Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS
Choose a sub category:
JOIST HANGERS FRAMING ANGLES/ANCHORS MENDING PLATES
NAIL PLATES POST ANCHORS / CAPS FENCE BRACKETS
BRIDGING INSULATION SUPPORTS STRAPS
PLYWOOD CLIPS FOUNDATION ANCHORS BRICK/WALL TIES
MISC CONSTR HARDWARE
Sort By:
1
USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger USP Lumber JDS24 Double Shear Saddle Purlin Hanger USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Designed for quick installation of purlins between rafters, joists or trusses in post and beam structures. One-piece construction assures a consistent flush fit between purlin and joist or rafter. A reinforced "double lap" seat boosts the load capacity of this heavy-duty purlin hanger. Requires (4) 10d x 1-1/2" nails for header and (4) 10d" nails for each purlin. Features a 1-9/16" top fold; pending IAPMO-ES evaluation. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger Stanley 316489 Weldable Rebar Quik-Tube 6922-01 Building Form
Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 36 in Overall Length, Steel Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed.
Stanley 346965 Weldable Rebar TAPE SEAM BUILDER 3INX180FT   Quikrete 6922-02 Concrete Quik-Tube Form
Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 4 ft Overall Length, Steel, Used in Landscaping Has an aggressive, high tack adhesive that can seam Builder Board together for months; strong, flexible and lays flat. Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed.
RH Tamlyn PC1532 Plywood Clip Stanley 316497 Weldable Rebar RH Tamlyn PCS716 Plywood Clip
With built-in spacer for use when support spacing exceeds the maximum length of an unsupported edge. Boxed. Stanley Weldable Rebar, 1/2 in, NO 4 Nominal, 72 in Overall Length, Steel, Used in Landscaping Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.
RH Tamlyn PCS12 Plywood Clip RH Tamlyn PCS1532 Plywood Clip Quik-Tube 6922-03 Building Form
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed.
USP Lumber SKH28R-TZ Skewed Left Joist Hanger USP Lumber SKH28L-TZ Skewed Left Joist Hanger Trimaco 35140 Economy Builder Paper
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Use as a paint dropcloth and runner, floor protection, garden weed control, for arts and crafts projects, or wrapping paper. Brown.
Squeek No More 1011345 Screw Set RH Tamlyn PCS58 Plywood Clip Trimaco 35145/64 Regular Weight Rosin Paper
Specially scored waxed screws. Scored head breaks off at the same place every time. Carded. Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed. Used as a temporary and disposable general purpose work-over paper to protect surfaces from foot traffic, wall and ceiling texture overspray and paint drippings. Also used in many residential and commercial construction applications as separation sheets between other building products. Sized to resist bleeding and offer moisture protection. 501 square feet per roll. Red.
Trimaco L3536144 Rosin Paper Acorn IHW16100 Insulation Support Wire 16 in L Trimaco 36144 Construction Paper
Use as a paint dropcloth and runner, floor protection, garden weed control, for arts and crafts projects, or wrapping paper. 432 square feet per roll. Brown. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Laminated with high tech fiber coating. Protects floors from paint, equipment, construction materials, and foot traffic. Ideal for protecting carpets, ceramic tile, hardwood, concrete, brick, and vinyl. Has superior moisture hold out and avoids tears. Shields and cushions surfaces. Over 50 percent heavier than regular rosin paper. Use brown on the top and white on the bottom. Brown.
FORM CONCRETE FOOT PLASTC 22IN USP Lumber NA11-5MC Joist Hanger Nail USP Lumber NA9-5MC Joist Hanger Nail
Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed. Structurally rated. For use with MiTek/USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Structurally rated. For use with MiTek/USP Lumber Connectors' products. For additional information including withdrawal load and allowable shear per nail, please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
Squeek No More 1010543 Floor Squeak Repair Kit Marshall JP16 Adjustable Extend-O-Post Jackpost FORM CONCRETE FOOT PLASTC 28IN
Eliminate squeaks quickly and permanently. Can be applied to 2nd floors, hardwood floors, carpet, and stairs. Each kit contains: 1 - alignment and depth control fixture, 50 - specially scored waxed screws, 1 - special driver bit, 1 - complete instruction kit. Carded. Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed.
Acorn IHW24100 Insulation Support Wire 24 in L Deckmate 90166 Deck Bench Bracket with Bench Bracket USP Lumber RS20-R Coiled Strap
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. You determine the size. Connect with railing brackets with 2x4 and 2x6 lumber to easily add a bench to any size or shape deck. Gain increased seating area while using only 7" of deck space. Assembled unit stands 36"H for deck railing, seat is 17"H. Quick and easy to assemble using basic tools. Includes bench bracket, hardware and instructions. LUMBER NOT INCLUDED. Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
ANGLE 2X4IN TRIPLE ZINC 12GA  Acorn IHW16500 Insulation Support Wire 16 in L Marshall JP36 Adjustable Extend-O-Post Jackpost
Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension.
