Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL BOXES
Choose a sub category:
OUTLET BOXES PVC SWITCH BOXES UTILITY BOXES
OCTAGON BOXES CEILING BOXES BOX COVERS
ELEC BOX SUPPORTS SPECIALTY BOXES
Sort By:
1
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Hubbell 860 Raised Blank Utility Box Cover Hubbell 864 Utility Box Cover Hubbell 865 Utility Box Cover
Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 8752 Square Flat Blank Electrical Box Cover Hubbell 722 Octagon Flat Blank Electrical Box Cover Carlon HB1BL Blank Handy Box Cover
Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed.
Carlon HB1GF Handy Outlet Box Cover Carlon HB1SW Handy Box Cover Carlon HB1DP Handy Box Cover
Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed.
Thomas & Betts BH122A-UPC Outlet Box Hubbell 863 Utility Box Cover Raco 8977 Electrical Box Supports
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box.
Carlon B112HB Handy Box Hubbell 8660 Utility Box Hubbell 861 Utility Box Cover
PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed.
Hubbell 8753 Square Flat Electrical Box Cover Hubbell 724 Octagon Flat Electrical Box Cover Thomas & Betts B114R-UPC Switch Box
Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed. Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed.
Thomas & Betts B232A-UPC Outlet Box Thomas & Betts B520A-UPC Ceiling Box Hubbell 8772 Square Raised Device Box Cover
New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4". With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed.
Hubbell 703 Round Flat Ceiling Pan Cover Carlon E460R-CAR Blank Round Outlet Box Cover Hubbell 8192 Outlet Box
Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed. Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code.
Carlon A400R-CAR Square Blank Electrical Box Cover Raco 8768 Mud-Ring Raised Square Electrical Box Cover Halex 26279 Switch Box Support
Two gang blank rise. Carlon blue color. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Use to suport attachment of an outlet box in drywall, paneling, etc., in the absence of a structure member. Installed in pairs.
Carlon A420RR Raised Tubing Electrical Box Cover Thomas & Betts B108B-UPC Outlet Box Carlon A410R-CAR Square Electrical Box Cover
Suitable for paneling masonry, plaster, sheetrock, tile and all wall coverings. Brilliant electric blue. UL Listed. New work applications, shallow PVC switch box. Integral brackets. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed.
Thomas & Betts B108R-UPC Outlet Box Carlon B118B-UPC Switch Box Hubbell 127 Octagon Box
Designed and listed for use with non-metallic sheathed cable. With mounting ears. Permissible for use with 90 degree C connectors. 8 cubic inch capacity. 1-1/4" depth x 2-3/8" x 3-5/8". UL Listed. Safe, non-conductive. With bracket for 3/8" to 5/8" wallboard. Steel and wood studs, 4 knockouts. 2-15/16" depth x 3-3/4" x 2-1/4". Two 1/2" and two 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Raco 787 Mud-Ring Flat Square Electrical Box Cover Allied Moulded 1098-N Switch Box Raco 8756 Raised Square Open Electrical Box Cover
Steel box cover, used to mount switch or receptacle. UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed. Raised device cover. Used to hang light fixture from 4" square box. Not designed for ceiling fan support. Angled mounting slots allow for correction of box misalignment. Raised 5/8" - ears 2-3/4" - 4 cubic inches. UL Listed. UPC bar coded.
Raco 871 Wall Plate BOX OCTAGON 4IN 1-1/2IN DEEP  Carlon A471RR Round Tubing Ceiling Box Extender with Round Cover
Two device switch box cover. Made from unpainted, pregalvanized steel. Used with  2 toggle 2 gang switch boxes. UL 514-A Listed, File E195978 / CSA Listed, File LR-1082. Four 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Half inch raised round high impact lightweight PVC. Used with nonmetallic sheathed cable in octagon boxes. Supports 50 pounds. UL Listed.
Carlon B1EXT-CRD Electrical Box Thomas & Betts SC100RR Low Voltage Box Allied Moulded P241 Switch Box
Extends an existing box by 1-1/8". Used to correct problems from remodeling where the wall surface is extended. Fits between the wiring device and the wall surface. Extends the switch or outlet box to flush with the wall. Works with all standard wiring devices. 2-1/4" x 3-1/4". UL Listed. For telecommunications and other low voltage wiring. Suitable for old work applications. 1.18" depth x 2.18" x 3.05". Residential thermoplastic switch or receptacle box. With angled nails. 3-9/16" depth x 2-1/4" width x 3-3/4" height. 24 cubic inch volume. Fire rating classification of 2 hours in wall and ceiling. UL Listed.
Raco 727 Raised Octagon Open Electrical Box Cover Hubbell 731 Octagon Flat Electrical Box Cover Raco 8190 Outlet Box
Used to hang light fixture from 4" octagon box or 4" round ceiling pan. Not designed for ceiling fan support. Key-hole mounting feature allows for installation of cover without removing box screws. Raised 5/8" - 3.8 cubic inch capacity. UL Listed. Steel box cover for one duplex receptacle. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mudring/cover installation. Twelve 1/2" conduit knockouts (sides). Four 1/2" conduit knockouts (bottom). No bracket. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Raco 8189 Ceiling Outlet Box Raco 832 Blank Flat Square Electrical Box Cover Raco 7887RAC Old Work Cable Box
Welded square steel box, no bracket, installed in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices.  TKO 1/2" and 3/4" eccentric knockouts (Per U.L. 514-A, suitable for use without a bonding jumper in circuits above or below 250 volts).  Eight 1/2" and 4, TKO side knockouts, two 1/2" and 2 TKO bottom knockouts. Combination cover screw heads provide for faster mud ring/cover installation. UL 514-A Listed, File E195978. 21.0 cubic inch capacity. Acceptable for use in 2-hour rated walls. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. 4-11/16" square. UL Listed. Plaster ears, old work swing style clips secure box in wall. Integral clamps. Two hour fire rated. Mounting clips. 3" depth. 14.0 cubic inch capacity. UL Listed.
