Home > HARDWARE > CONSTRUCTION HARDWARE > VENTILATION PRODUCTS > SIDING VENTS
Sort By:
1
USP Lumber JL26IF-TZ Standard Invert Flange Joist Hanger Acorn BT176-1C Bar Tie USP Lumber JDS24 Double Shear Saddle Purlin Hanger
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Used to secure the position of rebar during concrete pouring. Designed for quick installation of purlins between rafters, joists or trusses in post and beam structures. One-piece construction assures a consistent flush fit between purlin and joist or rafter. A reinforced "double lap" seat boosts the load capacity of this heavy-duty purlin hanger. Requires (4) 10d x 1-1/2" nails for header and (4) 10d" nails for each purlin. Features a 1-9/16" top fold; pending IAPMO-ES evaluation.
Professional 5010 Ceiling Lag Screw Set USP Lumber JL28IF-TZ Standard Invert Flange Joist Hanger Maurice Franklin RL-100 Round Screen Louver
Use to hold ceiling hanging wire. Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Maurice Franklin Screen Louver, Round, Series: RL-100, 3/16 sq-in Net Free Area, 1 in Cutout Width, 13/32 in Cutout Height, 5 Blades, Aluminum, Mill, 0.02 ga Thickness, 1.219 in Overall Width
Maurice Franklin PLW-100 Round Screen Louver USP Lumber JUS210-2TZ Double Shear Slant Joint Hanger Marshalltown 14731 Manual Tie Wire Twister
One piece white polyethylene. Recommended for moisture control in sidewalls construction or other restricted areas. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Safely and easily twists wire bar ties. Plastic handle. Rugged design. Compact size allows the tool to be used in tight space.
Mintcraft 16570 Rugged Wire Twister Maurice Franklin RLW-100 Round Screen Louver EXTENSION DOWNSPOUT 26X9X23IN
Safely and easily twists wire bar ties. Hardwood handle, Ergonomic design. Maurice Franklin Screen Louver, Round, Series: RLW-100, 3/16 sq-in Net Free Area, 1 in Cutout Width, 13/32 in Cutout Height, 5 Blades, Aluminum, White, 0.02 ga Thickness, 1.219 in Overall Width Allows you to extend water flow to your desired location for ideal distribution when used with the StealthFlow? low profile downspout extension kit (sku 358.2301). The extension is made from durable resin with a low-profile design that disappears into your landscaping for a subtle appearance. The extension features a snap-together design for simple installation without the need for tools.
Billy Penn 08212-25 Manual Bar Tie Twister Maurice Franklin RL-100 Round Screen Louver EXTENSN ELBW ADJSTBL 9X15X23IN
Makes tying fast and easy. Wood handle. Maurice Franklin Screen Louver, Round, Series: RL-100, 1.21 sq-in Net Free Area, 2-1/2 in Cutout Width, 5/8 in Cutout Height, 6 Blades, Aluminum, Mill, 0.02 ga Thickness, 2.907 in Overall Width An accessory item in the StealthFlow? family of products. The adjustable elbow allows the StealthFlow? low profile downspout extension kit the ability to divert water around landscaping and corners. The elbow slides to adjust to angles between 45 and 90 degrees in order to customize for your application or situation.
Maurice Franklin RLW-100 Round Screen Louver Maurice Franklin RLB-100 Round Screen Louver Maurice Franklin PLW-100 Round Screen Louver
Maurice Franklin Screen Louver, Round, Series: RLW-100, 1.21 sq-in Net Free Area, 2-1/2 in Cutout Width, 5/8 in Cutout Height, 6 Blades, Aluminum, White, 0.02 ga Thickness, 2.907 in Overall Width Maurice Franklin Screen Louver, Round, Series: RLB-100, 1.21 sq-in Net Free Area, 2-1/2 in Cutout Width, 5/8 in Cutout Height, 6 Blades, Aluminum, Brown, 0.02 ga Thickness, 2.907 in Overall Width One piece white polyethylene. Recommended for moisture control in sidewalls construction or other restricted areas.
