Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS > NAIL PLATES
Sort By:
1
Ad Tech T3438CK Mixing Nozzle Kit Acorn IHW16100 Insulation Support Wire 16 in L Ultra Bond 1 A9-1 Anchoring Adhesive
Nozzle kit for Ultrabond epoxy 22 oz. system.  Hi-Flow nozzles reduce waste while increasing flow. 15 inch length snaps off to 10 inches if required.  3/8 diameter at tip.  Built in mixing nut allows for fast and easy attachment to cartridge. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Use for anchoring and doweling. Long working time with a quick cure time. Moisture insensitive, can be used in underwater environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications, seismic anchoring and bracing, surface crack repair. Ultra high-strength epoxy mixes through a static mixing tube and can also be resealed which means that any remaining material can be saved for later use. Cartridge w/nozzle.
Miraclebond 1350 A9-MB1350HN Anchoring Adhesive Acorn IHW24100 Insulation Support Wire 24 in L USP Lumber RS20-R Coiled Strap
Two component (1:1 ratio), 100-percent solids, high aspect ceramic blend, solvent-free, non-sag, high strength, high modulus, moisture insensitive epoxy system. Ideal for use as a bonding agent for almost any material, including metal, concrete, brick, wood, stone, block and other substrates. Can also be used for repairing holes, spalls, cracks in concrete, repairing rotted wood, installing and repairing anchor bolts or hand rails. LIMITATIONS: Minimum substrate and ambient temperature 40 degrees F (4.44 degrees C),  Cartridge with two nozzles; medium duty caulking tool required. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
Ultra Bond 1300 A22-1300N Anchoring Adhesive Acorn IHW16500 Insulation Support Wire 16 in L Acorn NSR3418 Round Nail Stake
Two  component (1:1 ratio), 100 percent solids, high modulus, structural epoxy gel. It is a solvent free, low odor high strength, moisture insensitive, non-sag epoxy system. The resin and hardener are uniformly dispensed from a dual cartridge system and mixed simultaneously through a mixing nozzle or available in bulk. Long working time with a full cure in 24 hours. Moisture insensitive, may be used in damp environments, concrete, hollow block, brick, clay and stone. Ideal for vertical, horizontal, and screen applications. Structural bonding of concrete to concrete. Meets ASTM C881-14: Type I, II, IV and V, Grade 3, Class B and C. Cartridges with Nozzle. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc.
USP Lumber ST12 Strap Tie STRAP TIE 3 X 7IN TRIPLE ZINC Vestal CL-2424 Foundation Access Door
Connects wood framing to resist tension forces. G90 galvanizing finish. ST Medium-duty series require 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. 16 Gauge. Medium capacity; requires (20) 10d x 1-1/2" HDG nails for installation. Meets 130 codes. Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA.
Vestal CL-2416 Foundation Access Door Acorn NSR3424 Round Nail Stake Acorn IHW24500 Insulation Support Wire 24 in L
Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
Vestal CL-3216 Foundation Access Door Simpson Strong-Tie LSTA Light Duty Strap Tie Vestal CL-3224 Foundation Access Door
Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA.
STAKE NAIL ROUND 3/4X30IN     USP Lumber LSTA12 Light Capacity Strap Tie Vestal CL-3232 Foundation Access Door
STAKE NAIL ROUND 3/4X30IN
Our Price: $58.45
Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Heavy gauge steel, all welded construction. Built-in lintel attached. Positive latch made to accept padlock. Door size is stenciled on each door. Primed with black corrosion resistant paint. Made in USA.
USP Lumber N16 Joist Bridging STAKE NAIL ROUND 3/4X36IN     Ad Tech TM22HD Dispensing Tool
STAKE NAIL ROUND 3/4X36IN
Our Price: $70.48
Spans 2 joists per unit, typically used for bridging or bracing I-joists. Must be installed before subfloor sheathing to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information including I-joist installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Features an in-line rod system, combined with a specifically designed friction plate that results in exceptional force making dispensing faster and reducing worker exertion and fatigue. Double gripping plates and steel trigger for increased durability and performance. For 22 Oz. cartridges, but comes with adaptable parts which allow for 16 Oz. cartridges as well.
STRAP TIE 3-1/4X16IN TRI-ZINC USP Lumber LSTA18 Light Capacity Strap Tie USP Lumber MSTA18-TZ Medium Capacity Strap Tie
Wide strapping; requires (16) WS15-HDG nails for installation. Meets 110 codes. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes.