Raco 791 Mud-Ring Flat Square Electrical Box Cover Hubbell 8778 Square Raised Device Box Cover Allied Moulded 1099-N Switch Box
Steel box cover, 4", used to mount two switches or receptacles. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Thermoset-fiberglass, with angled mid-nails. Nails are installed as fastening devices. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. UL Listed.
MUD RING 4SQ SINGLE RAISED 3/4 Hubbell 8650 Welded Utility Box Carlon Flex-Plus A58381D-CAR ENT Flexible Raceway Switch Box
Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed.
Raco 8769 Mud-Ring Raised Square Electrical Box Cover Carlon Flex-Plus A58381E-CAR ENT Flexible Raceway Switch Box Carlon B518A-UPC Ceiling Box
Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Non-metallic, non-conductive. Punch type knockout. Quickly connects. Square, fits commercial and residential requirements. For 600 volt use in ceilings, floors, and walls in commercial, industrial and residential buildings not more than three floors above grade. Colored in brilliant electric blue. 3" x 2-1/4" x 1-7/8". UL Listed. With captive nails. 18 cubic inch volume. Listed for fixture support up to 50 lb. 3" diameter x 2-3/4" depth. Meets NEMA OS-2, UL Listed.
Raco 8196 Electrical Box Carlon A615DE-CAR Flexible Raceway Ceiling Box Hubbell 8670 Welded Utility Box
Six 1/2" and 3 TKO conduit knockouts (sides). Three 1/2" and 2 TKO conduit knockouts (bottom). Combination cover screw heads provide for faster mudring/cover installation. FM bracket mounts flat on side of stud and provides a rigid, secure box installation. Square boxes are installed in ceiling or walls for lighting fixture or receptacles. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Safe, non-conductive. Quick connect. 20.5 cubic inch capacity. Knockouts 1/2" x 3/4". 4" diameter x 2-1/8" depth. Welded design allows for more working room inside box. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). Acceptable for use in 2-hour rated walls. UL Listed.
Raco 8197 Welded Electrical Box Hubbell 907C Square Exposed Work Cover Thomas & Betts B120R Outlet Box
Square 4" steel box for lighting fixtures, switches or receptacles where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 1-1/2" deep. 21.0 cubic inch capacity. Welded, with six 1/2" and three TKO  side knockouts, three 1/2" and two TKO  bottom knockouts. Flush FH bracket type for side mount of stud and features hooks that drive into face of wood stud for hands-free installation. UL Listed. Used to mount two duplex receptacles on a box in surface mount application. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed. With mounting ears and swing bracket. 4 integral clamps, 2 each end. UL Listed, meets NEMA OS-2. Suitable for masonry walls, not UL Classified for Fire Resistance. PVC construction. 20 cubic inch capacity. 3-5/8" depth x 2-5/16" x 4-1/8".
Hubbell 146 Octagon Box Raco 662 Drawn Utility Box Thomas & Betts B618RR Ceiling Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Used in the installation of ceiling or wall lighting fixtures or as a junction box. 1-1/2" deep, 15.5 cubic inch capacity. 50 pound maximum recommended static load. Not designed for ceiling fan support. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. Handy box, used for convenience outlet, switch box or small junction box. Three 1/2" knockouts (sides). Two 1/2" knockouts (ends). Three 1/2" knockouts (bottom). "TS" bracket for wood or metal studs. Gauging tabs and recessed nailing spur. 4" x 2" x 1-7/8" deep. 13.0 cubic inches. Round old work box with 4 integral swing clamps. Three zip mount retainers. High temperature resistant. 4-1/4" diameter x 2-3/4" depth. UL Listed.
Raco 653 Utility Box Raco 729 Flat Octagon Electrical Box Cover Thomas & Betts BH235A Outlet Box
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides). Two 1/2" knockouts (end). 4" x 2" x 1-1/2" deep. 11.5 cubic inches. UL, CSA Listed. Steel box cover for single toggle switch. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. 35 cubic inch rigid wall.
Carlon B520P-UPC Ceiling Box Carlon A521DE ENT Flexible Raceway Outlet Box Hubbell 902C Square Raised Exposed Work Cover
Ceiling box with captive nails, ground lug and screw attached. Fixture spacing for 2-3/4" and 3-1/2". 6 integral clamps. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. UL Listed. Meets NEMA OS-2. Non-metallic. Non-conductive. Suitable for masonry walls. 4" x 4" x 1-1/2". 1/2" and 3/4" knockouts. UL Listed. For one duplex receptacle. Raised 1/2". 6-1/2 cubic inch capacity. 4" square. UL Listed.
Hubbell 665 Utility Box Extension Ring Raco 8779 Mud-Ring Raised Square Electrical Box Cover Carlon Super Blue BH525A-UPC Ceiling Box
Used to add additional wiring capacity to handy box. Six 1/2" knockouts (sides) and two 1/2" knockouts (ends). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. Rigid polycarbonate box used for decorative light fixtures or low voltage devices. Made of a heat resistant thermoplastic material that is lightweight, noncorrosive and nonconductive. Captive nails, 25 cubic inch, 3" deep, large capacity boxes are perfect for specialty lighting, track lighting, or smoke/security devices. Listed for fixture support up to 50 lb. Includes mounting hardware. UL Listed.
