargeable Mag Charger flashlight. For equipment grounding provision. #14 to 4 AWG, 60/75 degree Celsius, Cu/A1. Mercury and cadmium free.
Cutler-Hammer GBK10P Ground Bar Kits Raco 509 Old Work Switch Box Square D PK12GTACP Ground Bar Kits
Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed. Conduit wiring system. Gangable switch box offers the option of constructing a box to hold two or more devices. Adjustable plaster ears allow box to be used in old work applications. Provided old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Two 1/2" bottom knockouts and two 1/2" end knockouts. 2-1/2" deep - 12.5 cubic inches. UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Coppertop MN15B8ZTSS Alkaline Battery Siemens EC38595 Closure Plate Square D PK15GTACP Ground Bar Kits
High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F. Fits any meter socket application where a closure plate is needed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Cutler-Hammer GBK14P Ground Bar Kits Energizer E91MP-8 Non-Rechargeable Alkaline Battery Coppertop MN1300R4Z Alkaline Battery
Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates.
Coppertop MN1400R4ZX Alkaline Battery Eveready Gold A91BP-8 Alkaline Battery Jandorf 61214 3-Way Double Circuit Rotary Switch
Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Jandorf Rotary Switch, 3-Way Double Circuit, Series: 61214, 125 V, 3 A, Off/On/On/On, 2 Poles, 4 Positions, 3-Wire Terminal, Brass Knob, UL Listed
Philips Comp-Covered LC1420CI Magnetic Ballast Jandorf 61005 Single Circuit Rotary Switch Energizer L91BP-4 Non-Rechargeable Cylindrical Lithium Battery
For use with one F14T8, F15T8, F18T8, F19T8, F14T12, F15T12, or F20T12 bulb. Minimum start temperature 50 degrees. 120 volt. UL and CSA listed. Jandorf Rotary Switch, Single Circuit, Series: 61005, 125 V, 6.5 A, Contact Configuration: TPST, Off/On/On/On, 1 Poles, 5-Tab Terminal, Black, UL Listed Shelf life of 15 years at 21 degrees C (90 percent of rated capacity). UL Listed: MH29980. Typical capacity: 3000 mAh (to 1.0 volt). Carded.
Energizer E95BP-4 Non-Rechargeable Alkaline Battery Energizer E93BP-4 Alkaline Battery Schneider PK18GTACP Ground Bar Kit
Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Eveready Gold A93BP-4 Alkaline Battery Siemens Energy ECGB10 Ground Bar Kits Square D PK23GTACP Ground Bar Kits
Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. For equipment grounding provision. #14 to 4 AWG, 60/75 degree Celsius, Cu/A1. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Jandorf 61004 Rotary Switch Jandorf 61204 Rotary Switch Siemens EC3GB302 Ground Bar Kit With Terminal 2/0 Lug
Jandorf Rotary Switch, Series: 61004, 125 V, 3 A, Contact Configuration: TPST, Off/L1/L2/L3, 3 Poles, 4-Push-In Terminal, Black, UL Listed, 3-Speed Jandorf Rotary Switch, Series: 61204, 125 V, 6.5 A, Contact Configuration: TPST, Off/L1/L2/L3, 3 Poles, 4-Wire Terminal, Black, UL Listed, 3-Speed For equipment grounding provision. #14 to 4 AWG, 60/75 degree Celsius, Cu/A1.
Jandorf 61206 3-Way Double Circuit Rotary Switch Powerzone LR6-24P Alkaline Battery Eveready Gold A95BP-4 Alkaline Battery
Jandorf Rotary Switch, 3-Way Double Circuit, Series: 61206, 125 V, 3 A, Off/L1/L2/L1-2, 2 Poles, 4 Positions, 3-Wire Terminal, Brass Knob, UL Listed, 2-Speed Mercury and cadmium free. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
Jandorf 61033 Single Circuit Rotary Switch Jandorf 61034 Single Circuit Rotary Switch Quantum 66225 Alkaline Battery
Jandorf Rotary Switch, Single Circuit, Series: 61033, 125 V, 1 A, Contact Configuration: SPDT, Off/On/On, 1 Poles, 3-Tab Terminal, Plastic Knob, Black, UL Listed Jandorf Rotary Switch, Single Circuit, Series: 61034, 125 V, 1 A, Contact Configuration: SPTT, Off/On/On/On, 1 Poles, 4-Tab Terminal, Plastic Knob, Black, UL Listed Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check.
