Home > ELECTRICAL > ROUGH ELECTRICAL > OUTDOOR BOXES & LAMPHOLDERS > WEATHERPROOF BOXES
Sort By:
1
TAPE ELECT VNYL BLK 3/4INX60FT Intertape 602 Electrical Tape Calterm 49305 Electrical Tape 30 ft L x 7.5 mil T
Black vinyl electrical tape for common electrical uses. 7 mil., UL Approved. General purpose electrical insulating tape, good dielectric strength. 7 mils thick. UL Listed and CSA Certified. Black PVC electrical tape is UL Listed to 600 volt. 7.5 mil. thickness and a temperature rating up to 80 degrees Celsius/176 degrees Fahrenheit. Elongation of 200 percent allows tight wrapping and sealing.
WireGard 19-AWC Assortment Wire Connector Kit WireGard 19-001 Twist-On Wire Connector WireGard 19-002 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WireGard 19-003 Twist-On Wire Connector WireGard 19-004 Twist-On Wire Connector WireGard 19-006 Twist-On Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
WingGard 19-084 Twist-On Wire Connector WingGard 19-086 Twist-On Wire Connector Hex-Lok 19-2H2 Hex Lock Wire Connector
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
WingGard 19-089 Twist-On Wire Connector GreenGard 19-095 Grounding Wire Connector Intertape 85828 Electrical Tape
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85827 Electrical Tape Intertape 85835 Electrical Tape Intertape 85830 Electrical Tape
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified.
Intertape 85832 Electrical Tape Intertape 85831 Electrical Tape Scotch 4218-BA-40 Electrical Tape
For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. For use up to 600 volts. PVC film coated with a non-corrosive rubber based adhesive. Resistant to water, oils, acids, alkalis and other corrosive chemicals. Lead free. Temperature range from 32 to 176 degrees F. Used to repair frayed wiring, splice wiring, protect wire nut connections, resurface and insulate hand tools and general purpose maintenance and repair. 7 mil. thick. UL Listed and CSA Certified. Commercial grade 7-mil polyvinyl chloride insulating tape, flame retardant and provides mechanical protection with minimum bulk. Excellent resistance to abrasion, moisture, acids, copper corrosion and varying weather conditions. UL Listed and CSA Certified.
Calterm 61470 Assortment Wire Cap Set WireGard 25-002 Twist-On Wire Connector Gardner Bender GTF-300 Friction Tape
Suitable for solid or stranded copper wire. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. For use over electrical tape splices. Matted finish provides the best gripping surface available. Use to wrap grips on hand tools.
WireGard 25-001 Twist-On Wire Connector GB-Gardner Bender GTB-667P Electrical Tape GB-Gardner Bender GTW-667P Electrical Tape
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2.
Calterm 61606 Terminal Lug Hex-Lok 19-1H1 Hex Lock Wire Connector GB-Gardner Bender GTO-667P Electrical Tape
Dimensions: 3/8" stud x 2-3/8" length. Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs. Quality colored electrical tape, designed for general purpose electrical applications. Made from low-lead PVC material, is resistant to abrasion, UV rays, moisture and many acids. 7 mil (0.18) commercial grade, weather resistant, pressure sensitive. Flame retardant and can be used as primary insulation for splices up to 600 volts and 80 degrees C (176 degrees F). UL 510, CSA 22.2.
WireGard 25-003 Twist-On Wire Connector Gardner Bender 20-089 Closed End Crimp Pigtail Connector Gardner Bender 20-090 Closed End Crimp Pigtail Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed. Tin-plated seamless copper closed-end crimp connector for use with solid or stranded wire. Vibration resistant, corrosion and chemical resistant. UL listed.
Gardner Bender GTA-2 Mechanical Lug PushGard 19-PC2 2-Port Push-In Connector Calterm 61607 Terminal Lug
Single conductor, features high-strength, low-resistance aluminum construction. Accepts wire from number 14 to number 10 gauge AWG stranded, and number 14 to number 2 gauge AWG solid. UL Listed. Card of 2. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Dimensions: 3/8" stud x 2-3/8" length.
Super 33+ 195NA Electrical Tape PushGard 19-PC3 3-Port Push-In Connector WingGard 25-084 Twist-On Wire Connector
For insulating, repairing and protecting electrical wire. UL Listed. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
PushGard 19-PC4 4-Port Push-In Connector WireGard 25-004 Twist-On Wire Connector Gardner Bender DS-110N Duct Seal Insulator
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Malleable non-conductive compound for sealing of electrical raceway connections from air, noise and moisture.