Carlon SC100A 1-Gang Low Voltage Mounting Bracket Raco 110 Electrical Box Hubbell 833 Square Flat Electrical Box Cover
Backless bracket with nail on mounting and screw in bracket. Non-metallic. Non-conductive. 3.73" x 2.32". Octagon box, 3-1/2" with four 1/2" side conduit knockouts and one 1/2" bottom conduit knockout. Drawn construction, can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code. Steel box cover with single 1/2" knockout in the center. 4-11/16" square. UL Listed.
Hubbell 8663 Utility Box Hubbell 803C Square Exposed Work Cover Raco 800C Raised Square Exposed Work Cover
Drawn construction and raised grounding provision for surface mount applications. Four 3/4" knockouts (sides). Two 3/4" knockouts (ends). One 3/4" knockout (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Raised 1/2". For two toggle switches. 6-1/2 cubic inch capacity. UL Listed. Used to mount one toggle switch on box in surface mount applications. Raised 1/2". 6-1/2 cubic inch capacity. UL Listed.
Raco 473 Gangable Switch Box Carlon E980CN-CAR Blank Weatherproof Cover Raco 915C Raised Square Exposed Work Cover
Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Beveled corners prevent the clamp screws from protruding into the back wall. With nonmetallic sheathed cable clamps. Acceptable for use in 2-hour fire rated walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). 1/2" conduit knockouts (bottom). With leveling bumps. No plaster ears, not suitable for old work.  2-1/4" deep - 10.5 cubic inches. UL Listed. Fits Carlon single gang FS boxes. Paintable surface with textured finish to hide scratches. Stainless steel mounting screws and gasket included. UL, CSA Listed. For one GFCI receptacle and one duplex receptacle. 6.5 cubic inch capacity. UL Listed, CSA Listed.
Raco 809C Raised Square Exposed Work Cover Hubbell 8232 Outlet Box Hubbell 130 Octagon Box Extension Ring
For two GFCI receptacles. 6.5 cubic inch capacity. UL Listed, CSA Listed. Conduit wiring system. Eight 1/2" and four TKO conduit knockouts (sides). Two 1/2" and two TKO conduit knockouts (bottom). 4" square x 2-1/8" deep, 30.3 cubic inch capacity. Combination cover screw heads provide for faster mudring/cover installation. No bracket, installed in ceilings or walls for lighting fixtures and receptacles. Acceptable for use in 2-hour rated fire walls. With UPC bar code. UL Listed. Two 1/2" and two 3/4" conduit knockouts (sides). Extension rings provide a means for adding additional cubic capacity or as and outlet box for surface conduit.
Raco 906C Surface Mount Exposed Work Cover Carlon Super Blue BH614R Old Work Ceiling Fan Box Carlon SC200RR Low Voltage Old Work Bracket
For one each duplex receptacle and toggle switch. 4" square. Raised 1/2". 6.5 cubic inch capacity. UL Listed. Spring metal mounting brackets. Fixture rating limit of 10 pounds. Heat resistant. 3-1/2" diameter round old/new work box base, ears and snap-in bracket. UL Listed. For installation of low-voltage devices in an existing wall. Thinner rectangular flange for faster, easier installation, less protrusion on the wall. Shallow bracket means less material, easier to work with. Can be installed vertically or horizontally. UL listed.
Raco 8292 Ceiling Pan Box Raco 528 Gangable Switch Box Raco 161 Drawn Electrical Box
Non-metallic sheathed cable wiring system. Clamps in bottom. Four cable knockouts, one 1/2" conduit. 3-1/2" diameter x 1/2" depth. UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. Leveling bumps. Less ears. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Drawn metal 4" octagon box used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. Maximum recommended support load for a  static fixture is 50 lb. TS bracket for wood or metal studs features gauging tabs and recessed nailing spurs. 1-1/2" depth, 1/2" bracket setback, three 1/2" side knockouts, five 1/2" bottom knockouts. 15.5 cubic inch capacity. Combination screw heads allow for fast cover or fixture installation. Acceptable for use in 2-hour rated walls and ceilings. UL Listed.
Hubbell 8500 Gangable Switch Box Carlon B418A-UPC Shallow Outlet Box Thomas & Betts B225R-UPC Outlet Box
Conduit wiring system. Four 1/2" conduit knockouts (sides). Two 1/2" conduit knockouts (end). Two 1/2" conduit knockouts (bottom). Less clamps. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed. With mounting ears and 2 swing clamps. Suitable for masonry walls, UL Listed, not UL Classified for fire resistance. 2-3/4" depth x 3-1/8" x 3-15/16"
Carlon Super Blue BH525P Ceiling Box Raco 661 Handy Box Raco 400 Gangable Switch Box
Combination ceiling box, hard shell with captive nails and grounding lug. 3" depth. Listed for fixture support up to 50 lb. 4.062" diameter x 3" depth. UL Listed. Three 1/2" knockouts (sides). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. "A" style bracket for wood or metal, positions handy box securely against face and side of stud. Acceptable for use in 2-hour rated walls. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. 1-1/2" deep - 7.5 cubic inches. UL Listed.
