Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL BOXES > OUTLET BOXES
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Hubbell 860 Raised Blank Utility Box Cover Hubbell 864 Utility Box Cover Hubbell 865 Utility Box Cover
Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 8752 Square Flat Blank Electrical Box Cover Hubbell 722 Octagon Flat Blank Electrical Box Cover Carlon HB1BL Blank Handy Box Cover
Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed.
Carlon HB1GF Handy Outlet Box Cover Carlon HB1SW Handy Box Cover Carlon HB1DP Handy Box Cover
Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed.
Thomas & Betts BH122A-UPC Outlet Box Hubbell 863 Utility Box Cover Raco 8977 Electrical Box Supports
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box.
Hubbell 861 Utility Box Cover Hubbell 8753 Square Flat Electrical Box Cover Hubbell 724 Octagon Flat Electrical Box Cover
Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed. Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Thomas & Betts B114R-UPC Switch Box Thomas & Betts B232A-UPC Outlet Box Hubbell 8772 Square Raised Device Box Cover
Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed.
Hubbell 703 Round Flat Ceiling Pan Cover Carlon E460R-CAR Blank Round Outlet Box Cover Carlon A400R-CAR Square Blank Electrical Box Cover
Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed. Two gang blank rise. Carlon blue color.
Raco 8768 Mud-Ring Raised Square Electrical Box Cover Halex 26279 Switch Box Support Carlon A420RR Raised Tubing Electrical Box Cover
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Use to suport attachment of an outlet box in drywall, paneling, etc., in the absence of a structure member. Installed in pairs. Suitable for paneling masonry, plaster, sheetrock, tile and all wall coverings. Brilliant electric blue. UL Listed.
Thomas & Betts B108B-UPC Outlet Box Carlon A410R-CAR Square Electrical Box Cover Thomas & Betts B108R-UPC Outlet Box
New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed. Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed.
Carlon B118B-UPC Switch Box Raco 787 Mud-Ring Flat Square Electrical Box Cover Allied Moulded 1098-N Switch Box
Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4". Steel box cover, used to mount switch or receptacle. UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
Raco 8756 Raised Square Open Electrical Box Cover Raco 871 Wall Plate Carlon A471RR Round Tubing Ceiling Box Extender with Round Cover
Raised device cover. Used to hang light fixture from 4" square box. Not designed for ceiling fan support. Angled mounting slots allow for correction of box misalignment. Raised 5/8" - ears 2-3/4" - 4 cubic inches. UL Listed. UPC bar coded. Two device switch box cover. Made from unpainted, pregalvanized steel. Used with  2 toggle 2 gang switch boxes. UL 514-A Listed, File E195978 / CSA Listed, File LR-1082. Half inch raised round high impact lightweight PVC. Used with nonmetallic sheathed cable in octagon boxes. Supports 50 pounds. UL Listed.
Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box Hubbell 731 Octagon Flat Electrical Box Cover
Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Steel box cover for one duplex receptacle. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Raco 727 Raised Octagon Open Electrical Box Cover Raco 832 Blank Flat Square Electrical Box Cover Raco 7887RAC Old Work Cable Box
Used to hang light fixture from 4" octagon box or 4" round ceiling pan. Not designed for ceiling fan support. Key-hole mounting feature allows for installation of cover without removing box screws. Raised 5/8" - 3.8 cubic inch capacity. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. 4-11/16" square. UL Listed. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Raco 791 Mud-Ring Flat Square Electrical Box Cover Hubbell 8778 Square Raised Device Box Cover Allied Moulded 1099-N Switch Box
Steel box cover, 4", used to mount two switches or receptacles. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
MUD RING 4SQ SINGLE RAISED 3/4 Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box Raco 8769 Mud-Ring Raised Square Electrical Box Cover
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Raco 8196 Electrical Box Hubbell 907C Square Exposed Work Cover
Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Used to mount two duplex receptacles on a box in surface mount application. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed.
Thomas & Betts B120R Outlet Box Raco 729 Flat Octagon Electrical Box Cover Raco 8197 Welded Electrical Box
With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8". Steel box cover for single toggle switch. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed.
Thomas & Betts BH235A Outlet Box Carlon A521DE ENT Flexible Raceway Outlet Box Hubbell 902C Square Raised Exposed Work Cover
PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed. For one duplex receptacle. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed.