Gardner Bender GSLU-35 Single Hole Mechanical Lug Gardner Bender TK-32 Assortment Wire Connector Kit Hubbell 5320-0 Outlet Box
Rated for 600 volt copper only. Single hole lugs, easy to install with screwdriver, wrench or pliers. 3/8" bolt size. Slide card kit with 32 assorted wire connectors: 10 GB #1 - minimum 3 #22 maximum 2 #16, 8 GB #2 - minimum 3 #22 maximum 3 #18 w/2 #20 6 GB #3 - minimum 3 #20 maximum 2 #14, 2 GB #4 - minimum 1 #14 maximum 4 #12, 4 crimp connector #1035 - 1 #20 w/1 #12 - 2 #14, 2 crimp connector #1034 - 4 #22 - 2 #16. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Bell Raco 5320-1 Weatherproof Box Gardner Bender GTF-600 Friction Tape 3M 10414 Electrical Tape
For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. For use over electrical tape splices. Matted finish provides the best gripping surface available. Use to wrap grips on hand tools. Resists water, oils, alkalies, acids, weather, ultraviolet rays, abrasion, corrosion and moisture. Use as a primary insulation for wide cable splices up to 600 volt, for fixture and wire splices up to 1000 volt and to maintain electrical and high temperature integrity of electrical systems. 7 mil, UL Approved and CSA Certified.
WingGard 25-086 Twist-On Wire Connector Gardner Bender 10-100 Tap Splice Gardner Bender GTP-307WD All Weather Electrical Tape
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. For snap-in splicing of low-voltage AWG wire without prior stripping. 75 degree Celsius temperature rating. Clamshell. General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit.
Gardner Bender RTP-3422 Self-Sealing Electrical Tape LUG CU HD 6AWG 5/16IN STUD SZ LUG CU HD 6AWG 3/8IN STUD SZ
Insulates and seals surfaces. Fuses to itself during application to stay watertight. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. Heavy-duty lugs made from pure copper for maximum current flow. Tinned for corrosion resistance. Seamless barrel for maximum strength. Closed ends seal out moisture. Heavy-duty lugs made from pure copper for maximum current flow. Tinned for corrosion resistance. Seamless barrel for maximum strength. Closed ends seal out moisture.
Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape Scotch 35 Color Coding Electrical Tape
Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified.
Scotch 35 Color Coding Electrical Tape DryConn 20101 Low Voltage Wire Connector DryConn 62210 Safety Sealed Waterproof Wire Connector
Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Suitable for all low voltage applications. For use in lighting, irrigation, and underground wiring. No junction box required. Filled with petroleum based sealant. 30 volt/10 amps maximum. 13/16" x 19/16". Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL 486D Listed.
DryConn 62110 Safety Sealed Waterproof Wire Connector DryConn 62310 Safety Sealed Waterproof Wire Connector Hubbell 5320-6 Outlet Box
Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL 486D Listed. Suitable for all wire splices, especially those exposed to condensation, water vapors or dust. UL 486D Listed. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Dulux 21278 Double CFL Dulux 21273 Single Tube CFL Scotch Super 33+ 6132 Electrical Tape
Single compact fluorescent lamp with 2-pin base,  ECOLOGIC for use on magnetic ballast. 10,000 average life hours. Single compact fluorescent lamp with 2-pin base,  ECOLOGIC for use on magnetic ballast. 10,000 average life hours. Resists water, oils, alkalies, acids, weather, ultraviolet rays, abrasion, corrosion and moisture. Use as a primary insulation for wide cable splices up to 600 volt, for fixture and wire splices up to 1000 volt and to maintain electrical and high temperature integrity of electrical systems. 7 mil, UL Approved and CSA Certified.
Bell Raco 5406-0 Weatherproof Extension Box Bell Raco 5320-2 Weatherproof Box Mintcraft CP-323L Wire Cap Set
Used to provide additional capacity. Die cast aluminum construction. Installation hardware, gasket, and ground screw provided. 9.5 cubic inch capacity. 4-1/2" x 2-3/4" x 1" deep. UL Listed, CSA, NEMA 3R Rated. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Thirty two piece, for AWG #24 to AWG #10 solid or standard copper wire. Contains: 10 pc wire joint 22-16  300 volt, 2/#22 - 2/#16. 8 piece wire joint 22-14 300 volt 3/#22 - 3/#16. 6 pc wire joint 22-14 600 volt 2/#18 - 4/#16. 2 piece wire joint 18-12 600 volt 1/#18 + #14 - 1 and 2/#14 + 3/#16. 4 piece closed end pigtail 16-14 2/#22 - 2/#14. 2 piece closed end pigtail 12-10 2/#18 - 2/#10.