Thomas & Betts B121ADJ Wall Box Hubbell 8293 Ceiling Pan Box Thomas & Betts B344AB-UPC Outlet Box
Provides simple installation and allows adjustment from 0 to 1-3/4" with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3-3/8" depth x 3-7/8" x 3-3/4". Permissible for use with 90 degree C connectors. Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Five 1/2" bottom conduit knockouts, 6 cubic inch capacity. Acceptable for use in 2-hour rated walls and ceilings. 4" diameter x 1/2" depth. UL Listed. With captive nails and bracket support, twelve integral clamps, six each side. 44 cubic inch capacity,  2-11/16" depth x 3-3/4" x 5-5/8". Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Carlon CPC4WH Blank Round Flat Outlet Box Cover Hubbell 519 Gangable Switch Box Hubbell 8531 Gangable Switch Box
Non-metallic white ceiling box cover, flat and blank. 4" diameter. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed.
Raco 404 Non-Gangable Shallow Switch Box Raco 808C Raised Square Exposed Work Cover Hubbell 471 Gangable Switch Box
Shallow switch box, made for use with furring strips and 1/4" paneling. Welded, with nonmetallic sheathed cable clamps. Two cable knockouts (end). One 1/2"' conduit knockout (end). D bracket for wood or metal studs. 1/4" bracket setback. 1" deep - 6.5 cubic inches. UL Listed. Raised 1/2". Used to support switches or receptacles independent of the box (box must still be used). 6.5 cubic inches. UL Listed. Beveled corner box, designed to prevent the clamp screws from protruding into back wall. Non-metallic sheathed cable clamps. Acceptable for use in 2-hour rated walls. Four cable knockouts (end). One 1/2" conduit knockout (bottom). No bracket, clamp screws through beveled corners. With ears. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. UL Listed.
Hubbell 410 Non- Gangable Switch Box Carlon B117RSW Old Work Shallow Outlet Box Hubbell 167 Octagon Box
Four cable knockouts on the end. 3" x 2" x 1-1/2" deep. 7.5 cubic inches. With clamps for non-metallic sheathed cable. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. UL Listed. Shallow box, flanged, non-metallic and non-conductive. 2" depth x 4-1/4" width x 4" length. Two 1/2" and two 3/4" conduit knockouts (sides). Three 3/4" and two 1/2" conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code.
Allied Moulded 9318 Handy Box Raco 420 Gangable Switch Box Raco 810C Raised Square Exposed Work Cover
Thermoset-fiberglass handy box. Surface mounted, with side and bottom romex cable openings. 2" depth x 2-1/4" width x 4-3/16" height. UL Listed. Gangable 3" x 2" switch box, offers the option of constructing a box to hold two or more devices. Plaster ears allow the box to be used in old work applications. Acceptable for use in 2-hour fire rated walls. Four 1/2" conduit knockout (sides). Two 1/2" conduit knockout (end). Two 1/2" conduit knockouts (bottom). 2" deep - 10.0 cubic inches. UL Listed. Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle, 2.141" diameter. 6-1/2 cubic inch capacity. 4" square. UL Listed.
Raco 560 Gangable Switch Box Raco 8355 Non-Gangable Switch Box Raco 674 Handy Box
For conduit. 3" x 2" switch box. No bracket, adjustable plaster ears allow box to be used in old work applications. 14.0  cubic inch capacity, 2-3/4" deep, four 1/2" side knockouts, two 1/2" bottom knockouts and two 1/2" end knockouts. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (ends). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. "S" backset. Mounting guides set 3/8", with bumps. Angle nail type. 3" x 2" x 2-27/32" deep, 15.8 cubic inch capacity. Prepositioned mounting nails included. Acceptable for use in 2-hour rated walls. UL Listed. For convenience outlets, switch boxes or small junction boxes for exposed work applications. 4" x 2", with four 3/4" conduit knockouts (sides), two 3/4" conduit knockouts (bottom) and two 3/4" knockouts (end). 4" height x 2" width x 2-1/8" deep. 16.5 cubic inch capacity. Welded design allows for more working room inside box. UL Listed.
Raco 8201 Extension Ring Outlet Box Raco 7488RAC Old Work Cable Box Allied Moulded 9363-EWK Old Work Switch Box
For adding additional cubic capacity or as an outlet box for surface conduit. Twelve 1/2" side knockouts, drawn metal, suitable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep, 22.5 cubic inch capacity. UL Listed. Old work PVC box. With swing clips and integral clamps to hold securely. 3-5/32" depth. 25.0 cubic inch capacity. Thermoset-fiberglass with ears, wing brackets, speed clamps. 2 hour wall and ceiling fire rating. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-7/8" x 2-3/8" x 3-1/4". UL Listed.
Carlon E365C-CAR Blank Round Weatherproof Cover Raco 920 Steel Bar Hangers Thomas & Betts B620KR-UPC Ceiling Box
Round non-metallic gray weatherproof cover. Fits T boxes. Holding prong, box clip holds box in place for nailing. Design resists bending and twisting. With stud. Length 14-1/4" thru 22-1/2". With locking tabs to hold bar in position. UL Listed. Ceiling box with 14.38"-22.5" adjustable bar hanger. 4" diameter x 2-1/4" depth. Fixture spacing for 2-3/4" and 3-1/2". Integral clamps. Listed for fixture support up to 50 pounds. UL Listed.
Raco 567 Gangable Switch Box Hubbell 8203 Electrical Box Extension Ring Thomas & Betts B432A-UPC Outlet Box
Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. 3" x 2" x 2-3/4" deep. 14.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. For adding additional cubic capacity or as an outlet box for surface conduit. Eight 1/2" and four 3/4" conduit knockouts (sides). 4" square x 1-1/2" deep. 22.5 cubic inches. UL Listed. With captive nails and ten integral clamps, three top and bottom, two each side. Suitable for masonry walls. 4" x 4" square. UL Listed.