USP Lumber PA66R Post Anchor RH Tamlyn BT 22SP Corrugated Straight Brick Wall Tie RH Tamlyn BT22ZZSP Corrugated Scalloped Zig Zag Brick Wall Tie
Used to secure wood posts to concrete footings and to provide moisture damage protection. 4-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8".
Marshall JP55 Adjustable Extend-O-Post Jackpost RH Tamlyn BT28ZZ5SP Corrugated Scalloped Zig Zag Brick Wall Tie RH Tamlyn BT28500SP Corrugated Straight Brick Wall Tie
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Masonry accessory used to tie a brick veneer to the exterior of the house. 2 holes provide for nailing on one end; other end is bent to lie between the mortar joints. Follow local codes for spacing. 6-3/8" x 7/8". Boxed.
ANGLE 2X6IN TRIPLE ZINC 12GA  USP Lumber JL24 Standard Joist Hanger Deckmaster DMP125-10 Hidden Deck Bracket Kit
Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. System eliminates the damage to deck boards by hiding all fasteners beneath deckboards. Holds boards tight to eliminate any surface penetration. No moisture can enter deckboards or joists and cause nail penetration. No moisture can enter deckboards or joists and cause nail or screw pop-ups or deck rot. No stains or splinters form around fastener holes. Corrosion resistance. Powder coating's natural wood color blends with the understructure of balconies. For: 3/4" thick boards, composites less than 1-1/8", and any hollowcore composites. Consumer pack includes: 10 brackets, (120) 10 x 1" deck board screws, (110) 8 x 1" joist screws, and a pro bit tip.
USP Lumber MP34 Framing Angle Simpson Strong-Tie LSTA Light Duty Strap Tie USP Lumber RT7A Double Plate Hurricane/Seismic Anchor
Use for joist/header installations. Does not have tabs. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505; ICBO 5736; DSA PA-076; Dade County, FL 01-0417.11; and  L.A. City RR25303 codes. 18 Gauge. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JL26 Standard Joist Hanger National Nail 1/2X6 Pre-Formed Anchor Bolt FORM CONCRETE FOOT PLASTC 32IN
G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed.
National Nail 3/8X8 Pre-Formed Anchor Bolt Acorn IHW24500 Insulation Support Wire 24 in L USP Lumber RT3A Double Plate Hurricane/Seismic Anchor
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge. Ties trusses and rafters to top plates either left or right handed. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. G90 galvanizing finish. Requires 8d nails for installation in plate and rafter/truss. Meets ICC-ES ESR-1465 and FL817 codes. 18 Gauge.
Marshall JP79 Adjustable Extend-O-Post Jackpost USP Lumber LSTA12 Light Capacity Strap Tie USP Lumber NP Truss Mending Plate
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge.
Marshall JP84 Adjustable Extend-O-Post Jackpost USP Lumber JUS28 Double Shear Slant Joist Hanger Surface Protection BLDLS38100 Builder Board
Use for supporting sagging floors, weak beams and warping stairways. 2-1/4" x 15 gauge prime steel inner tubing. 2-1/2" x 15 gauge prime steel outer tubing. 2-1/4" steel collar. 1" x 6" steel screw. Two 4" x 4" x 10 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Temporary floor protection now repels water, mud, paint, and more. It protects floors from tracked in water and job site spills while allowing moisture and vapors to escape for curing. One roll covers the same area as 10 sheets of masonite. Tough enough to be driven on. 100% recyclable.
Hopkins 90110 Comfortable Flip Top Bench Table FLOOR PROTECTOR 38INX100FT HD USP Lumber RT Hurricane/Seismic Anchor
Make a comfortable, sturdy bench and a table up to 8' long. Just add 2x4 lumber pieces. Flips and locks from a bench to a table in seconds without using tools. Slide lock safely secures and locks in position. Made of maintenance free structural resin. Use only one or slide two Bench Tables together for a full size picnic table. Good for small porches and decks. Assembled unit stands 34"H in the bench position, 31"H in the table position and both with 17.5"H seat. Includes Bench Table legs, hardware and instructions. LUMBER NOT INCLUDED. A contractor strength floor protection roll for your toughest jobs; made from 100 percent recycled newsprint; eco-friendly; breathable to protect new and existing wood, concrete, stone, tile, linoleum, epoxy, vinyl composition tile and most other floor types; new innovative liquid repellent technology protects against paint, mud, water and more; earns up to 2 LEED points on projects seeking USGBC certification; safe for all surfaces; forklift strong; made in the USA. Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber PCP Post Cap National Nail 1/2X8 Pre-Formed Anchor Bolt CMC PIN04N018 Non-Graded Rebar Pin
Seamless, keeps water off post tops to protect wood from moisture damage. Corrosion-proof and paintable. Requires one 8d HDG or 10d HDG nail for installation. 3-5/8"W - For 4 x 4 Post/Column. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Reinforced bar, commonly used in concrete and masonry structures.