Quik-Tube 6922-01 Building Form Maurice Franklin PLW-100 Round Screen Louver Maurice Franklin PLB-100 Round Screen Louver
Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed. One piece white polyethylene. Recommended for moisture control in sidewalls construction or other restricted areas. One piece white polyethylene. Recommended for moisture control in sidewalls construction or other restricted areas.
Maurice Franklin RLW-100 Round Screen Louver Professional TP05044 Lever Grid Leveling Clamp Maurice Franklin RL-100 Round Screen Louver
Maurice Franklin Screen Louver, Round, Series: RLW-100, 0.399 sq-in Net Free Area, 1-1/2 in Cutout Width, 9/16 in Cutout Height, 5 Blades, Aluminum, White, 0.02 ga Thickness, 1.813 in Overall Width Holds jet line and angle to grid; lever style; 4-pack tube. Maurice Franklin Screen Louver, Round, Series: RL-100, 0.803 sq-in Net Free Area, 2 in Cutout Width, 5/8 in Cutout Height, 6 Blades, Aluminum, Mill, 0.02 ga Thickness, 2.391 in Overall Width
Maurice Franklin RL-100 Round Screen Louver Maurice Franklin RLB-100 Round Screen Louver Maurice Franklin RLW-100 Round Screen Louver
Maurice Franklin Screen Louver, Round, Series: RL-100, 1.735 sq-in Net Free Area, 3 in Cutout Width, 11/16 in Cutout Height, 6 Blades, Aluminum, Mill, 0.02 ga Thickness, 3-17/32 in Overall Width Maurice Franklin Screen Louver, Round, Series: RLB-100, 0.803 sq-in Net Free Area, 2 in Cutout Width, 5/8 in Cutout Height, 6 Blades, Aluminum, Brown, 0.02 ga Thickness, 2.391 in Overall Width Maurice Franklin Screen Louver, Round, Series: RLW-100, 0.803 sq-in Net Free Area, 2 in Cutout Width, 5/8 in Cutout Height, 6 Blades, Aluminum, White, 0.02 ga Thickness, 2.391 in Overall Width
Maurice Franklin RLB-100 Round Screen Louver Maurice Franklin RLW-100 Round Screen Louver Professional TP05032 Acoustical Lag Driver
Maurice Franklin Screen Louver, Round, Series: RLB-100, 1.735 sq-in Net Free Area, 3 in Cutout Width, 11/16 in Cutout Height, 6 Blades, Aluminum, Brown, 0.02 ga Thickness, 3-17/32 in Overall Width Maurice Franklin Screen Louver, Round, Series: RLW-100, 1.735 sq-in Net Free Area, 3 in Cutout Width, 11/16 in Cutout Height, 6 Blades, Aluminum, White, 0.02 ga Thickness, 3-17/32 in Overall Width Drive eye lag screws into wood or metal with screwgun or drill. Carded.
Quikrete 6922-02 Concrete Quik-Tube Form Flex-A-Spout 85014 Flexible Downspout Extension Flex-A-Spout 85011 Corrugated Flexible Rigid Downspout Extension
Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed. Flexible tube easily attaches to the downspout with sheet metal screws (not included). Can be bent into the desired water flow direction, or can be buried out of sight. Retains shape. Fits 2" x 3" or 3" x 4" downspouts. Expands from 22" to 55", to get water further away from the foundation. Two or more sections can be snapped together to get longer lengths. Flexible tube easily attaches to the downspout with sheet metal screws (not included). Can be bent into the desired water flow direction, or can be buried out of sight. Retains shape. Fits 2" x 3" or 3" x 4" downspouts. Expands from 22" to 55", to get water further away from the foundation. Two or more sections can be snapped together to get longer lengths.
Flex-A-Spout 85010 Corrugated Rigid Downspout Extension Flex-A-Spout 85019 Corrugated Flexible Downspout Extension Maurice Franklin PLW-100 Round Screen Louver
Flexible tube easily attaches to the downspout with sheet metal screws (not included). Can be bent into the desired water flow direction, or can be buried out of sight. Retains shape. Fits 2" x 3" or 3" x 4" downspouts. Expands from 22" to 55", to get water further away from the foundation. Two or more sections can be snapped together to get longer lengths. Flexible tube easily attaches to the downspout with sheet metal screws (not included). Can be bent into the desired water flow direction, or can be buried out of sight. Retains shape. Fits 2" x 3" or 3" x 4" downspouts. Expands from 22" to 55", to get water further away from the foundation. Two or more sections can be snapped together to get longer lengths. One piece white polyethylene. Recommended for moisture control in sidewalls construction or other restricted areas.
