Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS > MENDING PLATES
Sort By:
1
Stanley 316489 Weldable Rebar Stanley 346965 Weldable Rebar Stanley 316497 Weldable Rebar
Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 36 in Overall Length, Steel Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 4 ft Overall Length, Steel, Used in Landscaping Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 72 in Overall Length, Steel, Used in Landscaping
LL Buildsite DA1212W Square Dual Louver LL Buildsite DA1212 Square Dual Louver Acco 103 Cork Roll
One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. Used for custom bulletin boards and wall borders. Natural color. 1/8" Thickness.
LL Buildsite DA1218 Rectangle Dual Louver LL Buildsite DA1218W Rectangle Dual Louver Acorn IHW16100 Insulation Support Wire 16 in L
One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
LL Buildsite DA1424 Dual Louver LL Buildsite DA1424W Dual Louver Marshall JP16 Adjustable Extend-O-Post Jackpost
One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension.
LL Buildsite DA1824 Dual Louver Acorn IHW24100 Insulation Support Wire 24 in L LL Buildsite DA1824W Dual Louver
One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting.
Duraflo 626043-00 Square Gable Vent Acorn IHW16500 Insulation Support Wire 16 in L Duraflo 626060-00 Octagon Gable Vent
Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene for impact. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 44 sq. ins. of net free area. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 58 sq. ins. of net free area. Includes a 3" snap on  trim ring for easy installation.
Duraflo 626055-00 Round Gable Vent Marshall JP36 Adjustable Extend-O-Post Jackpost LL Buildsite DA2430 Dual Louver
Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 55 sq. ins. of net free area. Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting.
Duraflo 626080-00 Small Rectangular Gable Vent Duraflo 626075-00 Small Rectangular Gable Vent LL Buildsite DA2430W Dual Louver
Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene for impact. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 44 sq. ins. of net free area for 12" x 18" and 18" x 24". 74 sq. ins. of net free area for 22" x 28". Rough cut opening is 12.5" x 18.25". Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene for impact. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 44 sq. ins. of net free area for 12" x 18" and 18" x 24". 74 sq. ins. of net free area for 22" x 28". Rough cut opening is 12.5" x 18.25". One piece aluminum central louver panel construction with pre-punched louvered vanes. Designed for flush or recessed mounting.
Marshall JP55 Adjustable Extend-O-Post Jackpost Acorn NSR3418 Round Nail Stake Lomanco 900 Triangular Line Single Vari-Pitch Louver
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting.
GAF Master Flow SGM20 Shutter Power Gable Ventilator Acorn NSR3424 Round Nail Stake Acorn IHW24500 Insulation Support Wire 24 in L
Use with all attic power gable mount vents; moving air opens the louvers only when the power vent is operating; when vent is off, shutter helps prevent infiltration of rain , snow, insects, etc.; maintenance-free white aluminum construction; can be painted if desired. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
Marshall JP79 Adjustable Extend-O-Post Jackpost USP Lumber NP Truss Mending Plate Duraflo 626120-00 Large Rectangular Gable Vent
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge. Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene for impact. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 44 sq. ins. of net free area for 12" x 18" and 18" x 24". 74 sq. ins. of net free area for 22" x 28". Rough cut opening is 12.5" x 18.25".
Marshall JP84 Adjustable Extend-O-Post Jackpost Duraflo 626110-00 Cathedral Gable Vent Lomanco 900 Triangular Line Single Vari-Pitch Louver
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 90 sq. ins. of net free area. Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting.
STAKE NAIL ROUND 3/4X30IN     LL Buildsite PVM105/110 Replacement Motor CMC PIN04N018 Non-Graded Rebar Pin
STAKE NAIL ROUND 3/4X30IN
Our Price: $58.45
Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Replacement motor for GM30, PG1, PG2, MD105, MD105D, H122D, PR1, PR1D, PR2D, PR2DHT, EGV5, ERV4 & ERV5 series power vents. Reinforced bar, commonly used in concrete and masonry structures.