National Nail AG5810 Pre-Formed Anchor Bolt National Nail AG5808 Pre-Formed Anchor Bolt USP Lumber JL28 Standard Joist Hanger
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT8A Double Plate Hurricane/Seismic Anchor USP Lumber ST1-TZ Mud Sill Anchor USP Lumber JA1 Joist Angle
Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For securing mudsills and framing into concrete slabs or poured stemwalls. Not for block installation or securing concrete sections together between cold joints. Features prebent base flange for proper anchoring into concrete. Use a minimum of 2 anchors per mudsill within 12" of the end of each section. Meets  NER 530 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Used to strengthen framing in various applications or to support joists where stirrup style hangers cannot be installed. Requires 10d x 1-1/2 nails for installation. Meets ICBO, SBCCI, BOCA - NER 505; L.A. City RR25303, DSA PA-076; and Dade County, FL 98-0421.06 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 16 Gauge.
USP Lumber JA1-TZ Framing Angle U-CLIP 2X-2X TRIPLE ZINC      USP Lumber KHL33 Heavy Joist Angle
Used to strengthen framing in various applications or to support joists where stirrup style hangers cannot be installed. Requires 10d x 1-1/2 nails for installation. Meets ICBO, SBCCI, BOCA - NER 505; L.A. City RR25303, DSA PA-076; and Dade County, FL 98-0421.06 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 16 Gauge. A clip connects a 2x wood member to the face of another wood member; 20 gauge; G-185 galvanizing finish; requires (6) USP LumberLok LL915 (#9 x 1-3/8" long) wood screws not included. Designed for heavy-duty reinforcement of 90 degree framing intersections. USP primer finish. Requires (2) 5/8" bolts for installation. Meets ICBO 2725, L.A. City RR 25104. 7 Gauge.
USP Lumber PL4 Protection Plate National Nail AG06 Pre-Formed Anchor Bolt National Nail AG08 Pre-Formed Anchor Bolt
Easy-to-install for protecting plumbing and power or communication wiring from screw or nail penetration. Conforms to National Electric Code. 16 Gauge - 1/16" Thickness. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Marshall JP84HD Adjustable Extend-O-Post Jackpost USP Lumber JUS28-TZ Double Shear Slant Joint Hanger National Nail 1/2X10 Pre-Formed Anchor Bolt
Use for supporting sagging floors, weak beams and warping stairways. 2-1/2" x 14 gauge prime steel inner tubing. 2-3/4" x 14 gauge prime steel outer tubing. 2-1/2" steel collar. 1-1/4" x 6" steel screw. Two 4" x 6" x 7 gauge steel plates. 7" turning handle. Grooved pin and plain pin. Flow coated with red corrosion-resistant paint. Packed with instructions. UPC symbol on carton. Maximum load capacity obtained at lowest extension. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
USP Lumber CPB Composite Post Base National Nail AG5812 Pre-Formed Anchor Bolt Hopkins 90158 Workbench Kit
Provides a raised base that elevates wood posts above concrete surfaces to avoid moisture from ground contact. Single-piece design made from composite material; will not corrode. Open center enables installation of metal rod from concrete into post. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning moment loads. Requires (4) 10d HDG nails. ACQ approved. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Create a workbench, worktable or power tool stand. Add 2x4's plywood or particleboard to make a workbench, worktable or power tool stand in any length or width up to 8'L x 4'W. Simple assembly in less than an hour with only powered screwdriver and a saw. Only straight, 90-degree cuts required, no miter or angles. Made of structural resin.  Kit includes: 4 legs, hardware and instructions. LUMBER AND SHELF LINKS NOT INCLUDED.
National Nail AG10 Pre-Formed Anchor Bolt USP Lumber NP35 Truss Mending Plate USP Lumber JUS210 Double Shear Slant Joist Hanger
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber LSTA18 Light Capacity Strap Tie National Nail 1/2X12 Pre-Formed Anchor Bolt Marshall AC363/3637 Adjustable Round Column
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
USP Lumber BL Corner Brace National Nail AG12 Pre-Formed Anchor Bolt USP Lumber TPP24 Prong Mending Plate
Reinforces 90 degree wood-to-wood connections. G90 galvanizing finish. Requires 16d nails for installation. 12 Gauge. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly; no load ratings assigned. G90 galvanizing finish. 22 Gauge.
USP Lumber JL210 Standard Joist Hanger Marshall AC369/3691 Adjustable Round Column STRAP TIE 3-1/4X16IN TRI-ZINC
G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. Wide strapping; requires (16) WS15-HDG nails for installation. Meets 110 codes.
STRAP TIE 3 X 7IN TRIPLE ZINC HANGER RIDGE RAFTER 18 GAUGE  Marshall AC386 Adjustable Round Column
Medium capacity; requires (20) 10d x 1-1/2" HDG nails for installation. Meets 130 codes. Supports rafter pitches up to 7:12 (30?). Nesting top flange for installation on 2x support beams. Use all specified fasteners. The rafter end at the ridge must be plumb cut to achieve published loads. Optional diamond nail holes can be used to faster RR to end of rafter before settling rafter into place. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
Marshall AC370/3704 Adjustable Round Column Marshall AC373/3737 Adjustable Round Column CMC PIN03NO18 Graded Rebar Pin
3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. Reinforced bar, commonly used in concrete and masonry structures.