Maurice Franklin RL-100 Round Screen Louver EXTENSN DOWNSPT KIT 29X18X23IN Professional 5015 Ceiling Lag Screw Set
Maurice Franklin Screen Louver, Round, Series: RL-100, 3.5 sq-in Net Free Area, 4 in Cutout Width, 3/4 in Cutout Height, 9 Blades, Aluminum, Mill, 0.02 ga Thickness, 4-5/8 in Overall Width Allows you to extend water flow to your desired location for ideal distribution when used with the StealthFlow? low profile downspout extension kit (sku 358.2301). The extension is made from durable resin with a low-profile design that disappears into your landscaping for a subtle appearance. The extension features a snap-together design for simple installation without the need for tools. Use to hold ceiling hanging wire.
Professional 5110 Shadowline Edge Cutter Professional 5122 Ceiling Wire Maurice Franklin RLW-100 Round Screen Louver
Metal shadowline cutter for ceiling tile. Fits comfortably in hand. Lightweight and includes 5 blades. Galvanized 18 gauge wire in a convenient belt dispenser. Maurice Franklin Screen Louver, Round, Series: RLW-100, 3.5 sq-in Net Free Area, 4 in Cutout Width, 3/4 in Cutout Height, 9 Blades, Aluminum, White, 0.02 ga Thickness, 4-5/8 in Overall Width
Maurice Franklin RLB-100 Round Screen Louver Quik-Tube 6922-03 Building Form USP Lumber SKH28R-TZ Skewed Left Joist Hanger
Maurice Franklin Screen Louver, Round, Series: RLB-100, 3.5 sq-in Net Free Area, 4 in Cutout Width, 3/4 in Cutout Height, 9 Blades, Aluminum, Brown, 0.02 ga Thickness, 4-5/8 in Overall Width Used by homeowners and residential contractors to create everything from lamp post and mailbox bases to deck supports. Easy-to-use cardboard tube, scaled-down version of rigid fiber forms that heavy-construction contractors use. Pour concrete in form, let it dry, then cut away form. Length can be cut down if needed. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments.
USP Lumber SKH28L-TZ Skewed Left Joist Hanger FORM CONCRETE FOOT PLASTC 22IN FORM CONCRETE FOOT PLASTC 28IN
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed. Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed.
Marshalltown TWR26 Tie Wire Reel Professional 5060 Grid Punch ANGLE 2X4IN TRIPLE ZINC 12GA
Made of lightweight durable plastic to give many years of trouble free use. Fits any standard size belt. Accomodates all types of tie wire. Use when installing suspended ceiling grid. Use to connect grid cut at non-standard lengths. Punch holes 1/8" rivets, punches 9/16" grid. Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong.
USG 207535 Hanger Wire Easy Heat ADKS Fixed Resistance Roof and Gutter De-Icing Kit Easy Heat ADKS Fixed Resistance Roof and Gutter De-Icing Kit
Galvanized 12 gauge wire. Roof and Gutter Deicing Cable prevents costly damage to roofs caused by ice formation and snow accumulation in gutters, downspouts, and roof valleys. Can be applied anywhere melting snow and ice can refreeze and penetrate roof surface causing leaks and related damage. Versatile design and rugged waterproof construction adapts to most roof and gutter configurations. Roof and Gutter Deicing Cable prevents costly damage to roofs caused by ice formation and snow accumulation in gutters, downspouts, and roof valleys. Can be applied anywhere melting snow and ice can refreeze and penetrate roof surface causing leaks and related damage. Versatile design and rugged waterproof construction adapts to most roof and gutter configurations.