Raco 976 Extension Ring Switch Box Allied Moulded 9351-NK Outlet Box Raco 111 Extension Ring Ceiling Outlet Box
Add-A-Depth ring used to correct for a 3" x 2" switch box or 4" square box (2 needed) set too deep in a wall. Adjustment range 1/4" to 1", two 1-1/8" long screws included. UPC bar code. Ceiling box with nails, speed clamps. 50 lb. fixture rated. 2 hour wall and ceiling fire rating classification. 4" diameter x 2-3/8" depth. UL Listed. Extension rings provide a means for adding 11.8 additional cubic capacity to a box or as an outlet box for surface conduit. Not designed for ceiling fan support. Four 1/2" conduit knockouts on the sides. 50 pound maximum recommended static load. Acceptable for use in 2-hour rated walls and ceilings. 1-1/2" deep x 11.8 cubic inches. UL Listed.
Thomas & Betts BH353A Lightweight Outlet Box Carlon E9802CN-CAR Blank Square Weatherproof Cover Raco 175 Ceiling Outlet Box
Lightweight design and durable plastic. Safe to install and will never rust or corrode. Includes hardware for easy installation. Rigid wall box. UV resistant, suitable for outdoor use. For use in wet or damp locations, UL Marine Listed. Non-metallic, non-corrosive, will not rust or fade. Fits two gang metallic and non metallic boxes. Includes stainless steel mounting screws and gasket. UL Listed. With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 2-1/8" deep, 21.5 cubic inch capacity. UL Listed.
Thomas & Betts SC200DV Dual Voltage Outlet Box Allied Moulded 9361-ESK Old Work Switch Box BOX OCT 4IN 1-1/2DP NM CLAMP
Enables line voltage and low-voltage to run to the same location. Uses standard 2 gang faceplate. Backless design accommodates large/deep low voltage devices. 3.69" x 4.04". 20.5 cubic inch capacity. UL approved. Thermoset-fiberglass with ears, snap bracket, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 2-7/8" x 2-3/8" x 3-1/4". UL Listed. With non-metallic sheathed cable clamps. With ear brackets. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. 1-1/2" deep, 15.5 cubic inch capacity. Acceptable for use in 2-hour fire rated walls. UL Listed.
Raco 164 Electrical Box Raco 780 Mud-Ring Raised Square Electrical Box Cover Hubbell 518 Gangable Switch Box
Four cable pryouts and one 1/2" KO side, one - 1/2" KO bottom. Octagon boxes are used in the installation of ceiling or wall light fixtures. TS bracket features gauging tabs and recessed nailing spurs, for wood or metal studs. Acceptable for use in 2-hour fire rated walls and ceilings. 1-1/2" deep - 15.5 cubic inches. UL Listed. UPC bar code. Used to close outlet box. For mounting switches or receptacles. Size 4", UL Listed. One 1/2" bottom conduit knockout, four bottom cable knockouts. With armored cable/metal clad/flex clamps. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. 2-1/2" deep - 12.5 cubic inches. UL Listed. UPC bar coded.
Hubbell 160 Octagon Box Thomas & Betts B232B-UPC Outlet Box Raco 112 Electrical Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed. With bracket for 3/8" to 5/8" wallboard steel or wood stud mounting and 8 integral clamps, 4 each side. 3-3/4" x 4" x 3". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Octagon boxes can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 1-1/2" deep, 11.8 cubic inch capacity. UL Listed, acceptable for use in 2-hour fire rated walls.
Raco 223 Electrical Box Carlon Super Blue BH118R Old Work Outlet Box Raco 529 Gangable Switch Box
Four cable knockouts (sides). Two 1/2" and one TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With non-metallic sheathed cable clamps. FM flush side-mount bracket for wood or metal studs. Square boxes are installed in ceilings or walls for lighting fixtures or receptacles. Acceptable for use in 2-hour fire rated walls. 4" square x 1-1/2" deep - 21.0 cubic inches. UPC bar code. UL Listed. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 2.41". UL Listed. Four cable knockouts (end). Two 1/2" conduit knockouts, (end). One 1/2" conduit knockout (bottom). "LB" bracket for wood studs, 5/8" offset to clear narrow door molding. Face mounts on front edge of wood stud. Use when space between studs is limited. With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. UL Listed.
Carlon A122 ENT Flexible Raceway Outlet Box Raco 545 Non-Gangable Old Work Switch Box Raco 8211 Outlet Box
Eccentric knockouts, non-metallic and non-conductive. Can be mounted to wood or steel studs. 3.53" height x 2.10" width x 3.25" depth. Four cable knockouts (end). Two 1/2" knockouts (end). With NMSC, non-metallic sheathed cable clamps. Old work clip. 3" x 2" x 2-1/2" deep - 12.5 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Four cable knockouts (sides). Four 1/2" and two TKO conduit knockouts (sides). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. Square boxes are used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. 4" square x 1-1/2" deep - 21.0 cubic inches. UL Listed, acceptable for use in 2-hour fire rated walls. UPC bar code.