USP Lumber JUS24 Double Shear Slant Joist Hanger Marshall AC390 Adjustable Round Column Marshall AC376/3760 Adjustable Round Column
Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
USP Lumber KNS1 Protection Plate CMC PIN04N024 Non-Graded Rebar Pin Marshall AC379/3791 Adjustable Round Column
Easy to install for protecting plumbing and power or communication wiring from screw or nail penetration. 16 gauge, 1/16" thick. Conforms to National Electric Code. Reinforced bar, commonly used in concrete and masonry structures. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145.
USP Lumber T6 T-Post Strap USP Lumber ST12 Strap Tie USP Lumber TPP Truss Mending Plate
Medium-duty straps connect beams to posts. Requires either (3) 1/2" bolts or (12) 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation. Connects wood framing to resist tension forces. G90 galvanizing finish. ST Medium-duty series require 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. 16 Gauge. Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly; no load ratings assigned. G90 galvanizing finish. 22 Gauge.
Marshall AC380/3804 Adjustable Round Column Marshall AC383/3837 Adjustable Round Column USP Lumber JUS24-TZ Double Shear Slant Joint Hanger
3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. 3"OD 11 gauge (0.120 wall). 4" adjustment. Cold rolled steel screw. Turning bar provided with each post. Flow-coated inside and out with red corrosion-resistant paint. Heavy-duty cap and base plates slotted; holes to fit steel or wood beams. Embossed lugs grip posts firmly to avoid slipping. All parts are welded or wired together. Meets IRC and IBC Specifications Report No. CCRR-0145. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT15 Double Plate Hurricane/Seismic Anchor USP Lumber PB66-6TZ 1-Piece Post Cap 18 ga T USP Lumber PB 2-Piece Split Post Cap
Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc finish requires 8d HDGnails for installation in plate and rafter/truss and Gold Coat anchor requires N8-GC nails. 1-9/16"W x 2-5/8"H opening. Meets ICC-ES ESR-1465, FL817 and Dade County, FL 07-0306.10 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Contractors charts in the Orgill paper catalog R7 for reference pages. 18 GAUGE - 5-1/4"H. For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. Use two caps for each installation project to act as a unit. Designed to work with single, solid sawn beams, but can be used with build-up beams made of 2x lumber and shims fastened. "-TZ" following item number indicates Triple Zinc finish. "-GC" following item number indicates Gold Coat finish. Meets ICC-ES ESR-1781, FL18285 and L.A. City RR25843 codes. For additional information including allowable loads loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. Use two caps for each installation project to act as a unit. Designed to work with single, solid sawn beams, but can be used with build-up beams made of 2x lumber and shims fastened. "-TZ" following item number indicates Triple Zinc finish. "-GC" following item number indicates Gold Coat finish. Meets ICC-ES ESR-1781, FL18285 and L.A. City RR25843 codes. For additional information including allowable loads loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber MPA1 Framing Angle ANGLE 2X-2X TRIPLE ZINC 16GA  USP Lumber RS150 Coiled Strap
Use for joist to header, rafter to plate, stud to plate or 1" foamboard installations. Achieves continuous load path in high wind and seismic resistant construction. Enables quick field adjustments for 2 and 3-way connections. Tabs enable two and three-way connections. Bend tabs only once. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505, ICBO 5736, DSA PA-076, Dade County, FL 01-417.11 and  L.A. City RR25303 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. An angle connects two 2x wood members at 90? angles; G185 galvanizing finish; requires (8) USP LumberLok LL915 (#9 x 1-3/8" long) wood screws not included. Enables cut-to-length convenience for job site needs. G90 galvanizing finish. 1-1/2" nail spacing. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS26 Double Shear Slant Joist Hanger USP Lumber FB24-TZ Fence Bracket USP Lumber JUS26-TZ Double Shear Slant Joint Hanger
Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Provides stronger fence connections and simplifies fence assembly. Can be installed before posts are set to help ensure uniform spacing and alignment. Requires five 6d HDG fasteners for rails and three 8d HDG fasteners for posts. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT Hurricane/Seismic Anchor USP Lumber LSTA24 Light Capacity Strap Tie USP Lumber MPA1 Framing Angle
Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc finish requires 8d HDGnails for installation in plate and rafter/truss and Gold Coat anchor requires N8-GC nails. 1-9/16"W x 2-5/8"H opening. Meets ICC-ES ESR-1465, FL817 and Dade County, FL 07-0306.10 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Contractors charts in the Orgill paper catalog R7 for reference pages. 18 GAUGE - 5-1/4"H. Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Use for joist to header, rafter to plate, stud to plate or 1" foamboard installations. Achieves continuous load path in high wind and seismic resistant construction. Enables quick field adjustments for 2 and 3-way connections. Tabs enable two and three-way connections. Bend tabs only once. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505, ICBO 5736, DSA PA-076, Dade County, FL 01-417.11 and  L.A. City RR25303 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS210-TZ Double Shear Slant Joint Hanger USP Lumber JUS26-2 Double Shear Slant Support Joist Hanger USP Lumber SFP30 Fence Post Connector
Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Install wooden posts permanently or temporarily without digging.  For heavy-duty applications such as long runs of fencing, corner and gate posts, larger wooden gym sets, detached patio decking, wooden sidewalks, seasonal docks, and more. Removable Forcefit clamps and 2-piece construction, increases unit strength and eliminates welds which are potential weak spots. Reverse spike blades offer lateral soil resistance, increased stability, and allows driving without rotating for easy post alignment. Welded steel construction with high tech baked-on finish, rust resistant and 100% environmentally safe. Application information and installation instructions labeled on each. Green Commission finish. 13 Gauge - For 4 x 4 Posts.