Designer'S Choice 20404 Single Tube CFL Dulux S 20403 Single Tube CFL Super 33+ 200 Electrical Tape
Saves energy costs by replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall sconed, exit signs, and task lighting. Ecologic, 10,000 average life hours. 82 CRI (Color Rendering Index). 120 volt, carded. Saves energy costs by replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall sconed, exit signs, and task lighting. Ecologic, 10,000 average life hours. 82 CRI (Color Rendering Index). 120 volt, carded. Vinyl electrical tape, black, 7 mil thick with PVC backing, provides protective jacketing for high-voltage cables and wire harnesses, and primary electrical insulation for splices up to 600 volt. Abrasion, corrosion, and UV resistant, resists alkalis and acids, and is flame-retardant. All-weather performance in cold to 0 degrees F or heat to 220 degrees F. UL Listed and CSA Certified.
Dulux S 20479 Single Tube CFL Gardner Bender GSLU-25 Single Hole Mechanical Lug DryConn 10600 Twist-On Underground Wire Connector
Saves energy costs by replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall sconed, exit signs, and task lighting. Ecologic, 10,000 average life hours. 82 CRI (Color Rendering Index). 120 volt, carded. Rated for 600 volt copper only. Single hole lugs, easy to install with screwdriver, wrench or pliers. 3/8" bolt size. Rated for all underground direct bury applications. Use on all lighting, irrigation, and underground wiring. Additional sealant for long term service. No junction box needed. 600 volt maximum with building wire, 1000 volt in fixtures and signs. #8 to #22 wire range. UL 486D Listed.
WireGard 25-AWC Assortment Wire Connector Kit WireGard 25-006 Twist-On Wire Connector Scotch 03407 Friction Tape
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Good abrasion resistance, used for protection for electrical tape splices and connectors. Made in the USA. UL Approved.
PushGard 19-PC8 8-Port Push-In Connector Hubbell 5324-0 Outlet Box Powerzone PZ-103PDQ Replacement CFL
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Three threaded 3/4" outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. Fits most fluorescent work lights and commercial fixtures. Carded.
Jandorf 60766 Lug Terminal Jandorf 60767 Lug Terminal Jandorf 60772 Lug Terminal
Jandorf Lug Terminal, Series: 60766, 2 AWG Conductor, 1/2 in Stud, Non-Insulated Insulation, Tin Plated Copper, UL Listed Jandorf Lug Terminal, Series: 60767, 2 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Tin Plated Copper, UL Listed Jandorf Lug Terminal, Series: 60772, 1/0 AWG Conductor, 1/2 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed
Jandorf 60773 Lug Terminal Scotch 88 Cold Weather Electrical Tape Hubbell 5321-0 Outlet Box
Jandorf Lug Terminal, Series: 60773, 1/0 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed Thick 8.5 mil. Recommended for low temperature applications because of its superior cold weather handling features. Flexible for use on small wires. Inside or outside. Resists cold, ultraviolet rays, moisture, alkalies, acids and corrosion. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
LUG CU HD 4AWG 5/16IN STUD SZ Bell Raco 5320-7 Weatherproof Outlet Box Dulux S 20484 Single Tube CFL
Heavy-duty lugs made from pure copper for maximum current flow. Tinned for corrosion resistance. Seamless barrel for maximum strength. Closed ends seal out moisture. For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Saves energy costs by replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall sconed, exit signs, and task lighting. Ecologic, 10,000 average life hours. 82 CRI (Color Rendering Index). 120 volt, carded.
Bell Raco 5320-5 Outlet Box Dulux S 20478 Single Tube CFL Sylvania Deluxe S 800 Compact Fluorescent Bulb
For use in wet, damp or dry locations. Three 1/2" threaded outlets. 2" deep with lugs. May be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs. Powder coat finish. Eight box mounting options with detachable lugs provided. Includes two closure plugs. Ground screw installed. Multi-lingual instructions. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Die cast aluminum construction. 18.3 cubic inch capacity. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Saves energy costs by replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall sconed, exit signs, and task lighting. Ecologic, 10,000 average life hours. 82 CRI (Color Rendering Index). 120 volt, carded. Saves energy costs by replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall sconed, exit signs, and task lighting. Ecologic, 10,000 average life hours. 82 CRI (Color Rendering Index). 120 volt, carded.