Allied Moulded 2300-NK Switch Box Raco 295 Ceiling Fan Box Raco 508 Non-Gangable Switch Box
Thermoset-fiberglass, with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 4" x 3-3/4". UL Listed. Ceiling fan 4" round pan, 1/2" deep, 6 cubic inches, 5 bottom 1/2" knockouts. Used for new work and renovations. Ceiling fan rated, used in the installation of heavy light fixtures or ceiling fans. Maximum 70 pound fan or 150 pound fixture. Includes nonmetallic sheathed cable connector, mounting hardware, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed. Two 1/2" conduit knockouts (end). Old work clips. Provided U box support eliminates the need for additional box supports to secure box in wall opening. For 3/4" sheetrock maximum thickness. Acceptable for use in 2-hour fire rated walls. 12.5 cubic inches. 3" x 2" x 2-1/2" deep. UL Listed.
Hubbell 8257 Welded Outlet Box Raco 487 Gangable Old Work Switch Box Raco 8601 Gangable Switch Box
Conduit wiring system. Two 1/2" and twelve TKO conduit knockouts (sides). One 1/2", three TKO conduit knockouts (bottom). No bracket, installed in ceilings or walls for lighting fixtures or receptacles. 4-11/16" square x 2-1/8" deep - 42.0 cubic inches. Combination cover screw heads provide for faster mudring/cover installation. UPC bar code. UL Listed. Four cable knockouts (end). One 1/2" conduit knockout (bottom). Clamp screws through beveled corners. With clamps for non-metallic sheathed cable. Adjustable plaster ears allow box to be used in old work applications. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. 3" x 2" x 2-1/4" deep. 10.5 cubic inches. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). With non-metallic cable clamps in each end. 3" x 2" x 3-1/2" deep. 18.0 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated walls. UL Listed.
Thomas & Betts B708-SHK Ceiling Pan Box Raco TigerGrip 523 Gangable Old Work Switch Box Carlon B620HG-UPC Ceiling Box
Shallow ceiling fan outlet box with mounting screws. 1 integral clamp. Non-conductive high impact lightweight PVC. 5 knock outs, 8 cubic inch capacity. For new work or renovations. Mounts ceiling fan securely to the ceiling joist. Rated for fans up to 35 pounds and fixture up to 50 pounds. 4" diameter x 5/8" depth. UL Listed. One 1/2" bottom knockout. Four cable knockouts. 2-1/2" deep x 12.5 cubic inches. Armored cable/metal clad/flex clamps. Old work clips on side of box eliminates the need for additional box supports to secure box in wall opening. Acceptable for use in 2-hour rated walls. UL Listed. UPC bar coded. Non-metallic sheathed cable clamps. Ceiling box with 14 -1/4" - 23-1/2" adjustable bar hanger. Fixture spacing for 2-3/4" and 3-1/2". 4" diameter x 2-1/4" depth. Ground lug and screw. 6 integral clamps. Listed for fixture support up to 50 lb. UL Listed, meets NEMA OS-2.
Carlon Super Blue BH234R Old Work Outlet Box Thomas & Betts B355R Outlet Box Raco 2011FBAR Vapor Barrier Box
Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and molded-in swing clamps to make installation faster. Designed to nest inside one another to take up less shelf space and are easier to transport to job sites. 3.85" x 4.17". UL Listed. Extra large box. 6 clamps to hold cable, swing out clamps to hold to the wall. Engraved with NEC approved conductor fill. 13" x 6.25" x 8". UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs.
Sliderbox SB Adjustable Switch/Receptacle Outlet Box Raco 8235 Electrical Box Raco 605 Gangable Switch Box
Molded of engineering grade non-metallic thermoplastic. Adjustable, no need to remove or relocate mounting screws to re-position the box. Slots retain slider plate and guide it in a straight motion. Internal rails guide slider plate for smooth mounting adjustability in wall substrates from 1/2" to 1-3/8" thick and ceiling substrates from 1/2" to 1-5/32". Square corner design allows easy wall cut-in (Old work applications). Molded spline device holes for quick device screw installation. 23 cubic inch volume, 1/2" knockout. Internal steel, stud/wood screws. 3-9/16" depth x 2-1/4" width x 3-3/4" height. UL Listed for 2 hour fire resistive walls and ceilings. Installed flush in ceilings or walls for lighting fixtures, switches or receptacles, used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Combination cover screw heads for faster mud ring/cover installation. TS bracket for wood or metal studs, features gauging tabs and recessed nailing spurs. Fixture support of 6 lb. maximum. 30.3 cubic inch capacity 4" square x 2-1/8" depth with 6 eccentric 1/2" and 3 TKO side knockouts and 3 eccentric 1/2" and 2 TKO bottom knockouts. Acceptable for use in 2-hour fire rated walls. UL Listed. Four 1/2" conduit knockouts (sides). Four cable knockouts (end). Two 1/2" conduit knockouts (end). One 1/2" conduit knockout (bottom). 3" x 2" x 3-1/2" deep. 18.0 cubic inches. With clamps for non-metallic sheathed cable. "TS" brackets for wood or metal studs. Gauging tabs and recessed nailing spur. Side mount. UL Listed.
Carlon B455A-UPC Outlet Box Carlon Super Blue BH525H Ceiling Box Saf-T-Cap 0105000 Outlet Ceiling Fan Box
Safe, non-metallic, non-conductive. Molded instructions. 12 integral clamps, 6 each side. Bracket and captive nails included. 2-1/2" depth x 3-7/10" x 7-3/5". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. 4" diameter x 2.95" depth. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wirefill capacity, and comes with molded-in nailing flanges and clamps to make installation faster. Listed for fixture support up to 50 lb. Hanger bar adjusts from 11-1/2" to 18-1/2". UL Listed. For new construction or applications where attic is accessible. Fits all ceiling fans. Maximum load rating for ceiling fans is 70 pounds. 100 pounds for fixtures. 8-32 threads for lightweight fixtures, 10-24 threads for ceiling fans. 3 knockouts for conduit or Romex. 2 Romex clamps. 1-1/2" deep, 15.5 cubic inch capacity. Includes SAF-T-CAP and mounting screws. UL Listed.