CMC PIN03N024 Rebar Pin USP Lumber NP37 Truss Mending Plate USP Lumber T6-TZ T-Post Strap
Reinforced bar, commonly used in concrete and masonry structures. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge. Medium-duty straps connect beams to posts. Requires either (3) 1/2" bolts or (12) 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation.
USP Lumber CPB Composite Post Base USP Lumber N16 Joist Bridging USP Lumber TFL2595 Joist Hanger
Provides a raised base that elevates wood posts above concrete surfaces to avoid moisture from ground contact. Single-piece design made from composite material; will not corrode. Open center enables installation of metal rod from concrete into post. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning moment loads. Requires (4) 10d HDG nails. ACQ approved. Spans 2 joists per unit, typically used for bridging or bracing I-joists. Must be installed before subfloor sheathing to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information including I-joist installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge. Features 1-1/2" top flange depth that accommodates all header types as well as back-to-back installations. Features "Seat Cleat" for quick, positive seating. G90 galvanizing finish. Meets ICC-ES ESR-1831 codes. Header requires (6) 10d nails and joist requires (2) 10d x 1-1/2 nails for installation. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge.
USP Lumber BL Reinforcement Corner Brace USP Lumber WBT Flat Wall Brace USP Lumber L6TZ L-Post Strap
Reinforces 90 degree wood-to-wood connections. G90 galvanizing finish. Requires 16d nails for installation. 12 Gauge. For use on stud walls to resist racking during framing. Can be used to replace code prescribed 1 x 4 wood let-in bracing as a framing aid. Rolled edges and t-style design give strength, rigidity, and eliminate sharp, sheared edges. Framing aid only; Not a substitute for structural shearwall components. G90 galvanizing finish. Requires two 8d nails for each plate, one 8d nail for each stud. 511-pound max for No.WBT12. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes. Max load is the max load vector applied at top of stud wall section, not to exceed 25'L, resisted by the combination of wall brace straps installed. Load based on lumber with a 0.50 specific gravity and 19% or less moisture content. 22 Gauge. Medium-duty straps connect beams to posts. Requires either 1/2" bolts or 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation.
USP Lumber ST2-TZ Mud Sill Anchor USP Lumber EPB Elevated Post Base LATE MNDG 13/16X3-1/2IN
For securing mudsills and framing into concrete slabs, poured stemwalls, or concrete block. Not for securing concrete sections together between cold joints. Features prebent base flange for proper anchoring into concrete. Use a minimum of 2 anchors per mudsill within 12" of the end of each section. Meets NER 530 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Allows installer to pre-align posts and to preset post height above concrete floors or footings. Eliminates post-to-concrete contact for reduced moisture damage. Nails fasten to posts for carports, decks or porches. EPB is welded and primed. EBG is galvanized for added corrosion resistance. Not recommended for fence posts or unrestrained (not fixed or fastened at top) applications.. Requires (8) 16d nails for EPB4408, (12) 16d nails for EPB6608, (8) 16d HDG nails for EBG44-TZ . Meets SBCCI, BOCA - NER 505, ICBO 5736, L.A. City RR 25303 and DSA PA-076 codes. For additional information including allowable loads, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly; no load ratings assigned. G90 galvanizing finish. 22 Gauge.
Quikrete 6917-03 Expansion Joint USP Lumber JUS26-2TZ Double Shear Slant Joint Hanger USP Lumber JUS210-2 Double Shear Slant Support Joist Hanger
Used where concrete meets concrete for a stronger bond. Expansion joint filler made from resilient wood to prevent damage during expansion and contraction of concrete. Used in driveways, sidewalks, and patios, between concrete slabs and to separate slabs from structures. Meets requirements of ASTM D 1751. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber MSTA18-TZ Medium Capacity Strap Tie USP Lumber PA(E) 2-Sided Post Anchor USP Lumber TFL20118 Joist Hanger
Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. Used to secure wood posts to concrete footings and to provide moisture damage protection. 2-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR 25836 codes. Features 1-1/2" top flange depth that accommodates all header types as well as bact-to-back installations. Features "Seat Cleat" for quick, positive seating. G90 galvanizing finish. Meets ICC-ES ESR-1831. Header requires (6) 10d nails and joist requires (2) 10d x 1-1/2" nails for installation. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge.