Duraflo 626095-00 Half Moon Gable Vent STAKE NAIL ROUND 3/4X36IN     Marshall JP84HD Adjustable Extend-O-Post Jackpost
STAKE NAIL ROUND 3/4X36IN
Our Price: $70.48
Drip channel drains water to the front of the siding to eliminate wood rot. Wide trim ring, removable template, large flange, and level lines. Injection-molded UV resistant polypropylene for impact. Molded in screen prevents insects and bees from nesting in gable vent. Molded in screen cannot become unglued. Deep wood grain finish enhances appearance for a real wood look. Weeping holes prevent condensation or moisture from remaining trapped. Suitable for use with vinyl or aluminum siding, shake, stucco or brick. 111 sq. ins. of net free area. Used for securing wood and metal forms to the ground in all flatwork applications, for attaching screed bard holder clamps, for securing landscape timbers, surveying stakes, string line guides, etc. Use for supporting sagging floors, weak beams and warping stairways. 2-1/2" x 14 gauge prime steel inner tubing. 2-3/4" x 14 gauge prime steel outer tubing. 2-1/2" steel collar. 1-1/4" x 6" steel screw. Two 4" x 6" x 7 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension.
Lomanco 900 Triangular Line Single Vari-Pitch Louver USP Lumber NP35 Truss Mending Plate Marshall AC363/3637 Adjustable Round Column
Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
USP Lumber TPP24 Prong Mending Plate Marshall AC369/3691 Adjustable Round Column Marshall AC386 Adjustable Round Column
Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly; no load ratings assigned. G90 galvanizing finish. 22 Gauge. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
Marshall AC370/3704 Adjustable Round Column Lomanco 100 Flush Mount Rectangular Gable Vent Marshall AC373/3737 Adjustable Round Column
3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. All-aluminum construction. Used for flush mounting. 8" x 8" perma-coated screen attached for insect protection. Machine tab-folded construction. Wide mounting flange. Built-in weather protection. Provides 36 square inches of net free ventilating area. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
CMC PIN03NO18 Graded Rebar Pin Marshall AC390 Adjustable Round Column Marshall AC376/3760 Adjustable Round Column
Reinforced bar, commonly used in concrete and masonry structures. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
CMC PIN04N024 Non-Graded Rebar Pin Marshall AC379/3791 Adjustable Round Column USP Lumber TPP Truss Mending Plate
Reinforced bar, commonly used in concrete and masonry structures. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly; no load ratings assigned. G90 galvanizing finish. 22 Gauge.
Marshall AC380/3804 Adjustable Round Column Lomanco 900 Triangular Line Single Vari-Pitch Louver Marshall AC383/3837 Adjustable Round Column
3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
FAN GABLE MOUNT ATTIC 1450 CFM Add-A-Vent 1800 Gable Ventilator USP Lumber FB24-TZ Fence Bracket
Energy efficient PSC (permanent-split capacitor) helps to reduce energy costs and helps prolong life of the roof and shingles; rust-resistant metal for durability; mounts in the gable inside the attic; adjustable thermostat included; mounting brackets included for installation and optional humidistat available (H1) - sold separately. All aluminum construction. Balanced blades pitched for smooth operation and high volume air removal. Five blades with 12" diameter. Factory-set adjustable thermostat (switches on at 100 degrees and off at 85 degrees). Thermostat features a "push to test" button. Can be mounted in horizontal or vertical positions on either 16" or 24" center framing members. Designed to mount behind existing gable louver. Motor: 1/10 HP; 1100 RPM; 3.4 Amps; 120 Volts. Provides stronger fence connections and simplifies fence assembly. Can be installed before posts are set to help ensure uniform spacing and alignment. Requires five 6d HDG fasteners for rails and three 8d HDG fasteners for posts.
Lomanco 900 Triangular Line Single Vari-Pitch Louver CMC PIN03N024 Rebar Pin USP Lumber NP37 Truss Mending Plate
Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting. Reinforced bar, commonly used in concrete and masonry structures. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge.