Raco 8779 Mud-Ring Raised Square Electrical Box Cover Carlon SC100A 1-Gang Low Voltage Mounting Bracket Hubbell 833 Square Flat Electrical Box Cover
Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". Steel box cover with single 1/2" knockout in the center. 4-11/16" square. UL Listed.
Hubbell 803C Square Exposed Work Cover Raco 800C Raised Square Exposed Work Cover Raco 473 Gangable Switch Box
Raised 1/2". For two toggle switches. 6-1/2 cubic inch capacity. UL Listed. Used to mount one toggle switch on box in surface mount applications. Raised 1/2". 6-1/2 cubic inch capacity. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed.
Carlon E980CN-CAR Blank Weatherproof Cover Raco 915C Raised Square Exposed Work Cover Raco 809C Raised Square Exposed Work Cover
Fits Carlon single gang FS boxes. Paintable surface with textured finish to hide scratches. Stainless steel mounting screws and gasket included. UL, CSA Listed. For one GFCI receptacle and one duplex receptacle. 6.5 cubic inch capacity. UL Listed, CSA Listed. For two GFCI receptacles. 6.5 cubic inch capacity. UL Listed, CSA Listed.
Raco 906C Surface Mount Exposed Work Cover Carlon SC200RR Low Voltage Old Work Bracket Raco 528 Gangable Switch Box
For one each duplex receptacle and toggle switch. 4" square. Raised 1/2". 6.5 cubic inch capacity. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Hubbell 8500 Gangable Switch Box Carlon B418A-UPC Shallow Outlet Box Thomas & Betts B225R-UPC Outlet Box
Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16"
Raco 400 Gangable Switch Box Thomas & Betts B121ADJ Wall Box Thomas & Betts B344AB-UPC Outlet Box
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed. Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Carlon CPC4WH Blank Round Flat Outlet Box Cover Hubbell 519 Gangable Switch Box Hubbell 8531 Gangable Switch Box
Non-metallic white ceiling box cover, flat and blank. 4" diameter. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed.
Raco 404 Non-Gangable Shallow Switch Box Raco 808C Raised Square Exposed Work Cover Hubbell 471 Gangable Switch Box
Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Raised 1/2". Used to support switches or receptacles independent of the box (box must still be used). 6.5 cubic inches. UL Listed. Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed.
Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box Raco 420 Gangable Switch Box
Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed.
Raco 810C Raised Square Exposed Work Cover Raco 560 Gangable Switch Box Raco 8355 Non-Gangable Switch Box
Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle, 2.141" diameter. 6-1/2 cubic inch capacity. 4" square. UL Listed. For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed.
Raco 7488RAC Old Work Cable Box Allied Moulded 9363-EWK Old Work Switch Box Carlon E365C-CAR Blank Round Weatherproof Cover
Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Round non-metallic gray weatherproof cover. Fits T boxes.
Raco 920 Steel Bar Hangers Raco 567 Gangable Switch Box Thomas & Betts B432A-UPC Outlet Box
Holding prong, box clip holds box in place for nailing. Design resists bending and twisting. With stud. Length 14-1/4" thru 22-1/2". With locking tabs to hold bar in position. UL Listed. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Raco 976 Extension Ring Switch Box Thomas & Betts BH353A Lightweight Outlet Box Carlon E9802CN-CAR Blank Square Weatherproof Cover
Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. UV resistant, suitable for outdoor use. For use in wet or damp locations, UL Marine Listed. Non-metallic, non-corrosive, will not rust or fade. Fits two gang metallic and non metallic boxes. Includes stainless steel mounting screws and gasket. UL Listed.
Thomas & Betts SC200DV Dual Voltage Outlet Box Allied Moulded 9361-ESK Old Work Switch Box Raco 780 Mud-Ring Raised Square Electrical Box Cover
Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed.
Hubbell 518 Gangable Switch Box Thomas & Betts B232B-UPC Outlet Box Raco 223 Electrical Box
One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed.
Carlon Super Blue BH118R Old Work Outlet Box Raco 529 Gangable Switch Box Carlon A122 ENT Flexible Raceway Outlet Box
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed. Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth.
Raco 545 Non-Gangable Old Work Switch Box Raco 8211 Outlet Box Allied Moulded 2300-NK Switch Box
Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed.