USP Lumber JUS28-2 Double Shear Slant Joist Hanger USP Lumber SCA Stair Angle USP Lumber PA(E) 2-Sided Post Anchor
Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Simplifies stair construction and eliminate the need to calculate and notch stair stringers. Stronger and safer than wood blocking, and the angle and fasteners are hidden from view. Use the SCA9 for single 2x10 stair treads and SCA10 for double 2 x 6 stair treads. Requires 1/4" x 1-1/2" lag bolts. Meets ICC-ES ESR-1280, FL11664 and L.A. City RR25749 codes. For additional information on installation, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Used to secure wood posts to concrete footings and to provide moisture damage protection. 2-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR 25836 codes.
USP Lumber FA3-TZ Foundation Anchor USP Lumber TFL25118 Joist Hanger USP Lumber PA44-TZDP Post Anchor
For securing mudsills and framing into concrete slabs. Do not rely-on for securing concrete sections together between cold joints. Features split flange for nailing to both mudsill and stud for greater framing versatility. Use a minimum of 2 anchors per mudsill within 12" of the end of each section. Meets ICC-ES ESR-2787 codes For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Features 1-1/2" top flange depth that accommodates all header types as well as back-to-back installations. Features "Seat Cleat" for quick, positive seating. G90 galvanizing finish. Meets ICC-ES ESR-1831 codes. Header requires (6) 10d nails and joist requires (2) 10d x 1-1/2 nails for installation. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge. Used to secure wood posts to concrete footings and to provide moisture damage protection. 4-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes.
USP Lumber MBG1016 Grip Tooth Joist Bridging USP Lumber RT10 Double Plate Hurricane/Seismic Anchor USP Lumber CSH-TZ Concealed Stringer Hanger
Special teeth grip joists for easy single-nail installation. Can be installed before or after subfloor is in place (sheathing) to reduce joist movement and subsequent floor noise. G90 galvanizing finish. Requires one 8d x 1-1/2 nail. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog D10 Reference Pages. 22 Gauge - 2 x 10 Joist Size. Used to tie wood framing members to resist uplift and lateral forces. G90 galvanizing finishing. Requires 8d nails for installation. Meets ICC-ES ESR-1465, FL817 and Dade County, FL 07-0306.10 codes. 18 Gauge. Concealed stair stringer hanger provides a method of connecting a stringer with a hidden hanger. The seat of the hanger is adjustable to match the slope of the stair stringer. Triple Zinc finish. Requires (8) 10d x 1-1/2 HDG nails for header and (5) 10d x 1-1/2 HDG nails for joist. 18 Gauge. Pending IAPMO-ES evaluation.
USP Lumber BP583 Standard Bearing Plate USP Lumber LTW12 Light Capacity Twist Strap USP Lumber WE44-TZ Wet Post Anchor
Designed to meet code requirements for mudsill-to-foundation and stud-to-foundation connections. Use to tie framing members to resist tension forces as in stud plate-rim joist and truss-to-top-plate installations. Flat transition bend, for easy installation, splits total length into 2 separate, equal lengths (L1 & L2). G90 galvanizing finish. Requires an equal number of 10d or 10d x 1-1/2 fasteners at each end. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Secures posts to concrete in light-duty and medium-duty applications such as patio covers, carports or decks. Formed, one-piece design includes embossing for additional lateral strength. Not  for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires (2) 1/2" HDG bolts or (12) HDG nails for fastening to post. Meets SBCCI, BOCA - NER 530 & NER 608, ICBO 5700, ICBO 2039, ICBO 5531, FL821, FL822, L.A. City RR 25337, and DSA PA-076 codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT16A Double Plate Hurricane/Seismic Anchor USP Lumber HBPS12 Slotted Bearing Plate USP Lumber PA46E-TZ Post Anchor
Anchor tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces. Typical Truss/rafter to double plate installation. Requires Meet ICC-ES ESR-1465 and FL817 codes. Offers anchor bolt adjustment slots. Used to secure wood posts to concrete footings and to provide moisture damage protection. 2-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR 25836 codes.
USP Lumber D Post Anchor USP Lumber A3 Framing Angle USP Lumber SDJT14-TZ Deck Post Tie
Secures nominal sized post to wood surfaces offering some lateral and uplift resistance. May be used only for intermediate posts between fully anchored corner/end posts in rail system. Not Recommended for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d HDG fasteners for post and 16d HDG fasteners for base. Meets ICBO 2039 and L.A. City RR23888 codes. For additional information including allowable loads, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Eliminates toenailing and increases strength. Requires 10d x 1-1/2" nails for installation. 1-7/16"W1 X 1-7/16"W2 X 2-3/4"L - 18 GAUGE. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. Secures 2x joist to posts. Requires 16d HDG nails or 5/8" HDG bolts for installation. 14 Gauge.