FAN GABLE MOUNT ATTIC 1600 CFM USP Lumber N16 Joist Bridging Lomanco 900 Triangular Line Single Vari-Pitch Louver
Energy efficient PSC (permanent-split capacitor) helps to reduce energy costs and helps prolong life of the roof and shingles; rust-resistant metal for durability; mounts in the gable inside the attic; adjustable thermostat included; mounting brackets included for installation and optional humidistat available (H1) - sold separately. Spans 2 joists per unit, typically used for bridging or bracing I-joists. Must be installed before subfloor sheathing to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information including I-joist installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge. Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting.
LATE MNDG 13/16X3-1/2IN       USP Lumber MBG1016 Grip Tooth Joist Bridging Lomanco 900 Triangular Line Single Vari-Pitch Louver
Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly; no load ratings assigned. G90 galvanizing finish. 22 Gauge. Special teeth grip joists for easy single-nail installation. Can be installed before or after subfloor is in place (sheathing) to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires one 8d x 1-1/2 nail. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog D10 Reference Pages. 22 Gauge - 2 x 10 Joist Size. Rust-free, vari-pitch louver. Adjustable roof pitch. 8" x 8" perma-coated screen. Wide mounting flange. Pivoting blades provide maximum weather protection. Net free area varies based on pitch setting.
USP Lumber TS Truss Spacer Mutual 14640-4 Rebar Cap USP Lumber TSX24 Truss Spacer
Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on the TS for bracing. Requires (1) 8d nail per end to fasten units to trusses, rafters or floor joists. 2'L overall; 24" O.C. spacing. 20 Gauge - 1 Section/Piece. OSHA rebar caps made of space age high-density polymer to protect against impalement injuries. Bright orange and fits rebar #4 - #8. Meets new OSHA requirement 344.90. Boxed. Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on TSX  for bracing. Requires one 8d nail per end. 10'L overall; 24" O.C. spacing. 22 Gauge - 5 Sections/Piece.
USP Lumber NP39 Truss Mending Plate Mutual 14640-3 Standard Rebar Cap USP Lumber MB16 Snap-On Joist Bridging
Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge. Mushroom style rebar safety caps protect from protruding rebar at construction sites. Bright colors for excellent visibility. Use where the danger of impalement is not present. No-nail bridging. Place in existing floor system where joist movement is suspected to reduce movement and subsequent floor noise. 2 piece construction creates a solid diagonal brace against joist movement. G90 galvanizing finish. Shipped as 1 piece that easily breaks into 2 pieces at center for proper installation. Meets ICC-ES ESR-1781, FL3285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge - 2 x 8-10-12 Joist Size.
USP Lumber O16 Joist Bridging USP Lumber JNP24 Joiner Nail Mending Plate USP Lumber JNP28 Joiner Nail Mending Plate
Spans three joists in under/over installation; prong teeth in the center helps reduce nailing. G90 galvanizing finish; bridging should be installed on floor joists with a nominal depth-to-thickness ratio of 5 to 6 or more (2055 National Design Specification for Wood Construction; Section 4.4.1). Install prior to subfloor sheathing; use (2) 8d x 1-1/2" nails at each end. Fully seat nails to avoid any movement against the bridging and subsequent floor noise. 18 Gauge. Prong plates with angled, hammer-in prongs. Joins flat surfaces of 2 or more wood members. G90 galvanizing finish. Not intended for structural use OR in truss assembly. No load ratings assigned. 18 Gauge. Prong plates with angled, hammer-in prongs. Joins flat surfaces of 2 or more wood members. G90 galvanizing finish. Not intended for structural use OR in truss assembly. No load ratings assigned. 18 Gauge.
Acco 15075Q Cork Roll
For subflooring. May also be used for custom bulletin boards and wall borders. Comes with foam tape and magnets. Natural color. 5/32" Thickness.
   
 
1