Jandorf 60771 Lug Terminal WireGard 10-001 Twist-On Wire Connector CONNECTOR WIRE ASSORTMNT 158PC
Jandorf Lug Terminal, Series: 60771, 8 AWG Conductor, 5/16 in Stud, Non-Insulated Insulation, Tin Plated Copper, UL Listed Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Cone shaped springs pull wire into the connectors for a firm & secure grip. Pretwisting wires is not required. Maximum rated voltage: Grey, blue, & orange: 300 Volts; Yellow & red: 600 Volts. Neatly organized PVC storage case.
Jandorf 60770 Lug Terminal Jandorf 60768 Lug Terminal GreenGard 25-095 Grounding Wire Connector
Jandorf Lug Terminal, Series: 60770, 6 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Tin Plated Copper, UL Listed Jandorf Lug Terminal, Series: 60768, 4 AWG Conductor, 1/2 in Stud, Non-Insulated Insulation, Tin Plated Copper, UL Listed Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections.
Scotch 35 Color Coding Electrical Tape Jandorf 60774 Lug Terminal Jandorf 60775 Lug Terminal
Used in phase identification, color coding leads and piping systems and for marking safety areas. Abrasion and weather resistant, flame-retardant with excellent mechanical and electrical insulation properties. Wraps smoothly and holds tight in cold to 0 degrees F or hot to 220 degrees F. UL Listed and CSA Certified. Jandorf Lug Terminal, Series: 60774, 2/0 AWG Conductor, 1/2 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed Jandorf Lug Terminal, Series: 60775, 2/0 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed
WireGard 10-002 Twist-On Wire Connector Hex-Lok 25-2H2 Hex Lock Wire Connector Hex-Lok 25-1H1 Hex Lock Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs.
Intertape 5517 Electrical Tape LUG CU HD 4AWG 3/8IN STUD SZ  Bell Raco 5321-2 Weatherproof Box
Semi-cured rubber for low voltage electrical insulation, 30 mil. Self-vulcanizing and water resistant. Heavy-duty lugs made from pure copper for maximum current flow. Tinned for corrosion resistance. Seamless barrel for maximum strength. Closed ends seal out moisture. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Bell Raco 5321-1 Weatherproof Box Gardner Bender GSLU-70 Single Hole Mechanical Lug 3M 10457 Assortment Colored Electrical Tape Kit
Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated. Rated for 600 volt copper only. Single hole lugs, easy to install with screwdriver, wrench or pliers. 3/8" bolt size. Insulates and protects against abrasion, weather, water, solvent splashes and chemicals. Stretchy, vinyl plastic. Applications include home, marine, auto, trailers and tools. Flame retardant. Pack of 5 colors.
3M DBO/B-6 Underground Splice Kit Bell Raco 5322-0 Weatherproof Box Bell Raco 5321-5 Weatherproof Outlet Box
Designed to connect and moisture seal electrical connection for direct bury applications, 18-10 AWG, rated up to 600 volts. Combines the quick, reliable connection of a spring connector O/B with the moisture resistance of a high-impact, UV-resistant tube prefilled with moisture-resistant grease. For use with irrigation systems on golf courses, around business and for outdoor lighting systems. Application temperature range 32 - 120 degrees Fahrenheit. EU RoHS Compliant. Flame retardant. UL listed for direct bury. Weatherproof box, with lugs. Five 1/2" threaded outlets. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth x 4-1/2" length x 2-3/4" width. 18.3 cubic inch capacity. UL Listed. CSA 22.2 No. 18 NEMA 3R Rated. Constructed of die-cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box or as a housing for receptacles, switches, and GFCIs. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed. Four 1/2" threaded outlets. Complies with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. Multi-lingual instructions. 2" depth. 18.3 cubic inch capacity. 4-1/2" length x 2-3/4" width. UL Listed. NEMA 3R rated.
Hubbell 5361-0 Splice Box WingGard 25-089 Twist-On Wire Connector Spot-Gro 5330-0 Weatherproof Box
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Powder coat finish. 16.5 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. Shrink wrapped.