Raco 508 Non-Gangable Switch Box Raco 487 Gangable Old Work Switch Box Raco 8601 Gangable Switch Box
Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed.
Raco TigerGrip 523 Gangable Old Work Switch Box Carlon Super Blue BH234R Old Work Outlet Box Thomas & Betts B355R Outlet Box
One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed. Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed.
Raco 2011FBAR Vapor Barrier Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box Raco 8235 Electrical Box
Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings. Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed.
Raco 605 Gangable Switch Box Carlon B455A-UPC Outlet Box Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed. Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5". Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed.
Thomas & Betts B234ADJ Wall Box Thomas & Betts BH464A Rigid Outlet Box Allied Moulded 9312-EWK Old Work Outlet Box
Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed.
Allied Moulded 3300-NK Outlet Box LED A19 MED E26 BASE 4.5W ORG BULB LED A19 E26 4.5W CLR GRN
Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed. Instant on to full brightness. Indoor, suitable for damp locations. Average life of 11,000 hours. Medium (E26) base. 4.25"H x 2.2"D. UL/CUL Listed, FCC and RoHS Compliant and mercury free. Clear glass LED filament light bulb. Instant on to full brightness. Vintage accent that livens up parties, homes, bars and restaurants. Uses 4.5 watts/120 volts of electricity with an average life of 20,000 hours / 18.3 years. Traditional glass design. Dimmable, 4" H x 2.3" D. UL/CUL Listed, FCC and RoHS Compliant. 100 percent mercury free.
BULB LED A19 E26 4.5W CLR RED BULB LED A19 E26 4.5W CLR BLUE Tiger Grip 517 Gangable Switch Box
Clear glass LED filament light bulb. Instant on to full brightness. Vintage accent that livens up parties, homes, bars and restaurants. Uses 4.5 watts/120 volts of electricity with an average life of 20,000 hours / 18.3 years. Traditional glass design. Dimmable, 4" H x 2.3" D. UL/CUL Listed, FCC and RoHS Compliant. 100 percent mercury free. Clear glass LED filament light bulb. Instant on to full brightness. Vintage accent that livens up parties, homes, bars and restaurants. Uses 4.5 watts/120 volts of electricity with an average life of 20,000 hours / 18.3 years. Traditional glass design. Dimmable, 4" H x 2.3" D. UL/CUL Listed, FCC and RoHS Compliant. 100 percent mercury free. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed.
Raco 878 Utility Exposed Work Cover Raco 681 Switch Box LED A19 5W/60W MED BUG LT YEL
Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle 2.141" diameter. 10.3 cubic inch capacity. UL Listed. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Instant on to full brightness, indoor, suitable for damp locations. UL/CUL Listed, FCC and RoHS Compliant and mercury free..Averages 25,000 hours life.
Carlon B468R Old Work Outlet Box Raco 8240 Electrical Box Raco 685 Switch Box
Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed.
LED G25 2.5W/25W MED DIM 2700K Raco 2002FBAR Vapor Barrier Box G25 2.5W 827 DIM LED2700K FRST
Used for bath and vanity. Instant on to full brightness. Indoor, suitable for damp locations. UL Listed, FCC Compliant, RoHS Compliant, 100 percent mercury free. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Used for bath and vanity. Instant on to full brightness. Indoor, suitable for damp locations. UL Listed, FCC Compliant, RoHS Compliant, 100 percent mercury free.
Westinghouse 8133300 Honey Swirl Light Accessory Shade LED G25 MED 4.5W 850 DIM 5000K Raco 888 Raised Square Exposed Work Cover
Honey swirl scavo shade with wide bell shape. Fitter - 2-1/4", height - 4-3/ 8", diameter - 6-7/ 8". Used for bath and vanity. Instant on to full brightness. Indoor, suitable for damp locations. UL Listed, FCC Compliant, RoHS Compliant, 100 percent mercury free. Used to mount switch or receptacle on box in surface mount applications. Raised 1/2". For one 30-60 amp, single receptacle 2.625" diameter. 10.3 cubic inches. UL Listed.
Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box Sliderbox SB Adjustable Switch/Receptacle Outlet Box Mr Heater 20381 Burner Head
Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 42 cubic inch volume, two 1/2" knockouts. Internal steel, stud/wood screws. 3-9/16" depth x 4" width x 3-3/4" height. UL listed for 2 hour fire resistive walls. For use with indoor gaslights. Replaces broken burner head or can be used with soft mantle F220353 and gasket 20339 to convert light from pre-formed mantle to soft mantle.
Thomas & Betts E989NNJ-CAR Rigid Junction Box 6.5W 2200K A19 VIN DIM MED AMB Allied Moulded 9313-EWK Old Work Switch Box
Manufactured from PVC  thermoplastic molding compound and featuring gasketed lids attached with stainless steel screws. Offers corrosion resistance and physical properties needed for direct burial applications. Intended for indoor or outdoor use, to provide a degree of protection against contact with enclosed equipment, falling dirt, hose directed water, entry of water during prolonged submersion at a limited depth, and external ice formation. UL Listed with a NEMA 6P rating per section 314.29. Indoor and outdoor use. 15,000 hours average life. Thermoset-fiberglass with ears, wing brackets, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" depth x 5-15/16" x 3-1/4". UL Listed.
Dorcy 41-1077 Portable Push and Light With Battery LIGHT LUNA TAP                BULB LED G25 DIM 4.5W 2700K
Dorcy Push and Light, Portable, 1.5 V, LED Bulb, 6 Bulbs, 5 ft Beam Distance, 24 lumens, 18 hr Average Life, Alkaline Battery, AA Battery, 4 Batteries, Press Top Lense Switch, Plastic Body, White Body, 5.51 in Overall Length, 5.51 in Overall Width, For Indoor/Outdoor Applications Two stage dimmer, 20 lumens. Uses 4 AA batteries (not included). Secure keyhole mount and drywall anchor included. Indoor and outdoor use. 15,000 hours average life.
BULB LED A15 VINTAGE 4.5W/40W COVER 3GANG RAISED 3/4 BOX 952 Rite Lite LPL595S Light Closet Push With Pull String
Indoor and outdoor use. 15,000 hours average life. Raised gang box device covers/rings are used in finish wall applications to mount switches or receptacles. Raised 3/4" for commercial wall applications. Additional keyholes allow device covers to also fit next smaller box (example: A 3-gang cover will fit a 2 or 3 gang box). 8.88" x 4.5" x .75". Super bright warm LED. On/off operation, press or pull string once for full brightness, a second time to turn the light off. Screw mount bracket. Uses 3 AA batteries.
BULB LED ST19 DIM 4.5W 2700K  Westinghouse 8186900 Light Shade BULB LED A15C VINTAGE 4.5W/40W
Indoor and outdoor use. 15,000 hours average life. Fitter - 3-1/4", diameter - 6" Indoor and outdoor use. 15,000 hours average life.
6.5W 22K ST19 VIN DIM MED CLRD LED FLAME TIP CAND 2.5W 2200K COVER 4GANG RAISED 3/4 BOX 953
Indoor and outdoor use. 15,000 hours average life. Chandelier, flame tip, candelabra base, 15000 hours average life. Used in chandeliers, lanterns and sconces. Indoor, suitable for damp locations, dimmable. Instant on to full brightness. ETL Listed, FCC Compliant, RoHS Compliant, 100 percent mercury free. Energy Star Approved. Raised gang box device cover used in finish wall applications to mount switches or receptacles. Raised 3/4" for commercial wall applications. Additional keyholes allow device covers to also fit next smaller box (example: A 4-gang cover will fit a 3 or 4 gang box). 10.69" x 4.5" x .75".
BULB LED FILAMENT 40W EQUIV   LED G16-1/2 827 4.5W DIM 2700K Westinghouse 8149400 Clip-On Shade
Candelabra base. Instant on to full brightness, suitable for damp locations.  UL/CUL Listed, FCC and RoHS Compliant and mercury free. Dimmable clear medium base G16-1/2 LED globe is a direct replacements for an incandescent bulb. Average life of 15,000 hours. Instant on to full brightness. Suitable for damp locations. UL/CUL Listed, FCC and RoHS Compliant, mercury free. 3H" x 2"D. White plastic dome. 4-1/4" height, 7-3/4" diameter.