Raco Romex 176 Electrical Box Carlon Adjust-A-Box MB120ADJ Adjustable Switch Box Thomas & Betts E981DFN-CTN Rigid Type FSC FS Switch Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts, (sides). One 1/2" conduit knockout, (bottom). Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 pound maximum recommended static load. J side-mount bracket with spurs and holes for toe-nailing, for wood studs or joists. UPC bar code. UL Listed. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Safe, non-conductive, takes standard covers and accessories. For through terminations. With detachable mounting feet. 19 cubic inch capacity.
Raco 8265 Ceiling Outlet Box Thomas & Betts E980EFN-CTN Rigid Type FSC FS Switch Box Thomas & Betts E980DFN-CTN Rigid Type FSC FS Switch Box
Conduit wiring system. Welded, with conduit knockouts. Four 3/4" and four 1" conduit knockouts (sides). One 1/2" conduit knockout and three TKOs (bottom). 4-11/16" square x 2-1/8" deep. 42.0 cubic inches. Installed in ceilings or walls for lighting fixtures or receptacles. UPC code. UL Listed. Safe, non-conductive. For dead-end terminations. With integral mounting feet. Will not rust or corrode. 18 cubic inch capacity. UL Listed. Safe, non-conductive. For dead-end terminations. With integral mounting feet. Will not rust or corrode. 18 cubic inch capacity. UL Listed.
Thomas & Betts B234ADJ Wall Box Thomas & Betts E981EFN-CTN Rigid Type FSC FS Switch Box Thomas & Betts B720R-SHK Ceiling Fan Box
Patented design provides simple, goof-proof installation and allows the installer to adjust the box to any thickness with the turn of a screw. Clip the included bracket onto any stud, mounts square and secure every time. Securing the bracket to the stud ensures that the box will not move. Comes preset at 1/2". 3" depth x 5-5/8" x 3-5/8". Satisfies NEC 370-20. UL Listed 5Z74 and classified 2 Hr W/C. Safe, non-conductive, takes standard covers and accessories. For through terminations. With detachable mounting feet. 19 cubic inch capacity. Non-conductive high impact lightweight PVC. Full 20 cubic inch capacity. 6 integral clamps. 4" diameter x 2-1/4" depth. Used for new work or renovations. Rated for fans up to 35 pounds and fixture up to 50 pounds. Mounts fan to a cross member secured between ceiling joist. Mounting screws included. UL Listed.
Thomas & Betts BH464A Rigid Outlet Box Allied Moulded 9312-EWK Old Work Outlet Box Raco 296 Ceiling Fan Box
Rigid wall box. Lightweight design and durable plastic. Safe to install and will never rust or corrode. Allows for large wiring devices (GFIs and dimmers). Includes hardware for easy installation. Thermoset-fiberglass, with ears, wing brackets and speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2-3/4" depth x 4-1/8" x 3-1/4". 2 hour wall fire rating. UL Listed. Ceiling fan box, 4" octagon, 1-1/2" deep. 3 bottom 1/2" knockouts. Used in new work and renovations. Ceiling fan rated octagon boxes can be used in the installation of heavy light fixtures or ceiling fans. Recommended support load for ceiling fan is 70 pounds, for fixtures is 150 pounds. Includes non-metallic sheathed cable connector, mounting hardware, high strength hardened screws, and instructions. Acceptable for use in 2-hour rated walls and ceilings. UL Listed.
Carlon Super Blue BH525HP Ceiling Box Allied Moulded 3300-NK Outlet Box Carlon E982DFN-CTN Type FS Rigid Switch Box
Ceiling box with hanger bar, adjusts from 11-1/2" to 18-1/2". Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of specially formulated, strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Listed for fixture support up to 50 lb. 4" diameter x 3" depth. UL Listed. Ground lug included. Thermoset-fiberglass with angled mid-nails, speed clamps. Lightweight, non-corrosive, non-conductive, no ground required, will not melt or distort in high heat. Shatter resistant in cold temperatures. 2 hour wall fire rating. 3" depth x 5-11/16" x 3-3/4". UL Listed. For multiple dead-end circuit terminations or where additional support is required in stub-up applications. Takes standard covers and accessories or devices. 18 cubic inch capacity.
Raco 8325 Ceiling Outlet Box Tiger Grip 517 Gangable Switch Box Carlon E982EFN-CTN Type FSS Rigid Switch Box
With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 pound maximum recommended support load. Furnished with 3/8"-18 NPS trade size fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. 1-1/2" deep - 15.5 cubic inches. Four cable knockouts (end). One 1/2" conduit knockout (bottom). With clamps for non-metallic sheathed cable. 3" x 2" x 2-1/2" deep. 12.5 cubic inches. Adjustable plaster ears allow box to be used in old work applications. Acceptable for use in 2-hour rated fire walls. UL Listed. For multiple dead-end circuit terminations or where additional support is required in stub-up applications. Takes standard covers and accessories or devices. 18 cubic inch capacity.
Raco 878 Utility Exposed Work Cover Raco 680 Switch Box Raco 681 Switch Box
Used to mount switches or receptacles on boxes in surface mount applications. Raised 1/2". For one 30-50 amp, single receptacle 2.141" diameter. 10.3 cubic inch capacity. UL Listed. Four inch square, drawn metal box, suitable for use in 2-hour fire rated walls. Conduit wiring system. Twelve 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). 2-1/8" deep - 30.3 cubic inches. UL Listed. Drawn construction for surface mount applications. Conduit wiring system. Nine 1/2" conduit knockouts (sides). Five 1/2" conduit knockouts (bottom). TS brackets, for wood or metal studs. Gauging tabs and recessed nailing spur. 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed.