Bell Raco 5324-5 Outlet Box Gardner Bender HTP-1010 Self-Sealing Tape Jandorf 60776 Lug Terminal
With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Three threaded 3/4" outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed. Self-sealing silicone repair tape. Stretch, wrap, and protect or repair everything from leaky hoses, pipe insulation, electrical connections, tool handles, air ducts and cord/rope ends. Non-adhesive formula leaves no sticky residue. Waterproof and insulate with no extra equipment or heat required. Stretches up to 300 percent of its original length with 60 ppi tear strength. Begins to bond immediately on contact with itself. Repositioning is not recommended after 2 minutes of contact, and the bond is permanent within 24 hours. Operates and remains flexible from -60 degreesF (-51 degreesC) to 500 degreesF (260 degreesC). Jandorf Lug Terminal, Series: 60776, 3/0 AWG Conductor, 1/2 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed
Jandorf 60777 Lug Terminal Osram Sylvania 20415 Fluorescent Lamp WingGard 17-084 Twist-On Wire Connector
Jandorf Lug Terminal, Series: 60777, 3/0 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed Used on Bi-Pin fixtures. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
WireGard 10-003 Twist-On Wire Connector Dulux 21114 Double Tube CFL Hubbell 5361-6 Splice Box
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Double compact fluorescent lamp with 2-pin base, 3500K, 82 CRI, 1710 initial lumens, for use with electronic and dimming ballasts. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed.
LUG CU HD 2AWG 3/8IN STUD SZ  Jandorf 60769 Lug Terminal Bell Raco 5331-0 Weatherproof Box
Heavy-duty lugs made from pure copper for maximum current flow. Tinned for corrosion resistance. Seamless barrel for maximum strength. Closed ends seal out moisture. Jandorf Lug Terminal, Series: 60769, 4 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Tin Plated Copper, UL Listed With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCI's. Eight box mounting options with detachable lugs provided. Five 3/4" threaded outlets. Powder coat finish. 18.3 cubic inch capacity. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 2-3/4" width. UL Listed, CSA Approved and NEMA 3R Rated.
CONNECTOR ELEC ASSORTMNT 308PC Jandorf 60778 Lug Terminal Jandorf 60779 Lug Terminal
Tin plated copper constructed terminals & connectors provide a secure connection between two wires without soldering. Nylon cable clamps can be used for securing & organizing cables, wires, tubings, & rods. UL Listed 100% polyolefin constructed heat-shrink tubings provide an insulated and flame retardant covering for wrapping wire harnesses. Jandorf Lug Terminal, Series: 60778, 4/0 AWG Conductor, 1/2 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed Jandorf Lug Terminal, Series: 60779, 4/0 AWG Conductor, 3/8 in Stud, Non-Insulated Insulation, Brown, Copper, UL Listed
Shurtech 442055 Electrical Tape Hubbell 5323-0 Outlet Box WingGard 17-086 Twist-On Wire Connector
Self-fusing 20 mil tape, watertight seal for plumbing, auto, marine and general purpose applications. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches, and GFCIs. 5 reinforced 1/2" threaded connector outlets. Powder coat finish. Two closure plugs included. Ground screws installed. Internal threads and hubs comply with NEMA requirements. 2" depth x 4-1/2" length x 2-3/4" width. 18.3 cubic inch capacity. UL Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Bell Raco 5361-2 Splice Box Bell Raco 5361-1 Single Ended Splice Box WireGard 16-003 Twist-On Wire Connector
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Gardner Bender LTR-400 Electrical Tape Gardner Bender LTB-400 Electrical Tape TAPE LIQUID 4OZ BOTTLE WHITE
Liquid coating used to insulate and protect electrical splices and connections. Waterproof, will not unravel or deteriorate like traditional tape. Indoor/outdoor, for home, auto/marine and electrical applications. Brush-on applicator included. 4 oz. can, carded. Liquid coating used to insulate and protect electrical splices and connections. Waterproof, will not unravel or deteriorate like traditional tape. Indoor/outdoor, for home, auto/marine and electrical applications. Brush-on applicator included. 4 oz. can, carded. Liquid coating used to insulate and protect electrical splices and connections. Waterproof, will not unravel or deteriorate like traditional tape. Indoor/outdoor, for home, auto/marine and electrical applications. Brush-on applicator included. 4 oz. can, carded.
Bell Raco 5361-7 Splice Box Dulux D 20480 Double Tube CFL Raco 5372-0 Weatherproof Splice Box
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Saves energy costs bu replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall scones, exit signs, and task lighting. Ecologic, 82 CRI bulb, 6.8" overall length. For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 4" diameter x 1-1/2" depth. UL Listed. NEMA 3R Rated.