ANGLE 2X6IN TRIPLE ZINC 12GA  USP Lumber JL24 Standard Joist Hanger Marshalltown TWR19 Tie Wire Reel
Provides a 90? connection for medium/heavy duty applications; stronger than angled nailing or screw fastening; help ensure joints are consistently straight and strong. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Constructed of light weight aluminum. Designed for left or right hand use. Large knob provides smooth operation. Accommodates all types of tie wire rolls. Fits any standard size belt.
DE-ICING CABLE 150W 30FT KIT  Acorn BT174-5M Bar Tie USP Lumber MP34 Framing Angle
De-icing cable kit prevents winter damage to roof, gutters, and downspouts. Used to secure the position of rebar during concrete pouring. Use for joist/header installations. Does not have tabs. G90 galvanizing finish. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505; ICBO 5736; DSA PA-076; Dade County, FL 01-0417.11; and  L.A. City RR25303 codes. 18 Gauge.
USP Lumber RT7A Double Plate Hurricane/Seismic Anchor USP Lumber JL26 Standard Joist Hanger National Nail 1/2X6 Pre-Formed Anchor Bolt
Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Acorn BT175-5M Bar Tie FORM CONCRETE FOOT PLASTC 32IN National Nail 3/8X8 Pre-Formed Anchor Bolt
Used to secure the position of rebar during concrete pouring. Fastest, easiest way to form concrete footings; patented square footing form decreases cycle time, labor and material cost; can be sized, attached to construction tube, placed in excavated hole and backfilled. Can be used with rebar to reinforce footing or column if needed. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
Frost King RC Roof De-Icing Cable With Shingle Clips USP Lumber RT3A Double Plate Hurricane/Seismic Anchor DE-ICING CABLE 300W 60FT KIT
Pre-assembled ready to install, keeps gutters and downspouts flowing, 120v, 7 watts per ft. Ties trusses and rafters to top plates either left or right handed. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. G90 galvanizing finish. Requires 8d nails for installation in plate and rafter/truss. Meets ICC-ES ESR-1465 and FL817 codes. 18 Gauge. De-icing cable kit prevents winter damage to roof, gutters, and downspouts.
Easy Heat ADKS Fixed Resistance Roof and Gutter De-Icing Kit Acorn BT176-1M/5M Bar Tie USP Lumber JUS28 Double Shear Slant Joist Hanger
Roof and Gutter Deicing Cable prevents costly damage to roofs caused by ice formation and snow accumulation in gutters, downspouts, and roof valleys. Can be applied anywhere melting snow and ice can refreeze and penetrate roof surface causing leaks and related damage. Versatile design and rugged waterproof construction adapts to most roof and gutter configurations. Used to secure the position of rebar during concrete pouring. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT Hurricane/Seismic Anchor National Nail 1/2X8 Pre-Formed Anchor Bolt National Nail AG5810 Pre-Formed Anchor Bolt
Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
National Nail AG5808 Pre-Formed Anchor Bolt USP Lumber JL28 Standard Joist Hanger USP Lumber RT8A Double Plate Hurricane/Seismic Anchor
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc anchors (310.1573) requires 8d HDG nails and Gold Coat anchors (947.3265) requires N8-GC nails.  Meets ICC-ES ESR-1465 and FL817 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber ST1-TZ Mud Sill Anchor USP Lumber JA1 Joist Angle USP Lumber JA1-TZ Framing Angle
For securing mudsills and framing into concrete slabs or poured stemwalls. Not for block installation or securing concrete sections together between cold joints. Features prebent base flange for proper anchoring into concrete. Use a minimum of 2 anchors per mudsill within 12" of the end of each section. Meets  NER 530 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Used to strengthen framing in various applications or to support joists where stirrup style hangers cannot be installed. Requires 10d x 1-1/2 nails for installation. Meets ICBO, SBCCI, BOCA - NER 505; L.A. City RR25303, DSA PA-076; and Dade County, FL 98-0421.06 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 16 Gauge. Used to strengthen framing in various applications or to support joists where stirrup style hangers cannot be installed. Requires 10d x 1-1/2 nails for installation. Meets ICBO, SBCCI, BOCA - NER 505; L.A. City RR25303, DSA PA-076; and Dade County, FL 98-0421.06 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. 16 Gauge.