USP Lumber PL4 Protection Plate USP Lumber KNS1 Protection Plate USP Lumber T6-TZ T-Post Strap
Easy-to-install for protecting plumbing and power or communication wiring from screw or nail penetration. Conforms to National Electric Code. 16 Gauge - 1/16" Thickness. Easy to install for protecting plumbing and power or communication wiring from screw or nail penetration. 16 gauge, 1/16" thick. Conforms to National Electric Code. Medium-duty straps connect beams to posts. Requires either (3) 1/2" bolts or (12) 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation.
USP Lumber T6 T-Post Strap USP Lumber L6TZ L-Post Strap USP Lumber LSTA24 Light Capacity Strap Tie
Medium-duty straps connect beams to posts. Requires either (3) 1/2" bolts or (12) 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation. Medium-duty straps connect beams to posts. Requires either 1/2" bolts or 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RS150 Coiled Strap USP Lumber MSTA24-TZ Medium Capacity Strap Tie USP Lumber LTW12 Light Capacity Twist Strap
Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. Use to tie framing members to resist tension forces as in stud plate-rim joist and truss-to-top-plate installations. Flat transition bend, for easy installation, splits total length into 2 separate, equal lengths (L1 & L2). G90 galvanizing finish. Requires an equal number of 10d or 10d x 1-1/2 fasteners at each end. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber WBT Flat Wall Brace USP Lumber TSX24 Truss Spacer USP Lumber T12 T-Post Strap
For use on stud walls to resist racking during framing. Can be used to replace code prescribed 1 x 4 wood let-in bracing as a framing aid. Rolled edges and t-style design give strength, rigidity, and eliminate sharp, sheared edges. Framing aid only; Not a substitute for structural shearwall components. G90 galvanizing finish. Requires two 8d nails for each plate, one 8d nail for each stud. 511-pound max for No.WBT12. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. Max load is the max load vector applied at top of stud wall section, not to exceed 25'L, resisted by the combination of wall brace straps installed. Load based on lumber with a 0.50 specific gravity and 19% or less moisture content. 22 Gauge. Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on TSX  for bracing. Requires one 8d nail per end. 10'L overall; 24" O.C. spacing. 22 Gauge - 5 Sections/Piece. Medium-duty straps connect beams to posts. Requires either (3) 1/2" bolts or (12) 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation.
USP Lumber MBG1016 Grip Tooth Joist Bridging USP Lumber MSTA36-TZ Medium Capacity Strap Tie USP Lumber TS Truss Spacer
Special teeth grip joists for easy single-nail installation. Can be installed before or after subfloor is in place (sheathing) to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires one 8d x 1-1/2 nail. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog D10 Reference Pages. 22 Gauge - 2 x 10 Joist Size. Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on the TS for bracing. Requires (1) 8d nail per end to fasten units to trusses, rafters or floor joists. 2'L overall; 24" O.C. spacing. 20 Gauge - 1 Section/Piece.
USP Lumber MTW18 Medium Capacity Twist Strap USP Lumber ICPL58-TZ Protection Plate USP Lumber O16 Joist Bridging
Use to tie framing members to resist tension forces as in stud plate-rim joist and truss-to-top-plate installations. Flat transition bend, for easy installation, splits total length into 2 separate, equal lengths (L1 & L2). G90 galvanizing finish. Requires an equal number of 10d or 10d x 1-1/2 fasteners at each end. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Easy-to-install plates protect plumbing and power/communication wiring from nail or screw penetration. 16 Gauge - 1/16" Thickness. Spans three joists in under/over installation; prong teeth in the center helps reduce nailing. G90 galvanizing finish; bridging should be installed on floor joists with a nominal depth-to-thickness ratio of 5 to 6 or more (2055 National Design Specification for Wood Construction; Section 4.4.1). Install prior to subfloor sheathing; use (2) 8d x 1-1/2" nails at each end. Fully seat nails to avoid any movement against the bridging and subsequent floor noise. 18 Gauge.
USP Lumber ICPL516-TZ Protection Plate USP Lumber MB16 Snap-On Joist Bridging
Easy-to-install plates protect plumbing and power/communication wiring from nail or screw penetration. 16 Gauge - 1/16" Thickness. No-nail bridging. Place in existing floor system where joist movement is suspected to reduce movement and subsequent floor noise. 2 piece construction creates a solid diagonal brace against joist movement. G90 galvanizing finish. Shipped as 1 piece that easily breaks into 2 pieces at center for proper installation. Meets ICC-ES ESR-1781, FL3285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge - 2 x 8-10-12 Joist Size.
   
 
1