Hubbell 5361-5 Splice Box Scotch 2242 Linerless Electrical Tape Gardner Bender GSLU-125 Single Hole Mechanical Lug
For use in branch circuit wiring in wet, damp, or dry locations. Designed for use as a weatherproof junction box, and used with Bell round cluster covers and round lampholder combinations. Die cast aluminum construction. Powder coat finish. Reinforced connector outlets. Cast-in mounting lugs, four closure plugs included, and installed ground screw. 16.1 cubic inch capacity. Six 10-24 tapped holes. 4" diameter x 1-1/2" depth. UL Listed. Economical, general purpose, rubber, highly conformable, linerless Ethylene Propylene based electrical insulating tape. Weather Resistant. Uniform tape unwind, small roll size (OD). Five year shelf life. Stable over wide application and temperature range, temperature rating of 194 degrees F continuous, 266 degrees F short-term. Designed for all-voltage splicing, jacketing, and general insulating use in splicing and terminating wires and cables. Flame retardant, physical and electrical properties unaffected by degree of stretch. Provides immediate moisture seals and void free buildup. 30 mils thick, 250 psi tensile strength, 1000 percent ultimate elongation. Rated for 600 volt copper only. Single hole lugs, easy to install with screwdriver, wrench or pliers. 3/8" bolt size.
WingGard 10-084 Twist-On Wire Connector Osram Sylvania 21551 Decorative Tamper Resistant Fluorescent Lamp Dulux 21137 Single Tube CFL
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Designer warm white rare earth phosphor. Color temperature 3000K, 70 CRI, 9,000 average life hours. Single compact fluorescent lamp with 2-pin base,  ECOLOGIC for use on magnetic ballast. 10,000 average life hours.
WireGard 10-004 Twist-On Wire Connector Thomas & Betts E365DR Type T Switch Box Gardner Bender GTP-307 Electrical Tape
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Nonmetallic threaded switch box with five 1/2" threaded holes, for exposed applications with nonmetallic wiring systems only. Mounting feet included. 4" diameter. 13.5 cubic inch capacity. General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit.
Bell 5400-0 Extension Adapter Dulux D 20481 Double Tube CFL Gardner Bender 10-411 Crimp Sleeve Connector
Used to provide additional capacity needed for NEC box fill requirements. Die cast aluminum construction. 6 threaded 1/2" outlets. Installation hardware gasket and 1/2" closure plugs included. Ground screw is provided. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded 1/2" fittings and threaded conduit. 5-1/4" length x 3-1/2" width x 1-1/2" depth. UL Listed. NEMA 3R Rated. Saves energy costs bu replacing incandescent bulbs with fluorescent equivalents. Use for down lights, wall scones, exit signs, and task lighting. Ecologic, 82 CRI bulb, 6.8" overall length. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed.
WireGard 16-002 Twist-On Wire Connector Arrow Hart 1113-SP 3-Hole Weatherproof Outlet Box Plastidip LET14Z03 Electrical Tape
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Electrostatically painted with a baked, weather-resistant powder finish. Accept single gang weatherproof covers and standard FS covers. Mounting lugs provide strength and durability on any mounting surface. Raised knockout studs on back of box provide alternative means for wall mounting. Strike desired studs with sharp hammer blow for clean mounting holes. Ground screw hole located inside back wall of box. Threaded outlets for conduit and connectors. Two closure plugs and mounting lugs furnished. Three holes, one at each end and one on the back. 2" depth x 2.812" width x 4.562" length. UL Listed. Carded. A rubber insulation coating that exhibits excellent acid, alkaline, abrasion protection and seals out moisture and salt permanently. Liquid Tape has the strongest dielectric protection; 1,400 v\mil, 5-7 mils per coat. Will not harden, unravel or become brittle in extreme weather. Use to insulate cables, electronics, outdoor lighting, underground wiring, alarms, security systems, utility trailers, takes the place of electrical tape.
WingGard 16-084 Twist-On Wire Connector Gardner Bender GTP-607 All Weather Electrical Tape Gardner Bender 10-410 Crimp Sleeve Connector
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. General purpose black electrical tape. Made from low-lead PVC material. Suitable for applications up to 600 volt. Temperature range from 0 to 176 degrees Fahrenheit. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed.
Gardner Bender 10-410C Crimp Sleeve Connector Arrow Hart 1116-SP 3-Hole Weatherproof Outlet Box Hex-Lok 10-2H2 Hex Lock Wire Connector
Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed. Electrostatically painted with a baked, weather-resistant powder finish. Accept single gang weatherproof covers and standard FS covers. Mounting lugs provide strength and durability on any mounting surface. Raised knockout studs on back of box provide alternative means for wall mounting. Strike desired studs with sharp hammer blow for clean mounting holes. Ground screw hole located inside back wall of box. Threaded outlets for conduit and connectors. Two closure plugs and mounting lugs furnished. Three holes, one at each end and one on the back. 2" depth x 2.812" width x 4.562" length. UL Listed. Carded. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
Ecobulb PLF65/65 CFL Bell 5363-0 Round Weatherproof Extension Adapter WireGard 10-006 Twist-On Wire Connector
Mogul base fluorescent, 65 watt, equivalent to 300 watt incandescent. Four tube lamp, 8.75" overall length. Daylight bulb, 6500K, 4, 550 Lumens. Fits Mogul base fluorescent lights such as Cooper model AL65FL 65W Orgill SKU 084.9711. Used to provide additional capacity. Die cast aluminum construction. Includes installation hardware, closure plugs, gasket, and multi-lingual instructions.  Four 1/2" threaded outlets. Accepts all threaded 1/2" fittings and threaded conduit. 4" Round, 1-1/2" Deep. UL listed, CSA, NEMA 3R rated. Shrink wrapped. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only.