U-CLIP 2X-2X TRIPLE ZINC      Easy Heat ADKS Fixed Resistance Roof and Gutter De-Icing Kit USP Lumber KHL33 Heavy Joist Angle
A clip connects a 2x wood member to the face of another wood member; 20 gauge; G-185 galvanizing finish; requires (6) USP LumberLok LL915 (#9 x 1-3/8" long) wood screws not included. Roof and Gutter Deicing Cable prevents costly damage to roofs caused by ice formation and snow accumulation in gutters, downspouts, and roof valleys. Can be applied anywhere melting snow and ice can refreeze and penetrate roof surface causing leaks and related damage. Versatile design and rugged waterproof construction adapts to most roof and gutter configurations. Designed for heavy-duty reinforcement of 90 degree framing intersections. USP primer finish. Requires (2) 5/8" bolts for installation. Meets ICBO 2725, L.A. City RR 25104. 7 Gauge.
National Nail AG06 Pre-Formed Anchor Bolt National Nail AG08 Pre-Formed Anchor Bolt USP Lumber JUS28-TZ Double Shear Slant Joint Hanger
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
Frost King RC Roof De-Icing Cable With Shingle Clips National Nail 1/2X10 Pre-Formed Anchor Bolt Acorn BT178-5M Bar Tie
Pre-assembled ready to install, keeps gutters and downspouts flowing, 120v, 7 watts per ft. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Used to secure the position of rebar during concrete pouring.
Easy Heat ADKS Fixed Resistance Roof and Gutter De-Icing Kit National Nail AG5812 Pre-Formed Anchor Bolt National Nail AG10 Pre-Formed Anchor Bolt
Roof and Gutter Deicing Cable prevents costly damage to roofs caused by ice formation and snow accumulation in gutters, downspouts, and roof valleys. Can be applied anywhere melting snow and ice can refreeze and penetrate roof surface causing leaks and related damage. Versatile design and rugged waterproof construction adapts to most roof and gutter configurations. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete.
USP Lumber JUS210 Double Shear Slant Joist Hanger National Nail 1/2X12 Pre-Formed Anchor Bolt USP Lumber BL Corner Brace
Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. Reinforces 90 degree wood-to-wood connections. G90 galvanizing finish. Requires 16d nails for installation. 12 Gauge.
National Nail AG12 Pre-Formed Anchor Bolt DE-ICING CABLE 500W 100FT KIT USP Lumber JL210 Standard Joist Hanger
Pre-formed bolt designed for anchoring to concrete in all construction work. Hold securely and permanently because of the angle design. Designed for all types of anchoring to poured concrete. De-icing cable kit prevents winter damage to roof, gutters, and downspouts. G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
HANGER RIDGE RAFTER 18 GAUGE  USP Lumber JUS24 Double Shear Slant Joist Hanger USP Lumber JUS24-TZ Double Shear Slant Joint Hanger
Supports rafter pitches up to 7:12 (30?). Nesting top flange for installation on 2x support beams. Use all specified fasteners. The rafter end at the ridge must be plumb cut to achieve published loads. Optional diamond nail holes can be used to faster RR to end of rafter before settling rafter into place. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT15 Double Plate Hurricane/Seismic Anchor USP Lumber MPA1 Framing Angle Easy Heat ADKS Fixed Resistance Roof and Gutter De-Icing Kit
Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc finish requires 8d HDGnails for installation in plate and rafter/truss and Gold Coat anchor requires N8-GC nails. 1-9/16"W x 2-5/8"H opening. Meets ICC-ES ESR-1465, FL817 and Dade County, FL 07-0306.10 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Contractors charts in the Orgill paper catalog R7 for reference pages. 18 GAUGE - 5-1/4"H. Use for joist to header, rafter to plate, stud to plate or 1" foamboard installations. Achieves continuous load path in high wind and seismic resistant construction. Enables quick field adjustments for 2 and 3-way connections. Tabs enable two and three-way connections. Bend tabs only once. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505, ICBO 5736, DSA PA-076, Dade County, FL 01-417.11 and  L.A. City RR25303 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Roof and Gutter Deicing Cable prevents costly damage to roofs caused by ice formation and snow accumulation in gutters, downspouts, and roof valleys. Can be applied anywhere melting snow and ice can refreeze and penetrate roof surface causing leaks and related damage. Versatile design and rugged waterproof construction adapts to most roof and gutter configurations.