USP Lumber SCA Stair Angle USP Lumber T12 T-Post Strap USP Lumber MSTA24-TZ Medium Capacity Strap Tie
Simplifies stair construction and eliminate the need to calculate and notch stair stringers. Stronger and safer than wood blocking, and the angle and fasteners are hidden from view. Use the SCA9 for single 2x10 stair treads and SCA10 for double 2 x 6 stair treads. Requires 1/4" x 1-1/2" lag bolts. Meets ICC-ES ESR-1280, FL11664 and L.A. City RR25749 codes. For additional information on installation, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Medium-duty straps connect beams to posts. Requires either (3) 1/2" bolts or (12) 16d nails for installation. Triple Zinc straps require HDG bolts or 16d HDG nails for installation. Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes.
USP Lumber TS Truss Spacer Mutual 14640-4 Rebar Cap USP Lumber JUS26-GC Double Shear Slant Joist Hanger
Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on the TS for bracing. Requires (1) 8d nail per end to fasten units to trusses, rafters or floor joists. 2'L overall; 24" O.C. spacing. 20 Gauge - 1 Section/Piece. OSHA rebar caps made of space age high-density polymer to protect against impalement injuries. Bright orange and fits rebar #4 - #8. Meets new OSHA requirement 344.90. Boxed. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber C66-TZ 1-Piece Post Beam Cap USP Lumber HCPRS Hurricane/Seismic Anchor USP Lumber MSTA36-TZ Medium Capacity Strap Tie
For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. One piece, designed to work with single, solid sawn beams, but can be used with build-up beams made of 2x lumber and shims fastened together to act as a unit. Requires 16d HDG nails for installation. Meets ICC-ES ESR-1280, FL11664, L.A. City RR25749 and Dade County, FL 07-0306.06 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 18 GAUGE. Used to tie trusses and rafters to top plates, and may be used to tie wood framing members to resist uplift and lateral forces. G90 galvanizing finish. 1-9/16"W opening. Meets ICC-ES ESR-1881, FL821 and L.A. City RR25779 codes. 18 Gauge - 5-1/4"W. Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes.
USP Lumber TSX24 Truss Spacer USP Lumber JDS24-S Double Shear Single Purlin Hanger USP Lumber NP39 Truss Mending Plate
Fast and accurate spacing guides for trusses, rafters or floor joists. Lightweight and compact, eliminates need to mark layouts on bearing plates, improves installation speed and helps to eliminate spacing errors. Do not rely on TSX  for bracing. Requires one 8d nail per end. 10'L overall; 24" O.C. spacing. 22 Gauge - 5 Sections/Piece. Designed for quick installation of purlins between rafters, joists or trusses in post and beam structures. One-piece construction assures a consistent flush fit between purlin and joist or rafter. A reinforced "double lap" seat boosts the load capacity of this heavy-duty purlin hanger. Requires (2) 10d x 1-1/2"nails for header and (2) 10d nails for each purlin. Features a 3/4" top fold; pending IAMPO-ES evaluation. Joins flat surfaces of 2 or more wood members. Not for structural use or use in truss assembly. G90 galvanizing finish. Use nails appropriate for intended use. Holes sized for 8d common or 8d x 1-1/2" nails. 20 Gauge.
USP Lumber ICPL58-TZ Protection Plate USP Lumber ICPL516-TZ Protection Plate USP Lumber CPB Composite Post Base
Easy-to-install plates protect plumbing and power/communication wiring from nail or screw penetration. 16 Gauge - 1/16" Thickness. Easy-to-install plates protect plumbing and power/communication wiring from nail or screw penetration. 16 Gauge - 1/16" Thickness. Provides a raised base that elevates wood posts above concrete surfaces to avoid moisture from ground contact. Single-piece design made from composite material; will not corrode. Open center enables installation of metal rod from concrete into post. Not for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning moment loads. Requires (4) 10d HDG nails. ACQ approved.
USP Lumber LSSH15-TZ Slope/Skew Joist Hanger USP Lumber JUS28-2TZ Double Shear Slant Joist Hanger USP Lumber SKH28L Skewed Left Joist Hanger
Connects rafters to ridge beams in vaulted roof structures; field adjustable to meet a variety of skew and slope applications; slopes to any pitch to 45 degrees up or down and skews up to 45 degrees right or left.  For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments.
USP Lumber SKH28R Skewed Right Joist Hanger USP Lumber MP9-TZ Framing Angle USP Lumber THF25112 Joist Hanger
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. May be field adjusted by hand from 0 to 135 degrees, giving framers and do-it-yourselfers flexibility in applications. Bend angle only once. G90 galvanized finish. 10d HDG nails required for installation. Meets SBCCI, BOCA - NER 530, ICBO 5700, FL822, L.A. City RR 25337, DSA PA-06 codes. Designed to provide lateral support for the top chords of I-Joists in depths up to 16". G90 galvanizing finish. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. Install 10d x 1-1/2" nails into joist through raised dimple at 45 degree angle. For THF Min, fill all round nail holes. For THF Max, fill all round and diamond holes. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com.