BULB LED G25 VINTAGE 4.5W/40W BULB LED ST19 DIM 6.5W 2700K  Westinghouse 8116700 Swirl Light Shade
Indoor and outdoor use. 15,000 hours average life. Indoor and outdoor use. 15,000 hours average life. Fitter - 2 1/4", height - 5", diameter - 6".
Mr. Heater F220351 Preformed Mantle Westinghouse 8190000 Light Globe Raco 686 Switch Box
Replaces broken preformed mantles, or can be used with ceramic burner head 20338 and gasket 20339 to convert light from soft mantle to preformed mantle. Fits Paulin gas lights. White acrylic. 4" fitter, 8" diameter. Welded construction. Conduit wiring system. Two 1/2" and two 3/4" knockouts (sides). Three 1/2" and three 3/4" knockouts (bottom). Six 1/2" and six 3/4" knockouts (end). FM type bracket for wood or metal studs. 2-1/2" deep - 47.8 cubic inches. UL Listed.
MUD RING 4SQ SINGLE RAISED 1/4 Carlon E987NR Rigid Junction Box Westinghouse 8142200 Light Shade
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Manufactured from PVC  thermoplastic molding compound and featuring gasketed lids attached with stainless steel screws. Offers corrosion resistance and physical properties needed for direct burial applications. Intended for indoor or outdoor use, to provide a degree of protection against contact with enclosed equipment, falling dirt, hose directed water, entry of water during prolonged submersion at a limited depth, and external ice formation. UL Listed with a NEMA 6P rating per section 314.29. Fitter - 2-1/4", height - 4-3/4", diameter - 5-3/8"
SWITCH WRC                    LIGHT LED WRC                 Carlon E987RR Rigid Junction Box
RF technology works through walls. Auto shut-off timer. 2 AAA batteries (not included). Up to 20 remote control lights can be linked to this switch. Operates up to 60 feet and automatically shuts off the lights if they are inadvertently left on. Use alone or with wireless remote control LED lighting system. 35 lumens. 3 AA batteries (not included). Operates on its own or as an expansion to the wireless remote control lighting system. It can be paired with 19 other lights on the same remote switch. Manufactured from PVC  thermoplastic molding compound and featuring gasketed lids attached with stainless steel screws. Offers corrosion resistance and physical properties needed for direct burial applications. Intended for indoor or outdoor use, to provide a degree of protection against contact with enclosed equipment, falling dirt, hose directed water, entry of water during prolonged submersion at a limited depth, and external ice formation. UL Listed with a NEMA 6P rating per section 314.29.
LIGHT LED SENSOR BRONZE       LIGHT LED SENSOR WHITE        LIGHT CEILING MOTION ACTIVATED
Adjustable, detachable. 24 lumens, 3 AA batteries (not included). Includes a swiveling panel which aims light wherever needed, and a motion sensor. Adhesive strip and mounting bracket to install anywhere. It detaches from the back plate for handheld use. Adjustable, detachable. 24 lumens, 3 AA batteries (not included). Includes a swiveling panel which aims light wherever needed, and a motion sensor. Adhesive strip and mounting bracket to install anywhere. It detaches from the back plate for handheld use. With sensor, turns on when motion is detected and gives off 125 lumens of warm white illumination with a 30 second auto-off. Powered by 3 C batteries (not included) and has a run time of 40 hours.
Fulcrum 20043-301 Adjustable Detachable Motion Sensor Light Westinghouse 8131400 Light Shade Westinghouse 8140900 Light Shade
Fulcrum Motion Sensor Light, Adjustable, Detachable, 100 W, 6 ft Sensing, LED Lamp, 0.24 W Lamp, 4 Lamps, Battery Power, 24, ABS, Silver, For Illuminating Dark Closets, Hallways and Staircases Fitter - 2-1/4", height - 5-3/ 4", diameter - 4-7/ 8". Tapered shape. Standard 2-1/4-inch fitter.
Raco 687 Switch Box Westinghouse 8126500 Hand Painted Leaf Light Shade Raco Wiegmann SC060604RC Pull Box Enclosure
Conduit wiring system. Welded construction. FM bracket for wood or metal studs. Eight conduit knockouts (sides). Two conduit knockouts (end).  Four conduit knockouts (bottom). 63.5 cubic inch capacity. 7-19/32" wide x 2-1/2" deep. UL Listed. Hand painted glass makes each piece a unique creation. Fitter - 2-1/4", height - 5-3/8", diameter - 6". Made of 16 gauge steel. Junction boxes for terminating power or communication conductors. Boxes have flat, removal covers fastened with screws. Mounting holes in the back. Gray enamel finish.