DE-ICING CABLE 600W 120FT KIT ANGLE 2X-2X TRIPLE ZINC 16GA  USP Lumber JUS26 Double Shear Slant Joist Hanger
De-icing cable kit prevents winter damage to roof, gutters, and downspouts. An angle connects two 2x wood members at 90? angles; G185 galvanizing finish; requires (8) USP LumberLok LL915 (#9 x 1-3/8" long) wood screws not included. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS26-TZ Double Shear Slant Joint Hanger USP Lumber RT Hurricane/Seismic Anchor USP Lumber MPA1 Framing Angle
Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Ties trusses and rafters to top plates. Can use to tie wood framing members to resist uplift and lateral forces. Seismic, tested for lateral movement. Triple Zinc finish requires 8d HDGnails for installation in plate and rafter/truss and Gold Coat anchor requires N8-GC nails. 1-9/16"W x 2-5/8"H opening. Meets ICC-ES ESR-1465, FL817 and Dade County, FL 07-0306.10 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber Contractors charts in the Orgill paper catalog R7 for reference pages. 18 GAUGE - 5-1/4"H. Use for joist to header, rafter to plate, stud to plate or 1" foamboard installations. Achieves continuous load path in high wind and seismic resistant construction. Enables quick field adjustments for 2 and 3-way connections. Tabs enable two and three-way connections. Bend tabs only once. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505, ICBO 5736, DSA PA-076, Dade County, FL 01-417.11 and  L.A. City RR25303 codes. For additional information including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS210-TZ Double Shear Slant Joint Hanger Easy Heat RS2 Roof Sentry De-Icing Control USP Lumber JUS26-2 Double Shear Slant Support Joist Hanger
Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Controller for the roof and gutter de-icer cable. Controller requires two conditions to be present before it will energize the roof de-icing cable. It requires cold temperatures and the presence of run-off water from the roof in contact with the sensor wire. If only one of the conditions exists, the control will not turn on the cable. A switch inside the house can control the box. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
Donn Dx SDX216 Cross Tee USP Lumber TFL2595 Joist Hanger USP Lumber BL Reinforcement Corner Brace
Offers maximum economy, simplicity and accessibility; its hot-dipped, galvanized steel construction provides corrosion resistance and ensures paint adhesion; easy installation with "Quick-Release" cross tee clip; the clips are easy to remove without tools, minimizing tee damage. White. Features 1-1/2" top flange depth that accommodates all header types as well as back-to-back installations. Features "Seat Cleat" for quick, positive seating. G90 galvanizing finish. Meets ICC-ES ESR-1831 codes. Header requires (6) 10d nails and joist requires (2) 10d x 1-1/2 nails for installation. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge. Reinforces 90 degree wood-to-wood connections. G90 galvanizing finish. Requires 16d nails for installation. 12 Gauge.