Hubbell 5400-5 Extension Box Adapter Hubbell 5337-5 Outlet Box Raco 5341-0 Square Weatherproof Outlet Box
Used to provide additional capacity needed for NEC box fill requirements. Die cast aluminum construction. 6 threaded 1/2" outlets. Installation hardware gasket and 1/2" closure plugs included. Ground screw is provided. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded 1/2" fittings and threaded conduit. 5-1/4" length x 3-1/2" width x 1-1/2" depth. UL Listed. NEMA 3R Rated. For use in branch circuit wiring in wet, damp, or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Five 1/2" threaded outlets. 31.0 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 4-9/16" width. Multi-lingual instructions. UL Listed. NEMA 3R Rated. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp, or dry locations. May be used as a weatherproof junction box or as housing for receptacles, switches and GFCI's. Eight box mounting options with detachable lugs provided. 2" deep, three 3/4" threaded outlets. 32 cubic inch capacity. Powder coat finish. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. UL Listed, CSA Approved and NEMA 3R Rated.
PushGard 10-PC3 3-Port Push-In Connector WingGard 10-086 Twist-On Wire Connector Bell Raco 5337-1 Weatherproof Box
Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. For use in branch circuit wiring in wet, damp, or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Five 1/2" threaded outlets. 31.0 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 4-9/16" width. Multi-lingual instructions. UL Listed. NEMA 3R Rated.
Bell Raco 5337-0 Infrared Brooder Weatherproof Box Bell Raco 5333-0 Weatherproof Box PushGard 10-PC4 4-Port Push-In Connector
For use in branch circuit wiring in wet, damp, or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches and GFCIs. Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Five 1/2" threaded outlets. 31.0 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 2" depth x 4-1/2" length x 4-9/16" width. Multi-lingual instructions. UL Listed. NEMA 3R Rated. With lugs. Die cast aluminum. For use in branch circuit wiring in wet, damp or dry locations. May be used as a weatherproof junction box, or as housing for receptacles, switches and GFCI's. Eight box mounting options with detachable lugs provided. Three 1/2" threaded outlets. Powder coat finish. 32 cubic inch capacity. Two closure plugs included. Ground screw installed. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and threaded conduit. 4-1/2" x 4-1/2" x 2" deep. UL Listed, CSA Approved and NEMA 3R Rated. Easy and fast, strip and push conductors into connectors to make reliable, secure connections. Simplified insertion and compact size helps in tight locations. Clear polycarbonate housings have color-coded side panels for connection verification and identification. Corrosion-resistant stainless steel springs restrict wire pullout, yet corrections are possible with a simple left-right twist and pull. Continuity test point for easy voltage checks. Rated at 600 volt maximum in building wire and at 1000 volt maximum in lighting fixtures and luminaries. Copper-to-copper connections only.
Hex-Lok 10-1H1 Hex Lock Wire Connector Gardner Bender 10-310C Crimp Sleeve Connector WingGard 10-089 Twist-On Wire Connector
Multi-range copper to copper connections only. Allows automatic or manual installation without stress whitening or distortion. Use 5/16" socket for H1. Square wire spring grabs and holds wires for secure connections. Long skirt covers stripped wires. Rated at 600 volt maximum and at 1000 volt maximum in lighting fixtures, luminaries and signs. Crimp connectors for strong, vibration-resistant permanent connections in branch circuits and fixture wiring. UL Listed. Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed.