Westinghouse 8142700 Handblown Spice Swirl Light Shade Carlon SC300PRR Electrical Box Westinghouse 8141200 Light Shade
Spice swirlglass. Tapered barrel shape, yellow shade with white swirls. Fitter 2-1/4", height 5-3/4", diameter 4-5/8" Nonmetallic ABS material is lightweight, paintable and easy to handle. Recessed low profile design provides ample room behind dry wall and between studs to accommodates cable bend requirements. Hides the wires, cables, cords and plug heads used with flat panel display installations. Has a two gang low voltage opening and a universal one gang opening for an outlet or switch box (boxes, devices, and plates not included). 4 swing out clamps lock the plate securely to the wall, horizontal or vertical mount. 2.72" depth x 5.25" width x 10.5" length. Slightly flared. Subtle white-on-white basket weave pattern. 5-7/8" high, 5-7/8" wide, 3-3/4" deep. Standard 2-1/4" fitter.
Westinghouse 8131000 Giraffe Spot Handblown Light Shade Westinghouse 8131100 Fire Pit Handblown Light Accessory Shade CAGE SHADE METAL ORB
CAGE SHADE METAL ORB
Our Price: $17.44
Handblown exotic giraffe spot shade. The tapered drum shape features a mottled giraffe spot pattern with rich brown and yellow hues that offers a vibrant centerpiece or a bright accent. Fitter - 2-1/4", height - 5-3/4", diameter - 4-1/2". Fitter - 2-1/4", height - 5-3/8", diameter - 4-7/8". Design replicating the feel of classic vintage fixtures. Add to pendant fixture for dining or bar area. Replacement shade for wall or fan fixtures and lamps requiring a neckless shade. Use for accent and mood lighting. 8? H x 6-3/4? D. Standard 2-1/4-inch fitter. Installs quickly and easily in a variety of lighting configurations. Secures with an easy-to-install shade ring (not included).
CAGE SHADE METAL BRUSHD NICKEL LED A19 MED E26 9W BLACKLIGHT Raco Wiegmann SC080804RC Pull Box Enclosure
Design replicating the feel of classic vintage fixtures. Add to pendant fixture for dining or bar area. Replacement shade for wall or fan fixtures and lamps requiring a neckless shade. Use for accent and mood lighting. 8? H x 6-3/4? D. Standard 2-1/4-inch fitter. Installs quickly and easily in a variety of lighting configurations. Secures with an easy-to-install shade ring (not included). Instant on to full brightness, indoor, suitable for damp locations. UL/CUL Listed, FCC and RoHS Compliant and mercury free..Averages 25,000 hours life. Made of 16 gauge steel. Junction boxes for terminating power or communication conductors. Boxes have flat, removal covers fastened with screws. Mounting holes in the back. Gray enamel finish.
Carlon E971FB-CAR Floor Base Box Westinghouse 8560200 Light Shade LIGHT SCONCE WALLWRC
Non-metallic PVC floor box. Water tight gasket and corrosion resistant hardware. Concrete or wood subfloor construction approved. Minimum concrete dept required is 3-1/2". Will provide optional low voltage divider permitting three services (data, telephone, and power) access. Accepts 1/2", 3/4" and 1" conduit and has PVC molded ports. Includes two 1" x 3/4", two 3/4" x 1/2" reducer plugs and two 1" and 3/4" hubs. 90 cubic inch capacity. Crystal glass. 3-1/4" fitter, 5-3/4" height, 5-1/2" diameter. Use alone or with wireless remote control LED lighting system. 55 lumens, 3 AA batteries (not included). Can be turned on manually or with a remote control switch (purchased separately). Adjustable dimmer in the light.
Westinghouse 8140500 Light Shade Raco 807C 2-Hole Raised Square Exposed Work Cover Raco 804C Blank Raised Square Exposed Work Cover
Tapered shape. Standard 2-1/4-inch fitter. For two receptacles. Two 1.406 diameter holes. 6.5 cubic inch capacity. UL Listed, CSA Listed. Used to close outlet box, blank, no holes on face. 4" square, 6.5 cubic inch capacity. UL 514-A Listed, CSA Listed.