USP Lumber ST2-TZ Mud Sill Anchor Quikrete 6917-03 Expansion Joint USP Lumber JUS26-2TZ Double Shear Slant Joint Hanger
For securing mudsills and framing into concrete slabs, poured stemwalls, or concrete block. Not for securing concrete sections together between cold joints. Features prebent base flange for proper anchoring into concrete. Use a minimum of 2 anchors per mudsill within 12" of the end of each section. Meets NER 530 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Used where concrete meets concrete for a stronger bond. Expansion joint filler made from resilient wood to prevent damage during expansion and contraction of concrete. Used in driveways, sidewalks, and patios, between concrete slabs and to separate slabs from structures. Meets requirements of ASTM D 1751. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber JUS210-2 Double Shear Slant Support Joist Hanger USP Lumber TFL20118 Joist Hanger USP Lumber JUS28-2 Double Shear Slant Joist Hanger
Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Features 1-1/2" top flange depth that accommodates all header types as well as bact-to-back installations. Features "Seat Cleat" for quick, positive seating. G90 galvanizing finish. Meets ICC-ES ESR-1831. Header requires (6) 10d nails and joist requires (2) 10d x 1-1/2" nails for installation. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber SCA Stair Angle USP Lumber TFL25118 Joist Hanger USP Lumber RT10 Double Plate Hurricane/Seismic Anchor
Simplifies stair construction and eliminate the need to calculate and notch stair stringers. Stronger and safer than wood blocking, and the angle and fasteners are hidden from view. Use the SCA9 for single 2x10 stair treads and SCA10 for double 2 x 6 stair treads. Requires 1/4" x 1-1/2" lag bolts. Meets ICC-ES ESR-1280, FL11664 and L.A. City RR25749 codes. For additional information on installation, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Features 1-1/2" top flange depth that accommodates all header types as well as back-to-back installations. Features "Seat Cleat" for quick, positive seating. G90 galvanizing finish. Meets ICC-ES ESR-1831 codes. Header requires (6) 10d nails and joist requires (2) 10d x 1-1/2 nails for installation. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge. Used to tie wood framing members to resist uplift and lateral forces. G90 galvanizing finishing. Requires 8d nails for installation. Meets ICC-ES ESR-1465, FL817 and Dade County, FL 07-0306.10 codes. 18 Gauge.
USP Lumber CSH-TZ Concealed Stringer Hanger Deacero 5689/RBTW35 Coil Tie Wire USP Lumber WE44-TZ Wet Post Anchor
Concealed stair stringer hanger provides a method of connecting a stringer with a hidden hanger. The seat of the hanger is adjustable to match the slope of the stair stringer. Triple Zinc finish. Requires (8) 10d x 1-1/2 HDG nails for header and (5) 10d x 1-1/2 HDG nails for joist. 18 Gauge. Pending IAPMO-ES evaluation. Center hole (semi-square with round corners) enables roll to be quickly reversed for right or left hand use. Roll slips quickly onto the reel, yet easily rewinds. Continuous rolls and uniform diameters. Ideal to tie rods. Meets ASTM-A-853. 16.5 gauge. 3.5 pound coil. Secures posts to concrete in light-duty and medium-duty applications such as patio covers, carports or decks. Formed, one-piece design includes embossing for additional lateral strength. Not  for fence posts or other unrestrained (not fixed or fastened at top) applications. Not designed to resist overturning (moment) loads. Requires (2) 1/2" HDG bolts or (12) HDG nails for fastening to post. Meets SBCCI, BOCA - NER 530 & NER 608, ICBO 5700, ICBO 2039, ICBO 5531, FL821, FL822, L.A. City RR 25337, and DSA PA-076 codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber RT16A Double Plate Hurricane/Seismic Anchor Donn Dx SDX24 Main Tee USP Lumber A3 Framing Angle
Anchor tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces. Typical Truss/rafter to double plate installation. Requires Meet ICC-ES ESR-1465 and FL817 codes. The USG "DONN SDX/SDXL" Ceiling Suspension System offers maximum economy, simplicity and accessibility; galvanized steel construction provides corrosion resistance and ensures paint adhesion; easy installation with the "Quick-Relaease" cross tee clip; the clips are easy to remove without tools, minimizing tee damage. Color: White. Eliminates toenailing and increases strength. Requires 10d x 1-1/2" nails for installation. 1-7/16"W1 X 1-7/16"W2 X 2-3/4"L - 18 GAUGE. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes.