Coppertop MN15RT12Z Reclosable Alkaline Battery Raco 686 Switch Box BULB LED CONVERSION C/D BATT
High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F. Welded construction. Conduit wiring system. Two 1/2" and two 3/4" knockouts (sides). Three 1/2" and three 3/4" knockouts (bottom). Six 1/2" and six 3/4" knockouts (end). FM type bracket for wood or metal studs. 2-1/2" deep - 47.8 cubic inches. UL Listed. Converts most C & D (2-6 cell PR style flange) incandescent flashlights into bright, long lasting (100,000 hour) LED flashlights. It's as easy as replacing the bulb. Self-adjusting for all capacity levels, this efficient LED technology also ensures a much longer battery life. Improves light quality, emits a pure white (as opposed to the incandescent dull yellow) light. 55 lumen output.
Cutler Hammer GBK21P Ground Bar Kit BOX 3GANG 1-5/8DEEP 1/2-3/4 KO Eveready EN91 Non-Rechargeable Industrial Alkaline Battery
Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed. Used where a number of wiring devices are to be centrally located. Features 1/2" and 3/4" concentric knockouts for use with a wide variety wiring methods. 1-5/8" x 4.5" x 8.63". UL Listed. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Not intended for retail sale. Carded.
Coppertop MN1500B16 Alkaline Battery Energizer E91LP-16 Non-Rechargeable Alkaline Battery Energizer EN93 Non-Rechargeable Industrial Alkaline Battery
High energy density, capable of performance at high discharge rates. Typical temperature range: -4 to 130 degrees F. Up to 85 percent capacity remaining after 4 years of storage at 70 degrees F. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 8,350 MAH to 0.8 volt. Operating temperature 0 to 130 degrees F. Not intended for retail sale.
Quantum 66233 Alkaline Battery Square D S106 Replacement Screw Coppertop MN14R8DWZ17 Double Wide Alkaline Battery
Lasts longer in high-drain and frequently used devices that require high battery output like video game controllers and high-powered flashlights. Duralock technology. With power check. Fit many types of service entrance devices and load center covers. Use them to replace lost or damaged screws. Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates.
Coppertop MN13R8DWZ17 Double Wide Alkaline Battery Siemens ECLK2125 Sub-Feed Lug Kit Energizer EN95 Non-Rechargeable Industrial Alkaline Battery
Lasts longer in high-tech devices. High energy density, capable of performance at high discharge rates. Sub feed lug kit. 125 amp. 2 pole. Lugs to sub feed to another panel. Long lasting. 1.5 volt, 25 mA continuous drain at rated capacity. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 8,350 MAH to 0.8 volt. Operating temperature 0 to 130 degrees F. Not intended for retail sale.
Energizer E95BP-8H Non-Rechargeable Alkaline Battery Energizer E93BP-8H Alkaline Battery Raco 687 Switch Box
Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Tester on every battery. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded. Conduit wiring system. Welded construction. FM bracket for wood or metal studs. Eight conduit knockouts (sides). Two conduit knockouts (end).  Four conduit knockouts (bottom). 63.5 cubic inch capacity. 7-19/32" wide x 2-1/2" deep. UL Listed.
Carlon SC300PRR Electrical Box Pro-Cell PC1400 Alkaline Battery BATTERIES 2AA 24PACK
BATTERIES 2AA 24PACK
Our Price: $17.46
Nonmetallic ABS material is lightweight, paintable and easy to handle. Recessed low profile design provides ample room behind dry wall and between studs to accommodates cable bend requirements. Hides the wires, cables, cords and plug heads used with flat panel display installations. Has a two gang low voltage opening and a universal one gang opening for an outlet or switch box (boxes, devices, and plates not included). 4 swing out clamps lock the plate securely to the wall, horizontal or vertical mount. 2.72" depth x 5.25" width x 10.5" length. Long lasting power. Formulated to provide dependable, long-lasting power. Use in toys, audio devices, flashlights, electronic devices, remote control communication devices, smoke detectors and security systems. Plastic label jacket. Up to 80 percent capacity remaining after 7 years of storage. 1.5 volt, 25 mA continuous drain at rated capacity. Operating temperature 0 to 130 degrees F. Carded.
BATTERIES 2AA 12PACK          Pro-Cell PC1300 Non-Rechargeable Alkaline Battery Pro-Cell PC1500KD Alkaline Battery
BATTERIES 2AA 12PACK
Our Price: $17.46
Lasts longer, especially in moderate to heavy drain applications. Good performance in extreme temperatures from -40 to 140 degrees Fahrenheit. Holds power in storage for up to 20 years. 33 percent lighter than alkaline batteries. Long lasting power. Long lasting power.
Philips Centium ICN2P32N35I Electronic Ballast Philips Centium ICN2S40N Electronic Ballast MTL BRKT FOR 8FT STRP LT RTOFT