Raco 830C 1-Hole Raised Square Exposed Work Cover Raco 831C 1-Hole Raised Square Exposed Work Cover LIGHT BAR MOTION ACT WRLS LED
For one receptacle, 2.480" diameter hole. 6.5 cubic inch capacity. UL Listed, CSA Listed. For one duplex and one 20 amp twist-lock, 1.620" diameter hole. 6.5 cubic inch capacity. UL Listed, CSA Listed. Motion activated wireless LED light bar for home, office or workshop. Light head swivels 60 degrees. Built-in motion sensor, light will turn on when motion is detected and will turn off automatically when no motion is detected after either 30 or 60 seconds. Includes screw mount bracket and screws for easy installation. On/off switch. 150 lumens. Runs on 6 AA batteries (not included). 11.75" L x 2.5" W x 1" D.
LIGHT CEILING LED MOTION      LIGHT CEILING RC LED WIRELESS LIGHT SYSTEM WRC
Motion sensor ceiling light. On/off timer. 125 lumens. 3C batteries (not included). Motion-sensitive light. Installs nearly anywhere with screws or drywall anchors (included). No wiring or plugs required. Wireless, use alone or with wireless remote control LED lighting system, remote control not included. 125 lumens. Uses 3 C batteries (not included). RF Technology works through walls. 35 lumens. Lights use 3 AA batteries (not included), Switch uses 2 CR-2032 batteries (included). Operated by a wireless remote switch which functions up to 60 feet away. Up to 20 lights can be programmed to operate on one switch. A dimmer is included, and the lights automatically turn off to save energy.
LIGHT LED LOW PRO 7IN 4000K   Westinghouse 8124200 Ruffled Crimp Edge Light Shade MOON LITE LED 4IN
MOON LITE LED 4IN
Our Price: $25.14
Round LED lamp is used in commercial office, retail, restaurant, school, hospital, multi family, and hotel/motel locations in interior hallways, bedrooms, utility/laundry rooms, living rooms, or recreational rooms. 4000K, 50,000 hours average life. UV, IR and mercury free. UL/cUL Listed for damp locations. Replacement glass, 2-1/4" fitter, 4-7/8" height, 5" diameter. Turns on with a tap and gives off 30 lumens of warm white illumination. Works on a tabletop or mounted on a wall. Powered by 3 AA batteries (not included) and has a run time of 40 hours.
LIGHT CEILING LED 750 LUMEN   Westinghouse 8561700 Light Shade FLUSH MOUNT LED 800LM 7IN
FLUSH MOUNT LED 800LM 7IN
Our Price: $27.06
Ceiling light fixture, dimmable, LED, white, installs through use of direct wire. Replacement glass, 3-1/4" fitter, 4-3/4" height, 3-5/8" diameter.
LIGHT CEILING WRC SET         FIXT FLUSH MOUNT LED INT GLOBE CEILING FIXTURE LED WH 5-1/2IN
RF technology works through walls. Up to 20 lights can be linked to the same remote control switch. 125 lumens. Switch uses 2 AA batteries (not included), light uses 3 C batteries (not included). Features a variable dimmer and an automatic battery-saving shutoff. Indoor flush mount ceiling fixture, white finish, white opal hand blown glass globe. 7-1/4" x 5-13/16". Traditional design. Dimmable when used with a compatible dimming switch. 620 lumens. 8 watts, equivalent to one 60-watt incandescent bulb. 50,000 average rated hours. ETL/CETL listed, ENERGY STAR qualified.
CEILING FIXTURE LED BN 5-1/2IN LIGHT PUFF SQ LED 11.5IN 1100L Thomas & Betts B121BFBRR Adjustable Floor Box
Ceiling light fixture, dimmable, LED, white, installs through use of direct wire. Duplex outlet with ABS cover and dual hinge caps to keep out dust. Adjusts from 0" to 1-7/8", 21 cubic inch capacity. UL Listed 5274 and classified 2HR W/C. UL514C scrub water tested. Patented residential design.
FIXT CEIL FLUSH MOUNT LED BN  LIGHT PUFF RND LED 13IN 1500 L