WireGard 16-006 Twist-On Wire Connector CONNECTOR TWST WING 160JAR R/Y GreenGard 10-095 Grounding Wire Connector
Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. The swept wings provide added turning torque and reduce the strain of multiple applications. The thermoplastic shell provides strength and resistance to chemicals while a long skirt prevents exposure of bare wire. Flame-retardant properties resist heat distortion up to 105 degrees Celsius/221 degrees Fahrenheit. Rated at 600V max in building wire and at 1000V max in lighting, fixtures/luminaries and signs. The zinc-plated square wire-spring inside instantly adjusts to the shape and size of the splice upon insertion ensuring a long-lasting connection that resists corrosion and exceeds UL standards for dielectric strength and wire pullout force. Copper to copper connections only. 80 each number 86 red and number 84 yellow; 160/jar. cULus Listed. Specifically designed for making positive ground connections. Connectors feature the same live-action as WingGard connectors with the added plating protection for corrosion resistance in grounding applications. Contoured, offset wings enable firm ground connections with the twist of a hand. Flame retardant, themoplastic shell resists punctures, cuts, abrasion and corrosion. Connectors have a hole in the tip for ground wire. Solid copper to copper connections only. Nos. 15-095; 19-095 and 25-095: minimum 2 #14, maximum 4 #12 wire connections.
WingGard 16-086 Twist-On Wire Connector DryConn 10666 Twist-On Underground Wire Connector DryConn 10222 Low Voltage Dry Connector
Easy-on, easy-off without tools. Wings are knurled for a surer grip and offset from the centerline for greater twisting leverage. Easily removed for repeat usage on same size combination or larger. Expandable square-wire plated spring instantly adjusts to the shape and size of the splice for a vibration-resistant connection. Tough thermoplastic shell shields against environmental extremes. Flame-retardant, non-porous and non-corrosive shell resists surface cracking and chemical action. Temperature rating: 221 degrees F. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. Copper to copper connections only. cULus Listed. Rated for all underground direct bury applications. Use on all lighting, irrigation, and underground wiring. Additional sealant for long term service. No junction box needed. 600 volt maximum with building wire, 1000 volt in fixtures and signs. #8 to #22 wire range. UL 486D Listed. For connections exposed to condensation, water, vapors or dust. "One-step" Installation. Corrosion proof. Reduces risk of fire. UL listed and CSA certified as a pressure type connector. 600 maximum voltage with building wire, 1000 volt in fixtures and signs. Minimum #22/Maximum #12 wire range. 17/32" x 15/16".
Bell Raco 5338-0 Weatherproof Box WireGard 16-004 Twist-On Wire Connector Performance Plus O/B Twist-On Wire Connector
Outdoor electrical box, 4-1/2" x 4-1/2" x 2" deep with lugs. Seven 1/2" threaded outlets. 31.0 cubic inch capacity. For use outdoors in wet, damp or dry locations. Can be used as a weatherproof junction box, or as a housing for receptacles, switches, and GFCIs.  Die cast aluminum construction. Reinforced connector outlets. Powder coat finish. Eight box mounting options with detachable lugs provided. Two closure plugs included. Ground screw installed in box. Internal threads and hubs comply with NEMA requirements. Hubs accept all threaded fittings and conduit. Multi-lingual instructions. UL Listed. NEMA 3R Rated. Tight, square-wire spring threads directly onto conductors for fast connections with no slip. Tightens without ratcheting, easily removed for repeat usage on same size combination or larger. Fluted shell surface permits a firm grip for easy finger-tight connections. Thermoplastic shell shields against environmental extremes. Flame-retardant properties resist heat distortion up to 221 degrees Fahrenheit. Superior flash-over protection. High-dielectric shell features deep skirt design to prevent exposure of bare wire. Buttress threads screw into wire insulation. For copper to copper connections only. Designed for maintenance and repair. Replaces yellow, orange, blue and grey spring connectors. Very small shell with an increased wire range, fits easily into tight spaces. Flexible skirt helps protect workers from contact with overstripped wires. 600 volt maximum rating. 105 degrees C insulation rating. UL Listed and CSA certified.
TAPE ELECTRICAL 30FT UL       Gardner Bender HST-1300 Splice Kit CONNECTOR WIRE WNG NUM22-8 TAN
TAPE ELECTRICAL 30FT UL
Our Price: $16.34
For UF cables minimum #14/3, 12/2 maximum #8/3. Kit includes set screw splice connector and one 8" x 1.3" diameter heavy wall polyolefin heat shrink tubing. Multi-range hex-head winged twist-on connector. Minimum 3 num22, maximum 3 num10. Hex-head design strips out at UL torque saving the wires. Zinc-plated square wire spring ensures a secure connection that resists corrosion. Automatic or manual installation without stress distortion. 5/16" or 7/16" hex driver installation option. Rated at 600V max in building wire and at 1000V max in lighting, fixtures/luminaries and signs. Copper to copper connections only. cULus Listed.
Performance Plus T/R+ Twist-On Wire Connector Performance Plus R/Y+ Twist-On Wire Connector