Donn Dx SDX424 Cross Tee USP Lumber SCA Stair Angle USP Lumber JUS26-GC Double Shear Slant Joist Hanger
Offers maximum economy, simplicity and accessibility; its hot-dipped, galvanized steel construction provides corrosion resistance and ensures paint adhesion; easy installation with "Quick-Release" cross tee clip; the clips are easy to remove without tools, minimizing tee damage. White. Simplifies stair construction and eliminate the need to calculate and notch stair stringers. Stronger and safer than wood blocking, and the angle and fasteners are hidden from view. Use the SCA9 for single 2x10 stair treads and SCA10 for double 2 x 6 stair treads. Requires 1/4" x 1-1/2" lag bolts. Meets ICC-ES ESR-1280, FL11664 and L.A. City RR25749 codes. For additional information on installation, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. Double shear nailing for fewer nails and faster installation. Dimples allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade County, FL 11-0510.01 and 07-0419.01codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber HCPRS Hurricane/Seismic Anchor USP Lumber JDS24-S Double Shear Single Purlin Hanger USP Lumber THF25112 Joist Hanger
Used to tie trusses and rafters to top plates, and may be used to tie wood framing members to resist uplift and lateral forces. G90 galvanizing finish. 1-9/16"W opening. Meets ICC-ES ESR-1881, FL821 and L.A. City RR25779 codes. 18 Gauge - 5-1/4"W. Designed for quick installation of purlins between rafters, joists or trusses in post and beam structures. One-piece construction assures a consistent flush fit between purlin and joist or rafter. A reinforced "double lap" seat boosts the load capacity of this heavy-duty purlin hanger. Requires (2) 10d x 1-1/2"nails for header and (2) 10d nails for each purlin. Features a 3/4" top fold; pending IAMPO-ES evaluation. Designed to provide lateral support for the top chords of I-Joists in depths up to 16". G90 galvanizing finish. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. Install 10d x 1-1/2" nails into joist through raised dimple at 45 degree angle. For THF Min, fill all round nail holes. For THF Max, fill all round and diamond holes. For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com.
USP Lumber LSSH15-TZ Slope/Skew Joist Hanger Donn SM7 Wall Molding USP Lumber JUS28-2TZ Double Shear Slant Joist Hanger
Connects rafters to ridge beams in vaulted roof structures; field adjustable to meet a variety of skew and slope applications; slopes to any pitch to 45 degrees up or down and skews up to 45 degrees right or left.  For information including allowable loads and number of fasteners, please see USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages. For additional sizing information, visit www.uspconnectors.com. 18 Gauge. Angle moldings are "L" shaped wall moldings used at the perimeter of a ceiling. USG "DONN" Ceiling Suspension System Moldings help achieve the aesthetic and performance characteristics one needs, including seismic requirements and humidity resistance. White. Double shear nailing for fewer nails and faster installation. Dimples allow for 45 degree nailing through joist into header, resulting in higher loads and less nailing, and eliminate need for shorter joist nails in 2x applications. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779, Dade county, FL 11-0510.01 and 07-0419.01 codes. For additional information including allowable loads and fasteners. Please See USP Lumber Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber SKH28L Skewed Left Joist Hanger USP Lumber SKH28R Skewed Right Joist Hanger USP Lumber MP9-TZ Framing Angle
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. May be field adjusted by hand from 0 to 135 degrees, giving framers and do-it-yourselfers flexibility in applications. Bend angle only once. G90 galvanized finish. 10d HDG nails required for installation. Meets SBCCI, BOCA - NER 530, ICBO 5700, FL822, L.A. City RR 25337, DSA PA-06 codes.
USP Lumber SKH26R-TZ Skewed Right Joist Hanger USP Lumber SKH26L-TZ Skewed Left Joist Hanger USP Lumber AC9-TZ Framing Angle
Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. Standard stock 45 degree skew hanger for common standard lumber, engineered lumber and plated truss applications. Flexible design for 40 to 50 degree skew range. Meets ICC-ES ESR-1781, FL13285, L.A. City RR25843 and Dade County, FL 11-0510.01 codes. For additional information including allowable loads and fasteners, Please See USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. Joist size is adjustable in 2 inch increments. For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting and allows installation on both sides of the supported member. Triple Zinc clips require 10d HDG or 16d HDG nails.  Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages.
USP Lumber AC5-TZ Framing Angle USP Lumber AC Framing Angle
For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting and allows installation on both sides of the supported member. Triple Zinc clips require 10d HDG or 16d HDG nails.  Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages. For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting and allows installation on both sides of the supported member. Triple Zinc clips require 10d HDG or 16d HDG nails.  Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes. For additional information including allowable loads and number of fasteners, please see USP Structural Connectors charts in the Orgill paper catalog R7 Reference Pages.
   
 
1