Mutual 14640-3 Standard Rebar Cap USP Lumber DTB Deck Tie Bracket USP Lumber MTW18 Medium Capacity Twist Strap
Mushroom style rebar safety caps protect from protruding rebar at construction sites. Bright colors for excellent visibility. Use where the danger of impalement is not present. Used to reinforce the connection of rail posts to a deck. Also provides lateral strength of deck-to-ledger attachment by securing deck to house framing. Installs with 1/2" anchor bolt (not included) and 8" WS15-GC Wood screws (included). G185 galvanizing finish. Pending IAPMO-ES ER-0200 and FL14500 codes. Use to tie framing members to resist tension forces as in stud plate-rim joist and truss-to-top-plate installations. Flat transition bend, for easy installation, splits total length into 2 separate, equal lengths (L1 & L2). G90 galvanizing finish. Requires an equal number of 10d or 10d x 1-1/2 fasteners at each end. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber C 1-Piece Post Cap USP Lumber MB16 Snap-On Joist Bridging USP Lumber SKH26R-TZ Skewed Right Joist Hanger
For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. One piece, designed to work with single, solid sawn beams, but can be used with build-up beams made of 2x lumber and shims fastened together to act as a unit. Requires 16d HDG nails for installation. Meets ICC-ES ESR-1280, FL11664, L.A. City RR25749 and Dade County, FL 07-0306.06 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 18 GAUGE. No-nail bridging. Place in existing floor system where joist movement is suspected to reduce movement and subsequent floor noise. 2 piece construction creates a solid diagonal brace against joist movement. G90 galvanizing finish. Shipped as 1 piece that easily breaks into 2 pieces at center for proper installation. Meets ICC-ES ESR-1781, FL3285 and L.A. City RR25843 codes. For additional information on standard lumber installation, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 22 Gauge - 2 x 8-10-12 Joist Size. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments.
USP Lumber SKH26L-TZ Skewed Left Joist Hanger USP Lumber AC9-TZ Framing Angle USP Lumber O16 Joist Bridging
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting and allows installation on both sides of the supported member. Triple Zinc clips require 10d HDG or 16d HDG nails.  Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Spans three joists in under/over installation; prong teeth in the center helps reduce nailing. G90 galvanizing finish; bridging should be installed on floor joists with a nominal depth-to-thickness ratio of 5 to 6 or more (2055 National Design Specification for Wood Construction; Section 4.4.1). Install prior to subfloor sheathing; use (2) 8d x 1-1/2" nails at each end. Fully seat nails to avoid any movement against the bridging and subsequent floor noise. 18 Gauge.
USP Lumber AC5-TZ Framing Angle USP Lumber JNP24 Joiner Nail Mending Plate USP Lumber PA66-TZDP Post Anchor
For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting and allows installation on both sides of the supported member. Triple Zinc clips require 10d HDG or 16d HDG nails.  Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Prong plates with angled, hammer-in prongs. Joins flat surfaces of 2 or more wood members. G90 galvanizing finish. Not intended for structural use OR in truss assembly. No load ratings assigned. 18 Gauge. Used to secure wood posts to concrete footings and to provide moisture damage protection. 4-sided with high uplift and bearing capacity. Features a 1" stand-off plate to elevate wood posts above concrete surfaces. Drain slots allow the anchors to shed water. Triple zinc finish for ACQ pressure treated lumber. Not for fence posts or unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires 16d nails for installation. Meets ICC-ES ESR-1831, FL822 and L.A. City RR25836 codes.
Deckmaster DMP100-100 Hidden Deck Bracket Kit Deckmaster DMP125-100 Hidden Deck Bracket Kit USP Lumber TDX2-TZ Holdown
System eliminates the damage to deck boards by hiding all fasteners beneath deckboards. Holds boards tight to eliminate any surface penetration. No moisture can enter deckboards or joists and cause nail penetration. No moisture can enter deckboards or joists and cause nail or screw pop-ups or deck rot. No stains or splinters form around fastener holes. Corrosion resistance. Powder coating's natural wood color blends with the understructure of balconies.  Contractor pack includes: 100 brackets, (1200) 10 x 1-1/4" deck board screws, (1100) 8 x 1" joist screws, and a pro bit tip. Use the Contractor pack for large decks. System eliminates the damage to deck boards by hiding all fasteners beneath deckboards. Holds boards tight to eliminate any surface penetration. No moisture can enter deckboards or joists and cause nail penetration. No moisture can enter deckboards or joists and cause nail or screw pop-ups or deck rot. No stains or splinters form around fastener holes. Corrosion resistance. Powder coating's natural wood color blends with the understructure of balconies.  Contractor pack includes: 100 brackets, (1200) 10 x 1-1/4" deck board screws, (1100) 8 x 1" joist screws, and a pro bit tip. Use the Contractor pack for large decks. Used to tie first and second story framing together, anchor studs to foundations or to tie purlins to masonry or concrete. Features self-jigging, formed design with code required distances built-in. Requires 7/8", 5/8, and 3/4" bolts for installation. Meets IAPMO-ES ER-0200 and FL14500 codes. For additional information including allowable loads and number of fastener, please see USP Lumbar Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JNP28 Joiner Nail Mending Plate USP Lumber AC Framing Angle USP Lumber STS1 Single Stud Joist Hanger
Prong plates wit