Carlon B468R Old Work Outlet Box Raco 8326 Ceiling Outlet Box Thomas & Betts BH525L Ceiling Fan Box
Workbox can accommodate three and four large wiring devices. Installs easily for existing construction remodeling work. 8 clamps securely hold cable. Swing out clamps lock box securely to wall. Lightweight and durable and engraved with NEC approved conductor fill. Suitable for masonry walls. 68 cubic inch capacity, 3.41" depth x 7.57" x 2.89". With non-metallic sheathed cable clamps. Two 1/2" conduit knockouts and four cable knockouts (sides). Used to hang light fixtures between joists or structural members. Includes 4" octagon box. Not designed for ceiling fan support. 10 lb. maximum recommended support load. Furnished with 3/8"-18 NPS fixture stud. Bar hanger is adjustable from 14-1/4" to 22-1/2". Box is adjustable along entire length of bar. Acceptable for use in 2-hour fire rated walls. UL Listed. UPC bar code. New work ceiling fan box with nails and metal brace for stud finishing. Rated for fans up to 35 pounds and fixtures up to 50 pounds. 4.062" diameter x 3.06" depth. Lightweight, noncorrosive, and nonconductive, rigid, nonmetallic wiring box combines features of hard shell thermoset box and thermoplastic PVC style box. Molded of strong thermoplastic material, will not crack or break, even in extreme environments. Resists flexing and holds shape even under the worst conditions. Provides large wire capacity, and comes with molded-in nailing flanges. UL Listed.
Carlon E9802DR Type FSE Rigid Switch Box Raco 8240 Electrical Box Carlon E9802E-CTN Type FS Rigid Switch Box
For dead-end terminations where two devices or additional wiring capacity is required. Safe, non-conductive, will not rust or corrode. Integral mounting feet provide easy mounting. Type 2FSE. 32 cubic inch capacity. UL Listed. Four cable knockouts (sides). Two 1/2" and one eccentric TKO conduit knockout (sides). One 1/2" conduit knockout (bottom). 2-1/8" deep. 30.3 cubic inches. With clamps for non-metallic sheathed cable. TS, flush side-mount bracket for wood or metal studs. Fixture support of 6 pounds maximum. Acceptable for use in 2-hour rated fire walls. UL Listed. For dead-end terminations where two devices or additional wiring capacity is required. Integral mounting feet. 32 cubic inch capacity. Type 2FSE UL Listed.
Raco 685 Switch Box Thomas & Betts E381DR Type T Weatherproof Switch Box Raco 2027-FBAR Round Vapor Barrier Box
Drawn construction for surface mount applications. Six 3/4" side knockouts, three 1/2" and two 3/4" bottom knockouts. TS bracket for wood or metal studs. 1/2" bracket setback eliminating the need for a plaster ring. 4" square. Acceptable for use in 2-hour rated walls and ceilings. 2-1/8" deep - 30.3 cubic inches. UL Listed. Weatherproof, for use with nonmetalic wiring systems. Nonconductive, noncorrosive, and impact resistant for a safe, long, service-free life in exposed applications. Install in accordance with NEC and local codes. Three 1/2" threaded ports, one on each end and one in the back. UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, 4" round flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Used independently of vapor barrier hats.
Hubbell 683 Switch Box Raco 2002FBAR Vapor Barrier Box Carlon E981FFN-CTN Type FSC Rigid Switch Box
Drawn construction for surface mount applications. Conduit wiring system. Eight 1/2" and four 3/4" conduit knockouts (sides). Three 1/2" and two 3/4" conduit knockouts (bottom). 4" square. 2-1/8" deep - 30.3 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. Made from rugged polycarbonate material, yellow color, gasket seals all openings to prevent air or vapor penetration. Front-mounted ground screw, 1/2" setback, flush bracket. Self-clamping, nonmetallic sheathed cable entry tabs. Safe, non-conductive, takes standard covers and accessories. For through terminations. With detachable mounting feet. 19 cubic inch capacity.
Raco 888 Raised Square Exposed Work Cover Carlon Adjust-A-Box MB238ADJ Adjustable Switch Box Raco 7120 Ceiling Fan Box
Used to mount switch or receptacle on box in surface mount applications. Raised 1/2". For one 30-60 amp, single receptacle 2.625" diameter. 10.3 cubic inches. UL Listed. Bracket clips on any stud. Securing the bracket to the stud ensures that the box will not move. The box snaps into place on the bracket, square and secure every time. Then turning the screw clockwise or counterclockwise adjusts the box in or out to make it flush with any wall covering. Easily removable to allow inner wall access, or to switch between single gang and double gang boxes. Accommodates high and low voltage applications. Pre-installed ground lug. Flat bottom cable priouts. UL Listed. Round polycarbonate, 4" diameter, 12.5 cubic inch black non-metallic ceiling fan support saddle box, used in new work to mount a ceiling fan or heavy light fixture. Supports a 70  pound fan, or 210 pound fixture. Saddle design straddles standard joist. Hands free installation. 1/2" setback. Two 1/2" knock outs on the side. 4 cable clamps, mounting hardware, instructions, and high strength, hardened screws included. 2-hour fire rating, UL Orange Book. UL Listed.